Miele G 349 Plus Installation Instruction
Installation instructions
for eye-level dishwashers
It is essential to read the operating and
installation instructions before
installing or using the machine,
to avoid the risk of accident or
damage to the machine.
G
M.-Nr. 05 585 961
These installation instructions apply to several different dishwasher models.
Model numbers in this booklet refer to the model designation specified
on the data plate on the machine (and not the description on the control
panel). The data plate is located at the top of the door when open.
The model numbers quoted refer only to the basic model number, e.g. the
G 349SC is described as the G 349 in this booklet.
It is essential to read the Warning and Safety Instructions in the Operating
Instruction booklet before installing the dishwasher.
2
Contents
Building in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1. Measurements for building in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Fitting the control facia panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Fitting the panel front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Adjusting the dishwasher height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. Fitting the drain hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. Building in kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7. Fitting the building-in frame and installing the dishwasher . . . . . . . . . . . . . . . . 12
Apply moisture protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Screw the foot holds and edge protector in place . . . . . . . . . . . . . . . . . . . . . 12
Fitting the side and top frame strips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Fitting the dishwasher into the housing unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Aligning the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To secure the dishwasher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To fix the protective sheet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To fit the bottom frame strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
To fit the plinth facia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8. Adjusting the door springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connection to the water inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Venting the drainage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3
Building in
This dishwasher is intended to be built
into a tall unit.
The following are needed:
A facia panel (GW...),
–
A dishwasher front, consisting of a
–
panel front and plinth facia (GFH 55),
A building in frame (GER 60).
–
The facia panel and the front panel
must be fitted before the dishwasher is
built into the tall unit.
To ensure stability this dish
,
washer must only be built into a tall
unit. It must not be set up as a free
standing machine.
The tall unit should be secured to
the wall for stability with the bracket
supplied.
On dishwashers with a drying
,
fan, moist air is expelled through the
vent outlet in the front of the machine
at the end of a programme. It continues to be expelled for a certain
length of time or until the door is
opened.
To prevent damaging surrounding
fittings (e. g. worktops with wood
edging) the fan running time can be
increased to 45 minutes (see "Additional functions" in the Operating Instruction manual for the machine).
-
-
4
Building in
1.Measurements for building in
The following conditions must be met:
– The recess floor must be capable of
bearing a load of at least 80 kg
– The housing unit must be at least
550 mm deep.
– The installation duct (from base of
the recess to the floor) must be at
least 50 mm deep and 100 mm wide.
.
Normally connection to water is sited
near the dishwasher, for example in the
area under the sink. A Miele sink base
unit already has a suitable cut out for
installation. If the base unit has no
cut-out and if there is no opening
through the plinth area for connections,
one must be made.
Suggested dimensions: 60 x 110 mm.
The same applies to the tall unit in
which this dishwasher is to be installed.
,
There must be no electrical
sockets behind the dishwasher.
Danger of overheating and fire risk if
the dishwasher were to be pushed
up against a plug.
5
Building in
2.Fitting the control facia
panel
The dishwasher must not be used until the control panel has been correctly fit
ted.
Dishwashers with selector dial (G 349)
^ Attach cap a to push button switch.
^ Push the ventilation grille b into posi-
tion so that the slats on the grille are
facing downwards.
^ Place the facia panel c in position
and use the six screws d to secure
in place through from the inside of
the door.
^
Attach selector e.
-
6
Dishwashers with programme selector buttons (G 396)
Building in
^ Attach cap a to push button switch.
^ Push the ventilation grille b into posi-
tion so that the slats on the grille are
facing downwards.
^ Place the facia panel c in position
and use the six screws d to secure
in place through from the inside of
the door.
^ Insert the programme selector buttons
e and function buttons f.
7
Building in
3. Fitting the panel front
^ Hang the panel front into the slits on
the machine door outer panel a.
^ Tighten fixing screws b on both
sides of the door outer panel.
^ Plug openings b using the plastic
stoppers supplied.
4.Adjusting the dishwasher
height
^ Adjust the machine feet evenly until
the height of the dishwasher just
reaches the height of the recess.
^ Press the slides with the ratchet at
the rear under the screw feet.
(You will find the slides in the upper
basket of the dishwasher).
8
Loading...