Midas Consoles V190 PSU User Manual

OPERATORS MANUAL

Midas,

Klark Teknik Building,

Walter Nash Road,

Kidderminster.

Worcestershire.

DY11 7HJ.

England.

Tel:[phone]

Fax:[phone]

Email: [e-mail]

Website: www.midasconsoles.com

MIDAS Verona Power Supply

DOC02-V190

(c) Telex Communications (UK) Ltd.

In line with the company’s policy of continual improvement, specifications and function may be

subject to change without notice. This Operators Manual was correct at the time of writing. E&OE.

Issue 1.0 - February 2004

Operators Manual

Important Safety InstructionsImportant Safety Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

AVIS: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR

These symbols are internationally accepted symbols that warn of potential hazards with
electrical products.

The lightning flash with arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturers
instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.

11. Only use attachments / accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified personnel. Servicing is required when the apparatus is damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.

IEC-60065-Edn7-Midas

Klark Teknik Group (UK) Plc, Klark Teknik Building, Walter Nash Road,
Kidderminster. Worcs. DY11 7HJ. England
Tel:[phone] Fax:[phone]
www.midasconsoles.com www.klarkteknik.com

DECLARATION OF CONFORMITY

We,

Klark Teknik Group (UK) Plc

of, Klark Teknik Building, Walter Nash Road, Kidderminster, Worcestershire, DY11 7HJ.

Declare that a sample of the following product:-

Product Type Number Product Description Nominal Voltage (s) Current Freq

V190 External Linear 100V AC, 120V AC 4.3A, 3.7A 50/60Hz

Power Supply 220V AC, 240V AC 2.1A, 1.95A

to which this declaration refers, is in conformity with the following directives and/or standards:-

Directive(s) Test Standard(s)

Generic Standard using EN55103 Limits and Methods
Class B Conduct Emissions EN55103
Class B Radiated Emissions EN55103
Fast Transient Bursts EN61000-4-4
Static Discharge EN61000-4-2
Electrical Safety

EN60065:2002
UL60065-03

Pending

CAN/CSA60065-03
IEC60065-2001

Pending

Pending

Signed:............................ Date: 27th February, 2004

Name: Simon Harrison

Authority: Research and Development Director, Klark Teknik Group (UK) PLC

Attention!
Where applicable, the attention of the specifier, purchaser, installer or user is drawn to special limitations
of use which must be observed when these products are taken into service to maintain compliance with
the above directives. Details of these special measures and limitations to use are available on request
and are available in product manuals.

A Subsidiary of Telex Communications, Inc.

The V190 external power supply has been developed to be used soley with the Midas Verona Series of audio mixing
consoles.

All backed up by the standard Midas Three Year Warranty.

Please take the time to complete and return the registration card and, to obtain the best results with a minimum of
effort, also read this operators manual.

Contents

Installation and Service 1
Connection and Operation 2
Using Multiple Power Supplies 3
Specifications 4

Installation and ServiceInstallation and Service

The V190 series power supply unit is a two unit nineteen inch (2U 19”) rack mounted power supply for use with the Midas
Verona series of consoles only.

Installation

Before installing the power supply, please ensure that the correct mains supply voltage is selected on the rear of the supply.
The mains inlet is provided via a single IEC type socket. A mains cables is supplied with the unit. Never, under any
circumstances, should the power supply be operated without it’s safety earth connection.

The V190 series power supply should be installed into a 19” rackmount enclosure. If the power supplies are not in a
permanent installation, the rackmount enclosure construction should take into account the weight of the supply to prevent
damage to either the power supply or enclosure while in transit.

Air Flow

The V190 power supply has a forced air cooling channel flowing from back to front. To maintain adequate ventilation to the
unit, the cooling channel must not be blocked or hindered and one unit (1U) should be left free between the top of the
power supply and any other equipment or the rack. The rackmount enclosure should allow adequate airflow to both the
front and back panels of the power supply.

If using a number of power supplies, one unit (1U) space should be left free above each supply.

0

PUSHPUSH

I

Front

Rear

Power

DC Output / Link

Pin1-

0VA

+

1

Pin2-

_

Pin3-

1

+

Pin4-

1

+

Pin5-

48V

Pin6-

0VL

Shell -

Chassis

8V
8V
2V

DC Output / Link

+

+

Low

48V

2V

Mains

PUSH

1

WARNING:

DONOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

AVIS:

NOUSER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIEDSERVICE PERSONNEL.

CAUTION:

FIREREPLACE WITH THE SAME TYPE AND VALUE FUSE INDICATED.

ATTENTION:

COMMEINDIQUÉ.

THISDEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING CONDITIONS:
(1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2)THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Interference

Some interference may be noticed when the power supply is situated in close proximity to the Verona console. Moving the
power supply away from the console will rectify this problem.

DC Output / Link

_

+

8V

8V

1

1

CAUTION

RISKOF ELECTRIC SHOCK

DONOT OPEN

TOREDUCE THE RISK OF ELECTRIC SHOCK,

RISQUEDE CHOC ELECTRIQUE. NE PAS OUVRIR.

FORCONTINUED PROTECTION AGAINST RISK OF

REMPLACERPAR UN FUSIBLE DE MÊME TYPE

MADE IN KIDDERMINSTER,ENGLAND

SUPPLY
VOLTAGE

100V/120V/220V/240V

~

AC

50-60Hz520W

FUSE:5x20mm
T5A L250V

CHECK VOLTAGESELECTOR

BEFORE APPLYING MAINS.

Service

The power supply may only be serviced by authorised personnel. Refer all servicing to a qualified, approved Midas service
agent.

Depending upon where the power supply is installed, the interior of the unit will become, over time, dirty and will require
cleaning.

The power supply should also be serviced if it is dropped, exposed to rain or moisture, liquid has been spilled into the supply
or if the unit ceases to function normally.

DO NOT REMOVE THE COVER

The inside of the power supply contains potentially lethal voltages and is capable of providing high currents. To reduce

the possibility of electric shock, do not open the cover to the power supply. High voltages are still present in the

supply, even when isolated from the mains.

Operators Manual - 1Page

Connection and OperationConnection and Operation

Connection

Before powering up the V190 power supply, connect either the front or rear power supply output to the power inlet socket
on the console.

The V190 power supply provides:

+12 volts
±

18 volts

+ 48 volts

Pin1­Pin2­Pin3­Pin4­Pin5­Pin6-

0VA

+

8V

1

_

8V

1

+

2V

1

+

48V
0VL

DC Output / Link

PUSH

The power supply should only be connected to the console using the provided power connection cable. If, for any reason,
the power connection cable should become damaged, the cable should be serviced by an authorised Midas service agent
immediately or a Midas authorised replacement sought.

WARNING:

The V190 power supply is capable of providing high currents. A short-circuit on any of the voltage supply pins
of the power supply or connector will cause a high current to flow from the supply which could lead to damage both to the
supply and to connected equipment and also a risk of fire and severe burns to persons.

The V190 power supply should be connected to the mains with the supplied IEC mains leads.

220VAC

The V190 is a Linear power supply capable of operation where the nominal mains voltage is 100, 120,
220 or 240 VAC (50-60Hz). The correct mains supply voltage must be selected before applying mains
power to the unit.

To change the mains operation voltage, disconnect from the mains. Open the compartment above the
mains inlet connector with a flat bladed screw driver. Once open, you will see a drum with an operating
voltages printed on each face. Remove the drum, then turn the drum to the required voltage and return

o the holder. Press firmly and then close the compartment. Make sure that the correct voltage now

it t
appears in the window of the compartment.

The Midas V190 power supply MUST be earthed. The power supply should NEVER be used with the earth connection

NOTE:

removed. The mains inlet socket earth connection is a safety connection and should be connected to the mains earth
through the earth conductor in the provided mains lead.

WARNING:

To prevent the risk of fire, fuses should always be replaced with fuses of the same rating and type.

Operation

After connecting the V190 power supply to the console, switch on the power supply using the rocker switches on the front
panel. Power will be applied to the console.

The user may monitor the activity of each of the voltage rails using the LEDs on the front panel. Each LED will light to show
the rail is active. In addition, a Low Mains indicator is provided to alert the user to a mains undervoltage condition.

0

Where multiple supplies are present, these should be switched on at the same time so that excessive
load is not applied to any single supply. Power supply linking information is shown on the next page.

I

+

48V

Power

Low

Mains

The internal operating temperature of the power supply could be sufficient to cause burns to persons. Do not open the

cover or attempt to remove or bypass the safety covers protecting the fan and cooling channel.

_

+

2V

1

+

8V

8V

1

1

WARNING: HOT

Operators Manual - 2Page

Using Multiple Power SuppliesUsing Multiple Power Supplies

Using Multiple Power Supplies

The number of power supplies shipped as standard with the Verona varies with the frame size as follows:

Channels Internal External

24 - 32 1 0
40 - 56 2 0
64 2 1

Where multiple supplies are present, these should be switched on at the same time so that excessive load is not applied to
any single supply.

The external power supply can be used on 24-56 channel frame sizes to add redundancy or replace the internal supplies.
Two external supplies would be required to replace the internal supplies of the 56 channel console and retain redundancy.
The external supply has a “daisy chain” facility (as shown below) allowing for a number of power supplies to be used
together adding redundancy to the system in the event of a power supply failing.

Connection 6 Pin Male XLR

Pin 1 0V Analogue
Pin 2 +18V Analogue
Pin 3 -18V Analogue
Pin 4 +12V Gooseneck Light
Pin 5 +48V Phantom
Pin 6 0V Gooseneck Light
Case Chassis

Under NO circumstances should the Venice series power supply be used with the Verona.
Only the MidasV190 Linear External Power Supply is approved for use with Verona consoles.

to console

0
I

Power

0

I

Power

+

Low

48V

Mains

+

Low

48V

Mains

PUSHPUSH

DCOutput / Link

_

+

+

8V

8V

1

1

2V

1

PUSHPUSH

DCOutput / Link

_

+

+

8V

8V

1

1

2V

1

to subsequent supplies

Servicing and Maintenance

DCOutput / Link

Pin1­Pin2­Pin3­Pin4­Pin5­Pin6­Shell -

DCOutput / Link

Pin1­Pin2­Pin3­Pin4­Pin5­Pin6­Shell -

CAUTION

RISKOF ELECTRIC SHOCK

DONOTOPEN

TOREDUCETHE RISK OF ELECTRIC SHOCK,

WARNING:

DONOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

PUSH

AVIS:

0VA

+

8V

1

_

8V
1

+

2V
1

+

48V
0VL

Chassis

0VA

+

8V

1

_

8V
1

+

2V
1

+

48V
0VL

Chassis

RISQUEDE CHOC ELECTRIQUE.NE PAS OUVRIR.

NOUSER SERVICEABLE PARTSINSIDE. REFER SERVICING TO
QUALIFIEDSERVICE PERSONNEL.

CAUTION:

FIREREPLACE WITH THE SAME TYPE AND VALUEFUSE INDICATED.

ATTENTION:

COMMEINDIQUÉ.

DCOutput / Link

THISDEVICECOMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING CONDITIONS:
(1)THISDEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2)THISDEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

WARNING:

DONOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

PUSH

AVIS:

RISQUEDE CHOC ELECTRIQUE.NE PAS OUVRIR.

NOUSER SERVICEABLE PARTSINSIDE. REFER SERVICING TO
QUALIFIEDSERVICE PERSONNEL.

CAUTION:

FIREREPLACE WITH THE SAME TYPE AND VALUEFUSE INDICATED.

ATTENTION:

COMMEINDIQUÉ.

DCOutput / Link

THISDEVICECOMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING CONDITIONS:
(1)THISDEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2)THISDEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

FORCONTINUED PROTECTIONAGAINST RISK OF

REMPLACERPARUN FUSIBLE DE MÊME TYPE

CAUTION

RISKOF ELECTRIC SHOCK

DONOTOPEN

TOREDUCETHE RISK OF ELECTRIC SHOCK,

FORCONTINUED PROTECTIONAGAINST RISK OF

REMPLACERPARUN FUSIBLE DE MÊME TYPE

MADEIN KIDDERMINSTER, ENGLAND

MADEIN KIDDERMINSTER, ENGLAND

SUPPLY
VOLTAGE

100V/120V/220V/240V

~

AC

50-60Hz520W

FUSE:5x20mm
T5AL250V

SUPPLY
VOLTAGE

100V/120V/220V/240V

~

AC

50-60Hz520W

FUSE:5x20mm
T5AL250V

CHECKVOLTAGE SELECTOR

BEFOREAPPLYING MAINS.

CHECKVOLTAGE SELECTOR

BEFOREAPPLYING MAINS.

Both the Verona and the Midas V190 linear external power supply both contain potentially lethal voltages and should only
be serviced by authorised Midas service agents. In the event of malfunction, please refer servicing to qualified personnel.
Contact your Midas dealer for more information.

Operators Manual - 3Page

Technical Specification

Specifications

Mains inlet

Mains Voltage Supply

Mains Voltage Ranges 100VAC = 85-110VAC

Mains Input Current

Input Power

Output Power

Output

Operating
Temperature

Dimensions

Height 2U (86mm / 3.385”)
Width 19” Rackmount (482mm / 19”)
Depth 350 mm / 13.78”

IEC

100 - 240V AC Selectable

120VAC = 102-132VAC
220

VAC = 187-242VAC

240VAC = 204-264VAC

100VAC = 4.3A
120VAC = 3.7A
220VAC = 2.1A
240VAC = 1.95A

520W (Max)

190W (Max)

+18V = 4A (Max)

-18V = 4A (Max)
+12V = 2A (Max)
+48V = 400mA (Max)

o

0-40 C

(Max)
(Max)
(Max)

(Max)

Weight

Connection

Pin 1 0V Analogue
Pin 2 +18V Analogue
Pin 3 -18V Analogue
Pin 4 +12V Gooseneck Light
Pin 5 +48V Phantom
Pin 6 0V Gooseneck Light
Case Chassis

13.0kg (28.6lbs)

6 Pin Male XLR

Operators Manual - 4Page