Pulsar
TM
EX20
User Manual
!
…
+
–
…
…
+
…
–
…
%
%
Rack
/ EX30
Rack
www.mgeups.com
Thank you for purchasing the EX
Rack
Uninterruptible Po wer Supply.
The EX
Rack
has been designed to
provide many years of trouble-free
operation. Please review the manual
which has been prepared to provide
you with all the necessary information
concerning the installation and use of
your EX
Rack
.
For service call 1-800-523-0142.
Sincerely,
MGE UPS SYSTEMS
Federal Communications
Commission (FCC) Statement
Note: this equipment has been tested and
found to comply with Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when equipment is operated in
a residential environment. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Properly shielded
and grounded cables and connectors must
be used in order to meet FCC emission
limits.
Pulsar EX
Rack
: 86-153500-00Revision A00 ECN - 000071
MGE UPS SYSTEMS
IMPORTANT SAFETY INSTRUCTIONS
SA VE THESE INSTRUCTIONS
This manual contains important instructions for Models EX20Rack / EX30Rack / EXB20/30 that should be
followed during installation and maintenance of the UPS batteries.
c This equipment can be operated by any
individual, with no previous training;
c CAUTION: Risk of electric shock, even
with unit disconnected from AC power
source. Hazardous voltage still may be
present through operation from battery.
The battery supply should be disconnected
at the plus and minus terminals using the
quick disconnect connectors of the battery
when maintenance or service work inside
the UPS is necessary.
c The UPS contains voltages which are
potentially hazardous. All repairs should
be performed by qualified service
personnel only;
c do not attempt to power the UPS from
any receptacle other than a 2-pole 3-wire
grounded receptacle;
c do not place Pulsar near water or in
environment of excessive humidity;
c do not allow liquids or any foreign objects
to get inside Pulsar;
c do not block air vents in front or back of
Pulsar;
c do not plug household appliances such as
hair dryers to Pulsar receptacles;
c do not place Pulsar in direct sunlight or
close to a heat-emitting source;
MGE UPS SYSTEMS
c the AC power receptacle should be near
the equipment and easily accessible. To
isolate Pulsar from AC input, remove the
input power cord from the AC power
receptacle;
c if Pulsar is to be stored for a long time, it
is recommended to recharge the batteries
(by connecting AC power source to Pulsar,
switch "ON" or "OFF"), once a month for 24
hours to avoid a full battery discharge;
c Pulsar contains batteries that should be
disposed of or recycled in accordance with
local applicable laws;
c prior to installation, store Pulsar in a dry
location;
c storage temperatures must be between
–4°F (-20°C) and +113°F (+45°C);
c servicing of batteries should be performed
or supervised by personnel knowledgeable
of batteries and the required precautions.
Keep unauthorized personnel away from
batteries;
c when replacing the batteries, use the
same number and the following type of
batteries:
v Pulsar EX20
v Pulsar EX30
c ~ : alternating current supply symbol;
Pulsar EX
Rack
: 8 x 12V - 7.2Ah,
Rack
: 8 x 12V - 7.2Ah;
Rack
: 86-153500-00
c CAUTION: do not dispose of battery or
batteries in a fire. The battery may explode;
c CAUTION: do not open or mutilate the
battery or batteries, released electrolyte is
harmful to the skin and eyes. It may be toxic;
c CAUTION: a battery can present a risk of
electric shock and high short circuit current.
The following precautions should be
observed when working with batteries:
v remove watches, rings or other metal
objects,
v use tools with insulated handles,
v wear rubber gloves, boots and safety
glasses;
c please dispose of the packaging in
accordance with applicable laws.
i
introduction
In critical situations, count on MGE UPS
SYSTEMS Pulsar EX20
EX30
Rack
uninterruptible power supplies
(UPS). Their protection keeps your data
intact and accessible.
Pulsar EX20
Rack
ensure top quality power around the clock,
and continue operations during power
failures. An intelligent microprocessor
detects any operating anomalies of the UPS
and triggers an alarm if corrective action is
necessary.
In addition to the high-technology aspect of
these UPSs, you can count on backup from
our staff, a team of specialists, around the
corner from you, throughout the world. It’s
no accident that MGE UPS SYSTEMS is the
world leader in UPS protection. The UPS
provides power factor correction to reduce
harmonic distortion and current created by
non-linear critical loads from polluting the
incoming AC line.
UPS includes:
c batteries,
c power factor correction / battery charger,
c DC to DC converter,
c DC to AC inverter,
c bypass switch,
c input/output filters.
The MGE Pulsar UPS is capable of
providing the following modes of operation:
c ON LINE MODE which is the primary
mode of operation in which the critical load
is continuously supplied by the inverter and
protected from all forms of power line
disturbances:
Rack
and EX30
and
Rack
UPSs
AC
IN
EMI
filter
power
factor
corrector
rectifier
charger
DC / DC
micro
control and
DC to AC
inverter
monitored
batteries
critical
system
c BYPASS MODE which is a default mode
in the event of an inverter failure or overload
in which the critical load is supplied AC
through EMI/RFI filter:
AC
IN
EMI
filter
power
factor
corrector
rectifier
charger
DC / DC
uses of Pulsar EX20
EX30
Rack
:
micro
control and
DC to AC
inverter
monitored
batteries
Rack
and
critical
system
Network servers and interconnection
devices are very sensitive to electrical
disturbances of all types, including outages,
voltage sags, brownouts, spikes, etc. The
origins of the disturbances also vary, ranging
from atmospheric phenomena, to nearby
devices generating interference such as
elevators, photocopy machines and machine
tools, not to mention human errors, like the
accidental pulling out of power cords or
tripping of circuit breakers. The
consequences of these disturbances on
computer systems range from data losses to
hardware damage (power supplies, hard
disks).
Pulsar EX20
Rack
and EX30
Rack
are
specially designed to protect network
servers and all other interconnection devices
that are sensitive to electrical disturbances.
Pulsar EX20
Rack
and EX30
Rack
add faulttolerance to the utility supplying your
sensitive equipment.
Pulsar EX20
Rack
and EX30
Rack
are
designed as compact units and feature very
quiet operation.
Pulsar EX20
Rack
and EX30
Rack
provide a
stable supply of clean power, long back-up
time during a utility outage (see table) and
vast information and control possibilities
according to the configuration selected.
Pulsar EX20
Rack
and EX30
Rack
On-Line
technology provides maximum protection
and availability of workstations, servers, and
network communication devices.
Pulsar EX20
Rack
and EX30
Rack
offer
many functions and characteristics designed
to simplify power management:
c automatic battery test carried out
periodically. In the event of a fault, a LED
provides advance warning for battery
replacement;
c front panel LEDs signal all types of faults
and alarms;
ii
Pulsar EX
Rack
: 86-153500-00 MGE UPS SYSTEMS
c Bar graph continuously indicates the
battery charge level or the critical load power
level;
c Pulsar EX20
environment friendly: all components are
recyclable and an electronic power-saver
device reduces power consumption if the
UPS is not active for a period exceeding 5
minutes while on battery back-up;
c EX Driver software provides rapid startup
of Pulsar EX20
the EX Tuner configuration module. This
module adapts Pulsar EX20
EX30
Rack
frequency, startup and shutdown
sequences, setting of battery thresholds,
etc.). See "communication" section for
further details;
c Solution-PacTM is a CD-ROM which
contains all the tools needed to supervise
your UPS.
c Simply download the EX driver utility from
the CD and Solution-Pac. The UPS must be
serialy connected to a Windows PC.
Rack
and EX30
Rack
and EX30
to user preferences (battery test
Rack
Rack
Rack
are
using
and
options
c UM Sensor environment measurement
unit: compatible with SNMP or Solution
PacTM, this unit measures the temperature
and the relative humidity in the room where
the Pulsar is installed. Eight relay contacts
are provided to transmit signals to an
administration platform, in the form of
voltage-free contacts to enable monitoring of
(fire alarm, climate control fault, intrusion,
etc.);
c battery extension module: Pulsar
EXB20/30 battery extension modules
lengthen the battery time of the Pulsar
EX20
Rack
/EX30
Rack
requirements. For rack installation of EXB20/
30 order 19" rack kit P/N 8907U.
c output transformer: input line cord plugs
into the Pulsar EX30
receptacle. Rating is 120V AC input, 208V/
240V AC 2.75 kVA output;
c maintenance bypass switch: enables
the user to continue supplying ac power to
the load while performing routine or
emergency maintenance.
to meet your
Rack
output
additional communications
options:
c SNMP administration: MGE has the
most complete offering for the administration
of a group of UPSs using the SNMP protocol
with different network-connection modules
(SNMP card or proxy software), supervision
modules (application for NMS platforms
such as HP OpenView or C.A. UNICENTER
TNG) and a file-closing module (UM Client).
c SNMP card: this card, inserted into your
unit, can establish a direct Ethernet network
connection for your UPS. It can then be
temporarily managed using SNMP or the
various software modules of Solution-Pac.
The MGE UPS SYSTEMS offering complies
with RFC 1628 specifications (IETF) and
was certified by the InterWorking Labs
during the Test Summit in June 1994;
c status information card: this option
provides you with 5 voltage-free contacts: on
battery, on by-pass, low battery, load on
UPS. This card can be used with the UPS
driver of IBM AS/400.
Contact your dealer for further information
on these options.
MGE UPS SYSTEMS
Pulsar EX
Rack
: 86-153500-00
iii
software supplied with
Pulsar EX20
EX30
Rack
To meet the different operating
environments of your UPS, Pulsar EX
includes 2 MGE UPS SYSTEMS software
programs:
c EX-Driver software for Windows
c Network based Solution-PacTM power
management software
EX-Driver for Windows
EX Driver for Windows provides
communication with the UPS from a simple
Windows workstation. EX-Driver is
compatible with Windows 3.1x and Windows
95/98, for communication with the UPS via a
serial connection for various needs:
c personalization of the UPS operating
mode: the EX-Tuner utility, can be used to
change certain UPS operating parameters if
the standard factory settings are not ideal for
the operating conditions.
It is possible to modify the output voltage,
battery-test frequency, startup and shutdown
sequences, operation of automatic by-pass,
etc.;
Rack
and
Rack
Solution-PacTM for networks and
multi-server systems
Protection by UPS is only complete and
effective if combined with powerful software
functions which warn users and the operator
of any power supply problem, automate
system shutdown, supervise and remotely
control the UPSs. MGE UPS SYSTEMS
created Solution-PacTM for this purpose.
Solution-PacTM combines all these functions
in a single CD-ROM, usable in local or
remote mode (TCP/IP and SNMP), and
covering the main network environments.
Solution-PacTM is the ideal solution for
protecting networks and multiserver
systems.
Solution-PacTM on a single CD-ROM
contains everything needed to safeguard
one or more systems and to supervise one
or more UPSs from a local or remote station.
Solution-PacTM includes SNMP proxy
agents, system shutdown software, and
supervision software.
Solution-PacTM is a powerful and upgradable
software tool which provides all the
supervision, control and safety functions
associated with a UPS:
v graphic display of the UPS,
v remote control of the UPS and output
receptacles,
v user alarm of problems,
v recording of events in log files,
v automatic system shutdown and restart,
v local or remote supervision of UPSs and
ancillary devices,
v transmission of UPS information and
alarms to any SNMP supervisor.
v paging / e-mail capabilities
v multiple server shutdown in
heterogeneous environment.
Platforms supported:
Windows 3.1, 95, 98, NT, Novelle Netware,
OS/2, Linus, Mac/OS, Sun Solaris, HP/UX,
IBM Aix, Dec Unix and Open VMS, Silicon
Graphics, IRIX.
iv
Pulsar EX
Rack
: 86-153500-00 MGE UPS SYSTEMS
general contents
Pulsar presentation............................................................................................................................. 3
getting started / operation....................................................................................................... 11
Pulsar EX20
Rack
/ EX30
Rack
/ EXB20/30 presentation
MGE UPS SYSTEMS
Pulsar EX
Rack
: 86-153500-00
1
MGE UPS SYSTEMS
Pulsar EX
Rack
: 86-153500-00
2
7b
5
7a
9
12
11
10
7c
6
13
8
7a
Pulsar EX20
front view
Rack
/ EX30
Rack
Pulsar EX20
rear view
Rack
1f
1e
1c
2
!
+
–
3
%
+
–
…
…
%
…
…
…
1a
1b
1d
3
Pulsar EX
Rack
: 86-153500-00
MGE UPS SYSTEMS
4
Pulsar EX
Rack
: 86-153500-00
MGE UPS SYSTEMS
Pulsar EX30
rear view
Rack
8
11
MGE UPS SYSTEMS
13
6
9
Pulsar EX
Rack
: 86-153500-00 5
5
7c
7b
7a
12
10
Pulsar EXB20/30 Extended Battery (See options for battery extension module on page iii.)
rear view
19
21
20
PLACE
STAMP
Volt: 96Vdc == 20A
Volt: 96Vdc == 20A
CIRCUIT
BREAKER
120Vdc/40A
22
MGE UPS SYSTEMS
ATTN: CUSTOMER SUPPORT SERVICES
1660 SCENIC AVENUE
COSTA MESA, CA 92626
HERE
14
The indispensable
companion
sofware
for your UPS
L'indispensable
complément
logiciel
de votre onduleur
18
solution-pac 98
23
6
Pulsar EX
Rack
: 86-153500-00 MGE UPS SYSTEMS
17
key to diagrams
yellow indicator LEDs 1a to 1d flashing
quickly:
1a overload,
1b device fault,
1c battery fault,
1d operating on bypass (fault tolerant
mode),
yellow indicator LEDs 1a to 1d
continuously or flashing slowly: indicate
the battery charge level (if utility power
present) or remaining battery time (if no
utility power present). They may be on
continuously or flash slowly during a
transition period. By pressing the button
marked "function" 2 when utility power is
present, they indicate the load charge level.
1e green indicator LED flashing: operating
on battery,
1f green indicator LED on continuously:
load powered by UPS,
green indicator light off: load no
powered by UPS,
2 "function" button: switches off audio
warning device or measures load
charge percentage (if utility power
present),
3 "ON/OFF" switch:
button pushed in: ON
button not pushed in: OFF,
5 attached input cord,
6 input circuit breaker:
20A/125V for Pulsar EX20
30A/125V for Pulsar EX30
L5-20 EX20R, L5-30 EX30R,
7a twist-lock output receptacle for
connection of computer loads to Pulsar
EXR,
7b output receptacles rated each 15A,
7c Pulsar EX20
to protect each 7b output receptacles,
Pulsar EX30
reset circuit breakers to protect each
7b output receptacles,
8 site wiring fault LED,
9 rating label,
10 fans,
Rack
Rack
Rack
,
Rack
, -
: T 15A/120V fuses
: 15A/120V push to
11 SUB-D 9 pin connector for U-Talk
RS232 communication port,
12 cover for optional communication cards,
13 connector for Pulsar EXB20/30 battery
extension module,
14 warranty card,
17 Solution-PacTM CD-ROM, EX Driver
18 RS232 cable,
19 Pulsar EXB20/30 battery extension
module,
20 battery circuit-breaker,
21 connector to Pulsar EX20
EX30
Rack
,
22 connector for second Pulsar EXB20/30
battery extension module,
23 battery connection cord.
Rack
/
MGE UPS SYSTEMS
Pulsar EX
Rack
: 86-153500-00 7
technical data
c output power:
v Pulsar EX20
v Pulsar EX30
c input voltage:
v voltage (V): a 90V to 138V single phase (70V to 138V at 1/3 Power, 80V to 138V at 2/3 Power)
v frequency (F): 47Hz to 53Hz or 57Hz to 63Hz
c battery:
v type : maintenance free sealed lead-acid, 8 x 12V - 7.2Ah
caution: battery life (4 or 5 years) is halved every 10°C above 25°C
c output specifications:
v voltage (V): single phase 120V ± 3% (can be adjusted from 100 to 127V using EX Driver)
v frequency (F): 50/60Hz ± 0.5% (frequency configuration using EX Driver)
c environment:
v noise level: ≤ 50dBA for operation on utility power
v operating temperature: 0 to 35°C
v relative humidity: 0 to 90%
c dimensions and weights: Pulsar EX20
v height H (inches): 5.12 5.12
v width W (inches): 19 19
v depth D (inches): 21.75 21.75
v weight lbs (kg) : 88(40) 92(42)
Rack
: 2000VA/1400W
Rack
: 3000VA/2100W
+
–
a
/ a
+
–
/
D
≤ 50dBA for battery backup mode
non condensing
H/3U
W
Rack
Pulsar EX30
Rack
8
Pulsar EX
Rack
: 86-153500-00 MGE UPS SYSTEMS
Pulsar EX20
Rack
battery back-up time
3000 VA
1500 VA
750 VA
0 1 2 3 4 5
Pulsar EX30
2000 VA
1500 VA
1000 VA
500 VA
0 1 2 3 4 5
Rack
battery back-up time
t (hours)
t (hours)
Pulsar EX30
Rack
alone
Pulsar EX30
Rack
Rack
Rack
Rack
Rack
alone
+ 1 Pulsar EXB20/30
Pulsar EX30
+ 2 Pulsar EXB20/30
Pulsar EX20
Pulsar EX20
+ 1 Pulsar EXB20/30
Pulsar EX20
+ 2 Pulsar EXB20/30
MGE UPS SYSTEMS
Pulsar EX
Rack
: 86-153500-00 9
10
Pulsar EX
Rack
: 86-153500-00 MGE UPS SYSTEMS
contents
getting started ..................................................................................................................12
location......................................................................................................................................12
preliminary checks ....................................................................................................................12
connections ............................................................................................................................... 12
communication .......................................................................................................................... 13
operation ............................................................................................................................. 14
starting up with utility power present ......................................................................................... 14
starting up with out utility power ................................................................................................ 15
operation on battery .................................................................................................................. 16
overload .................................................................................................................................... 17
operating anomalies..................................................................................................................17
MGE UPS SYSTEMS Pulsar EX
Rack
: 86-153500-00
11
getting started
location
c observe the safety rules indicated at the
beginning of this document.
preliminary checks
c check that the "on/off" button " " on the
front is not pushed in;
c check that rating shown on the rating label
corresponds to the input voltage
specification and power requirement of the
load.
connections
c connect the AC input cord to the utility
power outlet.
EX 20
Rack
utility power
receptacle
7a
computer
loads
5
7b
EX 30
Rack
utility power
receptacle
7a
computer
loads
5
7b
Note 1: following connection, the battery
automatically charges, whenever plugged in.
Note 2: the batteries will provide full back-up
time after approximatively 8 hours of
recharge time.
Note 3: if site wiring fault LED 8 is lit and
audible alarm sounds, line/neutral
connections are reversed.
c connection of the Pulsar EXB20/30
battery extension module (optional):
v check that the button "on/off" " " on the
front of the Pulsar EX20
Rack
/EX30
Rack
is
not pushed in,
v disconnect the input connection cord,
v flip the circuit-breaker of the battery unit to
the right (position "O"),
v connect the battery connection cord to the
DC connector of the battery module and
connect to the Pulsar EX20
EX30
Rack
,
Rack
/
v if the installation has 2 battery modules,
connect the second cord to the DC
connector of the second module and to the
first module,
v the use of connectors is strictly limited to
connecting the battery modules to the
Pulsar EX20
Rack
/EX30
Rack
. Any other
connection to these connectors is prohibited
and risks damaging the battery, not covered
by warranty,
v to start, flip the battery circuit-breaker to
the left (position "I"),
v if your installation is operated with MGE
UPS SYSTEMS software, update your
battery configuration with EX Tuner.
c connect the computer loads to output
sockets 7a or 7b .
12 Pulsar EX
Rack
: 86-153500-00 MGE UPS SYSTEMS
communication
c the U-Talk communication port, at the rear
of the Pulsar, delivers information in the
form of an RS232 series link supported by
the communication protocol exclusive to
MGE UPS SYSTEMS.
The Solution-PacTM programs use the data
made available by this protocol.
standard port
0V
RD TD
5432
9876
1
11
option 1
c status information card: after the card is
installed in the rear of the Pulsar,
communication port transmits the status
information on a SUB-D 9-pin female
connector using the following pinouts:
1- ground,
2- remote power off,
4- normal operation,
5- common,
6- operation on utility power,
7- low battery warning,
8- load supplied by UPS,
9- operation on battery.
0V
Note for remote power off information:
Remove first J1 jumper on the status
information board, then link your remote
power off switch S1 between pins 2 and 5.
Follow instructions from user's manual of the
optional board for installation.
c switch ON: normal operation,
c switch OFF: unit stops immediatly.
5432
9
1
876
12
With the EX Driver software program you
can set up Pulsar EX
Rack
to suit your user
conditions (EX Tuner). To install EX Driver,
connect the serial cable supplied to COM1
to COM4 (set up by EX Tuner) serial port of
n.c.
n.o.
your computer equipped with Windows 3.1
or 95/98 on the one end, and to the serial
Pulsar EX
Rack
connector on the other end.
0V
Insert the CD and type A:\Install. Follow the
installation instructions on the screen.
MGE UPS SYSTEMS Pulsar EX
Relay breaking capacity:
Vmax = 25V DC
Imax = 10mA
n.o. : normally open,
n.c. : normally closed.
5432
9
876
n.o.
0V
Rack
: 86-153500-00
1
n.o.0Vn.o.
0V
12
S1
option 2
c SNMP card: after the card is installed in
the rear of the Pulsar, the communication
port transmits information supported by the
TCP/IP and SNMP protocols on an RJ45
connector to any Ethernet network.
Contact your sales agent for further details.
13
operation
starting up with utility power present
indicator lights testpress button "on/off" :
automatic sequence:
1 s beep
output off output off
several beeps
14 Pulsar EX
device and battery test
indicating the
remaining battery
time percentage
(here 50%)
silence
your load is supported
by the battery
Rack
: 86-153500-00 MGE UPS SYSTEMS
normal operation
17 s7 s5 s0 s
indicating the
recharge
percentage of the
battery (here 50%)
silence
UPS is on utility power
starting up with out utility power
indicator lights testpress "on/off" button:
automatic sequence:
1 s beep
output off output off
MGE UPS SYSTEMS Pulsar EX
several beeps
device and battery test
your load is supported
by the battery
Rack
: 86-153500-00
indicating the
remaining battery
time percentage
(here 50%)
3 s beep
normal operation on battery
17 s7 s5 s0 s
indicating the
remaining autonomy
percentage
(here 50%)
1 beep every 10 s
UPS is on utility power
15
operation on battery
no utility power
break in utility power
indicating the
remaining battery
time: here, between
75 and 87%
1 beep every 10 s
your load is supported
by the battery
warning alarm at low
battery
x mn0 mn
1 beep every 3 s
you have less than 12% battery time
remaining: power down your load, Pulsar
will soon switch off automatically
Pulsar switches off
automatically
x + ε mn
silence
UPS output "off"
return of utility power load charge percentage
At whatever point the utility power
returns, Pulsar switches to normal
operation:
silence
indicating the battery
recharge percentage:
here, between 12 and
25%
Note 1:
The "function" button is to deactivate or
activate the audio warning device when
operating on battery, or when site wiring
fault occured.
Note 2:
The "function" button allows you to force a
transfer on bypass (push three times within
5 seconds) and to come back on normal
operation (push again three times within 5
seconds).
If utility power is present, hold alarm
silence button in:
silence
indicating the load
charge percentage:
here 50%
your load is supplied by the utility power
(on line)
16 Pulsar EX
Rack
: 86-153500-00 MGE UPS SYSTEMS
overload
utility power present
1 beep
every
second
operating anomalies
device fault
1 beep
every
second
battery fault
A battery test is carried out while Pulsar, is in
start-up mode, then automatically every 7
days (interval times adjustable using EX
Driver). If a battery fault is detected, the
following occurs:
vv
v automatic load transfer to bypass,
automatic load transfer to bypass
no utility power present
vv
vv
v switch off Pulsar (release "on/off" button),
vv
disconnect from the wall socket (check input
cord), and check that Pulsar has not shortcircuited (disconnect all loads),
vv
v if necessary, change one of the fuses 7c ,
vv
vv
v re-start Pulsar.
vv
battery low
1 beep
every
second
Pulsar switches off automatically after a
length of time which depends on the level
of overload.
Note: overload occurs if the load
consumption is greater than the rated power
of Pulsar.
To acknowledge the fault, release the "on/
off" button, temporarily disconnected Pulsar
from the wall socket (check input cord),
disconnect loads and re-start Pulsar.
MGE UPS SYSTEMS Pulsar EX
after the start-up sequence, if the audio
warning device sounds continuously,
recharge your battery for 8 hours.
Note: if the previous symptoms persist,
contact technical support.
Rack
: 86-153500-00
continuous
beep
1 beep
every
second
recharge your battery for 8 hours.
operation on bypass
…
1 beep
every
second
see "overload" and "device fault" section
Note:
This operating mode provides temporary
inverter fault tolerance.
17
18 Pulsar EX
Rack
: 86-153500-00 MGE UPS SYSTEMS
service and factory repair - call 1 - 800 - 523 - 0142
c direct questions about the operation, repair, or servicing of this equipment to MGE UPS SYSTEMS, Inc. Customer Support Services. Include
the part number, and serial number of the unit in any correspondence. Should you require factory service, contact MGE UPS SYSTEMS, Inc.
Customer Support Services and obtain a Return Materials Authorization (RMA) prior to shipping your unit.
proprietary rights statement
c the information in this manual is the property of MGE UPS SYSTEMS, Inc., and represents a proprietary article in which MGE UPS SYSTEMS,
Inc., retains any and all patent rights, including exclusive rights of use and/or manufacture and/or sale. Possession of this information does not
convey any permission to reproduce, print, or manufacture the article or articles shown herein. Such permission may be granted only by specific
written authorization, signed by an officer of MGE UPS SYSTEMS, Inc.;
c Trademarks that may be used herein are owned by their respective companies and are referred to in an editorial fashion only.
two years warranty policy
c MGE UPS SYSTEMS, Inc. (herein after referred to as MGE) warrants Pulsar equipment manufactured by MGE to be free from defects in
materials and workmanship for a period of two years from date of purchase. If within such period purchaser discovers defective item and promptly
notifies MGE in writing, MGE shall repair or replace the item at the Company's option. This warranty shall not apply:
v to equipment not manufactured by MGE,
v to equipment repaired or altered by others than MGE,
v to equipment subjected to negligence, accident, or damage by circumstances beyond MGE's control, or to improper operations, maintenance,
or storage, or to other than normal use or service.
With respect to equipment not manufactured by MGE, the Warranty obligations of MGE shall in all respects conform and Warranties do not cover
reimbursement for labor, transportation, removal, installation, or other expenses which may be incurred in connection with repairs or replacement.
Except as may be expressly provided in an authorized writing by MGE, MGE shall not be subject to any other obligations or liabilities whatsoever
with respect to equipment manufactured by MGE or service rendered by MGE.
MGE UPS SYSTEMS
Pulsar EX
Rack
: 86-153500-00
MGE UPS SYSTEMS, Inc.
www.mgeups.com
86-153500-00
Postal address:
1660 Scenic Avenue
Costa Mesa, CA 92626
714-557-1636
Loading...