Page 1
CONTENT
FCC Compliance Statement .................................................................... ii
Safety Precautions .................................................................................. iii
Care and Maintenance ........................................................................... iv
Introduction ..............................................................................................1
Product Package .......................................................................................2
Installing the Monitor ...............................................................................3
Control Functions .....................................................................................4
Adjusting the Monitor .............................................................................. 6
Factory-Preset Modes ........................................................................... 10
Specifications ......................................................................................... 11
Signal Connector Pin Assignment ........................................................ 13
i
Page 2
Operation Instructions
Thank you for purchasing this monitor, a high-resolution multi-scan color monitor.
Please read this guide thoroughly before installation.
FCC RADIO FREQUENCY INTERFERENCE STATEMENT
WARNING:(FOR FCC CERTIFIED MODELS)
This monitor has been tested and found compliant with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
proper protection against harmful interference to a residential installation. This
monitor generates, uses, and can radiate radio frequency energy. Harmful
interference to radio communication may result if it’s not properly installed and
used. However, there is no guarantee that interference will not occur in a particular
installation. If this monitor does cause serious interference to radio or television
reception, resetting the monitor may determine it. Moreover, users are encouraged
to correct interference by doing one or more of the following:
• Reorient or relocate the receiving antenna.
• Move the monitor and the receiver further away from each other.
• Connect the monitor into an outlet on a circuit different from that to which
the receiver is connected.
• Consult your local dealer or an qualified technician.
FCC Warning:
To assure a continued FCC compliance, a user must use a grounded power supply
cord and the provided shielded video interface cable with bonded ferrite cores. Also,
any unauthorized changes or modifications to this monitor would void the user’s
authority to operate this device.
Note: If necessary, shielded interface cables and the A.C. power cord must be used
to meet the emission level limits.
EMI Certification
The Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulation. Cet appareil numerique de class B respecte toutes
les exigences du Reglement sur Ic materiel brouilleur du Canada.
Note
This user’s manual contains graphics and information that is for reference purpose
only and is subject to change without notice.
ii
Page 3
Safety Precautions
This monitor is manufactured and tested on the ground principle that a user’s safety
comes first. However, improper use or installation may not only damage the
monitor but also endanger the user. As a safety precaution, go over the following
WARNINGS carefully before installation, and keep this guide handy.
WARNINGS:
• This monitor should be operated only at the correct power sources
indicated on the label at the rear end of the monitor. If you are unsure of the
power supply in your residence, consult your local dealer or power
company.
• Do not try to repair the monitor yourself as it contains no user-serviceable
parts. The monitor should only be repaired by a qualified technician.
• Do not remove the monitor cabinet. There are high-voltage parts inside that
may cause electric shock to human bodies, even when the power cord is
disconnected.
• Stop using the monitor if the cabinet is damaged. Have it checked by a
service technician.
• Put your monitor only in a clean, dry environment. Unplug the monitor
immediately if it gets wet, and consult your service technician.
• Always unplug the monitor before cleaning it. Clean the cabinet with a
clean, dry cloth. Apply non-ammonia-based cleaner onto the cloth, not
directly onto the glass screen.
• Keep the monitor away from magnetic objects, motors, TV sets, and
transformers.
• Do not place heavy objects on the cable or power cord.
• For PLUG CABLE EQUIPMENT, the socket outlet should be installed near
the equipment and should be easily accessible.
iii
Page 4
Care and Maintenance
Care
• Avoid exposing your monitor directly to sunlight or other heat sources.
Place your monitor away from the sun to reduce glare.
• Put your monitor in a well-ventilated area. Do not place anything heavy on
top of your monitor.
• Make certain that your monitor is installed in a clean and moisture-free
area.
• Keep your monitor away from magnets, motors, transformers, speakers,
and TV sets.
Safety Tips
• If smoke, abnormal noise or odor comes out of your monitor, switch off the
power immediately and call your service center.
• Never remove the rear cover of your monitor cabinet. The display unit
inside contains high-voltage parts and may cause electric shock to human
bodies.
• Never try to repair the monitor yourself. Always call your service center or
a qualified technician to fix it.
iv
Page 5
INTRODUCTION
BEFORE INSTALLING YOUR MONITOR
READ THIS MANUAL COVER TO COVER. P A Y A TTENTION to
WARNING and CAUTION signs. DO NOT use computer components not
recommend by the manufacturer. Do not attempt to service the monitor
yourself. If a problem occurs, contact your dealer or authorized service
center.
ABOUT YOUR MONITOR
This monitor is a microprocessor-controlled color monitor which uses a
TFT LCD panel. The monitor conforms to EP A Energy Star and VESA
DPMS (Display Power Management Signaling) power management
standards.
RGB MODE
This monitor is equipped with a microprocessor that identifies your
computer’s video mode and allows users to adjust the setting.
1
Page 6
PRODUCT PACKAGE
Open the shipping carton and check the contents. If any items are missing
or damaged, contact your dealer immediately.
The package should include the following items:
• Analog Color TFT LCD Monitor
• Accessory Box:
1. VGA cable x1
2. AC-DC adapter x1
3. Audio cable
4. Power Cord x 1
5. User’s manual x1
2
Page 7
INSTALLING THE MONITOR
The monitor is equipped with an auto-sensing power supply for voltage
ranging from 110~240VAC, 60/50Hz. Confirm the line voltage designation
on the rear panel of the monitor.
Follow these steps to install the monitor:
1. Before you connect the cables, make sure that the monitor and the
system unit power switches are OFF.
2 . Plug one end of the 15pin signal cable to the monitor and the other
end to the video signal connector at the rear of the system. Tighten
the two screws on the cable connector on both ends. Otherwise, the
screen will be abnormal and the LED light will be yellow in color
(instead of the normal green).
3 . Connect the power to the monitor throught the AC-DC adapter.
4 . Connect the power cord on the AC outlet. See illustration below.
3
Page 8
CONTROL FUNCTIONS
The Monitor control functions are located on the lower center of the front
panel. Details follow below.
Description of control keys:
1. : Power Switch
2 . - / + : Decrease/Increase or Volume control
3. / : Cursor Up/Down or Brightness control
4. MENU: Activates on-screen display functions
5. Auto: Automatic adjustment
4
Page 9
1. : Power switch
Use the power switch to turn power ON or OFF . We recommend
turning your system power on first, followed by the LCD monitor.
2. - & + : Decrease & Increase/Volume Control keys
These keys have two functions, controlled by the MENU key. When
the OSD screen is activated, these two keys are uses to decrease or
increase the values of the selected items. When the OSD screen is
NOT activated, these two keys are used to turn up or turn down
volume.
3. & : Select key/Brightness Control keys
These keys have two functions, controlled by the MENU key. When
the OSD screen is activated, these two keys are used to move the
cursor up or down to select item. When the OSD screen is NOT
activated, these two keys are used to change the Brightness value.
4. MENU
Press the Menu key to activate the on-screen display screen. The
Menu key is a toggle key; press twice to either turn the on-screen
display ON or OFF . After 30 seconds of idle time, the OSD screen will
automatically turn off.
5. Auto adjustment
Press this key to get better visual performance.
5
Page 10
ADJUSTING THE MONITOR
The LCD monitor is designed to work with a range of compatible video
adapters on the market. Due to possible deviations between these video
adapters, you may need to make some adjustments on the adapter to make
sure it fits your monitor.
ADJUSTMENT PROCEDURE
1 . Activate the OSD screen by pressing the MENU key. The screen
below will appear.
OSD SCREEN
1280X1024 75 Hz/80 KHz
AUTO ADJUSTMENT
LANGUAGE
DOS TXT/GFX OFF
USER
50
OFF
100
VERSION SXGAAF181-6123
2 . Use the & key to select the required adjustment item up or down.
3 . Use the - & + key to perform the desired function or go into the
second menu item to perform further changes.
6
Page 11
AUTO-ADJUSTMENT
Note: W e strongly recommend that you use this item to get optimum visual
quality.
Use the & key to select auto-adjustment, then press - or + to get the
optimized quality .
RGB ADJUSTMENT
Use the & key to select the icon, then press - or +. The screen below
will appear .
1280X1024 75 Hz/80 KHz
Auto-Balance
CONTRAST
RED 20
GREEN 18
BLUE 19
BALANCE
RED 49
GREEN 50
BLUE 26
VERSION SXGAAF181-6123
Adjust the contrast value
• Use the & key to select the CONTRAST item, then press - & + to
get the best contrast optimization. Y ou can adjust R,G,B
simultaneously or separately. You can also use this item to change
RGB purity .
Color Balance
• Use the & key to select the BALANCE item, then press - & + to
get the best color balance effect or to set the RGB color values
separately . You can use this item to change RGB intensity.
Note: The easiest way to adjust contrast and color balance is to use the
auto-balance item.
7
Page 12
GEOMETRY ADJUSTMENT
Use the & key to select the icon, then press - or +. The screen below
will appear.
1280X1024 75 Hz/80 KHz
223
24
1056
PHASE 25
VERSION SXGAAF181-6123
If you want to go back to the previous OSD menu screen, press the MENU
key, The OSD screen will then appear .
Vertical & Horizontal Position adjustment
1 . Use the & key to move to the ICON, then press - & + to move the
whole screen left to right to the center position.
2 . Use the & key to move to the ICON, then press - & + to move the
whole screen down or up to the center position.
Adjust the viewing screen size
• Use the & key to move the icon, then press - & + to get the larger
viewing size.
PHASE adjustment
Adjust phase tracking of the display signal to reduce display flicker.
Invalid phase tracking will cause unstable and flicking display.
• Use the & key to move to the Phase item, then press - &+ to get a
better image quality.
8
Page 13
Multi-language
Five OSD languages are supported for customer selection.
1280X1024 75 Hz/80 KHz
English
German
French
Italian
Spanish
VERSION SXGAAF181-6123
DOS Txt/GFX
Display mode of 640 x 400 (graphic mode) or 720 x 400 (text mode) is
supported.
Color Temperature
Three modes are provided: user mode, 6500, and 9300. User the & key
to move to the color temperature item, then press - & + to select the color
temperature setting. If the 6500 or 9300 values are set, the value cannot be
changed.
Brightness adjustment
Use the & key to select the item, then press - & + to change the
brightness value.
Audio volume control
Use the & key to select the item, then press - & + to turn the volume
down or up.
Mute On/Off
Use the & key to select the item, then press - & + to turn the mute
function on or off.
UNDERSTANDING THE DISPLAY RESOLUTION SETTING
In the OSD screen, you will see the Horizontal frequency (HF), V ertical
frequency (VF), display resolution (MODE) and the monitor Firmware
version (ROM LEVEL). These settings are automatically detected by the
monitor and cannot be changed by the user.
9
Page 14
FACTORY-PRESET MODES
Table 1 shows standard video mode settings that have been pre-adjusted
at the factory for accurate video display. These setting are stored in the
monitors memory.
T able 1. Factory-Preset Modes
Mode
NEC
VGA
SVGA
XGA
SXGA
Macintosh
Resolution
640 x 400
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
1280 x 1024
640 x 480
H-Freq.(KHz)
24.83
31.47
31.47
31.47
37.86
37.5
35.16
37.88
48.08
46.87
48.36
56.47
60
63.98
80
35
V-Freq (Hz)
56.4
70
70
60
72
75
56.3
60.3
72.2
75
60
70
75
60
75
66.7
832 x 624
1024 x 768
1024 x 768
10
49.7
48.78
60.241
74.55
60
74.927
Page 15
SPECIFICATIONS
17" LCD Monitor
Overall Dimensions (H x W x D): 426 x 444 x 215 mm
Shipping W eight (G/W): 10 K g
Effective display area (H/V) 337.92 x 270.34 mm
Display colors: 16.7 million colors
Brightness: 200 cd/m2 (min)
Contrast Ratio: 300:1
Scan Frequencies:
Horizontal 31.47 KHz to 80 KHz
V ertical 60 Hz to 75 Hz
Number of Pixels: 1280 x 1024 pixels
Pixel pitch: 0.264 x 0.264 mm
Picture Tube: 17" TFT LCD panel
Power:
Input 1 10-240 VAC (auto-sensing)
Consumption 42 W atts maximum (on)
Frequency: 48-62 Hz
1 W atts (Power saving of f mode)
V ideo Connector: 15 pin Mini D-sub (Standard)
Audio connector 1 x stereo input
1 x Microphone output
Speaker 2 W x 2
RGB Signals:
Video Analog RGB 0.7Vp-p/75
Sync Separate
Display Data Channel:
Compatibility VESA DDC 1/2B
11
Page 16
OPERATIONS
User Controls On/Off Power Button
Select and adjust button
Auto-adjustment
On Screen Display Contract, Brightness
Adjustment H-position, V-position
Color temperature
Multi-language
Auto Adjustment
V olume, Mute
Control T ype: Digital
Compatibility: IBM and compatibles, Apple
Macintosh, NEC
Environmental Limits:
Operating T emp. 32° to 113°F (0° to 45°C)
Storage Temp. -4° to 140°F (-20° to 60°C)
Operating Humidity 10 to 85% without condensation
Storage Humidity 10 to 95% without condensation
Agency Approval FCC-B and CE
EMI MPR-II
Emissions EP A energy star , VESA DPMS
Energy Saving UL, TUV
Safety
12
Page 17
SIGNAL CONNECTOR PIN ASSIGNMENT
Power Connector
Pin 1
Pin 2
RGB Signal connector
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Ground
+12V output
Analog Red Input
Analog Green Input
Analog Blue Input
Ground
Digital Ground
Analog Red Input
Analog Green Input
Analog Blue Input
NC
Sync Ground
Ground
Pin 12
Pin 13
Pin 14
Pin 15
SDA (DDC Data)
H.Sync
V.Sync
SCL (DDC CLK)
13
Loading...