MIDLAND Geopoint Voice LCD User Manual

User Guide
GEOPOINT LCD
PERSONAL TRACKER
User Guide
GEOPOINT LCD
PERSONAL TRACKER
User Guide
July Edition 2009
Limitation of Liability
The Manufacturer reserves the right to modify the devices or the device specifi cations in this manual without prior notice. Any copy of this manual, in part or in full, whether by photocopy or by other means, even of electronic nature, without the manufacture giving written authorisation, breaches the terms of copyright and is liable to prosecution.
It is absolutely forbidden to use the device for different uses other than those for which it has been devised for, as inferred to in this manual. When using the features in this device, obey all laws and respect privacy and legitimate rights of others.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL THE MANUFACTURER BE LIABLE FOR CONSEQUENTIAL DAMAGES SUSTAINED IN CONNECTION WITH SAID PRODUCT AND THE MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR IT ANY OBLIGATION OR LIABILITY OTHER THAN SUCH AS IS EXPRESSLY SET FORTH HEREIN.
All trademarks in this manual are property of their respective owners.
The information contained in this manual is for information purposes only, is subject to changes without previous notice and cannot be considered binding for the Manufacturer. The Manufacturer assumes no responsibility for any errors or incoherence possibly contained in this manual.
Printed in Italy.
Note for the users of appliances
According to the article 13 of the Legislative Decree no. 151 dated July 25, 2005, “Enforcement of the 2002/95/EC and
2003/108/EC directives, relavant to the reduction of dangerous substances in electric and electronic applinaces, as well as waste disposal”, the symbol of a crossed dustbin applied on appliances or on their cases means that the product at the end of its life cycle must be disposed in a dedicated location than other waste.
The user must, therefore, dispose the aplliance at its end-of-life in the relevant disposal site for electric and electronic waste or give it back to resellers at the time of purchasing a news equivalent one.
The correct disposal and consequant start up of a recycling of the unused appliance, treatment and fi nal disposal compatible to the enviroment concurs to avoid possible negative effects on the enviroment and health and favours the reusing and / or recycling of the parts making the apparatus.
The abusive disposal of such products done by users is fi ned according to the present legislation.
Contents
Safety Instructions ................................................................................................................................... 5
General Information .................................................................................................................................6
Preliminary Procedures ..........................................................................................................................8
Inserting the SIM Card .................................................................................................................... 8
How to Charge the Battery ............................................................................................................. 9
Use of the Tracker ..................................................................................................................................10
Symbols ............................................................................................................................................ 10
Keypad Lock ....................................................................................................................................12
Menu Structure ................................................................................................................................13
GPS .................................................................................................................................................... 14
Phone ................................................................................................................................................. 14
Anchor ............................................................................................................................................... 16
Finder ................................................................................................................................................. 18
Guide ................................................................................................................................................. 19
Speed ................................................................................................................................................ 21
Setup ..................................................................................................................................................22
SOS Key ............................................................................................................................................ 28
Tracker Management by SMS ............................................................................................................30
Position Request ............................................................................................................................. 30
Automatic Position Sending ......................................................................................................... 30
Anchor ............................................................................................................................................... 31
Geofence .......................................................................................................................................... 32
Alarm SMS ........................................................................................................................................ 33
Reading and Writing SMS Commands......................................................................................35
Setup by MyTrack Software ................................................................................................................ 42
Power Save Mode...........................................................................................................................42
Alarm SMS ........................................................................................................................................ 45
Position Data Recording ...............................................................................................................46
Update of the Tracker Firmware Version................................................................................... 47
Maintenance ............................................................................................................................................ 48
Technical Features ................................................................................................................................. 49
Manufacturer’s Limited Warranty ...................................................................................................... 50
Warranty Period ...............................................................................................................................50
Safety Instructions
Safety Instructions
Please read the following safety instructions carefully. Not following them may be dangerous and/or illegal. For further details, please read carefully the user manual complete version contained in the enclosed CD ROM.
Do not switch the device on when prohibited or whenever it could cause any interference or danger.
Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your fi rst • consideration while driving should be road safety.
All wireless devices may be susceptible to interference, which could affect the performance of other • appliances (TV, radio,...).
Switch the device off in hospitals or near medical equipment (hearing aid equipment, pacemaker, ...) the • device could cause interference. Always keep a distance of 20 cm between pacemaker and device.
Wireless and digital devices can cause interference with aircraft equipment.
Do not use the device at a refuelling point. Switch-off when near petrol stations or fuel depots and chemical • plants. The device could interfere with the correct functioning of the electronic equipment.
Do not use the device where blasting is in progress.
Do not use the device for any uses other than those it has been built for. Keep to the instructions as • explained in the product manual.
Only qualifi ed personnel may install or repair this product.
Use only approved accessories and batteries. Do not use incompatible products. The use of nonstandard • products can cause damage to device and/or people.
The batteries must be disposed according to the appropriate modes. The consumer must duly hand in • worn out batteries, either at the appropriate collection points for the general public, in his own town, or wherever batteries of the same kind are sold (compulsory warning according to law on the disposal of batteries).
The device is not water-resistant, keep it dry. Contact with water or any other liquid could cause serious • damage to the device.
5
General Information
General Information
The tracker is a portable device able to transmit its geographical location to a mobile phone or PC in real-time. Moreover, the detected data can be recorded for further analysis.
The tracker is available in two different version:
LCD : GPS tracker with display, phone and 2MB data memory. BOX : GPS tracker without display, without vocal communication and 512kB data memory.
Both trackers can be offered combined in the KIT version, particularly indicated for the use of Finder function, useful for real-time locating.
This User Guide describes the tracker in the LCD version.
The tracker has three basic functions:
locating and transmitting its actual position• sending an SOS message in case of an emergency• voice communication as a mobile phone
The tracker is provided with MyTrack software allowing the tracker management and personal tracking.
The GPS receiver and the GSM device work at higher radio frequencies which can be stopped
by enclosures containing metal and plastic parts.
It is suggested to keep the tracker under light clothes, as external as possible.
Examples of shielding materials: kevlar, carbon fi bre, some polyurethanic and polyamidic resins
especially if black, etc.
Examples of materials which cannot infl uence the radio waves: ABS, ABS+PC, policarbonate,
etc.
For further details on tracker use and functions, please read carefully the user
manual complete version contained in the enclosed CD ROM.
6
General Information
ON/OFF
BUZZER
LOUDSPEAKER
DISPLAY
MICROPHONE
MULTIFUNCTION KEYS
JOG
UP (+)
USB DC IN
HEADSET
DOWN (-)
SCROLL
FUNCTION
SOS KEY
ENTER
PUSH
FUNCTION
7
Preliminary Procedures
Preliminary Procedures
Inserting the SIM Card
In case of a SIM card:
prepaid : the communication between the tracker and the provided software is made exclusively by SMS text or GPRS network. with subscription : the communication between the tracker and the provided software is made by SMS text, GPRS network or also sending/receiving data (only if the data number has been activated by the network provider).
PIN: - - - - - Before inserting the SIM card in the tracker, disable the PIN code by means
30 sec.
To insert the SIM card, remove the back cover and lifting out the battery.
of a mobile phone.
Inserting a SIM card any SMS message, contained in it or which will be
received in the future, will be deleted and cannot be retriveable.
If the battery is not inserted within 30 seconds, the date and hour settings
will be ERASED.
8
Preliminary Procedures
How to Charge the Battery
Before using the tracker for the fi rst time, the battery must be completely charged. Before charging, check that the network electrical supply corresponds to that of the battery charger. Do not exceed the network voltage indicated on the battery charger.
Use only batteries and battery chargers with the following features:
Battery: model ABL-6C Li-ion• Battery charger: model ZD050050EU• Car charger: model ESC-004
The manufacturing company is not liable for any damage to the tracker due to the use of accessories different from those expressly indicated.
Do not leave the tracker in particularly hot or cold environments during the
battery charging. Keep the tracker between -10°C and +40°C environmental temperature.
When the battery is almost discharged, the tracker, if ON, emits an acoustic
warning every minute.
9
Safety InstructionsUse of the Tracker
Use of the Tracker
Symbols
Battery status:
Charged battery Discharged battery
GSM network coverage
The info message changes according to the function in use
SMS sending/receiving
More symbols can be displayed:
Data connection
GPRS connection
10
10
UNLOCK?
Yes 10:30 No
Time
(hh:mm)
The item relevant to the key changes
according to the function in use
GPS signal coverage:
Maximum level
.... FIX procedure
Connection via USB
Activated keypad lock
Connected headphones
Tracker Function Description Refer to
GPS Info on Display
Phone
SOS key
Position Request
Automatic Position Sending
Position Data Recording
Geofence
Anchor
Finder
Guide
Speed
the tracker displays the info relevant to its position
the tracker displays the phonebook and a call can be received or carried out
the tracker sends an alarm message chapter Use of the Tracker
the tracker sends an SMS containing its position to the phone number which requested this data
the tracker sends automatically its position by SMS or by GPRS connection
the tracker records its position data to review the track afterwords
the tracker sends an alarm SMS to the preset phone number everytime it exits or ri-enters in a preset rectangular area
the tracker sends an alarm SMS to the preset phone number everytime it exits or ri-enters in a preset circular area
the tracker fi nds another tracker of the same type and displays the direction and the distance to follow
the tracker fi nds a previously saved destination point and displays the direction and the distance to follow
the tracker emits an acoustic alarm when the preset speed limit has been overcome
chapter Use of the Tracker
chapter Use of the Tracker
chapter Tracker Management by SMS
chapter Use of the Tracker, section Setup chapter Tracker Management by SMS
chapter Use of the Tracker, section Setup chapter Setup by MyTrack Software
chapter Tracker Management by SMS
chapter Use of the Tracker chapter Tracker Management by SMS
chapter Use of the Tracker
chapter Use of the Tracker
chapter Use of the Tracker
Safety Instructions
Use of the Tracker
11
11
Safety InstructionsUse of the Tracker
Tracker Function Description Refer to
Power Save Mode
Alarm SMS
the tracker switches on/off automatically to optimize the battery consumption
the tracker sends alarm SMS to the preset phone number everytime a status change happens (low battery, memory full, ...)
The tracker can work without the SIM card. In this case, all functions operating
with GSM/GPRS network will not be available.
Keypad Lock
The keypad lock disables the keys to avoid accidental use of the tracker.
chapter Setup by MyTrack Software
chapter Tracker Management by SMS chapter Setup by MyTrack Software
SOS It is possible to send an alarm message by means of pressing the SOS key, even when the
keypad lock is activated.
Network Provider
10:30 Menu
12
12
3 sec.
LOCKED
10:30
3 sec.
UNLOCK?
Yes 10:30 No
Safety Instructions
Use of the Tracker
Menu Structure
To access the main menu, press Menu in the Home page. The fi rst section, GPS, will be displayed. Scroll down the sections turning the JOG and press OK to enter into the desired item. To exit the main menu and display the Home page, press Home.
The Speed function is not available in case of tracker compatible for OnTrack
application.
W
GPS
Home 10:30 OK
PHONE
Home 10:30 OK
ANCHOR
Home 10:30 OK
FINDER
Home 10:30 OK
GUIDE
Home 10:30 OK
SPEED
Home 10:30 OK
SETUP
Home 10:30 OK
13
13
Safety InstructionsUse of the Tracker
GPS
The data received by the GPS system are shown on the display.
GPS
Home 10:30 OK
Lat: 45°45.67N Long: 08°12.34E Alt: 256 m
Back 10:30
Spd: 20km/h Dir: 270° Sat: 8-3D FIX
Back 10:30
Phone
The tracker also works as a GSM telephone. The call functions are extremely simple. The phone numbers and names are pre-programmed in the phone book by means of the provided software.
14
14
PHONE BOOK (MAX 10 NUMBERS)
Safety Instructions
Use of the Tracker
PHONE
Home 10:30 OK
RECEIVING A CALL
Incoming Call...
+123456789
Reject Answer
During the transfer of data between the tracker and PC, it is not possible to
make or receive any calls.
The tracker does not allow to use the phone book possibly memorized on the
SIM card in use. However, the information contained in it, except for SMS
SIM
messages saved by a mobile phone, will not be erased.
John
+123456789
Back Call
00:05
+123456789
Hungup
Back Call
       
VOL:
Back
Mary
+123456789
15
15
Safety InstructionsUse of the Tracker
Anchor
The Anchor function allows to monitor within a pre-established circular area the position of a person, an object or an animal. When the tracker detects the exiting from the pre-established area or the ri-entering, it sends an alarm SMS containing its position data to the preset phone number. This function is programmable either operating directly on the tracker or by the provided software or by sending an SMS command.
Area centre to be monitored
Anchor Disabled
Dist:
ANCHOR
Home 10:30 OK
Available values: 50, 100, 200, 300, 500, 700, 1000, 1500, 2000, 3000, 4000 meters
Limit: 100 m
Change
Torna 10:30 OK
Max 50m
Set Center:
Lat: 45°45.67N Long: 08°12.34E
Back Center
Anchor Enabled Dist: 45 m Limit: 50 m
Change
Back 10:30 OK
16
16
Set Limit:
0 m
Back OK
Anchor Enabled Dist: 45 m Limit: 50 m
OFF
Back 10:30 OK
Set Limit:
50 m
Back OK
Anchor Disabled Dist: Limit: 50 m
Change
Back 10:30 OK
Safety Instructions
Use of the Tracker
Before enabling this function, it is necessary to set the phone number where
SMS will be sent by means of the provided software.
Example of the SMS message displayed on the mobile phone, when the tracker enters the area
GEO,ID:GLORIA,ANCHOR ENTER,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the tracker exits the area
GEO,ID:GLORIA,ANCHOR EXIT,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
The SMS message structure of the Anchor function is described here below:
GEO Tracker type. ID:−−−−−− Tracker name preset by the user through the provided software. ANCHOR ENTER Alarm message. POS:−−−−−.−−−−−,−−−−−.−−−−− Latitude and longitude of the geographical position. ALT:−−−−.− Altitude in m.
−−/−−/−−,−−:−− Event date and time (yy/mm/dd hh:mm).
17
17
Safety InstructionsUse of the Tracker
Finder
The Finder mode allows to fi nd another tracker of the same type (LCD or BOX version) by displaying the distance and the direction to follow. The Finder function can only be used if the distance between the trackers is less than 999 Km.
To carry out the Finder function, set the communication rate by the provided
software.
The necessary motion for updating the relevant position, must be no less than 10
meters in 3km/h. More motion means more precise indication of direction. It is important to
keep the tracker pointing in the direction used for reference. In every way, if change of direction is inevitable, e.g. the ground is not viable, on approaching the correspondent, the direction will be constantly updated and corrected by the tracker.
PHONE BOOK
FINDER
Home 10:30 OK
350 m
Torna
18
18
Mary
+123456789
Back 10:30 OK
No Phone
Numbers in the
PHONE Book!
Back
350 m
Back Detail
No Connection...
Retry?
Yes 10:30 No
Absence of GSM or GPS signal / Selected voice not corresponding to a tracker
Dest: Mary Lat: 45° 12.34N Long: 08° 12.34E Dist: 350 m
Back 10:30
Safety Instructions
Use of the Tracker
Guide
The Guide function allows to reach a destination point by displaying the distance and direction. The Guide function is available only if the distance between the tracker and destination point is less than 999 Km. It is possible to set the Guide function by means of the provided software or directly on the tracker.
3D FIX It is suggested to save the destination point when the GPS signal level
is optimal. In case of weak GPS signal, the accuracy of destination point coordinates will not be guaranteed.
HOW TO SAVE A DESTINATION POINT (MAX 30 POINTS)
GUIDE
Home 10:30 OK
---
01 02 --­03 --­04 ---
Back OK
Point 01
01 02 --­03 --­04 ---
Back OK
3 sec.
3 sec.
Save As Dest: Point 01 Lat: 45° 12.34N Long: 08° 12.34E
Yes 10:30 No
Overwrite Data?
Yes 10:30 No
19
19
Safety InstructionsUse of the Tracker
HOW TO REACH A DESTINATION POINT
The necessary motion for updating the relevant position, must be no less than 10
meters in 3km/h. More motion means more precise indication of direction. It is important to
keep the tracker pointing in the direction used for reference. In every way, if change of direction is inevitable, e.g. the ground is not viable, on approaching the correspondent, the direction will be constantly updated and corrected by the tracker.
GUIDE
Home 10:30 OK
350 m
Torna
20
20
HOME
01 CASA 02 --­03 --­04 ---
Back OK
No GPS Signal
NO POINT
350 m
Back Detail
Selected point not set
Dest: HOME Lat: 45° 12.34N Long: 08° 12.34E Dist: 350 m
Back 10:30
Safety Instructions
Use of the Tracker
Speed
The Speed function allows to set a speed limit which, when exceeded, causes the emission of a progressive acoustic alarm: more is the difference between the real speed and that programmed, quicklier will be the alarm reproduction.
The Speed function is not available in case of tracker compatible for OnTrack
application.
SPEED
Home 10:30 OK
100km/h
Back 10:30 ON
(OFF) DISABLE
(ON) ENABLE
101km/h
100
Back 10:30 OFF
21
21
Safety InstructionsUse of the Tracker
Setup
HOW TO ENABLE THE CYCLIC POSITION SMS SENDING
For further details on this function, refer to the chapter Tracker Management by SMS, paragraph Automatic Position Sending.
SETUP
Home 10:30 OK
Tracking
GPRS rate OFF
Back 10:30 OK
22
22
OFF
Main
Tones Memory
Back 10:30 OK
Tracking
GPRS rate OFF
Back 10:30 OK
ON
Tracking
GPRS rate OFF
Back 10:30 OK
Tracking
GPRS rate OFF
Back 10:30 OK
OFF
ON
HOW TO SELECT THE RATE FOR CYCLIC GPRS CONNECTION
Safety Instructions
Use of the Tracker
Main
SETUP
Home 10:30 OK
Tracking
GPRS rate
Back 10:30 OK
Before rate selection, check if the GPRS parameters have been set properly.
Tones Memory
Back 10:30 OK
OFF OFF
Tracking
GPRS rate
10:30 OK
OFF
OFF
Available values: OFF, 1m, 5m, 10m, 15m, 30m, 1h, 2h, 4h, 8h, 12h, 18h, 24h.
Tracking
GPRS rate OFF
Back 10:30 OK
Tracking
GPRS rate
10:30 OK
Tracking
GPRS rate
Back 10:30 OK
OFF
OFF
1m
OFF 1m
23
23
Safety InstructionsUse of the Tracker
TONES SETUP
SETUP
Home 10:30 OK
Ring
Call HIGH Keys OFF SOS ON
Back 10:30 OK
Ring
Call HIGH Keys OFF SOS ON
Back 10:30 OK
24
24
Main
Tones Memory
Back 10:30 OK
1
2
Ring
Call HIGH Keys OFF SOS ON
Back 10:30 OK
Ring
Call
Keys OFF SOS ON
Back 10:30 OK
1
2
HIGH
Main
Tones
Memory
Back 10:30 OK
Ring
Call HIGH Keys OFF SOS ON
Back 10:30 OK
2
Safety Instructions
Use of the Tracker
Ring Select the call tone type. Call Set the call tone volume.
OFF: tone disabled. In case of a call, the tracker will not emit any acoustic signal. LOW: tone with a low volume level. HIGH: tone with a high volume level.
Keys Enable/disable the keys tone. SOS Enable/disable the acoustic signal tone for the SOS key.
RECORDINGS
The tracker allows to record:
the detected events automatically without setting the recording• the position data to review the track afterwords, if the recording was previously set
The tracker can records approx. 70,000 position points and approx. 1,900 events. When an event occurs, the tracker detects it and start to record in the Event LOG.
The following list shows all the events which can be detected and recorded automatically by the tracker.
power on/off• low battery• making or receiving a voice call• receiving a data call• making a GPRS call• hanging up a call• motion on/off• GSM network available/unavailable
GPS signal available/unavailable• entry/exit from Geofence area• entry/exit from Anchor area• fi rmware update• SOS alarm• memory erasing• roaming on/off• network GSM provider changing if roaming on
25
25
Safety InstructionsUse of the Tracker
SETUP
Home 10:30 OK
Rate
Distance 0 Mode OFF Erase
Back 10:30 OK
Rate
Distance 0 Mode OFF Erase
Back 10:30 OK
26
26
Main
Tones Memory
Back 10:30 OK
0
1
Rate
Distance 0 Mode OFF Erase
10:30 OK
Rate
Distance
Mode OFF Erase
Back 10:30 OK
0
1 0
Main Tones
Memory
Back 10:30 OK
Rate
Distance 0 Mode OFF Erase
10:30 OK
1
Safety Instructions
Use of the Tracker
The setup of the position points recording can be carried out by means of the provided software or directly on the tracker.
Rate Set the temporal recording rate. Available values: 0, 1, 5, 10, 30, 60, 300 seconds. By
Distance Set the distance (in meters) to cover. Available values: 0, 10, 50, 100, 500, 1km. By selecting
Mode Select the memory recording mode.
Erase Delete all data contained in the memory.
selecting 0, the recording at temporal rate is disabled.
0, the recording for covered distance is disabled.
FILL: after having fi nished all the available memory space, stop recording (the oldest data is kept). RING: after having fi nished all memory space, the data already recorded is overwritten (the latest data is kept). OFF: disable the recording.
The Erase function deletes all GPS data contained in the tracker memory. Once deleted, the
data is no longer retrievable.
If the Power Save Mode with position SMS or cyclic GPRS has been enabled, the
tracker position will be recorded at each automatic switching ON. The set Rate and Distance parameters will not be considered.
27
27
Safety InstructionsUse of the Tracker
SOS Key
By pressing the SOS key for at least 2 seconds, for 5 consecutive times every minute, an SMS message is immediately sent to the preset phone numbers (max. of 4 phone numbers), and a brief acoustic warning signal is emitted at SMS sending (refer to the paragraph Setup). This message also contains the current data on the location, if the GPS signal has been revealed. If there is no GPS signal coverage, the last position data will be sent.
Back to previous page without disable the SOS sending
Pressed for at least 2 sec. disable the SOS sending
28
28
SOS Sending
Back Cancel
If SOS tone is enabled
SOS
GSM Signal
missing
SMS not sent!
Back Cancel
If there is no GSM signal If there is no SOS number or
SOS No or SMS
center missing!
SOS not sent!
Back
no SMS center number set
SOS Sent!
If SOS is sent
SMS error!
SOS not sent!
Back
If the previously set SMS center number is not correct
Safety Instructions
Use of the Tracker
If no numbers have been set or in the absence of GSM signal, every time the
SOS key is pressed, an acoustic warning signal is emitted.
In the event that there is no network service coverage, the alarm functions
GSM
may not be available.
Example of the SMS message displayed on the mobile phone, with the detected current position data
GEO,ID:GLORIA,SOS ALARM,POS:45g37.9480N,008g28.9992E,ALT:0218m,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, with the last position data detected before the GPS signal loss
GEO,ID:GLORIA,SOS ALARM,LAST POS:45g37.9480N,008g28.9992E,ALT:0218m,07/04/10,10:09
The SMS message structure of the SOS function is described here below:
GEO Tracker type. ID:−−−−−− Tracker name preset by the user through the provided software. SOS ALARM Alarm message. POS:−−−−−.−−−−−,−−−−−.−−−−− Latitude and longitude of the geographical position. ALT:−−−−.− Altitude in m.
−−/−−/−−,−−:−− Event date and time (yy/mm/dd hh:mm).
29
29
Safety InstructionsTracker Management by SMS
Tracker Management by SMS
Position Request
It is possible to ask for the tracker position by means of an SMS command. After receiving the SMS command, the tracker sends a message containing the position data to the phone number which sent the command.
To know the tracker position in real time, send the following command: For further details, refer to the paragraph Reading and Writing SMS Commands.
Automatic Position Sending
The tracker can send its own position at a programmable rate. The automatic position sending can be carried out in two different modes:
by SMS• by GPRS connection
CYCLIC POSITION SMS
The tracker can send an SMS message at intervals, containing all the information on its current position. This function is useful for monitoring the tracker motion at a distance by a mobile phone. To use this function, it is necessary to:
set, using the provided software, the phone number where the position messages will be sent• set the rate for cyclic position SMS using the provided software or sending an SMS command enable the function using the provided software or sending an SMS command
rpos
30
30
Tracker Management by SMS
CYCLIC GPRS CONNECTION
The cyclic GPRS connection allows to connect the tracker automatically at a programmed rate for the continuous position updating. At the programmed rate, the tracker will be connected only for the time needed for sending the position point. This function is very useful if combined with the I-Scout web server as it allows to display the detected positions by every station connected to internet.
To use this function, it is necessary to:
set the GPRS parameters using the provided software or sending an SMS command enable the function setting the rate for the cyclic GPRS connection using the provided software
Safety Instructions
Anchor
The Anchor function allows to monitor within a pre-established circular area the position of a person, an object or an animal. When the tracker detects the exiting from the pre-established area or the ri-entering, it sends an alarm SMS containing its position data to the preset phone number.
This function is programmable using the complete SMS command (enabling and radius setting), either operating directly on the tracker, or partially by the provided software.
When the complete SMS command is received by the tracker (e.g. wanc=1,0500), the function is enabled and the current tracker position is considered as area central point. If the function is enabled without setting the radius, the previously set coordinates for the central point and the last programmed radius will be considered. If no radius was previously programmed, by default it will be set to 100 m.
This function is programmable completely by SMS command (wanc), either operating directly on the tracker. By the provided software, only function enabling and radius setting is possible.
Before enabling this function, it is necessary to set the phone number where
SMS will be sent by means of the provided software.
31
31
Safety InstructionsTracker Management by SMS
Example of the SMS message displayed on the mobile phone, when the tracker enters the area
GEO,ID:GLORIA,ANCHOR ENTER,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the tracker exits the area
GEO,ID:GLORIA,ANCHOR EXIT,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
The SMS message structure of the Anchor function is described here below:
GEO Tracker type. ID:−−−−−− Tracker name preset by the user through the provided software. ANCHOR ENTER Alarm message. POS:−−−−−.−−−−−,−−−−−.−−−−− Latitude and longitude of the geographical position. ALT:−−−−.− Altitude in m.
−−/−−/−−,−−:−− Event date and time (yy/mm/dd hh:mm).
Geofence
The Geofence function allows to monitor the entry and the exit of the tracker in a pre-established area. This is a rectangular area and can be programmed by set the area diagonal coordinates by means of the provided software, or by means of an SMS command sent by a mobile phone. To set the SMS command, refer to the paragraph Reading and Writing SMS Commands.
After having set the parameters of the Geofence function, the tracker will send an SMS message of alarm to the preset phone number (set by means of the provided software) each time it enters/exits the pre-established area or each time it is switched on outside the pre-established area.
32
32
Tracker Management by SMS
Example of SMS message displayed on the mobile phone, when the tracker enters the area
GEO,ID:GLORIA,GEOFENCE ENTER,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the tracker exits the area
GEO,ID:GLORIA,GEOFENCE EXIT,POS:45g37.9481N,008g28.9992E,ALT:0218m,07/04/10,10:09
The SMS message structure of the Geofence function is described here below:
GEO Tracker type. ID:−−−−−− Tracker name preset by the user through the provided software. GEOFENCE ENTER Alarm message. POS:−−−−−.−−−−−,−−−−−.−−−−− Latitude and longitude of the geographical position. ALT:−−−−− Altitude in m.
−−/−−/−− −−:−− Event date and time (yy/mm/dd hh:mm).
Safety Instructions
Alarm SMS
The Alarm SMS are alarm messages sent (if the function has been enabled by the provided software) to a phone number every time that:
the tracker battery is almost discharged• the tracker memory is full• the GPRS network is available• the GPRS network is not available• the GPS signal of the tracker has been lost• the GPS signal of the tracker has been restored• tracker motion is revealed• the tracker motion stops
33
33
Safety InstructionsTracker Management by SMS
This function can only be programmed by means of the provided software.
Example of the SMS message displayed on the mobile phone, when the tracker battery is almost discharged
GEO,ID:GLORIA,LOW BATTERY,07/04/10,10:09
Example of the SMS message displayed on the mobile phone,when the tracker memory is full
GEO,ID:GLORIA,MEMORY FULL,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the GPRS network is available
GEO,ID:GLORIA,GPRS OK,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the GPRS network is not available
GEO,ID:GLORIA,GPRS OFF,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when there is GPS signal
GEO,ID:GLORIA,GPS FIX OK,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when the GPS signal has been lost
GEO,ID:GLORIA,NO GPS FIX,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when a tracker motion is revealed
GEO,ID:GLORIA,MOTION ON,07/04/10,10:09
Example of the SMS message displayed on the mobile phone, when tracker motion stops
GEO,ID:GLORIA,MOTION OFF,07/04/10,10:09
34
34
Tracker Management by SMS
The SMS message structure of the Alarm SMS function is described here below:
GEO Tracker type. ID:−−−−−− Tracker name preset by the user through the provided software. LOW BATTERY Alarm message.
−−/−−/−− −−:−− Event date and time (yy/mm/dd hh:mm).
Safety Instructions
Reading and Writing SMS Commands
The SMS commands allows to set or read some tracker settings. These messages can be sent by a mobile phone or by a GSM device able to send/receive SMS (i.e. a GSM modem). When the tracker is switched ON and there is GSM signal, it can receive any SMS command. If the tracker receives a correct SMS command, an answer is sent to the SMS command sender. If the message contains invalid characters, the tracker will not reply. If it contains invalid values, the tracker will reply a message containing “COMMAND ERROR“. All commands start with the letter “r” (reading) or “w” (writing).
Ensure that the SMS commands are written exactly as shown in the table. Any
change (space, capital letter, small letter,...) could affect the recognition of the command.
Before enabling the sending of position SMS in cyclic mode (wposc), ensure
that the SMS phone number has been programmed.
35
35
Safety InstructionsTracker Management by SMS
Reading Commands
Command
rpos Read instantaneous GPS position data.
The tracker can reply in 3 different ways:
A) POS: <position data> = GPS position in real time.
B) LAST POS: <position data> = no GPS signal. The reply message contains the last detected GPS data.
C) POS: NO GPS DATA = from the tracker switching on, the GPS signal has not been detected.
NOTE: the date and time refer to:
rposc Read cyclic position SMS setup and power save
36
36
mode status. [status: 0=disabled, 1=enabled] [rate: 01÷99 minutes] [power save mode: 0=disabled, 1=enabled]
Meaning and Values Example
SMS sending, in case of Reply A• last detected GPS data, in case of Reply B
Command: rpos Reply A:
POS:41g37.8283N,012g28.8191E, ALT:0262m,DIR:023g,SPEED:0050km/h, SAT:09,07/05/26,15:56
Reply B:
LAST POS:45g37.8283N, 008g28.8191E,ALT:0262m, DIR:023g,SPEED:0050km/h, SAT:09,07/05/26,15:56
Reply C:
POS: NO GPS DATA
Description: 41g37.8283N Lat. in degree, min. 012g28.8191E Long. in degree, min. 0262m Altitude in m 023g Direction in degree 0050km/h Speed in km/h 09 Satellites number 07/05/26 Date (yymmdd) 15:56 Time (hhmm)
Command: rposc Reply: rposc=1,01,0
Description: 1=enabled cyclic position SMS 01=1 minute rate 0=disabled power save mode
Tracker Management by SMS
Safety Instructions
Command
rms Read the accelerometer setup values.
[sensitivity: 00=disabled sensor, 01=maximum, 10=minimum] [timeout: 01÷99 minutes]
rgf Read the Geofence setup.
[status: 0=disabled, 1=enabled] [LAT1,LONG1,LAT2,LONG2=latitude and longitude of the 2 points which defi ne the Geofence area]
ranc Read the Anchor setup.
[status: 0=disabled, 1=enabled] [radius: 0050, 0100, 0200, 0300, 0500, 0700, 1000, 1500, 2000, 3000, 4000 m]
Meaning and Values Example
Command: rms Reply: rms=02,10
Description: 02=sensitivity level 2 10=10 minutes timeout
Command: rgf Reply:
rgf=1,45g37.7981N,008g28.8012E, 41g37.8971N,012g28.8012E
Description: 1=enabled 45g37.7981N,008g28.8012E=latitude and longitude of the fi rst point 41g37.8971N,012g28.8012E=latitude and longitude of the second point
Command: ranc Reply: ranc=1,0100
Description: 1=enabled 0100=radius at 100 m
37
37
Safety InstructionsTracker Management by SMS
Writing Commands
Command
wposc Set the cyclic position SMS in text format and the
wms Set the accelerometer values.
38
38
relevant power save mode. [enabling: 0=disable, 1=enable] [rate: 01÷99 minutes] [power save mode: 0=disable, 1=enable]
NOTE: the power save mode works only with SMS rate5 minutes. Never set like this: wposc=0,xx,1
NOTE: to enable or disable only the cyclic position SMS, send the wposc command with the fi rst fi eld only. In this case, the previously set rate is considered.
[sensitivity: 00=disables sensor, 01=maximum, 10=minimum] [timeout: 01÷99 minutes]
Meaning and Values Example
Case A Command: wposc=1,01,0 Reply: wposc=1,01,0 OK
Description: 1=enables the cyclic position SMS 01=1 minute rate 0=disables the power save mode
Case B Command: wposc=1 Reply: wposc=1 OK
Description: 1=enables the cyclic position SMS with the previous set rate
Command: wms=02,10 Reply: wms=02,10 OK
Description: 02=sensitivity level 2 10=10 minutes timeout
Tracker Management by SMS
Safety Instructions
Command
wgf Set the Geofence.
[status: 0=disable, 1=enable] [LAT1,LONG1,LAT2,LONG2=latitude and longitude for the 2 points defi ning the Geofence area]
NOTE: to enable or disable the Geofence function without setting the area, sent the wgf command with the fi rst fi eld only.
Meaning and Values Example
Case A Command:
wgf=1,45g37.7981N,008g28.8012E, 41g37.8971N,012g28.8012E
Reply:
wgf=1,45g37.7981N,008g28.8012E, 41g37.8971N,012g28.8012E OK
Description: 1=enable 45g37.7981N,008g28.8012E=latitude and longitude of the fi rst point 41g37.8971N,012g28.8012E=latitude and longitude of the second point
Case B Command: wgf=1 Reply: wgf=1 OK
Description: 1=enables the function considering the previous defi ned area
39
39
Safety InstructionsTracker Management by SMS
Command
wanc Set the Anchor.
wem Erase all position data recorded in the memory. Command: wem
40
40
[enabling: 0=disable, 1=enable] [radius: 0050, 0100, 0200, 0300, 0500, 0700, 1000, 1500, 2000, 3000, 4000 m; default radius: 0100]
NOTE: to set the tracker current position as area center point, send the complete wanc command, containing both enabling and radius fi elds (e.g. wanc=1,0100).
NOTE: to enable or disable the Anchor function without setting the radius, send the wanc command with the fi rst fi eld only. In this case, the default radius or the previously set radius is considered.
Meaning and Values Example
Case A Command: wanc=1,0100 Reply: wanc=1,0100 OK
Description: 1=enables 0100=radius at 100 m
Case B Command: wanc=1,0100 Reply: NO VALID CENTER POS
Description: 1=enables 0100=radius at 100 m NO VALID CENTER POS=if the center point cannot be detected
Case C Command: wanc=1 Reply: wanc=1 OK
Description: 1=enables the function considering the default radius or the previously set radius
Reply: wem OK
Tracker Management by SMS
Safety Instructions
Command
wgprs Set the GPRS parameters and start the continuous
GPRS connection. [setup: 0=set the GPRS parameters without starting the connection, 1=connect with the new parameters (IP, PORT), 2=connect with the parameters previously preset] [parameters: IP=host IP address, PORT=TCP port]
NOTE: the IP and PORT parameters should be written between commas.
NOTE: if there is no GPRS connection, the tracker sends an error SMS containing “GPRS ERROR”.
Meaning and Values Example
Case A Command:
wgprs=0,”213.86.89.11”,”9500”
Reply:
wgprs=0,”213.86.89.11”,”9500” OK
Description: 0=set GPRS parameters without starting the connection
213.86.89.11=host IP address (example) 9500=TCP port
Case B Command:
wgprs=1,”213.86.89.11”,”9500”
Reply:
wgprs=1,”213.86.89.11”,”9500” OK
Description: 1=GPRS connection with new parameters
213.86.89.11=host IP address (example) 9500=TCP port
Case C Command: wgprs=2 Reply: wgprs=2 OK
Case D Reply: NO GPRS COVERAGE
Description: NO GPRS COVERAGE=if GPRS signal is missing
41
41
Safety InstructionsSetup by MyTrack Software
Setup by MyTrack Software
INCREASE THE
RECORDING
BAR TO SCROLL
RECORDING
THE
MYTRACK
SETUP
OPEN
ADDRESS BOOK
PRINT
CONNECT
PAGE SETUP
GEOPOINT
SETUP
INFORMATION
DISCONNECT
ZOOM
BAR
ZOOM
PAN
CENTER
FOLLOW
HELP
PLAY
PAUSE
STOP
REWIND
LAST
FIRST
FORWARD
Power Save Mode
The Power Save Mode allows for optimal management of the battery tracker. It is possible to set the tracker automatic switching on/off according to specifi c use requirements. There are three Power Save Modes programmable by means of the provided software, except for Cyclic Position SMS which is programmable by SMS command too. After Power Save Mode enabling, the tracker will switch off automatically 2 minutes after tracker disconnection by the provided software.
WITH MOTION
OFF ON
MOTION
Network Provider
10:30
NO MOTION FOR A PRESET TIME, NO DATA EXCHANGE
SPEED
RECORDING
DECREASE THE
RECORDING
OFF
SPEED
SPEED
42
42
Setup by MyTrack Software
WITH CYCLIC POSITION SMS
OFF ON OFF
Safety Instructions
CYCLIC POSITION SMS SENDING SMS SENT
Network Provider
10:30
Before using this mode, enable and set the Cyclic Position SMS function with
SMS rate 5 minutes.
During the automatic switching on, if the tracker is connected by the provided software, the automatic switching off will be carried out after position SMS sending, after carrying out all the preset operations and 2 minutes after tracker disconnection.
WITH CYCLIC GPRS CONNECTION
OFF ON OFF
CYCLIC GPRS CONNECTION
Network Provider
10:30
Before using this mode, enable and set the Cyclic GPRS Connection function
with rate 5 minutes.
The tracker will switch off automatically after successfull GPRS connection and after carrying out all the preset operations. If, after two tries, the GPRS connection is failed, the tracker will switch off automatically.
43
43
Safety InstructionsSetup by MyTrack Software
To a set a Power Save Mode, connect the tracker to the provided software and access the setup window by selecting Setup from Remote Unit menu.
44
44
Setup by MyTrack Software
Safety Instructions
Alarm SMS
To enable/disable the Alarm SMS and set the phone number, connect the tracker to the provided software and access the setup window by selecting Setup from Remote Unit menu.
45
45
Safety InstructionsSetup by MyTrack Software
Position Data Recording
To set a data position recording, connect the tracker to the provided software and access the setup window by selecting Setup from Remote Unit menu.
46
46
Setup by MyTrack Software
Safety Instructions
Update of the Tracker Firmware Version
To update the tracker, connect the tracker to the provided software and access the info window by selecting Info from Remote Unit menu.
A new window is opened for update fi le selection
During tracker fi rmware upgrade, on the tracker will be displayed UPGRADE...Please don’t turn OFF the device!. Wait until the update is completed, this occurs when the tracker is turned off.
If the tracker to be updated is connected with GSM/GPRS network, be sure
that the GSM/GPRS network signal level is high.
If the tracker to be updated is connected by a USB cable, do not remove the
cable during the update.
To perform the update, it is necessary to connect the provided battery charger
to the tracker.
47
47
Safety InstructionsMaintenance
Maintenance
The tracker and relevant accessories must be handled with care. Read the following instructions carefully.
Clean the tracker with a soft cloth, avoiding the use of corosive chemical products, solvents or aggressive • detergents. Do not paint the tracker.• Do not swallow the accessories or small components of the tracker.• Avoid blows to the tracker which could internally damage the product.• Do not open the tracker in any way differently from the way indicated in the manual. • Do not wet the tracker. Humidity, condensation, rain or any other liquids containing mineral substances • could damage the electronic circuits. In the event of contact with liquids, remove the battery and leave the tracker to dry. Do not use or leave the tracker in particularly hot environments. High temperatures could damage the • electronic circuits, the battery and the plastic parts of the tracker. Do not use or leave the tracker in particularly cold environments. Low temperatures could cause damage • to the electronic circuit boards of the tracker. Do not use or leave the tracker in particularly dirty or dusty environments, the tracker could get • damaged.
48
48
Safety Instructions
Technical Features
Technical Features
GPS receiver: SiRFstarIII - 20 channels GSM frequencies: 850 / 900 / 1800 / 1900 MHz Data memory: 2MB non-volatile FLASH Porta di comunicazione: no.1 USB Sensor: no.1 for accelerometer Dimension/Weight: 74 x 74 x 23 mm / 120 gr Battery: model ABL-6C Li-ion - 3,7V 1000mAh Battery charger: model ZD050050EU input 100VAC - 240V 50/60Hz 0,15A output 5VDC 500mA Car charger: model ESC-004 input 13,6VDC output 5VDC 500mA Conformity: CE mark
CONDITION BATTERY LIFE
Standby mode with motion sensor active. ~10 days
Tracking SMS every minute (GPS always on). ~9 hours
Tracking SMS every 5 minutes (GPS with hotstart). ~4 days
Continuous tracking. ~2 hours
Data connection, with GPS system continuously active. ~2 hours
Position data recording every minute. ~37 hours
Tracker not in use. ~2 days
Tracker in communication on GSM network. ~4 hours
49
49
Safety InstructionsManufacturer’s Limited Warranty
Manufacturer’s Limited Warranty
This warranty does not limit the user’s (statutory) rights under applicable national laws relating to the sale of consumer products. During the warranty period, the Manufacturer or Manufacturer authorized service company will in a commercially reasonable time remedy defects in materials, design and workmanship free of charge by repairing. The Manufacturer will, in accordance with this Limited Warranty (unless otherwise required by law), remedy defects by repair or, should the Manufacturer in its discretion deem it necessary, replace the Product.
This Limited Warranty is only valid and enforceable in the country where the user has purchased the Product provided that the same Product has been intended for sale in that country by the Manufacturer. However, if the user has purchased the Product in a member state of the European Union, Iceland, Norway, Switzerland or Turkey and such Product was originally intended by the Manufacturer for sale in one of these countries, this Limited Warranty is valid and enforceable in all of these above listed countries. Some limitations to the warranty service may apply because of country specifi c elements in the Products.
Warranty Period
The warranty period starts at the time of Product’s original purchase by the fi rst end-user. The Product may consist of several different parts and different parts may be covered by a different warranty period. The different Warranty Periods are:
24 months for the device• 6 months for the following consumable parts and accessories: battery, chargers, headset, device cover• 90 days for the media on which any software is provided, (e.g. CD ROM, DVD,...)
As far as national laws permit, the warranty period will not be extended or renewed or otherwise affected due to subsequent resale, repair or replacement of the Product authorized by the Manufacturer.
50
50
www.cte.it
Distributed by
www.cte.it
Loading...