Midland BR02 PRO User guide

BR02 PRO
BUSINESS RADIO
Instruction guide
Suitable for:
Business Restaurants Hospitality Warehousing
Index
Programming software (optional) 2
Content 3
Main characteristics 3
Main controls and parts of the radio 4
Operations 5
Power on/o and volume adjustment 5
Transmission 5
Monitor 6
Scan 6
Squelch 7
Battery recharge 7
Maintenance 8
Technical specifications 9
Troubleshooting 11
BR02 instruction guide | 1
Thanks for choosing Midland! BR02 PRO is a portable transceiver that is free use in almost all European countries. For further information, we suggest you look at the “Restrictions on the use” chart.

Programming software (optional)

Thanks to Midland Programming software PRG-10, it is possible to incre- ase the performance of your radio or to reduce its functionality by disa­bling some of the default features (CTCSS, DCS, Squelch...) For further information, please consult the Programming software ma­nual. Any attempt to change frequencies of the radio invalidates the approval.
2 | BR02 instruction guide

Content

• 1 BR02 PRO transceiver
• 1 belt clip
• 1 wall adaptor
• 1 1800mAh Li-ion rechargeable battery pack
• 1 desktop charger

Main characteristics

• PMR446 Transceiver
• 16 PMR446 channels: 8+8 pre-programmed
• Frequency band: 446.00625 ÷ 446.09375MHz
• Output power: ≤ 500mW ERP
• Stronger case for heavy duty
• 30% louder speaker
• 38 CTCSS tones/104 DCS codes
• Channel spacing: 12.5KHz
• Scan
• Vocal tuning
• Battery save
• Monitor
• Squelch with 10 selectable levels
• Battery life up to 21 hours Li-Ion battery pack 1800mAh 3.7V
• PC programmable

Coverage/Range

The maximum range depends on terrain condition and is obtained during use in an open space. The only limitation to maximum possible range are environmental factors such as blockage caused by trees,buildings, or other obstructions. Inside a car or a metallic constructions, the range can be re­duced. Normally the coverage in the city, with buildings or other obstruc­tions is about 1 or 2 Km. In open space but with obstructions like trees, leaves or houses the maximum possible range is about 4-6 Km. In open space, without obstructions and in sight, like for example in mountain, the coverage can be more than 12 Km.
BR02 instruction guide | 3

Main controls and parts of the radio

1
2 3
6
4
MIC
10
5
7
8
9
1. Antenna
2. Encoder: rotate clockwise or counter-clockwise to select the desired
channel
3. Power/volume knob- turn clockwise to power on and increase the
volume level. Turn counter-clockwise to decrease the volume level and power o.
4. Speaker
4 | BR02 instruction guide
5. Built-in microphone
6. Led indicator:
RED: TX; GREEN: RX.
7. PTT: push this button to transmit, release it to receive.
8. Function key 1: hold down this button to activate the Monitor fun-
ction.
9. Function key 2: keep pressed for 3 seconds to activate the SCAN
function.
10. External Speaker/Mic Jack- allows the connection with external de-
vices such as headsets, microphones.

Operations

Power on/o and volume adjustment
Rotate the Power/Volume knob clockwise to turn the radio on. Rotate the control clockwise /counter-clockwise to adjust the volume le­vel as you prefer. To turn the radio o, rotate the control counter-clockwise till hearing a mechanical “click”.

Transmission

To communicate, all radios in your group must be set to the same channel. Briefly press the Function key 1 to enable the Monitor feature in order to make sure that the frequency is not busy, then press the PTT button. Release the PTT key to receive.
Only one user at a time can talk during radio communications. Therefore, it is important not to transmit when you are receiving a communication and use the transmission mode sparingly to allow other users to talk. Transmission consumes a significant amount of energy and should therefore be used sparingly to prolong the battery life. If you are unable to contact a station that you have no problems in receiving, the station may be using CTCSS tones or DCS codes.
BR02 instruction guide | 5

Monitor

The Monitor feature is for excluding (opening) the Squelch, in order to li­sten to signals that are too weak to keep the Squelch permanently opened. Hold down the Function key 1 to enable such function.

Scan

1. To begin scanning, press and hold the Scan button for 3 seconds. Your
radio will beep twice alerting you that the radio has entered the scan mode.
2. When in Scan Mode, the radio will rapidly scan through all program-
med channels and will pause on any active channel. While Scan Fun­ction is active the Green LED will flash to indicate that the radio is scanning.
3. After stopping on an active channel, scanning will resume once there
has been 4 seconds of no activity on the channel.
4. To reply to a received transmission when the Scan Mode is enabled,
press and hold the PTT button (on radio or headset accessory) while the radio is paused on the active channel, the radio will then transmit on the active channel’s frequency. The radio will remain on the active channel for 4 seconds after the PTT button is released.
5. To transmit on the frequency selected by the Channel Knob while
Scan Mode is enabled, the user will verify that the radio is not re­ceiving a transmission, then press PTT button (on radio or headset accessory). Once the PTT button is released the radio will go back into scanning after 4 seconds of inactivity.
6. To exit Scan Mode, the user will Long Press (≥ 3 seconds) the Scan
Button. The radio will emit a single beep, alerting the user that the radio has exited the Scan Mode.
6 | BR02 instruction guide

Squelch

The Squelch function suppresses noises on free channels and allows to receive even weak signals. BR02 PRO has 10 dierent Squelch levels that can be set by program­ming software: 0 means that the Squelch is turned o; from level 1 to level 9 you will have dierent levels of noise reduction. The higher is the level, the louder will be the Squelch. By default, the Squelch level of BR02 PRO is set on level 4.
Make sure you do not set an excessively high squelch level because in this case you may not be able to receive weaker signals. On the other hand an exces­sively low Squelch value could enable the Squelch even when no signals are present. Squelch must always be adjusted when no signals are present.
The Time Out timer is settable from 30 sec to 270 sec. only through the programming software. This feature is disabled by default.

Battery recharge

BR02 PRO is equipped for using a 3,7V Li-ion rechargeable battery pack
which can be recharged connecting the socket of the AC/DC wall adaptor to a mains power socket and inserting the jack of the wall adaptor into the desktop charger plug. It takes 4-5 hours to fully recharge the radio. For maximum battery life, we recommend charging the battery pack when the BR02 PRO is o and the battery pack is fully discharged.
! Using a dierent battery charger other than the one specified can cause
damage to your device or may even cause explosions and personal injuries.
The Battery power saving feature enables a reduction in consumption of up to 50%. If it has been set, it automatically activates when the transcei­ver does not receive any signal for more than 5 seconds in order to save the battery life. Power saving can be disabled only through Programming software.
BR02 instruction guide | 7

Maintenance

Your BR02 PRO was designed to fulfill any warranty obligations and to enjoy this product for many years. As for all the electronically devices, we recommend you to follow this few suggestions:
• Do not attempt to open the unit. Non-expert handling of the unit may
damage it and/or annul the warranty.
• High temperatures can shorten the life of electronic devices, and warp
or melt certain plastics. Do not store the radio in dusty or dirty areas.
• Keep the Radio dry. Rainwater or damp will corrode electronic circuits.
• If it appears that the Radio diuses peculiar smell or smoke, please shut
o its power immediately and take o the charger or battery from the Radio.
• Do not transmit without antenna.
8 | BR02 instruction guide
Technical specifications
General
Frequency range 446.00625- 446.09375 MHz
(PMR446) Working temperature -20°/+55° C Operating voltage 3.7 V Operate mode Simplex Dimensions 56 x x118 x x33 mm (without antenna) Weight 180 g (Battery pack included) Antenna impedance 50Ω Duty cycle 5/5/90% Category B
Transmitter
Frequency stability ±2.5PPM Output power ≤500mW ERP Max frequency deviation ≤2,5KHz Audio distortion ≤3% Adjacent channel power < 60 dB Spurious radiation Within European legal terms Occupied bandwidth Within European legal terms
Receiver
RF sensibility <0.2UV@20 dB SINAD Audio distortion ≤3% Audio response 300Hz ÷ 3KHz Adjacent channel selectivity Within European legal terms Intermodulation rejection Within European legal terms Spurious response Within European legal terms Blocking Within European legal terms
WARNING: Direct plug-in ac/dc power supply must be used for disconnecting the transceiver from
the mains; the desktop charger must be positioned close to the unit and easily accessible.
BR02 instruction guide | 9
Troubleshooting
Problem Possible Cause Solution
The radio doesn’t switch on
The radio switches o shortly after it has been switched on
The battery pack does not recharge
The radio switches on but is unable to receive signals
The battery pack is discharged and/or has not been installed correctly.
Discharged battery pack. Recharge the battery pack.
The battery-charger has not been connected or instal- led correctly.
The site of installation is too shielded. Move to an another area.
The volume is too low Adjust the volume level.
Incorrect CTCSS or DCS
An incorrect radio channel has been selected.
It is not possible to communicate with other parties
Reception is fragmented and/or disturbed
The autonomy of the battery pack is limited Commission time is too high.
10 | BR02 instruction guide
The radio is installed in a shielded area or is too far from the party you are communicating with
Incorrect CTCSS or DCS
The signal is very weak.
The transmission distance is excessive and/or there are obstacles in the transmission path
Other parties are using the same channel
The radio has been installed too close to equipment that causes interference (televisions, computers, etc.)
Verify that the battery pack is charged and that it has been correctly installed.
Inspect the connections of the battery-charger and the installation of the batteries.
Move to an another area.
Check that the CTCSS tone or DCS code corresponds to the one set by the parties you are communicating with.
Select the same radio channel used by the parties you are communicating with.
Move to another area.
Check that the CTCSS tone or DCS code corresponds to the one set by the parties you are communicating with.
Try temporarily disabling the Squelch by means of the Monitor feature.
Move closer to the party you are communicating with or to another area.
Check the trac on the radio channel by means of the Monitor feature and select another channel if required.
Increase the distance between the radio and this equipment.
Try reducing the transmission time and/or using a low power.
BR02 instruction guide | 11
Prodotto o importato da:
MIDLAND EUROPE S.r.l.
Via. R.Sevardi 7- 42124 Reggio Emilia Italia
www.midlandreurope.com
In Italia l’uso di questo apparato è soggetto ad una dichiarazione. Prima dell’uso leggere attentamente le istruzioni. Se il prodotto contiene batterie: non gettare nel fuoco, non disperdere nell’ambiente dopo l’uso, usare gli appositi contenitori per la raccolta.
Produced or imported by:
MIDLAND EUROPE S.r.l.
Via. R.Sevardi 7 42124 Mancasale Reggio Emilia Italy
Imported by:
ALAN - NEVADA UK
Unit 1 Fitzherbert Spur Farlington Portsmouth Hants. P06 1TT - United Kingdom
www.nevada.co.uk
The use of this transceiver can be subject to national restrictions. Read the instructions carefully before installation and use. If the product contains batteries: do not throw the battery into fire. To disperse after use, throw into the appropriate containers.
Importado por:
MIDLAND IBERIA, SA
C/Cobalt, 48 - 08940 Cornellà de Llobregat (Barcelona - España)
www.midland.es
El uso de este equipo puede estar sujeto a la obtención de la correspondiente autorización administrativa. Lea atentamente las instrucciones antes de usar el equipo. si el producto contiene pilas o baterías no las tire al fuego ni las disperse en el ambiente después de su uso, utilice los contenedores apropiados para su reciclaje.
Vertrieb durch:
ALAN ELECTRONICS GmbH
Daimlerstraße 1g - D-63303 Dreieich Deutschland
www.alan-electronics.de
Die Benutzung dieses Handfunkgerätes ist von den landesspezifischen Bestimmungen abhängig. Vor Benutzung Bedienungsanleitung beachten. Bei Verwendung von Batterien beachten Sie bitte die Umweltbestimmungen. Batterien niemals ins oene Feuer werfen, und nur in dafür vorgesehene Sam­melbehälter entsorgen.
Loading...