Microsoft LPS 6 User Manual

User Guide

Nokia Wireless Loopset LPS-6

Issue 1 EN

User Guide

Nokia Wireless Loopset LPS-6

Safety 3 Get started 4

Keys and parts 4

Charge the battery 4

Take the loopset into use 5

Pair and connect your loopset with your phone 6

Pair and connect your loopset using NFC 6

Basic use 8

Make and receive calls 8

Handle two calls 8

Listen wirelessly with Bluetooth 8

Use USB audio connection 9

Change the volume 9

Clear settings or reset your loopset 10

Troubleshooting 11 Product and safety information 12 Copyrights and other notices 16 Copyrights and other notices 19

Safety

Read these simple guidelines. Not following them may be dangerous or illegal.

We invite you to read the instructions on this guide before using the device.

SWITCH OFF IN RESTRICTED AREAS

Switch the device off when mobile phone use is not allowed or when it may cause interference or danger, for example, in aircraft, in hospitals or near medical equipment, fuel, chemicals, or

blasting areas. Obey all instructions in restricted areas.

ROAD SAFETY COMES FIRST

Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.

INTERFERENCE

All wireless devices may be susceptible to interference, which could affect performance.

QUALIFIED SERVICE

Only qualified personnel may install or repair this product.

BATTERIES, CHARGERS, AND OTHER ACCESSORIES

Use only batteries, chargers, and other accessories approved by Nokia for use with thi s device. Do not connect incompatible products.

KEEP YOUR DEVICE DRY

Your device is not water-resistant. Keep it dry.

PROTECT YOUR HEARING

To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise caution when holding your device near your ear while the loudspeaker is in use.

Get started

Keys and parts

1 Neck loop 2 Vibrating alert motor 3Multifunction key 4Microphone 5NFC area 6 USB connector 7 Charging status indicator 8Volume keys 9Power key 10 Bluetooth connection indicator

Charge the battery

1. Connect the charger to a wall outlet.

2. Connect the charger cable to the charger connector.

The charging status indicator shows the progress of the charging, turning from red to yellow and finally to green when the battery is fully charged. Charging the battery fully may take up to 2 hours.

3. When the battery is fully charged, disconnect the charger from the loopset first, then from the wall outlet.

The fully charged battery has power for up to 12 hours of talk time or up to 300 hours of standby time.

Tip: To check the charging status when you're connected to a phone, press the power key. The charging status indicator shows the battery level (red=low, yellow=good, green=full).

When the battery is close to discharged, the loopset vibrates and beeps about every 5 minutes, and the charging status indicator quickly flashes red.

Take the loopset into use

1. If necessary, pull out the neck loop plug.

2. Place the neck loop around your neck, and push the plug in the connector.

3. To switch on, press the power key.

If you haven't paired the loopset with any device before, the loopset vibrates once, and the Blueooth connection indicator blinks quickly.

4. To enter pairing mode, press the multifunction key for about 2 seconds.

The Bluetooth connection indicator flashes steadily. You can now pair the loopset with a phone.

If you have paired the loopset before, the loopset tries to connect to the device that you last paired with. The loopset remembers the last 8 devices that it was paired with. If it doesn't detect the latest one, it tries to connect to the next, and so on.

Switch the loopset off

To switch off, press and hold the power key.

The loopset vibrates twice and the Bluetooth connection indicator stops blinking or flashing.

Pair and connect your loopset with your phone

Make sure your loopset is switched on, and in pairing mode.

1. Activate Bluetooth on your phone, and search for Bluetooth devices.

2. Select the loopset from the list to pair your phone with it.

3. If necessary, enter the passcode 0000.

Your loopset is now paired and connected with your phone. The Bluetooth connection indicator slowly flashes.

When you switch on the loopset the next time, it automatically tries to recreate the latest connection.

Tip: When your loopset is connected to a device, but you need to pair with other devices, you can go back to pairing mode by pressing the multifunction key for about 5 seconds.

If the loopset is not connected to a paired device within about 30 minutes, it switches off automatically.

If the connection is lost, the loopset vibrates and the Bluetooth connection indicator quickly blinks.

Pair and connect your loopset using NFC

If your phone supports Near Field Communication (NFC), you can quickly pair and connect your loopset, or switch the connection between paired devices.

1. On your phone, make sure that NFC is on and the phone keys and screen are unlocked.

2. Make sure the loopset is on and in pairing mode.

3. Tap the NFC area of the loopset with the NFC area of the phone.

4. If asked, accept the connection on your phone. Disconnect or reconnect a paired device

To disconnect a paired and connected device from your loopset, tap the NFC areas together. To reconnect, tap the NFC areas together again.

+ 14 hidden pages