Page 1
MODEL：
MA100W75 Series
MA100W85 Series
MA100W95 Series
Page 2
CONTENTS
SAFETY INSTRUCTIONS
Safety instructions .................................. ............ ... ..... . .
INSTALLATION
Product description .............................................. .....
Installation area ......................................... ........ ........... ..
Unpacking the washing machine ...................
Levelling the washing machine ..........................
Selection of tap ................................................... . .......... .
Connection of inlet hose, tap and washing machine...
OPERATIONS
Preparation before washing...................................
Washing .......................................................... . .......... ............
After washing................................................. ....................
Washing matters needing attention .............
The usage of detergent and washing powder.............
Control panel ................................................... ..................
Option...................................................... ...... ........................ ...
Personalized setting of washing program.........
Operations of washing process..........................
Washing program table .............................. ..............
MAINTENANCE
Cleaning and care ....................................... ....... .......... .
Cleaning the cabinet............................................ ........
Cleaning drain pump filter .....................................
Troubleshooting.......................................... ........... ....... ..
Technical information ...................................... ...........
Energy efficiency test program.........................
2
8
9
9
10
1 1
1 1
12
12
12
13
13
14
15
16
16
17
18
18
19
20
2 1
22
1
Page 3
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
For your safety, the information in this manual must be followed
to minimize the risk of fire or explosion, electric shock, or to
prevent property damage, personal injury or loss of life.
• This appliance is not intended for use by persons(including
children) with reduced physical, sensory or mental capabilities
or lack of experience and knowledge unless they have
been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
•
play with the appliance.
If the supply cord is damaged, it must be replaced by the
•
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
The new hose-sets supplied with the appliance are to be
•
used and that old hose-sets should not be reused.
• The openings must not be obstructed by a carpet.
• This appliance is intended to be used in household and similar
applications such as:
- staff kitchen areas in shops, offices and other working environments;
- farm houses;
- by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments;
- areas for communal use in blocks of flats or in launderettes.
2
Page 4
MA100W75 Series
MA100W85 Series
MA100W95 Series
Page 5
SAFETY INSTRUCTIONS
Warning!
The electric shock!
This appliance is for indoor use only.
•
Do not put washing machine at humid place.
•
• Hands shall not be inserted into running spin-dry tub .
• If the spin-dry tub does not stop within 15 seconds after
opening the cover , please stop using the machine and
have it repaired.
• Before any maintenance the device, unplug the appliance
from the mains.
• Always unplug the machine and turn off the water supply
after use. The max. inlet water pressure, in pascals. The
min. inlet water pressure, in pascals.
• To ensure your safety, power plug must be inserted into
an earthed three-pole socket. Check carefully and make sure
that your socket is properly and reliably earthed.
• Make sure that the water and electrical devices must be
connected by a qualified technician in accordance with the
manufacturer's instructions and local safety regulations.
4
Page 6
SAFETY INSTRUCTIONS
Risk to children!
• EN countries: the appliance can be used by children aged
from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
• Animals and children may climb into the machine. Check
the machine before every operation.
• Young children should be supervised that they do not play
with the appliance.
• Machine may be very hot during the operation. Keep kids
and pets far away from the machine during the operation
very wet rooms as well as in the rooms with explosive or
caustic gas.
•
Remove all packages before using the appliance. Otherwise,
serious damage may result.
• The washing machine with single inlet valve only can be
connected to the cold water supply. The product
inlet valves should be correctly connected to the hot water
and cold water supply.
• Plug must be accessible after installation.
with double
Risk of explosion!
•
Do not wash or dry articles that have been cleaned in, washed
in, soaked in, or dabbed with combustible or explosive
substances( such as wax, oil, paint, gasoline, degreasers,
dry-cleaning solvents, kerosene, etc.) This may result in
fire or explosion.
Before hand thoroughly rinse items of washing by hand.
•
5
Page 7
SAFETY INSTRUCTIONS
Caution
Installing the product!
• This washing machine is for indoor use only.
• It isn't intended to be built-in using.
• The openings must not be obstructed by a carpet.
• Washing machine shall not be installed in bath room or
very wet rooms as well as in the rooms with explosive
or caustic gases.
• Remove all packages and transport bolts before using
the appliance. Otherwise, serious damage may result.
• The washing machine with single inlet valve only can be
connected to the cold water supply. The product with
double inlet valves should be correctly connected to the
hot water and cold water supply.
• Plug must be accessible after installation.
Risk of damaging appliance!
• Your product is only for home use and is only designed
for the textiles suitable for machine washing.
• Do not climb up and sit on top cover of the machine.
• Do not lean against machine door.
• Cautions during Handling Machine:
1.Transport bolts shall be reinstalled to the machine by
a specialized person.
2.The accumulated water shall be drained out of the
machine.
3.Handle the machine carefully. Never hold each protruded
part on the machine while lifting. Machine door can
not be used as the handle during the conveyance.
4.This appliance is heavy. Transport with care.
6
Page 8
SAFETY INSTRUCTIONS
• Please do not close the door with excessive forces.
• It is forbidden to wash carpets.
Operating the appliance!
• Before washing the clothes at first time, the product
shall be operated in one round of the whole procedures
without the clothes inside.
• Flammable and explosive or toxic solvents are forbidden.
Gasoline and alcohol etc.Shall not be used as detergents.
Please only select the detergents suitable for machine
washing, especially for drum.
• Make sure that all pockets are emptied. Sharp and rigid
items such as coin, brooch, nail, screw or stone etc. may
cause serious damages to this machine.
• Please check whether the water inside the drum has
been drained before opening its door.Please do not open
the door if there is any water visible.
• Be careful of burning when the product drains hot
washing water.
• Never refill the water by hand during washing.
• After the program is completed, Please wait for two
minutes to open the door.
Packaging/Old appliance
This marking indicates that this product should not be disposed
with other household wastes throughout the EU.To prevent
possible harm to the environment or human health from
uncontrolled waste disposal,recycle it responsibly to promote
the sustainable reuse of material resources.To return your used
device,please use the collection systems or contact the retailer
where the product was purchased. They return and can take this
product for environmental safe recycling.
7
Page 9
INSTALLATION
Product description
Top lid
Frame
Control pa nel
Cabi net
Adjustable foot knob
Drain hose
Water inlet valve
Power case and plug
Handle
Or
Note!
• The product line chart is for reference only, please refer to real product as
standard.
Accessories
Inlet hose a ss
cabinet ba se bo ard
manual
screw
Note!
• Note: if the drain hose is already installed on the machine, then there is no
spring clamper and drain hose in the accessories.
8
spring clamper
drain loose ass
Or
Page 10
INSTALLATION
Installation area
Warning!
•
Stability is important to prevent the product from
wandering!
•
Make sure that the product should not stand on
the power cord.
Before installing the machine, the location characterized
as
follows shall be selected:
1.Rigid, dry, and level surface
2.Avoid direct sunlight
3.Sufficient ventilation
4.Room temperature is above 0 C
5.Keep far away from the heat resources such as coal or gas.
Unpacking the washing machine
Warning!
Packaging material (e.g. Films, Styrofoam) can be
•
dangerous for children.
There is a risk of suffocation ! Keep all packaging
•
well away from children.
w
W> 20mm
w
1. Remove the cardboard box and styrofoam packing.
2. Lift the washing machine and remove the base packing.
3. Remove the tape securing the power supply cord and
drain hose.
4. Remove the inlet hose from the drum.
The installation of drain hose
hose
Drain inserted
into the drain
Clamping spring
9
Page 11
INSTALLATION
Warning!
Do not kink or protract the drain hose.
•
• Position drain hose properly ,otherwise damage might result of water leakage.
• If drain hose is too long, do not force it into washing machine as it will cause
abnormal noises.
There are two ways to place the end of drain hose:
1.For lower drain system
Under3m
Under 15cm
2.For upper drain system
Trough
Hose
Retainer
nd
Bi
Max.1 00cm
Min. 86cm
Levelling the washing machine
Warning!
• The lock nuts on all four feet must be screwed tightly against the housing.
1.Check if the legs are closely attached
the cabinet. If not, p lease turn them to
their original positions tighten the nuts.
2.Check ali gnment of the produ ct with a
spirit level and if required, correct.
3.Loosen the l ock n ut an d tur n the feet
until it closely contacts with
the floor.
4.After being locked properly, press four
corners again to make sure that they has
been adjusted properly.
to
Lock nut
loos en
Rais e
foot
lock
Lower
wrong
righ t
water
trough
m
6c
n.8
Mi
m
0c
0
1
.
x
Ma
10
9
Page 12
INSTALLATION
Selection of tap
Please s e lect
tap.
appropriate
Ordinary faucet
Screw tap
Spec ial washing
mach ine tap
Connection of inlet hose, tap and washing machine
1:Connection between ordinary tap and inlet hose.
Wall
tap
clam p nut
1.Loosen clam p nut to
show 5mm threa d
slid e bushing
5.Press sl ide bushi ng,
inse rt inlet hose into
connec ting base
2:connection between screw tap and inlet hose.
2.Loosen four bol ts
6.connec tion fini shed
3.Set connecting base
on tap an d t ighten
bolt s evenly
inle t hose
7.After connectio n and installation,
chec k if there is water leakage
4.Tighten cl amp nut
inle t valve
tap wi th threads an d inlet hos e
spec ial tap for washing machine
Warning!
• To prevent leakage or water damage, follow the instructions in this chapter
Do not kink, crush, modify or sever .
• water inlet hose
10
11
!
Page 13
OPERATIONS
Preparation before washing
Caution!
•
Before washing, please make sure it’s installed properly.
•
Before washing it at first time, the washing machine shall be operated in one
round
of the whole procedures without clothes in as follows.
1 2 3 4
Plug in
Open tap
Load and Close door
Add detergent
Washing
1 2
Power On
Select Programme
Select Level
Note!
• , If default is selected, step 2 3 can be skipped.
3 4
Start up
After washing
Buzzer will beep after washing finished and the power supply will be cut off automatically
Then unload the laundry.
.
10
12
Page 14
OPERATIONS
• The working condition of the washer should be(0-40)℃.If used under 0℃,the inlet
valve and draining system may be damaged. If the machine is placed under condition
of 0℃or less, then it should be transferred to normal ambient temperature to ensure
the water supply hose and drain hose are not frozen before use.
• Please check the labels and the explanation of using detergent before wash. Use
non-foaming or less-foaming detergent s uitable for machine washing prop erly.
Washing matters needing attention
Check the label
Put small clothes into the
pillow slip
alarm due to great unbalance. Therefore it is suggested to add one or two
more clothes to be washed together so that draining can be done smoothly.
• Don’t washing the clothes touching with kerosene, gasoline, alcohol and
other flammable materials.
• As for the agglomerated or ropy detergent or additive, before they are
poured the detergent box, it is suggested to use some water for
dilution to prevent inlet of detergent box from being blocked and
overflowing while filling water.
•
temperature to get the best washing performance with less water and
energy consumption.
Warning!
• When washing a single clothes, it may easily cause great eccentricity and give
The usage of detergent and washing powder
into
Please choose suitable type of detergent for the various washing
Take out the items o ut of
the po ckets
Turn easy-pilling and
long-pile fabric inside out
the
Knot the long strips,zip or
button
Separate clothes with
different textures
10
13
Page 15
OPERATIONS
Control panel
End
33
5
4
2
Note!
The chart is for reference only, Please refer to real product as standard.•
1
On/Off
1
Product is switched on or off.
3
Program
Available according to the laundry type.
5
Display
The display shows the settings, estimated time remaining, options, and status messages
for your washer. The display will remain on through the cycle.
When LED fla sh in g it m ea ns t he t im e th at delay to star t the ma chine. When LED lighting it means
the program t im e th at remaining
, ,
.
2
Start/Pause
1
Press the button to start or pause the
washing cycle.
4
Option
This allows you to select an additional
function and will light when selected.
1
14
10
Page 16
OPERATIONS
Option
Only for washers having these function.
Water level
sele ct water level according to clothing catego ries, degre e of soilin g and washing
habi ts of custome rs
Delay
1. Select a program
2.Press the Delay button to choose the time
3.Press [Start/Pause] to commence the delay operation
Delay
On
Press the [Delay] button until the Delay light is off .
starting the program. If the program already started, should press the [On/Off]
button to reset the program.
Choose the Program
Setting time
It should be pressed before
Caution!
• . If there is any break in the power supply while the machine is operating, a
special memory stores the selected program and when the power is restarted
Start
15
Page 17
OPERATIONS
Personalized setting of washing program
Customers can select wa shing program according to actual demand, and set water
volume and appoi ntment time
Program
Water Level
Delay
Operations of washing process
One Touch Smart Wash
On Start
Spin only
On
keep pressing key untilProgram
disply
Note!
Note: ot her process combina tions are just li ke above.
Program
StartOn
Start
16
Page 18
OPERATIONS
Washing program table
Program are available according to the laundry type.
Only for was hers having t hese func tion
Program
Quick
Soft:
Normal
Hygiene
Soak
Spin only
Suitable to wash light stained clothes and clothes in summer.
the tempo is soft, slow washing and spinning speed, to make the lightest
wear and deformation.
Standard fabric washing program, suitable to wash ramie cotton fabric.
Wash for once, rinsing for twice, the spin time is a little long.
This program is able to effectively remove mites in clothes.
Select this program if .clothes need to be soaked before washing
Select this program .to Spin and drain only
10
17
Page 19
MAINTENANCE
Cleaning and care
Warning!
• Before your maintenance starts, please unplug the machine and close the tap.
Cleaning the cabinet
Proper maintenance on the washing machine can extend its
working life. The surface can be cleaned with diluted
non-abrasive neutral detergents when necessary. If there is
any water overflow, use the wet cloth to wipe it off immediately.
No sharp items are allowed.
Note!
Formic acid and its diluted solvents or equivalent are forbidden, such as
•
solvents or chemical products,etc.
alcohol,
Cleaning the inlet filter
Note!
• Inlet filter must be cleaned if there is less water.
Washing the filte r in wash ing machine:
1.S crew off the inlet pipe fro m the backs ide
of the m achine.
2.Pull out the filter with long nose pliers
and reinsta ll it back after being washed.
the brush
3.Use to clean the filte r.
4.Reconnect the inlet pipe.
Lint filter clean
1.There is a built-in lint filter in your washer. It
can help to collect lint during washing cycle.
2.It is suggested to clean the lint filter every
10 cycles.
3.Take it out and clean the filter with water.
Then place it back into the washer.
10
18
magic filter
normal filter
Page 20
MAINTENANCE
Cleaning drain pump filter
Only for washers having these function.
Warning!
Be careful of the hot water!
•
Allow detergent solution to cool down.
•
• Unplug the machine to avoid electrical shock before washing.
• Drain pump filter can filter the yarns and small foreign matters from the
washing.
• Clean the filter periodically to ensure the normal operation of washing
machine.
1
Drain the water out of the
pump, under which use a
container to collect.
4
Clean the filter.
Open the filter by turning
to the counter clockwise
Restore it and adjust the convex
place to align at the pump hole.
2
Remove extraneous matter
5
Tighten the pump
cover clockwise.
Caution!
• Make sure that valve cap and emergency drain hose are reinstalled properly, cap
plates should be inserted aligning to hole plates otherwise water may leak;
• When the appliance is in use and depending on the program selected there can
be hot water in the pump. Never remove the pump cover during a wash cycle, always
wait until the appliance has finished the cycle, and is empty. When replacing the
cover, ensure it is securely re-tightened.
3
6
19
10
Page 21
MAINTENANCE
Trouble shooting
The start of the appliance does not work or it stops during operation.
First try to find a solution to the problem, If not, contact the service centre.
Description
No washing
No water flows in
Abnormal draining
Abnormal spin
Description
E1
E2
E3
E4
Inspection Items
If the power is off or the fuse is burned out.
If the power supply voltage is too low.
If the water amount reaches to the required water level.(The washer will
not work if the water amount does not reach the required water level)
If it is set to "Delay" washing mode. (It will only start to work until the
reservation time reached)
If the power is off or the fuse is burned out.
If the water supply is cut off or the water pressure is too low.
If the inlet hose is properly connected and the water tap is opened.
If the filtering screen of inlet valve is blocked by dirt.
If the coil of inlet valve is damaged. (The slight electromagnetic sound is
normal phenomenon when the inlet valve is switched on)
If the "Start / Pause" button is pressed after the power switch is pressed.
If the water drain hose is placed very high.
If the end of water drain hose is sealed in pond.
If the internal rubber ring of drain valve is blocked by dirt.
If the door lid is closed.
If all clothing piled largely at one side of barrel or the clothing is excessively
placed.
If the washer is not placed in stable condition or it is placed in inclination
state. (The ground is not flat).
If the motor belt is loosened.
Reason
Alarm for abnormal
water intaking.
Alarm for water drain
has not finished.
Alarm for lid not closed
before wash and spin.
Alarm for washing stay
at one side.
Check the water tap is
opened or not.
Check the water level
sensor and drain pump.
Close the lid, Press "Start" button
Manually balance clothes
in the barrel by hands.
Solution
EXX
Others
Please try again first, call up service
line if there are still troubles
Note!
• or the display
After the check, activate the appliance. If the problem occurs
shows other alarm codes
again, contact the service.
10
20
Page 22
MA100W75 Series
MA100W85 Series
MA100W95 Series
Page 23
MAINTENANCE
Energy efficiency test program:
Entry mode of energy efficiency p rogram in Malaysia
Press the “O N/OFF” button
1:
2:Press th e “pro gram” button, to select the” N ormal ”program (displ ay P1), and press
the water level key to set the level 8 (display L8)
3:Press th e “s tart “button to sta rt the operatio n
Entry mode of water co nsumption procedure in Singapore
1:
Press the “O N/OFF” button
2:Press th e “pro gram” button, to select the ”Q uick” program (display P2),
3:Press th e “s tart “button to sta rt the operatio n
Note!
• Do not operate operations not mentioned in the above steps
102410
22
Page 24
QU ESTIONS O R CO MMENTS
Country
Contact C en ter
Web S ite
Tha il an d
Mya nm ar
Cambodi a
Vie tn am
Philipp in es
Indones ia n
Malaysia
Singapo re
+662107779 9
+0926 03 672 29
+8552 32 124 35
+180058 88 63
+6328 86 35522
+628001 88 8523
+6039 22 11033
+622225 36
Th is p ro du ct i s Ro HS c om pl iant.
http://www.m idea.com/t h
https://www.gbs.com.mm /en/abo ut /vsk/
http://blu em idea.com
http;//vn.m id ea .co m
http://www.m ideaph. com
http://id. mi dea.c om
https://www. midea.com/my/
https://www. midea.com/s g/
Page 25
V1.0
1613 8000A 38905
Loading...