Midas Consoles PRO3-CC-IP, PRO3-CC-TP, PRO6-CC-IP, PRO6-CC-TP, PRO6-TP Operator Manual, English

...
PRO Series Live Audio Systems
Owner’s Manual
Midas Klark Teknik Limited,
Klark Industrial Park,
Walter Nash Road,
Kidderminster.
Worcestershire.
DY11 7HJ.
Tel: +44 1562 741515
Fax: +44 1562 745371
Email: info@midasklarkteknik.com Website: www.midasconsoles.com
PRO Series Live Audio Systems — Owner’s Manual
DOC02-PROSERIES Issue A — September 2010
In line with the company’s policy of continual improvement, specifications and function may be
subject to change without notice. This Owner’s Manual was correct at the time of writing. E&OE.
© Red Chip Company Ltd.
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with a dry cloth. 7 Do not block any of the ventilation
openings. Install in accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such
as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked
on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus.
11 Only use attachments/accessories
specified by the manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning
storms or when unused for long periods of time.
14 Refer all servicing to qualified personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15 Use the mains plug to disconnect the
apparatus from the mains.
16 Warning: To reduce the risk of fire or
electric shock, do not expose this apparatus to rain or moisture.
17 Warning: Do not expose this
equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the equipment.
18 Warning: The mains plug of the power
supply cord shall remain readily operable.
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES
Le symbole représentant un éclair fléché dans un triangle équilatéral a pour but d'alerter l'utilisateur de la présence d'une "tension dangereuse" non isolée à l'intérieur du boîtier, pouvant être d'une force suffisante pour constituer un risque d'électrocution.
Le point d'exclamation dans un triangle équilatéral a pour but d'alerter l'utilisateur de la présence d'instructions importantes concernant le fonctionnement et la maintenance, dans la documentation qui accompagne l'appareil.
1 Veuillez lire ces instructions. 2 Conservez ces instructions. 3 Respectez toutes les consignes de
sécurité.
4 Suivez scrupuleusement toutes les
instructions.
5 N'utilisez pas cet appareil près d'un point
d'eau.
6 Utilisez uniquement un chiffon sec pour le
nettoyer.
7 N'obstruez aucune des ouïes de
ventilation. Installez-le en respectant les instructions du fabricant.
8 Ne l'installez pas près de sources de
chaleur tels que radiateurs, panneaux chauffants, étuves, ou autres appareils produisant de la chaleur (dont les amplificateurs).
9 Ne pas utiliser d'adaptateur pour
supprimer la prise de terre des prises à trois fiches. Si la prise fournie ne peut pas être branchée dans la prise électrique, adressez-vous à un électricen qui remplacera la prise obsolète.
10 Protégez le cordon secteur afin que l'on ne
marche pas dessus et qu'il ne soit pas pincé, surtout au niveau des prises, ou à l'endroit où il sort de l'appareil.
11 Utilisez exclusivement des fixations et des
accessoires recommandés par le fabricant.
12 Utilisez l'appareil uniquement
avec le chariot, le trépied, le support ou la table spécifiés par le fabricant, ou vendus avec l'appareil. Si un chariot est utilisé, prenez toutes les précautions nécessaires lorsque vous devez déplacer l'ensemble (chariot et appareil) afin qu'ils ne se renversent pas.
13 Débranchez l'appareil en période d'orage
ou s'il doit rester inutilisé pendant longtemps.
14 Confiez toutes les réparations et
interventions à un personnel qualifié. Une intervention est nécessaire si l'appareil a été endommagé d'une façon ou d'une autre, si son cordon ou sa prise secteur ont été endommagés, si du liquide a été renversé ou si des objets sont tombés à l'intérieur, ou encore si l'appareil a été exposé à la pluie ou à l'humidité, s'il ne fonctionne pas normalement, ou s'il est tombé.
15 Débrancher l'appareil du réseau électrique
par la prise de secteur.
16 Avertissement : afin de réduire le
risque d'incendie ou de choc électrique, ne pas exposer cet appareil à la pluie ou à de l'humidité.
17 Avertissement : n'exposez pas cet
équipement aux éclaboussures et veillez à ce qu'aucun récipient rempli de liquide, verre ou vase, ne soit posé dessus.
18 Avertissement : la prise secteur doit
toujours rester directement accessible.
PRO6 EC-Declaration of Conformity
Midas
DOC04-PRO3ECDOC Rev. A
EC-Declaration of Conformity
The undersigned, representing the following manufacturer
Manufacturer: Address:
Midas Klark Teknik Ltd. Klark Industrial Park, Walter Nash Road, Kidderminster. Worcestershire. DY11 7HJ.
hereby declares that the following product
Product Type Number Product Description Nominal Voltage(s) Current Freq.
PRO3 Control Centre
115V AC 230V AC
2.9A
1.5A
50/60Hz
is in conformity with the regulations of the following marked EC-directives and bears the
-mark accordingly
reference number title
2004/108/EC EMC Directive (EMC)
2006/95/EC Low-Voltage Directive (LVD)
The conformity of the product with EC Directives for use in environment E4 is provided by compliance with the following standards:
Standards/date:
Applied Electrical Safety test standards:
reference number title
EN 60065:2002
Audio, video and similar electronic apparatus. Safety requirements.
Applied EMC emission test standards:
ref. no. title
EN 55103-1:1996 Class A
EN 55103-1 Annex A: Radiated magnetic disturbance, 50Hz-50kHz
CISPR 22: Radiated disturbance,
30-1000MHz
CISPR 22: Conducted disturbance,
ac & signal ports
CISPR 16: Discontinuous
disturbance
EN 61000-3-2:2000 Mains
harmonics
EN 61000-3-3:1995 Mains voltage
flicker
Applied EMC immunity test standards:
ref. no. title
EN 61000-4-2:1995 Electrostatic discharge
EN 55103-2:1996 Class A
EN 61000-4-3:1996: Radiated RF disturbance, 80-1000MHz
EN 55103-2 Annex A: Magnetic LF
disturbance, 50Hz–10kHz
EN 61000-4-4:1995: Fast transient
bursts, ac & signal ports
EN 61000-4-5:1995: Surge, ac port
EN 61000-4-6:1996: Conducted RF
field, ac & signal ports
EN 61000-4-11:1994: Mains voltage
dips and interruptions
Place, date: Kidderminster, UK 18th August 2010 General Manager AVP, Product Development Printed name: John Oakley Printed name: Alex Cooper
PRO6 EC-Declaration of Conformity
Midas
DOC04-PRO6ECDOC Rev. B
EC-Declaration of Conformity
The undersigned, representing the following manufacturer
Manufacturer: Address:
Midas Klark Teknik Ltd. Klark Industrial Park, Walter Nash Road, Kidderminster. Worcestershire. DY11 7HJ.
hereby declares that the following product
Product Type Number Product Description Nominal Voltage(s) Current Freq.
PRO6 Control Centre
115V AC 230V AC
2.9A
1.5A
50/60Hz
is in conformity with the regulations of the following marked EC-directives and bears the
-mark accordingly
reference number title
2004/108/EC EMC Directive (EMC)
2006/95/EC Low-Voltage Directive (LVD)
The conformity of the product with EC Directives for use in environment E4 is provided by compliance with the following standards:
Standards/date:
Applied Electrical Safety test standards:
reference number title
EN 60065:2002
Audio, video and similar electronic apparatus. Safety requirements.
Applied EMC emission test standards:
ref. no. title
EN 55103-1:1996 Class A
EN 55103-1 Annex A: Radiated magnetic disturbance, 50Hz-50kHz
CISPR 22: Radiated disturbance,
30-1000MHz
CISPR 22: Conducted disturbance,
ac & signal ports
CISPR 16: Discontinuous
disturbance
EN 61000-3-2:2000 Mains
harmonics
EN 61000-3-3:1995 Mains voltage
flicker
Applied EMC immunity test standards:
ref. no. title
EN 61000-4-2:1995 Electrostatic discharge
EN 55103-2:1996 Class A
EN 61000-4-3:1996: Radiated RF disturbance, 80-1000MHz
EN 55103-2 Annex A: Magnetic LF
disturbance, 50Hz–10kHz
EN 61000-4-4:1995: Fast transient
bursts, ac & signal ports
EN 61000-4-5:1995: Surge, ac port
EN 61000-4-6:1996: Conducted RF
field, ac & signal ports
EN 61000-4-11:1994: Mains voltage
dips and interruptions
Place, date: Kidderminster, UK 14th June 2010 General Manager AVP, Product Development Printed name: John Oakley Printed name: Alex Cooper
PRO9 EC-Declaration of Conformity
Midas
DOC04-PRO9ECDOC Rev. A
EC-Declaration of Conformity
The undersigned, representing the following manufacturer
Manufacturer: Address:
Midas Klark Teknik Ltd. Klark Industrial Park, Walter Nash Road, Kidderminster. Worcestershire. DY11 7HJ.
hereby declares that the following product
Product Type Number Product Description Nominal Voltage(s) Current Freq.
PRO9 Control Centre
115V AC 230V AC
2.9A
1.5A
50/60Hz
is in conformity with the regulations of the following marked EC-directives and bears the
-mark accordingly
reference number title
2004/108/EC EMC Directive (EMC)
2006/95/EC Low-Voltage Directive (LVD)
The conformity of the product with EC Directives for use in environment E4 is provided by compliance with the following standards:
Standards/date:
Applied Electrical Safety test standards:
reference number title
EN 60065:2002
Audio, video and similar electronic apparatus. Safety requirements.
Applied EMC emission test standards:
ref. no. title
EN 55103-1:1996 Class A
EN 55103-1 Annex A: Radiated magnetic disturbance, 50Hz-50kHz
CISPR 22: Radiated disturbance,
30-1000MHz
CISPR 22: Conducted disturbance,
ac & signal ports
CISPR 16: Discontinuous
disturbance
EN 61000-3-2:2000 Mains
harmonics
EN 61000-3-3:1995 Mains voltage
flicker
Applied EMC immunity test standards:
ref. no. title
EN 61000-4-2:1995 Electrostatic discharge
EN 55103-2:1996 Class A
EN 61000-4-3:1996: Radiated RF disturbance, 80-1000MHz
EN 55103-2 Annex A: Magnetic LF
disturbance, 50Hz–10kHz
EN 61000-4-4:1995: Fast transient
bursts, ac & signal ports
EN 61000-4-5:1995: Surge, ac port
EN 61000-4-6:1996: Conducted RF
field, ac & signal ports
EN 61000-4-11:1994: Mains voltage
dips and interruptions
Place, date: Kidderminster, UK 18th August 2010 General Manager AVP, Product Development Printed name: John Oakley Printed name: Alex Cooper
Licences
The following are the license agreements applicable to the Midas Digital Equipment.
End-User Licence Agreement for Midas™ and Klark Teknik™ Software
IMPORTANT - Please read this document carefully before using this Midas™ or
Klark Teknik™ Product. This is an agreement governing your use of software or
other machine instructions already installed on this Midas™ or Klark Teknik™
Product, as well as other software that we provide for installation on this Product.
The Midas™ or Klark Teknik™ Product will not operate in accordance with its
documentation without this software.
THIS AGREEMENT ("AGREEMENT" OR "LICENCE") STATES THE TERMS AND CONDITIONS UPON WHICH MIDAS KLARK TEKNIK LIMITED ("COMPANY") OFFERS TO LICENSE THE INSTALLED FIRMWARE, SOFTWARE AND/OR PROGRAMS ("the SOFTWARE") WITH THE MIDAS™ OR KLARK TEKNIK™ CONSOLE OR SIGNAL PROCESSING PRODUCT ("PRODUCT") IN WHICH IT HAS BEEN INSTALLED BY, OR FOR WHICH IT IS PROVIDED BY, THE COMPANY. BY USING THIS PRODUCT YOU WILL BE AGREEING TO BECOME BOUND BY THE TERMS OF THIS LICENCE. IF YOU DO NOT AGREE TO THE TERMS OF THIS LICENCE, DO NOT USE THIS PRODUCT AND PROMPTLY RETURN THE PRODUCT TO THE PLACE WHERE YOU OBTAINED IT FOR A FULL REFUND. You agree to notify any persons whom you permit to operate this Product of the terms of this Licence, and to require them to comply with these terms.
The Software is licensed, not sold, to you for use only under the terms of this Licence, and the Company reserves all rights not expressly granted to you. The Company retains ownership of all copies of the Software itself, and all proprietary parts of it, including those stored on or in the Product.
1. Licence: Subject to the terms and conditions of this agreement, the Company grants you, and other persons you permit to operate the Product, a personal, limited, non-exclusive, non-transferable licence to use the Software only on the single Product unit in which it has been installed.
2. Restrictions: (a) The Software, and the accompanying written materials, are copyrighted and contain trade secrets and other proprietary matter, including confidential information relating to the specifications and performance characteristics of this Product. Save for such elements as may be licensed to the Company, as described in paragraph 5, all rights to copyrights, trade marks and trade secrets in the Software, or any modifications to it, are owned by the Company. Unauthorised use or copying of the Company's proprietary Software, or any portion thereof, or copying of those written materials, is prohibited. (b) You may not create, market, distribute, or transfer copies of the Company's proprietary Software, or any part of it, to others, or duplicate, rent, lease or loan that Software, or any part of it, except that you may transfer that Software installed in this Product in conjunction with the sale, transfer, loan, rent or lease of this Product, and subject at all times to this Licence. YOU MAY NOT REVERSE ENGINEER, DECOMPILE, DISASSEMBLE, EXTRACT OR SEPARAT E OUT, MODIFY, ADAPT, PORT, OR TRANSLATE THE SOFTWARE, DERIVE THE SOURCE CODE OF THE SOFTWARE OR CREATE DERIVATIVE WORKS BASED ON THE SOFTWARE OR ANY ACCOMPANYING WRITTEN MA TERIALS, save as is allowed by licences pertaining to component parts of the Software which are licensed by third parties, as described under paragraph 5, or otherwise by law. (c) In the event you violate any term of this Licence, all rights granted herein will automatically and immediately terminate and you must stop using the Software and destroy any copies of the Software.
3. Limited Warranty: Subject to your installation of any Software updates issued by the Compan y as described herein, and the condition below, the Company warrants that the Software will operate in compliance with the Software's material specifications and documentation for a period of 90 days from your purchase of this Product. The Software is provided "as is" and the Company does not warrant that the operation of the Software will meet your requirements or operate free from error. To the greatest extent permissible by law, the Company DISCLAIMS ALL WARRANTIES AND CONDITIONS, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT OF THIRD PARTY RIGHTS OR CAPABILITY OF CORRECTLY PROCESSING PROVIDING AND/OR RECEIVING
DATE INFORMATION. You understand that the Company may update or revise the Software but in so doing incurs no obligation to furnish such updates to you. However , the Company may in its discretion make updates available from time to time upon such terms and conditions as it shall determine. It is a condition of the above warranty that you install any such Software updates, as may be issued from time to time by the Company for the Software, in accordance with the Company's instructions, and if you do not do so such warranty will cease to apply. You may view current Software updates at http://www.klarkteknik.com and http://www.midasconsoles.com.
4. Limited Liability: THE ENTIRE RISK ARISING OUT OF YOUR USE OR PERFORMANCE OF THE SOFTWARE REMAINS WITH YOU. THE LIABILITY OF THE COMPANY FOR ANY CLAIMS ARISING OUT OF THIS LICENCE AND/OR BASED UPON THE SOFTWARE, REGARDLESS OF THE FORM OF ACTION, AND INCLUDING WORK STOPPAGE, PRODUCT FAILURE OF MALFUNCTION OR ANY OTHER COMMERCIAL LOSS OR DAMAGE, SHALL NOT EXCEED THE COST OF THE LICENCE FEE FOR THE SOFTWARE OR THE COST OF THIS PRODUCT. SUBJECT TO THE PROVISIONS OF APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY LOSS OF DATA, LOST OPPORTUNITY OR PROFITS, COST OF COVER OR SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR INDIRECT DAMAGES, EVEN IF YOU ADVISE THE COMPANY OF THE POSSIBILITY OF SUCH DAMAGES. THIS IS A FUNDAMENTAL TERM OF THIS AGREEMENT AND YOU ACKNOWLEDGE THAT THE AMOUNT YOU PAID FOR THE SOFTWARE AND/OR THE PRODUCT REFLECTS THIS ALLOCATION OF RISK. NOTHING IN THIS PARAGRAPH PURPORTS TO EXCLUDE OR LIMIT THE COMPANY'S LIABILITY FOR DEATH OR PERSONAL INJURY CAUSED BY NEGLIGENCE OR ANY OTHER LIABILITY WHICH CANNOT BE EXCLUDED OR LIMITED BY LAW.
5. Other Third-Party Computer Programs: As referred to herein, the term "Software" refers only to proprietary Midas™ or Klark Teknik™ software, owned by the Company, that has been provided to you for installation on, or already installed in, a Product. In addition to the Softw are, you may have also been provided, at no additional charge, with a version of the widely-available GNU Linux Operating System, which is a modular operating system made up of hundreds of individual software components, each of which was written, and the copyright and other rights in which are owned individually, by various parties (collectively, "the GNU Linux Programs"). Each component has its own applicable end user li cence agreement, and many of these agreements permit you to copy, modify, and redistribute the applicable software, but you must review the on-line documentation that shares a directory or otherwise accompanies each of the GNU Linux Programs provided to you for the specific terms and conditions. Nothing in this Licence limits your rights under, or grants you rights that supersede, the terms of any other applicable end user licence agreement. If you wish to receive a computer-readable copy of the source code for any of the GNU Linux Programs that have been provided with your Midas™ or Klark Teknik™ Product, send a cheque or money order (no cash accepted), your address and [£10.00] to cover the cost of optical media, postage and handling, to:
Midas Klark Teknik Limited ATTN: Linux Programs CD for Midas™/Klark Teknik™ Walter Nash Road, Kidderminster. Worcestershire. DY11 7HJ. England.
In your request, indicate your Product's name and model number, serial number and version/release information. In your request, also indicate the relevant Software version/release information. This offer, made pursuant to the GNU Linux Programs' end user licence agreements, may expire according to the terms of those agreements, in which case your cheque will be returned to you or destroyed at our option. Please note that the GNU Linux Programs that may
be available to you under this offer consists of the GNU Linux Operating System components only and none of the proprietary application software developed by Midas or Klark Teknik is included.
Other updated Linux distributions containing application software are widely available from a variety of Internet sources, and are often available at minimal or no cost.
6. Termination: This Licence will terminate immediately if you violate any of the Licence terms. Upon termination you must discontinue use of the Software, and either destroy, erase or return to Company all copies of the Software in your possession, custody or control, including those in or on the Product.
7. General: This Licence constitutes the entire agreement between you and the Company with respect to this Software and, save in the case of fraud, supersedes any other communication (including advertising). Company reserves all rights not expressly granted to y ou in this licence. If any provision of this Licence is held unenforceable, that provision shall be enforced to the maximum extent permissible so as to give effect the intent of this Licence, and the remainder of this Licence shall continue in full force and effect. This Licence shall be governed by English law
and the Courts of England and Wales will have exclusive jurisdiction to hear and decide any dispute concerning it or its formation. No breach by you of any provision of this Licence shall be waived or discharged except with the express written consent of the Company and no failure or delay by the Company to exercise any of its rights under this Licence shall operate as a waiver thereof and no single or partial exercise of any such right shall prevent any other or further exercise of that or any other right. You acknowledge that the Company could be irreparably damaged if the terms of this Licence were not specifically enforced, and agree that the Company may seek appropriate equitable remedies with respect to breaches of this Licence, including injunctive relief, in addition to such other remedies as the Company may otherwise have available to it under applicable laws.
GNU General Public License (GPL)
For details of the Third Party Software License Attribution, Copyright and Terms and Conditions and Notices, and the GNU LESSER GENERAL PUBLIC LICENSE, see the Midas Digital Equipment GNU General Public License (GPL) Booklet part number DOC04-GPL issue A.
xvii
Precautions
Before installing, setting up or operating this equipment make sure you have read and fully understand all of this section and the “IMPORTANT SAFETY INSTRUCTIONS” at the front of this document.
This equipment is supplied by a mains voltage that can cause electric shock injury! The following must be observed in order to maintain safety and electromagnetic compatibility (EMC)
performance.
Safety warnings
Signal 0V is connected internally to the chassis.
To completely isolate this equipment from the AC mains, while observing full safety precautions (see “Power”), switch off the isolator switch (above the mains power sockets on rear of control centre) and then switch off the mains at the three mains outlets. Unplug the three mains leads from the rear of the control centre.
To avoid electrical shock do not remove covers.
General precautions
In the event of ground loop problems, disconnect the signal screen at one end of the connecting cables. Note that this can only be done when the equipment is used within a balanced system.
Do not remove, hide or deface any warnings or cautions.
Power
The power supplies contain LETHAL VOLTAGES greatly in excess of the mains voltage and its rails can produce extremely large currents that could burn out equipment and wiring if shorted.
distributed so as to meet local safety regulations.
A Volex locking type plug is fitted on each supplied mains cable, which plugs into a mains IEC connector on the equipment. When fitted properly the Volex plug locks into place, preventing it from working loose, or being inadvertently knocked loose or pulled out. To fit a Volex plug, insert it into the mains IEC connector and push it in until it locks in place. Then, check to make sure it is locked in place. To remove it, release its locking device and then pull it out. When fitting or removing a Volex plug, always hold the plug itself and never use the cable, as this may damage it.
During operation of the control centre, a minimum of two of its three mains inlets must be connected and supplying power.
When removing the equipment’s electric plugs from the outlets, always hold the plug itself and not the cable. Pulling out the plug by the cable can damage it.
Never insert or remove an electric plug with wet hands.
Do not connect/disconnect a mains power connector to/from the control centre while power is being applied to it. Switch the power off first.
Before switching the control centre on or off, make sure that all monitor loudspeaker power amplifiers are turned off or muted.
The internal power supplies are of the switch mode type that automatically sense the incoming mains voltage and will work where the nominal voltage is in the range 100VAC to 240VAC.
Each mains inlet is to be sourced from its own separate wall-mounted mains outlet socket. Otherwise, their mains sources must be suitably
PRO Series Live Audio Systems Owner’s Manual
xviii Precautions
Handling the equipment
Completely isolate the equipment electrically and disconnect all cables from the equipment before moving it.
When lifting or moving the equipment, always take its size and weight into consideration. Use suitable lifting equipment or transporting gear, or sufficient additional personnel.
Do not insert your fingers or hands in any gaps or openings on the equipment, for example, vents.
Do not press or rub on the sensitive surface of the GUI screens.
If the glass of the GUI screen is broken, liquid crystals shouldn’t leak through the break due to the surface tension of the thin layer and the type of construction of the LCD panel. However, in the unlikely event that you do make contact with this substance, wash it out with soap.
Installation
Before installing the equipment:
• Make sure the equipment is correctly connected to the protective earth conductor of the mains voltage supply of the system installation through the mains leads.
• Power to the equipment must be via a fused spur(s).
• Power plugs must be inserted in socket outlets provided with protective earth contacts. The electrical supply at the socket outlets must provide appropriate over-current protection.
• Both the mains supply and the quality of earthing must be adequate for the equipment.
• Before connecting up the equipment, check that the mains power supply voltage rating corresponds with the local mains power supply . The rating of the mains power supply voltage is printed on the equipment.
Location
Ideally a cool area is preferred, away from power distribution equipment or other potential sources of interference.
Do not install the equipment in places of poor ventilation.
Do not install this equipment in a location subjected to excessive heat, dust or mechanical vibration. Allow for adequate ventilation around
the equipment, making sure that its fans and vents are not obstructed. Whenever possible, keep the equipment out of direct sunlight.
Do not place the equipment in an unstable condition where it might accidentally fall over.
Make sure that the mains voltage and fuse rating information of the equipment will be visible after installation.
Audio connections
To ensure the correct and reliable operation of your equipment, only high quality, balanced, screened, twisted pair audio cable should be used.
XLR connector shells should be of metal construction so that they provide a screen when connected to the control centre and, where appropriate, they should have Pin 1 connected to the cable screen.
Electrostatic discharge (ESD) precautions
Observe full electrostatic discharge (ESD) — also known as “anti-static” — precautions when carrying out
procedures in this manual that are accompanied by the ESD Susceptibility Symbol (shown above). This caution symbol shows you that ESD damage may be caused to items unless proper ESD precautions are taken, which include the following practices:
• Keep the work area free from plastic, vinyl or
styrofoam.
• Wear an anti-static wrist strap.
• Discharge personal static before handling
devices.
• Ground the work surface.
• Avoid touching ESD-sensitive devices.
Radio frequency interference—Class A device
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
PRO Series Live Audio Systems
Owner’s Manual
Precautions xix
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Electric fields
Caution: In accordance with Part 15 of the FCC Rules & Regulations, “… changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.”
Should this product be used in an electromagnetic field that is amplitude modulated by an audio frequency signal (20Hz to 20kHz), the signal to noise ratio may be degraded. Degradation of up to 60dB at a frequency corresponding to the modulation signal may be experienced under extreme conditions (3V/m, 90% modulation).
Safety equipment
Never remove, for example, covers, housings or any other safety guards. Do not operate the equipment or any of its parts if safety guards are ineffective or their effectiveness has been reduced.
Optional equipment
Unless advised otherwise, optional equipment must only be installed by service personnel and in accordance with the appropriate assembly and usage regulations.
Special accessories
To comply with part 15 of the FCC Rules, any special accessories (that is, items that cannot be readily obtained from multiple retail outlets) supplied with this equipment must be used with this equipment; do not use any alternatives as they may not fulfil the RF requirement.
PRO Series Live Audio Systems Owner’s Manual
xx Precautions
PRO Series Live Audio Systems
Owner’s Manual
xxi
Recommandations
Avant l'installation, la mise au point ou l'exploitation de cet équipement, veiller à lire attentivement et à comprendre l'intégralité de ce chapitre et la partie "CONSIGNES DE SÉCURITÉ IMPORTANTES" au début de ce manuel.
Cet équipement est alimenté par une tension de secteur pouvant provoquer des blessures par choc électrique !
Les points suivants doivent être observés afin de maintenir la sécurité et une compatibilité électromagnétique (CEM) correcte.
Avertissements de sécurité
Une tension 0V de signal est raccordée en interne au châssis.
Afin de déconnecter complètement cet appareil du secteur CA, tout en observant les précautions de sécurité (voir “Puissance”), couper le sectionneur (au­dessus des prises secteur sur le panneau arrière du centre de contrôle), puis couper le secteur aux trois socles de secteur. Isoler l'appareil en débranchant les trois câbles de secteur du panneau arrière du centre de contrôle.
Afin d'éviter un choc électrique, ne pas retirer les couvercles.
Recommandations générales
En cas de problème de boucle de terre, débrancher le blindage de signal à une extrémité des câbles de raccordement. Il convient de noter que cela n'est faisable que si l'équipement est utilisé dans un système équilibré.
Ne pas retirer, cacher ni dégrader les avertissements ou les mises en garde.
Puissance
Les alimentations électriques contiennent des TENSIONS LÉTALES largement supérieures à la tension de secteur et les barres peuvent produire des courants extrêmement élev és capables de griller l'équipement et le câblage en cas de court-circuit.
Les alimentations électriques internes sont des alimentations à découpage détectant
automatiquement la tension de secteur d'entrée et fonctionnant lorsque la tension nominale se trouve dans la plage de 100 VCA à 240 VCA.
Chaque prise de secteur doit être raccordée à son propre socle mural séparé. Sans quoi, les alimentations de secteur doivent être correctement distribuées conformément aux réglementations locales de sécurité.
Chaque câble d'alimentation fourni est équipé d'une fiche Volex verrouillable qui se branche dans une prise connecteur CEI sur l'appareil. Lorsqu'elle est montée correctement la fiche Volex se verrouille dans son logement, l'empêchant de se desserrer ou d'être déconnectée par inadvertance. Pour brancher une fiche Volex, l'insérer dans la prise connecteur secteur CEI et la pousser jusqu'à ce qu'elle se verrouille dans son logement. Penser ensuite à vérifier qu'elle soit correctement verrouillée. Pour l'enlever, libérer son dispositif de verrouillage pour ensuite la tirer. Lors de la connection ou déconnection d'une fiche Volex, toujours saisir la fiche elle-même et ne jamais utiliser le câble, car cela pourrait l'endommager.
Pendant le fonctionnement du centre du contrôle un minimum de deux de ses trois entrées secteur doivent être connectés et alimentation.
Pour débrancher les cordons d'alimentation de l'équipement des prises murales, tenir toujours la prise et non le câble. Tirer la prise par le câble peut l'endommager.
Ne jamais brancher ni débrancher une prise électrique avec des mains humides.
Ne jamais brancher/débrancher un connecteur de secteur au/du centre de contrôle s'il est sous tension. Mettre d'abord hors tension.
Avant de metre le centre de contrôle ou se désactiver, assurez-vous que tous les amplificateurs de haut-parleur de surveiller l'alimentation sont désactivées ou coupé.
PRO Series Live Audio Systems Owner’s Manual
xxii Recommandations
Manipulation de l'équipement
Isoler électriquement et totalement l'appareil et débrancher tous ses câbles avant de le déplacer.
En soulevant ou en déplaçant l'appareil, tenir toujours compte de sa taille et de son poids. Utiliser un dispoitif de levage adapté ou un matériel de transport, ou encore suffisamment de personnel supplémentaire.
Ne pas introduire les doigts ni les mains dans les fentes ni les ouvertures de l'appareil, telles que les ouïes de ventilation.
Ne pas appuyer ou de frotter sur la surface sensible des ecrans GUI.
Si le verre de l’écran GUI est cassé, les crystaux liquids ne doit pas s’infiltrer dans la rupture en raison de la tension superificielle de la couche mince et le type de construction de l’écran LCD. Toutefois, dans le cas improbable où vous ne prendre contact avec cette substance, le laver avec du savon.
Installation
Avant d'installer l'équipement :
• Vérifier qu'il est correctement raccordé au conducteur de terre de protection de l'alimentation de tension de secteur du système par les câbles de secteur.
• L'équipement doit être alimenté par l'intermédiaire de(s) dérivation(s) avec fusible.
• Les prises doivent être branchées sur des prises femelles dotées de contacts de terre de protection. L'alimentation électrique aux prises femelles doit assurer une protection adéquate contre la surintensité.
• L'alimentation de secteur et la qualité de la mise à la terre doivent être d'un niveau convenant à l'appareil.
• Avant de brancher l'équipement, vérifier que la tension nominale de l'alimentation de secteur correspond à l'alimentation de secteur locale. La valeur nominale de la tension d'alimentation de secteur est imprimée sur l'équipement.
Ne pas installer l'équipement dans des endroits mal aérés.
Ne pas installer cet équipement dans un local exposé à la chaleur, à la poussière ou à des vibrations mécaniques excessives. Prévoir une ventilation adéquate autour de l'appareil, en s'assurant que les ventilateurs et les ouïes ne sont pas obstrués. Dans la mesure du possible, le garder à l'écart de la lumière directe du soleil.
Ne pas placer l'appareil sur un support instable d'où il pourrait tomber par accident.
S'assurer que les informations relatives à la tension de secteur et au calibre des fusibles de l'équipement sont visibles après l'installation.
Connexions audio
Afin d'assurer le fonctionnement correct et fiable de l'équipement, utiliser uniquement un câble audio à paire torsadée, blindé, équilibré, de première qualité.
Les boîtiers de connecteurs XLR doivent être en métal de façon à former un blindage lors du raccordement au centre de commande et, le cas échéant, la Fiche 1 devrait être raccordée au blindage du câble.
Electrostatic discharge (ESD) precautions
Observe full electrostatic discharge (ESD) — also known as “anti-static” — precautions when carrying out
procedures in this manual that are accompanied by the ESD Susceptibility Symbol (shown above). This caution symbol shows you that ESD damage may be caused to items unless proper ESD precautions are taken, which include the following practices:
• Keep the work area free from plastic, vinyl or
styrofoam.
• Wear an anti-static wrist strap.
• Discharge personal static before handling
devices.
• Ground the work surface.
• Avoid touching ESD-sensitive devices.
Lieu d'installation
L'idéal est de disposer d'une zone fraîche, à l'écart de tout équipement de distribution électrique ou d'autres sources potentielles d'interférences.
PRO Series Live Audio Systems
Owner’s Manual
Recommandations xxiii
Interférences radioélectriques - Dispositif de Classe A
Cet équipement a été testé et est conforme aux limites d'un produit numérique de Classe A, en application de la Partie 15 des Règles de la FCC. Ces limites sont destinées à assurer une protection raisonnable contre les interférences néfastes lorsque l'équipement fonctionne dans un environnement commercial. Cet équipement génère, utilise et peut rayonner de l'énergie de fréquence radio et, s'il n'est pas installé et utilisé conformément au manuel d'exploitation, il peut causer des interférences dommageables aux communications radio. L'utilisation de cet équipement dans une zone résidentielle est susceptible de provoquer des interférences néfastes, dans quel cas l'utilisateur se devra de corriger les interférences à ses propres frais.
Champs électriques
Attention : Conformément à la Partie 15 des Règles et
Réglementations de la FCC, "… tout changement ou toute modification non expressément approuvé(e) par la partie responsable de la conformité pourrait annuler l'autorisation accordée à l'utilisateur d'utiliser cet appareil. "
Dans le cas où ce produit est utilisé dans un champ électromagnétique dont l'amplitude est modulée par un signal audiofréquence (20 Hz à 20 kHz), le rapport signal-bruit peut être
détérioré. Une détérioration atteignant 60 dB à une fréquence correspondant au signal de modulation peut se produire dans des conditions extrêmes (modulation 90%, 3 V/m).
Équipement de sécurité
Ne jamais retirer les couvercles, les boîtiers ni autres caches de sécurité. Ne pas faire fonctionner l'appareil ni aucun de ses composants si les protecteurs de sécurité ne sont pas en mesure de remplir leur fonction ou si leur efficacité a été réduite.
Équipement en option
Sauf indication contraire, tout équipement en option doit être installé uniquement par le personnel d'entretien et conformément aux réglementations appropriées de montage et d'usage.
Accessoires spéciaux
Aux fins de la conformité à la Partie 15 des Règles de la FCC, tous les accessoires spéciaux fournis avec cet équipement (à savoir les articles que l'on ne peut se procurer facilement auprès des chaînes de détaillants), doivent être utilisés avec cet équipement ; ne pas utiliser de composants de remplacement car ils pourraient ne pas respecter l'exigence de RF.
PRO Series Live Audio Systems Owner’s Manual
xxiv Recommandations
PRO Series Live Audio Systems
Owner’s Manual
xxv
Contents
Cover page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Information page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .v
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES. . . . . . . . . . . . . . . . . . . . . vi
PRO6 EC-Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
PRO6 EC-Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
PRO9 EC-Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Licences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii
Recommandations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxv
Overview
Chapter 1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
GUI diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PRO Series user documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PRO Series host software version . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Warranty and registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Service and support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2 PRO Series Live Audio Systems . . . . . . . . . . . . . . . . . .7
Introducing the PRO3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Introducing the PRO6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Introducing the PRO9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PRO Series Live Audio Systems Owner’s Manual
xxvi Contents
System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
FOH and MON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
System buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Mix matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Processing components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Input channel processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Mix channel processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Output channel processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Effects processing and GEQs . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Audio physical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Surround capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Reliability (redundancy) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Control software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
System card expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Console linking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Integration of third party hardware/software . . . . . . . . . . . . . . . . . . .24
Chapter 3 About The Control Centre . . . . . . . . . . . . . . . . . . . . . 27
Overview of the control centre . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Bay and GUI layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Control surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Front and rear panel connections . . . . . . . . . . . . . . . . . . . . . . . . . . .31
External interfaces and peripheral devices . . . . . . . . . . . . . . . . . . . . .32
Mix buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Automation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Processing elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Getting Started
Chapter 4 Setting Up The System . . . . . . . . . . . . . . . . . . . . . . . 37
Initial set-up procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Unpacking the equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Making up a rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Outboard equipment rack requirements . . . . . . . . . . . . . . . . . . . . .37
Wiring instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Powering the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Switching the control centre on/off . . . . . . . . . . . . . . . . . . . . . . . . . .43
Setting up the ID of the unit(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Basic Operation Of The PRO Series
Chapter 5 Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Principles of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Normal mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Using the 4-channel input bay as area B . . . . . . . . . . . . . . . . . . . .47
PRO Series Live Audio Systems
Owner’s Manual
Contents xxvii
Operating the top output fast strips from the master bay . . . . . . . . 48
Controlling the mix buses in flip mode . . . . . . . . . . . . . . . . . . . . . 48
Hints and tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Saving your work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Saving a show versus storing a scene . . . . . . . . . . . . . . . . . . . . . . 49
Shutting down the control centre properly . . . . . . . . . . . . . . . . . . 49
Chapter 6 Working With The Control Centre . . . . . . . . . . . . . . .51
About the PRO Series controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
About channel operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
About GUI operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Click . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Drag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Common GUI screen elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Parameter values displayed on touch . . . . . . . . . . . . . . . . . . . . . . . . 54
Operating the GUI screen controls . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Using drop-down lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Spin buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
About windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Using the GUI menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Text editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Chapter 7 Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
An introduction to navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Navigating the input channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Navigating the mix buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Navigating the output channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Navigation via the GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Fault finding a problem channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Chapter 8 Patching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Terms used in PRO Series patching . . . . . . . . . . . . . . . . . . . . . . . . . . 71
About the Patching screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
What the Patching screen symbols mean . . . . . . . . . . . . . . . . . . . 74
About the tabs in the From and To sections . . . . . . . . . . . . . . . . . . 75
Navigating to the Patching screen . . . . . . . . . . . . . . . . . . . . . . . . 85
About the devices on the stage and FOH I/O tabs . . . . . . . . . . . . . 85
Patching tooltips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Standard tooltip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
List tooltip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
About the patching procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Configuring the devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
About the configuration window . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Device configuration procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Configuring the snake type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Setting up the I/O rack devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Device set-up procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
How to patch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Working with patch connectors . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Single patching (SINGLE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Sequence patching (SEQ.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
PRO Series Live Audio Systems Owner’s Manual
xxviii Contents
Automatic patching (AUTO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Clearing all current patching . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Chapter 9 Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Setting a mic amplifier’s input gain . . . . . . . . . . . . . . . . . . . . . . . . . .99
Setting the high and low pass filters . . . . . . . . . . . . . . . . . . . . . . . .100
Input equalisation (E zone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Input dynamics processing (D zone) . . . . . . . . . . . . . . . . . . . . . . . .102
Output processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Using VCA/POP groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Configuring VCA/POP groups . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Setting up a mix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Mix bus routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Linking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Using fader flip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Setting up the effects rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Simple routing to master stereo outputs . . . . . . . . . . . . . . . . . . . . .111
Scene and show management (automation) . . . . . . . . . . . . . . . . . . .112
Managing the shows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Managing the scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Additional control — managing events . . . . . . . . . . . . . . . . . . . . .116
Show editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Configuring the inputs and outputs . . . . . . . . . . . . . . . . . . . . . . . . .118
Using copy and paste . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Copy and paste rules and restrictions . . . . . . . . . . . . . . . . . . . . .119
User library (presets) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Surround panning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Two-man operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Saving your show files to a USB memory stick . . . . . . . . . . . . . . . . .123
External AES50 synchronisation . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Security (locking mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Advanced Operation And Features
Chapter 10 Stereo Linking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Changing the linking options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Linking the master channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Chapter 11 Panning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Stereo panning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
SIS™ (LCR) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
SIS image control knob fully clockwise (LCR) . . . . . . . . . . . . . . . .132
SIS image control knob fully anti-clockwise (stereo) . . . . . . . . . . .132
SIS image control knob centred (equal power) . . . . . . . . . . . . . . .132
Surround panning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
About the controls in surround mode . . . . . . . . . . . . . . . . . . . . . .134
Speaker placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
PRO Series Live Audio Systems
Owner’s Manual
Contents xxix
Chapter 12 Soloing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Using solo A/B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Solo hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Solo in place (SIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Chapter 13 Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141
Chapter 14 Monitors And Communications . . . . . . . . . . . . . . . .143
Monitors (A and B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Delay (GUI only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Solo system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
solo in place switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
C/O switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Monitor output (a and b) sections . . . . . . . . . . . . . . . . . . . . . . . 147
source (a and b) sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
solo (a and b) sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
solo mode section (GUI only) . . . . . . . . . . . . . . . . . . . . . . . . . . 149
solo system section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Signal generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Talk osc/routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Internal talk groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Talk mic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Internal talk mic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
External talkback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Chapter 15 Graphic Equaliser (GEQ) . . . . . . . . . . . . . . . . . . . . .157
Overview of the GEQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
About the Graphic EQs screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
About the GEQ window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
GEQ front panel features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Configuring the number of GEQs (and effects) . . . . . . . . . . . . . . . . . 161
Copying settings between GEQs . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Chapter 16 Internal Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
Overview of the internal effects . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Rack unit number allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
About the effect window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Working with the effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Effect configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Effect programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Delay effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Virtual DN780 Reverb effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Flanger effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Phaser effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Pitch Shifter effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
SQ1 Dynamics effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
3-Band Compressor effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
PRO Series Live Audio Systems Owner’s Manual
xxx Contents
Chapter 17 Control Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
VCA and POP groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
VCA fast strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178
POP groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179
Working with VCA/POP groups . . . . . . . . . . . . . . . . . . . . . . . . . .179
Auto-mute (mute) groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
Talk groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181
About the control group screens . . . . . . . . . . . . . . . . . . . . . . . . . . .182
Management section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182
Programming the groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
Configuring the groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184
Chapter 18 Copy And Paste . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Channels versus scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185
Chapter 19 Assignable Controls (I Zone) . . . . . . . . . . . . . . . . . 187
About the I zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187
Controlling a rotary control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187
About the Assignable Controls window . . . . . . . . . . . . . . . . . . . .188
Using the I zone to control an internal effect/GEQ . . . . . . . . . . . . . . .190
About the assignable controls panel on the GUI . . . . . . . . . . . . . .190
Rack and unit control navigation . . . . . . . . . . . . . . . . . . . . . . . . .191
Controlling an internal effect via the I zone . . . . . . . . . . . . . . . . . . .193
Controlling a GEQ via the I zone . . . . . . . . . . . . . . . . . . . . . . . . . . .194
Chapter 20 Scenes And Shows (Automation) . . . . . . . . . . . . . . 197
About automation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197
Automation controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198
next LCD button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199
Automation screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199
Using the right-click menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200
Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201
Scene contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
Point scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
Numbering and navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
Global scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
Initial snapshot scene (scene 0) . . . . . . . . . . . . . . . . . . . . . . . . . . .202
Date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Scene cue list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203
Configuring the scene cue list view . . . . . . . . . . . . . . . . . . . . . . .205
Editing scene properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .205
Adding a new scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206
Copying and deleting scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206
Changing the order of the scenes . . . . . . . . . . . . . . . . . . . . . . . . . .207
Overriding store scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207
Using patching in automation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208
Using zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208
Show files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
Managing show files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
Managing show files on the Files screen . . . . . . . . . . . . . . . . . . . .210
Rehearsals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .210
Safes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211
PRO Series Live Audio Systems
Owner’s Manual
Contents xxxi
Chapter 21 Scope (Automation). . . . . . . . . . . . . . . . . . . . . . . . .213
About scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
About the Recall Scope screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Selecting scope parameter sections . . . . . . . . . . . . . . . . . . . . . . . . 215
Selecting bus parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
Saving scope parameters in a scene . . . . . . . . . . . . . . . . . . . . . . . . 219
Using store scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
Chapter 22 Events (Automation) . . . . . . . . . . . . . . . . . . . . . . . .221
About events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Crossfades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Global scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Connecting up the MIDI/GPIO equipment . . . . . . . . . . . . . . . . . . 222
About the Edit Event window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Programming events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Chapter 23 Crossfades (Automation). . . . . . . . . . . . . . . . . . . . .227
About the crossfade Edit Event window . . . . . . . . . . . . . . . . . . . . . . 227
About the crossfade parameters . . . . . . . . . . . . . . . . . . . . . . . . 228
Crossfade set up section in the Edit Event window . . . . . . . . . . . . 229
How a crossfade operates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Crossfade groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Global events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
Manually controlling a crossfade . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Chapter 24 User Libraries (Presets). . . . . . . . . . . . . . . . . . . . . .235
About the Preset Manager screen . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Managing user libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
Deleting presets from a user library . . . . . . . . . . . . . . . . . . . . . . . . 237
Chapter 25 File Management . . . . . . . . . . . . . . . . . . . . . . . . . . .239
About the Files screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
About the Master Controller File Synchronisation window . . . . . . . . . 241
Chapter 26 Using Other Devices With The PRO Series. . . . . . . .243
Using multiple digital consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Synchronising the consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Sharing DL431 Mic Splitter A and B inputs . . . . . . . . . . . . . . . . . 244
Using an external USB mouse . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
Using an external USB keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . 244
Using an external monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Chapter 27 Changing The User Settings. . . . . . . . . . . . . . . . . . .247
Setting the meter preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Configuring a virtual soundcheck . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Restoring the PRO Series defaults . . . . . . . . . . . . . . . . . . . . . . . . . 248
Checking the PRO Series build information . . . . . . . . . . . . . . . . . . . 248
Setting the configuration preferences . . . . . . . . . . . . . . . . . . . . . . . 249
Changing the user interface preferences . . . . . . . . . . . . . . . . . . . . . 250
PRO Series Live Audio Systems Owner’s Manual
xxxii Contents
Changing the signal processing preferences . . . . . . . . . . . . . . . . . . .250
Configuring the channels, groups and internal units . . . . . . . . . . . . .251
Changing the default input/output names . . . . . . . . . . . . . . . . . . . .251
Adjusting PRO Series illumination . . . . . . . . . . . . . . . . . . . . . . . . . .251
Setting the time and date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .252
Chapter 28 Delay Compensation (Latency) . . . . . . . . . . . . . . . . 253
Insert compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253
GEQ compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .254
GUI Delay Compensation options . . . . . . . . . . . . . . . . . . . . . . . . . .254
Monitor Mode (Align with Masters) . . . . . . . . . . . . . . . . . . . . . . . . .256
Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257
Master to matrix post-processing option . . . . . . . . . . . . . . . . . . . . .257
Solo bus delay compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258
Typical configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259
FOH mix setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259
FOH mix low latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .260
Monitor mix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261
Monitor mix (low latency) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262
Description
Chapter 29 Panel Connections. . . . . . . . . . . . . . . . . . . . . . . . . . 265
Front panel connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265
Rear panel connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .266
Mains power and ventilation section . . . . . . . . . . . . . . . . . . . . . .266
External connections and communications (centre left) section . . .267
Audio, networking and synchronisation section . . . . . . . . . . . . . . .273
I/O section (far right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .276
Chapter 30 Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
Input channel routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277
Input channel areas of the control surface . . . . . . . . . . . . . . . . . . . .278
Input fast strips, channel strips and mix buses . . . . . . . . . . . . . . . . .279
Inputs on the GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280
GUI input fast strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280
GUI channel strips (inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . .280
Input metering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .282
Channel configuration controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Input channel ID (GUI only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .284
Input channel source select (GUI only) . . . . . . . . . . . . . . . . . . . .284
Input channel delay (GUI only) . . . . . . . . . . . . . . . . . . . . . . . . . .284
Stereo linking (GUI only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284
Safes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .285
Mic amp input gain (preliminary input processing) . . . . . . . . . . . . . .286
Using gain swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288
Processing order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288
Direct output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .288
Dynamics (D zone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .290
Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .290
Compressor graph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .292
PRO Series Live Audio Systems
Owner’s Manual
Loading...
+ 636 hidden pages