MFJ MFJ-9200 troubleshooting guide

MFJ-9200 Ops /Maint Manual 08/25/2017

A Guide to

Operating,

Troubleshooting and Repair

of the

MFJ-9200 QRP Radio

by

Donald E. Koehler

KL7KN

Copyright 2014-2017

All Rights Reserved

1

MFJ-9200 Ops /Maint Manual 08/25/2017

Foreword from the author:

These are the new "golden years" of ham radio, with newly licensed operators swelling the ranks daily.
One thing I have noticed is that a significant number of these new hams have no background in
radio/electronics. Thanks to the Internet and many sites that provide a focus on passing the Amateur
Radio Service FCC tests, these new hams have a license but no
works.

real

knowledge of how the technology

I don't say this like it's a bad thing, because
entering this hobby have no clue on how to perform basic troubleshooting of on repair of the radios they
use in enjoying the hobby. To be honest, some of the newer radios on the market, especially handheld
V/UHF rigs are, frankly, disposable. It has become, quite literally, less expensive to purchase a
replacement radio than to attempt repairs via a commercial shop where shop rates can reach $100/hour.

On the other end of this equation, is the MFJ-9200 QRP Transceiver.

This radio is an
ultimate in a Plug and Play rig. Add power, a resonant antenna, a set of cans, a key and you have a
working
prior to purchasing this radio, I discovered that neither the Chinese manufacturer or the Seller has made
technical data for the rig publicly available.

This situation is a common issue with many radios imported to North America. Repair of the unit
becomes problematic for a new or inexperienced operator and even experienced hams need at least
some technical data and a parts list prior to attempting a repair.

I wrote this manual with the view of the new ham trying to fix what are the most likely problems with a
dead radio, quite literally, on the kitchen table with very minimal equipment. The Manual covers the
most common items that might need repair in the lifetime of the rig. I later added a modified Operations
manual, hopefully one a bit easier to understand.

I hope you enjoy this Guide and welcome any suggestions to improve this Guide for everyone enjoying
the MFJ-9200. Many of the
rigs, like the HB-1Bx.

I've sent many copies of this manual out to the amateur community as requested. To my surprise, Steve
Weber (
9200 and he was kind enough to draw up a full schematic for the unit and kindly allowed me to include
it. Thanks Steve! I'm certain many will remember your support to the QRP community.

multi-band

Yes

excellent

little HF rig and offers quite a lot to the portable operator. It is, to me, the

HF station. Set the frequency, and you're on the air. Unfortunately, in my research

troubleshooting

, that Steve Weber, KD1JV) asked for a copy. Long story short, I shipped him a working -

it is not

tips and tricks will work with any of the newer solid state HF

. What it

does

mean is that a large number of folks

Another happy side effect to sending out many copies of the manual is the feedback I receive from other
hams. This manual is the fourth version and as I obtain more data, updates will follow.

August 25, 2017

Don//KL7KN

Anchorage, Alaska.

08/23/2017 Happy Face – the rig is listed again and is back in stock with the folks at
MFJ.

2

MFJ-9200 Ops /Maint Manual 08/25/2017

About the Author:

Mr. Koehler first tested for and received his FCC Commercial Radiotelephone license
with a RADAR endorsement in 1977. He received his Amateur Radio Service license on
the next test cycle. This was back when FCC employees had to give the test.

After spending 22+ years in the US Air Force as a Master Technician working on
radio/electronics, maintaining a wide variety of communications equipment to the
component level, Mr. Koehler retired from the military. He then went on to spend
another 10 years working with telecommunication equipment as a technician, technical
writer, quality manager and finally, a supervising manager.

He now works part-time as a technical writer for a local Corporation in the IT field. His
published works include many articles in "73" Magazine, Site (later, Above Ground
Level) Magazine and multiple other industry periodicals. He was also a Contributing
Editor for Mobile Radio Technology magazine for a number of years.

He has a Bachelor of Science degree from the University of the State of New York, with
multiple Associate degrees, to include an Associate of Science in Communications
Technology.

In addition to HAM radio, he enjoys shortwave listening, sailing, hiking, camping and
just being outdoors in Alaska. A prolific fiction writer, he has ten full length novels
currently on the market under a pseudonym. (see www.worldofthechernyi.com)

Steve

"Melt Solder"

Weber, KD1JV, who provided the attached schematic, is well known

for his QRP designs. See more of his work at kd1jv.qrpradio.com.

To retain the fidelity of the original drawing by Steve, I send that as a separate .PDF file
with just the schematic. This will allow you to 'zoom in' as need to see details.

3

Table of Contents

Operations Manual

1. How to Use this Guide

 Recommended tools and Test equipment:

Describes minimum tools & test equipment required to use this manual.

2. Warnings page

3. Basic radio overview / Concept of Operations:

3.1. Radio Overview.

3.2. DC power busses and protection

3.3. Voltage regulation

3.4. DDS VFO sub-system

3.5. Band Module diagram and header pin-outs

3.6. Receiver

3.6.1. Signal path.

3.6.2. Filtering scheme.

3.6.3. Audio switching, muting and sidetone .

3.7. Transmitter

3.7.1. Signal path.

3.7.2. SWR protection for final amplifier.

4. Troubleshooting Basic Radio Problems:

4.1. Radio does not turn on.

4.2. No received signal is heard.

4.3. No RF output/Low RF output

4.4. No or low audio output

4.5. Radio doesn't key or keys erratically

4.6. Display is dead, displays "funny characters" or has no backlight

4.7. Radio is off frequency (display doesn't match measured output signal)

5. Sub-system or specific component Tests

5.1. DDS function

5.2. 60 MHz Master Clock

5.3. Adjust VR for +5VDC

5.4. BFO function

5.5. First Mixer

5.6. Second Mixer

5.7. Audio Path

5.8. Phones jack

5.9. Bypass Band Module

5.10. Test Q10 with Ohm meter

4

Table of Contents

Basic Maintenance and Repair of the radio

Tuning Band Modules for best performance.

Remove main circuit board from chassis to access both sides of system board

Install main circuit board back into chassis

Minimum checks before power up after maintenance

Replacement of DC feed protection diode

Replacement of Q10 (transmitter final)

Replacement of DDS encoder

Replacement of display screen

Replacement of Volume potentiometer

Illustrations

Data for system components

Hints, Tips, Kinks

Recommended items not supplied with radio set

Building a portable DC power system

The genesis of the 9200

A schematic for MFJ-9200 is sent separately as a .pdf file to allow full screen viewing.

This Guide is focused on the new amateur population providing simplified:

 Diagrams of important systems and sub-systems.
 Troubleshooting and maintenance steps that may be taken with minimal test

equipment. I explain how to use the listed test equipment and how to build
some of your own.

 A

limited

point in the life of the radio set. I'll explain
hopefully allow you to get your rig up and running.

 I also provide at least one source (available at the time of this writing) and

common part numbers to source the parts for yourself in the future.

parts listing for those items

most likely

how

to need replacement at some
to replace those parts and

Please note the list of parts; part numbers and parts source were current at the time
this was written.

5

MFJ-9200 Operating Instructions – modified.

In reading many of the E-mails sent to me with regard to my original Technical
Manual, it has become apparent that some form of simplified Operating instruction
should have been included. While MFJ's on-line Operating Instruction is adequate, it
may be confusing to a new ham. I found a very well done manual for the HB-1A on­line written up by K9MA, Scott Ellington. I asked for and received his kind permission
to edit his basic layout (format) over to -9200 specifics for use in this manual section.
Photos used with permission.

Warning

manual

result in permanent damage to your radio!

Initial power up

After connecting a known good antenna or dummy load, key, headphones and then the
power supply, turn the radio on. After the initial splash screen shows the installed Band
Module, the -9200 LCD panel displays:

6

: Before attempting to operate your MFJ-9200 on air,

. Failing to adhere to prescribed setup and operating recommendations could

Operating Mode (CW/USB/LSB)
(M) Memory number or (V) VFO this setting is based on last use.
Supply Voltage (xx.x VDC) displays alternatively with the Mode.
Receiver Incremental Tuning (

just after the displayed frequency – with a dash or up/down arrow (  ) .

RIT

) status and amount of offset is provided

read through the entire

VFO Tuning Steps:

The VFO tuning steps are set by pressing down on the Tune control. Press briefly to
change between 100 HZ and 1 KHz. (Observe location of flashing digit)

For 100 KHz increments, press and hold Tune for several seconds. (Observe location
of flashing digit)

RIT Steps: 10-Hz default
VFO Memories: 8 per band
VFO Display: LCD, switched backlight
VFO Display Frequency Resolution:

100-Hz, 10-Hz with RIT activated.

Operating Modes:

Transmit - A1 (CW) only, Receive - A1, A3J (LSB or USB) Am is possible with careful
tuning.

CW Offset: ~700 Hz
T/R Switching: Fully QSK capable

External Power Supply

Any 9 to 14.8 V DC power supply or battery may be connected to the radios coaxial
power jack, provided that any internal battery is disconnected. Reverse-polarity
protection at the main DC input and the internal J2 power header is provided. There is
no internal battery charger.
against an operator installing an internal battery. (See battery section for more)

Antenna

Any well-matched (50 Ohm) antenna may be connected to the ANT jack BNC
connector. An external antenna tuner is required for antennas which are not resonant
at the selected frequency. The radio does not provide for any adjustments other than
audio volume and VFO. High SWR
antenna.

Headphones

A stereo headset can be connected to the PHONE jack. Impedance should be 8-32
Ohms. A
output! Alternatively, you may use a mini stereo amplified speaker. While 8-32 ohms is
recommended, a 4 ohm stereo speaker will work – just barely.

NOTE: As noted in

Modules

on the AC setting, tune your band modules! If you choose to use an amplified speaker
for tuning, bypass the amplifier and connect to the speaker itself.

stereo

connector

Basic Repair and Maintenance

, if you have access to the speaker leads, you may, with a sensitive multi-meter

No

internal battery was ever offered. I also recommend

will

damage the radio. Use care when tuning any

must

be used. A MONO headphone plug will SHORT the

of the radio, under the

Tuning Band

Key/Paddle

If using a stereo plug for a straight key, both ring and sleeve must be connected
together for use. A monaural plug may also be used with a straight key.

7

TIP. Connects to DOT paddle or straight key

RING. Connects to DASH paddle or straight key ground

SLEEVE. Connects to paddle or straight key ground

Key Operation

When power is applied with a paddle connected or no key is present, the letter “A” will
be heard in the headphones upon power up. The letter “M” is heard if a straight key is
connected.

Mem/VFO Button

Pressing this button alternates the display between Memory mode (M) and VFO
(V)mode. The display will show M-# or V-#. # represents the numbers 1 thru 8.

In Memory mode, the Tune knob is used to change memory locations.
In VFO Mode, the Tune knob is used to change the frequency.

Pressing and then holding the Mem/VFO key for more than two seconds will display
SAVE \ and the current frequency and mode will be stored in the memory # location
displayed.

Band Error: If no filter module has been installed, the display will flash [BAND-???]
to alert you that a module must be installed for the radio to operate.

Transmit Error: If the transmitter is keyed while the VFO is tuned outside the amateur
band, the top line of the display / flashes [TX ERROR] and transmission is blocked.

TIP - Setting the radio to an out of band frequency will allow the operator to practice
sending with a new key or set of paddles. This is also a good time to set keyer speed.

8

RIT/MODE Button

RIT Mode:

Press this button briefly to enter or exit the RIT function. A dash (==) will be displayed
to the right of the frequency.

In the RIT mode, the Tuning knob controls the offset of the received frequency from
the transmit frequency. The transmit frequency setting is unchanged. The dash (==)
indicates that the received frequency is the same as the transmit frequency (zero
offset).

NOTE – Remember that the normal offset of ~750 Hz is always present.

Turning the Tune knob clockwise
arrow ().

raises

the received frequency, as indicated by the up

Turning the Tune knob counter-clockwise
by down arrow ().

In each case,
frequency is not changed. After exiting the RIT mode, the receiver offset returns to
zero.

CW/USB/LSB Mode Changes:

To change mode, press and hold RIT/MOD for two seconds. Press and hold RIT/MOD
for two seconds for each change in Mode.

Changing the Frequency Tuning Steps

The VFO tuning steps are set by pressing down on the Tune control. These steps are
in 100 Hz, 1 KHz, and 100 KHz increments for the amateur bands. Outside of the North
American amateur bands, VFO tuning remains the same. RIT tuning can
in 10 Hz increments.

CW Keyer

Changing Speed:

Press and hold Call button for approximately one second, until the letter “S” is heard,
then release. Within FIVE seconds, press the DOT paddle to increase the keyer speed,
or the DASH to decrease. When done, press Call briefly to exit. The letter “E” is heard.
The 9200 does not give any indication of speed setting in WPM, you can hear
the change in speed, adjust to your comfort level in receiving.

the displayed frequency is the received frequency –

lowers

the receive frequency, as indicated

the transmitter

only

be set

9

Entering Your Callsign:

Press and hold Call button until the letter “S” is heard, continue to hold Call until you
hear the letter “I”, then release the button.

Send your callsign with the paddle as usual. When complete, press Call briefly to exit.
(The letter “E” will be heard.) Otherwise, automatic exit will occur after 8 seconds.

Automatic CQ

Press Call button briefly to send “CQ CQ CQ DE (your callsign three times) PSE K” To

cancel

the PSE – the text is embedded in the chip program. I often suggest an external keyer
for both convenience and memory based messages. This is the same
chip/programming found in the HB1B, -B and the CRK-10A (by BA6BF) radios.

If a straight key is connected, simply close the key to transmit.

the CQ, press and hold Call button for 1 second. It is not possible to eliminate

Test Carrier:

Depress and hold

When you hear T, release the CALL button and press the
continuous carrier. Press the
mode,

The
SWR readings or make tuner adjustments. Use this function with caution, as high

SWR will damage Q10, the PA transistor. I strongly recommend using a series of

DOTS to set/check any tuner adjustments.

ATT button

Pressing the ATT key invokes the receiver attenuator (ATT) on or off. This provides an
overly generous amount of loss (~20dB) and is of minimal use to the operator. The
ATT serves to replace an RF gain control.

I'm sorting out how to reduce this, but it will require changing out one (or more) SMD
resistors.

tap

the CALL button. The letter E will confirm your exit.

Test Carrier

Attenuator:

CALL until you hear the letter T (which follows S and I in order).

DASH

DOT

paddle to turn it off. To escape from

function allows you to lock the key down when using paddles to take

paddle to initiate a

Transmit Carrier

10

1.0 How to Use this Guide:

As you examine the Table of Contents, you will see the radio set broken down into
several basic sub-systems. Each of these sub-systems must work properly for the
whole to perform. The order of the sub-systems is specific by design. Each section
builds on the one before.

Please, READ the radio overview and the
you attempt

any

of the troubleshooting steps. A basic understanding of each of the

entire

Concept of Operations sections before

sub-systems is essential to be able to perform the troubleshooting steps that follow.
Most sub-system sections will have either a portion of the schematic or block diagram
as part of the description.

Test points used in troubleshooting are identified in a linked illustration. A photo really
is worth a thousand words, or nearly so... These photos are linked in the text for
testing/repair to save space and reduce confusion. The images included may be

zoomed

(CTRL and +) to 400% or more and still be readable. To return to the test

step, use the Back button on your reader.

The troubleshooting steps are not in with the sub-system description, again, to avoid
any possible confusion. Each of the troubleshooting steps builds on the prior step. In
other words, you must ensure the DC power system is operating properly before you
can tackle an issue, say, with the transmitter.

The information in this guide was obtained by direct observation and measurements on
a working 9200 with a Series B board. Older radios, those with an A series board,
may or may not work with the manual directions as I did not have access to a
unit to confirm.

This guide is based on the 9200-B board version. The software displays 08-2011 on
power up with both the VFO/Mem and Mode/RIT buttons held down.. This manual will
lay out troubleshooting steps, explain how to perform specific repair actions and
suggest others.

Finally, if you cannot resolve a problem with your radio, you can open an on-line
trouble ticket with MFJ Enterprises and request a quote for repair. Ensure you
document what steps you have taken and the results – then put that information in the
trouble ticket.

Good luck!

73s // Don // KL7KN

Return to TOC

11

2.0 Warnings page

This radio contains Electro-Static Sensitive Devices (ESD). Use an appropriate
conductive/grounded work surface when preforming repairs.

If you will be soldering anything on this radio, use of an ESD –safe rated soldering iron
with proper grounding is a must.

Use a personal ESD grounding device for yourself before beginning work on the radio.

Perform soldering only in a well-ventilated area!

ALWAYS wear eye protection when soldering! The eyes you save will be your

own.

DO NOT key the radio without connection to an antenna, dummy load or into a high

SWR load

– you will damage the transmitter

. If using an external tuner, avoid

extended key down times when making adjustments.

While the DC input is diode protected, use a fuse – 2 amp – inline on the DC input
cable.

If using the internal DC header (J2) to power the radio via internal batteries, use a
polarized plug. Insulate any battery used internally to avoid shorting vital components.
Secure any internal batteries to prevent movement which could damage the radio.

Do Not attempt to use the external DC supply to charge user installed internal battery
packs. Damage to the unit may result.

When installing band modules, check to ensure the header pins line up correctly and
are fully seated

before

installing rear cover and applying power to the unit. (See Band
module section for more.) After transport, check Band Module is fully seated before
use.

Before any power on tests are made, ensure you have a set of phones and a dummy
load attached to the radio or main board before applying power.

I STRONGLY suggest that operators remove the DC supply and antenna connections
when the radio is not in active use.

Remove any user installed internal batteries prior to the radio being stored.

Return to ToC

12

Recommended tools & test equipment:

You will need some

minimum test equipment

to perform any troubleshooting on the

MFJ-9200 radio set. These are:

Multimeter. Sometimes called a V-O-M for a Volt, Ohm, Milliammeter. You may also
see these called a DMM, for Digital MultiMeter. This unit will be used to measure
voltage at several points within the radio set. I've made measurements listed with both
a VOM and DDM. Any differences because of the meter type are identified.

The meter used must be a

quality

unit, with a listed input impedance of

at least

20K
ohms/volt, with 1M ohm/volt preferred. A quality DDM may be found new at a cost of
under $50 USD and can be used for other tasks, such as checking fuses or confirming
power is present at a connector.

 Test leads for your meter should have a sharp point to allow measurement at a

specific pin on a small SMD device without shorting across to any other pin.

 The test leads should have a way to clip at least one lead to the chassis ground.
 The test leads should be color coded, usually red and black, to indicate polarity.

Resistive Dummy Load. Used to terminate the transmitter chain, this will both
prevent damage from transmitting into an unterminated connecter and allow a way to
determine output power. If you don't have one, look at the end of the maintenance
section. I'll show you how to build a dummy load for a few dollars.

Wattmeter

and

Dummy load. A nice kit is available from Pacific Antennas and Kits

for under $20. This allows use of you DMM to read power out. (See www.qrpkits.com).
At some point, as an active Amateur operator, you will need to have some kind of
working watt meter.

Signal tracer or Oscilloscope. I've been building or repairing radios since 1970 and
I still don't have one at home for shack use. What to do? I use a small (portable)
general coverage receiver, specifically an ATS-909. Most tests with the radio are just to
see if a signal is present or not. In newer digital radios, generally something either
works or it doesn't. If I can hear something on the radio, I can keep going.

Signal Generator. While nice to have, there are alternatives for a new ham:
A low-cost antenna analyzer, such as the MFJ 207, can serve as a signal source.
There are multiple "DDS kits" to be found on line that may be used as a basic signal
generator. One such kit is the N3ZI kit – http://www.pongrance.com/super-dds.html ­about $80 USD. The QRPGuys (www.qrpguys.com) have some nice test gar as well.
If you have another HF rig, feed it into a dummy load at low power, and then use it as
a signal source.
Used commercial equipment may be found from time to time, but maintenance,
manuals and ongoing calibration can be problematic for the amateur radio operator.
Finally, a wire antenna can provide a small, broadband signal for use in very basic
troubleshooting.

Return to ToC

13

Hand tools:

Screwdrivers (small and very small). Since the -9200 is tiny, your screwdrivers are
going to be typically called a "Jeweler's screwdriver set" or the like. The only two
internal adjustments available are very small. You will need to pick up a non-metallic
set as well to tune the RF cans on a couple of the Band Modules.

Small needle nosed pliers. The kind with a wire cutter are nice to have.

Adjustable wrench (spanner). It is used to remove the BNC connector from the chassis,
remove the PA transistor screw mount and internal standoffs.

Non-metallic tuning tools, both 1/8 Hex head and small screwdriver type.

An ESD- safe soldering iron and ESD-safe work surface.

-An ESD-safe soldering iron will be marked as such and on low-cost units is
distinguished by a 3 prong AC connector. If you plan on attempting your own
repairs as a matter of course, investing in a better grade unit, often called a
soldering "station", is a worthwhile investment.

-I use a roll-up ESD safe pad to work on. This pad has a snap connection for my
wrist-strap so I and the work surface stay at the same potential. You may be
tempted to skip this expense, please don't. Cost is only about $30 USD for a nice
unit.

Solder pump and soldering wick. You will need these to be able to remove any installed
active devices. I have a spring powered solder pump that is nice for fast work.
Wicking works as well, it's just not as fast.

Solder pump – an under $4 USD example is from New Egg. They call it a "Solder
Sucker Desoldering Pump Vacuum Soldering Iron 19cm Repairing Tool". Wow.

Solder wicking may be found on-line at Mouser Electronics or DigiKey. Get the
Static Dissipative (SD) rated wicking. It's sold by the roll. Get a couple...

Magnifying lenses – you

will

need them. A headband unit with dual lenses allows
working hands-free. Pick whatever will work for you, but you will need to be able to
clearly see the pins on an installed SMD IC to check the supply voltage, if nothing else.

Safety glasses for soldering! No joke, get 'em, wear 'em!

Save your eyesight...

For testing, a 50 ohm dummy load may be made with a pair of 100 ohm, 2 watt
composite resistors in parallel and a BNC panel mount. BNC male to male adapter
allows use on this radio.

14

Return to ToC

Basic radio overview

The MFJ-9200 is a miniature, single-conversion transceiver that operates on six
of the Internationally allocated high frequency bands within the Amateur Radio Service.
The unit is all digital. The VFO control provides for tuning in 100kHz, 1KHz and .1KHz
increments. The RIT function permits receiver tuning in 10 Hz increments.

In addition to manual tuning via the rotary encoder, eight memories
are provided to store frequency/mode. Changing between stored Memory and the VFO
is by a pushbutton. Changing between bands is done by swapping out a compact Band
Module.

Placement of the operator controls clearly puts this radio in the class generally
known as
in bright sunlight and it has a backlight for viewing at night. The backlight may be
turned off for a

adjacent signal interference. The filter may be set for narrow (CW) and wide
(USB/LSB). This bandwidth change is controlled by a simple pushbutton. Receiver
performance is impressive, with Minimum Discernable Signal (MDS) levels of 0.1 to 0.2
microvolts (-127 dBm @ 50 ohms) typical.

directly by the DDS system. The transmitted signal passes through several filters to
reduce harmonic content in the output. The transmitter final amplifier, a robust
2SC2078 transistor, is protected from high VSWR by a Zener diode. The antenna is
attached via a BNC connector mounted on top of the unit.

Use of a straight key is supported as well. (See operation manual for more). A keyer
memory allows automated calling of CQ at the push of a button. It is not possible to
reverse the Dot/Dash sense, you must rewire the plug to swap paddle sides.

nominal power of five watts output with 12 DCV applied. The power input and an
internal DC feed (J2) are both protected against reverse polarity. External power
supplies must be able to provide up to 2 amperes of current with no AC ripple. A
simple battery pack made up of eight "AA" batteries provides ample power.

Trail Friendly

significant

The receiver is single conversion, with a crystal ladder filter to reduce noise and

The transmitter is a classic Master Oscillator/Power Amplifier (MOPA) type fed

The internal keyer supports iambic keying via a set of operator-supplied paddles.

Operating on a DC input between 8 and 15 Volts DC, the radio transmits with a

. The high-contrast digital display is large enough to easily read

saving in current draw on receive.

per band

More detail is provided in the sub-system descriptions that follow. Return to ToC

15

3.2 DC power busses and protection:

The MFJ-9200 uses several voltages to operate. One power buss is unregulated.
The applied DC voltage, either from the external or internal source, will be measured on
this buss. This buss feeds the PA section. So higher voltage means more power out
and lower voltage lowers the power out. 5 watt output is easily obtained at 12.8VDC.

DO NOT exceed the 14.8 VDC limit on DC input power.

3.3 DC Voltage regulation:

The two additional power busses present are regulated. One buss is regulated for
+5 Volts DC and the other is regulated for +6 Volts DC.

Regulation for the DC busses is provided by a solid state regulator device, a 78Lxx
SMD. These three lead devices are robust and provide excellent regulation as power
varies in situations with marginal batteries, such as on extended transmit.

A potentiometer, labeled as "VR" is used to make an adjustment and is found on the
main board. This sets the displayed voltage on the main display. (See Illustration)

3.4 DDS VFO sub-system

The Direct Digital Synthesis (DDS) sub-system the MFJ-9200 is based the
popular Analog Devices AD9834 chip. The AD9834 is a 75 MHz low power, DDS device
capable of producing high performance sine wave outputs, using the installed 60MHz
oscillator as its clock source. The DDS output is determined by the MCU per the
encoder settings. With the clock source provided, the DDS chip has an output
resolution

oscillator. The HOSONIC made unit installed has a claimed 50ppm stability. "Better"
units are available (20ppm, for example) but the one used seems to be well within
amateur limits. If you were to zero-beat the radio with WWV, for example, you would
be hard pressed to even hear a 100 to 300 cycle note if off-frequency. Use of an
oscilloscope and a highly accurate signal generator would be required to determine
what, if any, difference in the VFO setting and the actual output frequency exists.

The output of the system is buffered to eliminate loading of the DDS system.

value. On receive; the DDS output frequency is plus or minus 4.9152 MHz (band
dependent) from the displayed VFO value. This off-set matches the first conversion
scheme to allow the crystal filter to function.

(MCU). I don't have a way to read the embedded MCU code, and if I did, I still
wouldn't put the code in this manual. Since the code is mature (8/2011) this normally
wouldn't be required in ordinary circumstances. I am unaware of any method to
purchase a replacement MCU from the manufacturer.

under 1 Hz.

The accuracy and stability of the entire radio is dependent on this clock

Output of the DDS system ranges from a low of 3.5 MHz to a high of 21.45 MHz.

On transmit; the DDS system output frequency is identical to the displayed VFO

The AD9834 is controlled via a 3 line serial interface from the PIC controller

16

Band & test freq

Transmit setting

Receive setting

DDS output

80 meters 4.0 MHz

4.000 MHz

4.000 MHz

4.000 MHz

8.9152 MHz

40 Meters 7.100 MHz

7.100 MHz

7.100 MHz

7.100 MHz

12.0152

30 Meters 10.100 MHz

10.100

10.100 MHz

10.100

5.0848 MHz

20 Meters 14.100 MHz

14.100

14.100 MHz

14.100

9.1848 MHz

17 Meters 18.100 MHz

18.100

18.100 MHz

18.100

13.1848 MHz

15 Meters 21.100 MHz

21.000

21.100 MHz

21.000

16.1848 MHz

Frequency chart for DDS system for selected frequencies

NOTE – BFO oscillator is crystal-controlled to 4.9152 MHz.

NOTE – Center frequency of crystal filter is nominally 4.9152 MHz.

Return to ToC

17

3.5 Band Module diagram and header pin-outs

(See Illustrations – Band Module)

I cover the band module in order for an operator to understand how it fits into
the overall system. You
There are no user-serviceable parts as the capacitors are, as far as I can see,
unmarked. If a module faults, a replacement is available from MFJ Enterprises or their
dealers for under$30 USD. BTW, the Band Modules are manufactured right here in
the USA by MFJ.

I arbitrarily numbered the header pins on the band module 1 to 8, left to right
for convenience. The schematic provided doesn't number these pins, so these numbers
are as good as anything else. Just remember, the sockets on the main board will be
numbered in the opposite sense. (1 to 8 right to left – see Illustrations.)

The Band Modules all have the same MFJ part number and the board layout is
identical. Only the installed components – L1, L2 and related capacitors and resistors
are different. All silk-screened markings are identical as well.

As I examined the modules, I was looking for something that might be used to
cue the MCU as to what module is installed, thus to bring up the DDS/VFO with the
correct band settings. I had initially thought that three of the pins in the eight pin
header might be grounded or not to present a digital number from zero to seven.

As it turns out, I was overthinking the issue. Pin 1 of the band module runs to
ground through a resistor labeled R1. Each band module has a different value of R1.
Tracing this pin back out into the board, it runs through what I take to be a resistive
voltage divider network which then leads to the MCU. Pretty slick.

must

have a Band Module installed for the radio to work.

This is diagramed on the next page.

THIS SPACE INTENTIONALLY LEFT BLANK

18

Pin 1

Pin 3

Pin 7 & 8

8 pin header

Pin 1 R1 Ground.

Pin 2 Ground.

Pin 3 C1, C2, L1, L2 C6, C7, Pin 7 & 8. To antenna

Pin 4, 5, 6 Ground.

Note – Pin 7 & 8 are tied together and feed to the BNC connector center conductor
solder pad labeled ANT.

The RF power from Q10 enters the Band Module via L8 and C2 to Pin 3 of the header.
After passing through the filter of C3, C4, C5, C6, C7, L1 and L2, it leaves the header at
Pins 7 and 8 going to the ANT pad, the BNC connector and on to the antenna.

THIS SPACE INTENTIONALLY LEFT BLANK

Return to ToC

19

Band

R1 Label

R1 Value

80

101

100

40

222

2.2K

30

472

4.7K

20

103

10K

17

223

22K

15

473

47K

6 pin header

Pin 1 Q2 switching transistor, then to first mixer. Feeds in to T1 on BM
NOTE – The socket for this pin on the main board will be used as a Test Point later.

Pin 2 Ground.

Pin 3 C3 then also feeds into T1.

Pin 4 Ground.

Pin 5 T2.

Pin 6 T2 (to board D1 & D2).

The receive signal enters the band module at pin 3 of the 8 pin header. The
signal travels through C8 before connecting to the socket for pin 6 of the 6 pin header.
Pin 6 is on the trace that leads into T2. Pin 6 also feeds out to D1 and D2 on the main
board, which is part of the T/R muting circuit. This allows QSK operation.

After going through T2, the signal is present at pin 5. Pin 5 feeds out to the
main board attenuator circuit. (See Illustrations – Attenuator R1 @ 221)

The RX signal leaves the Band Module going through C3, C11 before going out
pin 1 to Q2, a switching transistor. From there, it goes to the first of two SA612 mixers.

Between C3 and C11, a trace leads to T1 making it part of the circuit. I assume
the circuit is grounded inside the can where the connection isn't visible. Pins 2 and 4
are grounded.

T1 and T2 are adjusted for best (loudest) receive signal at a frequency you
choose.

NOTE – How to read SMD resistor values. The first two numbers denote significant digits. The third

digit is the multiplier, that is, the- power of ten which the two digits are multiplied. Basically, the third
digit is how many zeros to add. Resistances of less than 10 ohms don't have a multiplier. Instead, the
letter 'R' is used to indicate the position of the decimal point.

3-digit code example:
220 = 22 × 100 (1) = 22 ohm – not 220 ohms
471 = 47 × 101 (10) = 470 ohms
102 = 10 × 102 (100) = 1000Ω or 1k ohm

Return to ToC

20

3.6 Receiver

 Signal path.

The desired signal leaves the antenna and enters the radio via the BNC connector.

The signal then enters the installed Band Module.

The Band Module acts as a bandpass filter, utilizing several capacitors & both T1
and T2. RF energy outside of the passband defined by T1 and T2 is severely
attenuated. This is why there is the need to peak the two coils on the Band Module
and is so important for receiver performance.

Leaving the Band Module, the signal enters the first of two SA602A mixers. There,
the incoming RF is mixed with the signal from the DDS sub-system. The output of the
SA612 now contains the two original signals (RF and DDS)
of the two signals. This is the

Intermediate Frequency

plus

the sum and difference

or IF. This complex output
feeds through a buffer amplified Q2 into the ladder filter, a matched set of four crystals.
The crystals in the filter are marked as 4.9152 MHz.

The ladder filter, acting as a high-Q, series resonant circuit, then feeds the signal
into the second SA612 mixer. This filtered signal (IF) is mixed with the output from the
BFO sub-system. The BFO oscillator is crystal controlled at ~4.9152 MHz. Again, the
output of the second mixer has both original signals

plus

the sum and difference of the
mixer input. One of those output products is the recovered audio (AF) or CW note from
the signal that entered at the beginning. This goes to the LM386 audio amplifier,
through the Volume Control potentiometer and on to the Phone output jack.

This double mixer scheme, with crystal filter, is seen in many other MFJ QRP radios
and is vastly superior to the simple Direct Conversion (DC) receivers of an earlier age.
This circuit architecture allows filtering of unwanted noise and out of band signals, such
as shortwave broadcasters. It is also inherently a low-noise system.

Return to ToC

21

Discussion on receiver and filtering scheme:

The DDS system, in receive, feeds the first mixer a signal that is offset from
the desired (displayed) frequency by the value of the ladder filter crystals +/- 4.9152
MHz. The DDS signal and the received signal are mixed in the SA612.

Since the crystals in the ladder filter act as a narrow passband filter, only the
desired signal (4.915 MHz and the intelligence it carries) is found at the output.

The crystals act as a series resonant circuit and are much smaller the equivalent
capacitor, coil and resistor of such a complex circuit. The Q or bandwidth of the ladder
filter is changed by use of a set of 'shunt' or swamping capacitors.

You see shunt caps to the right of the crystals on the main board with several
switching transistors (Q3, Q4, Q5). The bandwidth is changed by these capacitors as
the transistors are switched by the MCU when selecting CW or USB/LSB.

Why does this matter? In the test equipment section, I stated I use a portable
general coverage radio, an ATS 909 to be exact, as a signal tracer. With the BFO active
in my portable, the DDS, BFO and mixer products can be heard as a tone on the radio.
Since the portable radio is fairly accurate, I can quickly see if the DDS system is
working and on frequency, the filter has an output and the BFO system is working and
on frequency by setting the radio to listen for the expected signal.

The DDS sub-system has a Chart of frequencies for the DDS chip in both
transmit and receive states. This data is also used in the troubleshooting section.

For the receiver to work correctly, the BFO must be set properly to maximize the
receiver performance. If the BFO is off-frequency, the product of the second mixer
may be not be heard. The BFO is adjustable because the DDS source may be slightly
off from the displayed value.

Attempt adjustment the BFO only if troubleshooting steps call for an
adjustment. Follow detailed adjustment steps
an effort to repair a problem will just lead to...more problems.

exactly

. Randomly tweaking things in

Leave it alone!

See adjust VC for more on this aspect of the BFO.

22

Return to ToC

Keying wave form
at Anode of D4

Keying wave form
at Cathode of D4

3.6.3 Audio switching, muting and side-tone:

Unlike many of the contemporary QRP radios on the market, the -9200 does
not use relays for band-switching, muting or side-tone. It is also one of the few
that offers a real AGC function. Automatic Gain Control or AGC is what keeps your ears
from being blasted by strong stations as you tune across the band.

For the operator this is an important distinction. Electromechanical devices, such as
relays, are a prime failure point on many radios. Let's look at how the 9200 performs
essential T/R muting, provides side-tone and AGC while avoiding the need for relays.

When the radio is keyed, the keyer chip, IC7, Pin 6 changes state. Since Pin 7 is
connected to the anode of D4, the state change is also seen at the Emitter of Q6, a
unijunction transistor. Q6 acts as a switch, cutting off the audio feed to IC2, the LM386
audio amplifier. While switched, the RC combination of C47/R33 charge up to the same
potential as the cathode of D4. What does this look like?

These images provided by and used with permission of Robbie, G0GUH.

When the key goes up, IC7, Pin 6 changes state again, and the voltage drops. The RC
time constant of C47/R33 allows a gentle drop (sloped line) and thus, the audio does
not pop upon T/R switching.

Wicked cool stuff

.

Return to ToC

23

At the same time, when IC7 (the keyer) is active, Pin 7 feeds a tone to the audio path
leading to the headphone jack. This means side-tone is not adjustable for either pitch
or volume. The LM-386 has no output and so you hear the side-tone.

If you will now look at IC3 (the LM386) – Pin 5. This Pin is connected to the Cathode of
D3 via a couple of resistors and a capacitor. The Anode of D3 is connected, in turn, to
the base of Q1. Note that Q1 is a 2N3904, an amplifier, not a switching transistor like
Q6.

The collector of Q1 is tied to IC1 (the SA612) , Pin 2 – this is the first mixer. This chain
forms an

AGC loop

.

As the audio comes from the LM386, it is rectified by D3 and fed to Q1. This in turn
changes the input to the first mixer, providing a fairly robust AGC action for the
receiver. As the audio voltage varies, the input to IC1, Pin 2 changes at the same rate.

R20 and C21 provide an RC time constant to keep the AGC from 'pumping' the input on
all but the strongest stations. This loop benefits from the crystal filter just ahead of the
second mixer. The filter reduces any effect of strong stations just a few KHz away from
the desired station also causing the AGC to 'pump' the input to the first mixer.

Thus, with a few components, and a bit of clever engineering, receiver system AGC,
T/R switching and audio muting is provided without the need to resort to relays. This
allows QSK (fast T/R switching) and a pop-free audio feed with at least some AGC for
strong stations.

I have to say, there is a lot to love about this rig….

THIS SPACE INTENTIONALLY LEFT BLANK

Return to TOC

24

3.7 Transmitter

Signal path and SWR protection for final amplifier.

As mentioned earlier, the transmitter is a simple MOPA type. The signal from the
DDS sub-system is fed to Q7, Q8, then Q9, before going into the input side of T1 (8
turns). The output side of T1, the smaller link coil, feeds Q10 the 2SC2078. The signal
is amplified by transistor Q10, passed through the Band Module for filtering before
going to the BNC connector.

T1 is the large toroidal transformer next to Q10 and is used to link the transistor
base to the incoming DDS RF. L8 is a fixed inductor and is mounted on the face of the
main circuit board. Note that Q10 is supplied by the unregulated supply. As the supply
voltage drops, so will the power output.

I would note that the HB-1B MK 3 now uses this same setup.

All capacitors and inductors in the transmitter are fixed. There are no
adjustments possible by the operator nor are any needed. If you don't have a resonant
antenna, then some kind of matching unit is

required

. A mismatched antenna produces

high Voltage, Standing Wave Ratio (VSWR).

These 'mismatch voltages' can cause failure of the final by exceeding the
Base/Collector or Emitter/Collector breakdown voltage rating. In an effort to protect
the final transistor, a Zener diode, rated at 43 Volts, is installed. Once the voltage
present at the emitter exceeds the 43 volt level, the Zener diode will start to conduct,

hopefully

saving Q10. I've called out a 36 volt Zener as a replacement. It might save

you from replacing Q10 again...

Any time you are testing, always have a 50 ohm dummy load connected to the BNC
connector or between the ANT pad and ground.

The TO-220 case for Q10 has a standard pin-out. The 2SC2078 is a common device.

Return to ToC

25

4. Troubleshooting Basic Radio Problems:

4.1. Radio does not function (seems to be dead)

Reminder – Click link to view relevant illustration.

Confirm by: Attach power, headphones and dummy load. Confirm – no sound in
headphones, display remains blank, backlight on display does not function.

Test Steps/Results/Action:

If in-line fuse on DC supply cable blows repeatedly, STOP. An internal short will cause
the in-line fuse will blow repeatedly.

If the SWR protection diode, C-55, or Q10 are shorted, the DC supply is grounded.

Quick Check 1

supply/battery. That is to say, connect the meter to the power leads, then the power
lead to radio.
When the power switch is activated, the ohm meter should read

NOTE - If the reading is above 36K then

 If meter indicates an open (zero on a VOM or 1. on most DMM),

ohm meter leads as the reverse polarity protection diode is blocking your
reading .

 ~36K ohms is indicated, go to 1).
 Short (zero) indicated, go to Quick Check 2.

Quick Check 2

1) Check DC supply:

Remove DC feed connector and measure voltage and polarity present at connector:

-DC supply may be below 8 volts.

-DC supply may be not be present (cable/connector broken).

-DC supply at connector may have wrong polarity (must be + center/- on

exterior).

Action: Correct issue with DC supply, if found.

: Disconnect power cable; attach an ohm meter in place of the power

around

drops

, it is an indication that C-55 is charging.

- Check SWR protection diode first. Then check Q10 then C-55 for short.

36K ohms.

reverse

the

If DC feed voltage is correct - Remove rear cover.

2) Find J1. Check for supply voltage at rear of jack. Supply voltage present?

Yes? Continue.

No? Fault. See Action item 1.

NOTE – The operator supplied connector and installed jack may not fully match due to
manufacturer tolerance mismatch. Wiggle the connector to see if voltage appears. If
supply voltage does appear, replace supply connector.

3) Find power switch Check for supply voltage at center pins. Voltage present?

Yes? Continue.

No? Fault. See Action item 2.

Return to ToC

26

4) Find TEST POINT +5VDC. Check +5 VDC . Is 5 VDC +/- 5% found?

Yes? Continue.

No? Fault See Action item 3.

5) Find TEST POINT +6VDC. Check +6 VDC . Is 6VDC found?

Yes? End of test. All DC supplies test as operational.

No? Fault. See Action item 4.

Action items:

(1) Supply voltage not present at J1. Possible fix, replace J1.

(2) Supply voltage not present. Possible fix, test/replace diode D5.

(3) +5VDC not present at Test Point. Possible fix, replace 78L05.

(4) +6VDC not present at Test Point. Possible fix, replace 78L06.

Final Action: If the above steps fail to correct problem, open a trouble ticket with MFJ,
request quote for repair. Document steps taken and result for inclusion in trouble
ticket.

4.2. No received signal is heard:

Confirm by: Attach known good: Power, headphones and dummy load or known good
antenna. Attach adjustable signal source to dummy load. There may be no sound in
headphones. Volume control moves easily. Display operates normally indicating a
Band Module is installed, backlight on display functions.

Test Steps/Results/Action:

1) Remove back cover. Ensure Band Module is installed correctly. If so, trade out Band
Module. This is an unlikely fix, but a simple first check.

Action: If different Band Module restores operation, inspect/replace suspect Band
Module.

2) If changing the Band Module makes no difference, remove installed Band Module.

-Find the 6 pin header on the main board. Take an unconnected test lead and

touch header socket marked as PIN 1. Is noise heard?

Yes? Continue.

No? Additional testing required. See Action item 2.

3) Find LM386 (IC3). Carefully touch the test lead to PIN 2. (The circuit board trace
from this pin leads to top of Q8). Is noise like a 60 Hz hum heard?

Yes? Continue.

No? Additional testing required. See Action item 3.

4) Find pins feeding the Phones Jack.

On Ohmmeter, select lowest value for Ohms, measure between the Tip and

Sleeve/Ring and Sleeve. Is a popping noise heard in headphones?

No? See Action item 4.

Yes? All receiver subsystems appear functional. See Action item 5. See Action

item 6.

27

Action items:
(2) Path from first mixer to audio output appears functional.

See Test DDS.

(3) Path to audio output appears functional.

See Test First mixer. See Test Second mixer. See Test BFO.

(4) Phone Jack may be inoperative. Possible fix –Replace the Phone jack.

(5) The SWR protection diode may be shorted. See Test SWR protection diode.

(6) The Band Module may be defective. See Bypass Band Module.

Action: If these steps fail to correct problem, open a trouble ticket with MFJ, request
quote for repair.

If Phones jack was replaced, restart checks at top of this tree.

4.3. No RF output

Confirm by: Attach known good: Power, headphones and dummy load. There may be
sound in headphones. Display operates normally indicating a Band Module is installed,
backlight on display functions. Signals are heard with antenna attached.

Set VFO to listed test frequency (example – 10.100MHz). When keyed into the dummy
load, no apparent signal is transmitted or watt meter indicates no output or very low
output. Sidetone maybe audible in headphones when keyed with either a straight key
or a set of paddles.

Alternatively, set tracer/radio to test frequency as above. A very loud tone should be
heard when -9200 is keyed. A very weak or no tone indicates a possible fault.

Test Steps/Results/Action:

1) Confirm DC power is correct at supply. Measure between 8VDC and 15VDC.
Is supply voltage between 8 and 15VDC ?

Yes? – Continue.

No? – Fault. Correct supply voltage before any more testing.

2) Confirm DC supply voltage is present at each pin of L8. (Two pins between C2 and
C3 on main circuit board). Is supply voltage is present on both pins?

Yes? – Continue.

No? – Fault. L8 appears to be open. Replace L8.

3) Test DDS to confirm output frequency is correct. Is DDS on correct frequency?

Yes? – Continue.

No? – Fault. Contact MFJ Enterprises for a repair quote.

4) Remove dummy load, headphones and power. Remove back cover. Ensure Band
Module is installed correctly. If so, trade out Band Module. This is an unlikely fix, but a
simple check.

28

If different Band Module restores operation, inspect/replace suspect Band Module. It is
possible, though unlikely, that the receiver will work, but there is some fault in the
transmit filter section. Examine L1 and L2 closely for a broken lead.

5) If changing the Band Module makes no difference. Test SWR protection diode to see
if it is defective. If receiver is working, this is very unlikely, but it is possible that the
diode conducts when unit transmits.

Alternatively

, if using dummy load, remove SWR protection diode. If it is faulted,

transmit power should be seen on wattmeter.
Note - This diode normally has supply voltage present at anode at all times radio is on.

6) Check that Q10 has power.

-Remove main circuit board from chassis.

-Attach power, headphones and using a pair of test leads, connect 51 ohm

resistor between the ANT pad and ground.

-Using voltmeter, confirm supply voltage is present on Pin 2 (center pin) of Q10

as seen from front of main circuit board. Is supply voltage present?

Yes? – Continue.

No? – Additional testing required. See Test Q10.

7) Check that C55 (470 uF electrolytic capacitor) is not shorted. This is only possible
from front of main circuit board. If shorted, replace.

After all checks are performed and results are normal, additional troubleshooting will
require advanced test equipment. Contact MFJ Enterprises for a repair quote.

4.4. No or low audio output

Confirm by: Attach known good: Power, headphones and dummy load. There may be
some sound in headphones. Display operates normally indicating a Band Module is
installed, backlight on display functions. Signals

may

be heard with antenna attached.

Test Steps/Results/Action:

1) No audio. Check audio path using steps from Chapter 4.2

2) If some audio is heard, but at a low volume, no matter where the volume control is
set. Use one test lead to bypass the volume control.

-Find the three pins nearest R21. These are found below and to the left of the
crystal filter. A trace goes from R21 to the leftmost pin. The center pin leads to J4
(Phones) on the front of the main board.

-Short between these two leads, this will bypass the potentiometer.

-Volume should be 'loud'. Did audio output increase?
Yes? – Fault. Replace potentiometer.
No? – Contact MFJ Enterprises for a repair quote of the LM-386.

Return to ToC

29

4.5. Radio doesn't key or keys erratically

Confirm by: Attach known good: Power, headphones and dummy load. There may be
sound in headphones. Display operates normally indicating a Band Module is installed,
backlight on display functions. Insert key plug, press key or paddle. Radio doesn't
transmit or transmits erratically.

Test Steps/Results/Action:

1) No transmit. Using VOM, confirm that a short develops on Tip to Sleeve on key plug
when key is pressed. If using paddles, check both Tip and Ring to Sleeve for a short
when paddle contact closes.

-Did VOM indicate a short when key/paddle contact closed?
Yes – Continue testing.
No – Fault. Assuming key or paddle contacts are clean, check, then replace or
repair cable.

2) Erratic transmit (drops out with key pressed)
Remove DC power, headphones. Remove back cover. Find J3, key jack. Locate R36
and R37. The trace leads back to IC 7, pins 2 and 3. See Illustration.
IC-7 is the keyer chip. Connect dummy load, headphones and power. Grounding
either pin 2 or pin 3 at J3 should cause the radio to transmit. Using test lead, short
between Tip or Ring and ground at J3. Radio should transmit.

-Did radio transmit when pin 2 or 3 is grounded at key jack?

Yes – Fault. J3 may be loose or have bad contacts internally. Replace J3.
No – Fault. Contact MFJ for repair quote.

4.6. Display is dead, displays "funny characters" or has no backlight

Confirm when radio is powered up that boot screen displays, then current frequency
displays. If display does not show correct information (numbers), it may have faulted.
Or - Backlight doesn't light when B/L button pushed.

1) Check DC supply. If OK, continue.

2) Check voltages on display.

-Pin 2 to ground should have +5 VDC.

-Confirm ground is present.
Is +5VDC found on correct pin?
No? If +5VDC test good and no voltage found on pins 2. Fault. See Action item

1.
Yes? If +5VDC test good and voltage is found on pins 2. Fault. See Action item

1.

Continue to next page

30

3) Backlight button feeds +5VDc to Pin 15 of display. Check voltages on display.

- When B/L button is depressed, button should remain depressed.
Does button stay 'down' when pressed?
Yes? – Continue.
No? – Fault. See Action item 2.

-When B/L button is depressed, button remains depressed and + 5VDC is seen
on pin 15.
Does +5VDC appear on pin 15?
Yes? – Fault. See Action time 1.
No? – Fault with button. See Action item 2.

Action:

1) Replace display. CAUTION – several pins on the display lead

directly

to MCU. Use

of ESD safe soldering iron required.

Alternatively - Contact MFJ Enterprises for a repair quote.

2) Replace pushbutton. P/N and mfg are unknown. Contact MFJ Enterprises for a
replacement part quote.

4.7. Radio is off frequency (display doesn't match measured output

signal)

Confirm by: Attach known good: Power, headphones and dummy load. There may be
sound in headphones. Display operates normally indicating a Band Module is installed,
backlight on display functions. Signals may be heard with antenna attached.

Set VFO to listed test frequency (example – 10.100MHz). When keyed into the dummy
load, no apparent signal is transmitted, tracer/radio hears no signal. Tuning
tracer/radio to a different frequency may yield a tone, indicating Transmitter is off
frequency. Sidetone audible in headphones when keyed with either a straight key or a
set of paddles.

Alternatively, set tracer/radio to test frequency as above. A very loud tone should be
heard when -9200 is keyed. A very weak or no tone indicates a possible fault.

Check receive by setting signal source to listed test frequency using tracer/radio as
confirmation. Ensure RIT is not active. A loud tone should be heard.

1) Check DDS subsystem. If DDS shows as good in testing for receive, but off
frequency for transmit, the MCU is faulted. The same is true for the opposite symptom,
good frequency on transmit, off frequency on receive.

Does receiver or transmitter appear to be off frequency?
Receiver – Check that the RIT is not active. RIT not active? See Action item 1.
Transmitter – Transmitter off frequency? Yes – See Action item 1.

Action:

1) Contact MFJ Enterprises for a quote for repair.

31

Return to ToC

Band & test freq

VFO displays:

DDS output

80 meters 4.0 MHz

4.000 MHz

8.9152 MHz

40 Meters 7.100 MHz

7.100 MHz

12.0152MHz

30 Meters 10.100 MHz

10.100 MHz

5.0848 MHz

20 Meters 14.100 MHz

14.100 MHz

9.1848 MHz

17 Meters 18.100 MHz

18.100 MHz

13.1848 MHz

15 Meters 21.100 MHz

21.000 Mhz

16.1848 MHz

Testing specific radio sub-systems:

Test DDS

Test Steps/Results/Action:

1) Remove back cover. Attach power, headphones and dummy load. Using this Chart,
set VFO as shown for Band Module installed. Set signal tracer/radio to DDS output
listed in chart below.

- Place the tracer/radio input lead over the DDS chip. Is a tone heard at listed
setting?

No. See Action item 1.
Yes? End of test, DDS system appears to be functional.

-If possible, set tracer/radio to 60 MHz. Is a tone heard?

No. See Action item 1.
Yes? End of test, DDS system Master Clock source appears to be
functional.

(1) This test indicates the DDS system is inoperative.
Action: Open a trouble ticket with MFJ, request quote for repair. Repair of the DDS
system/Master Clock Oscillator requires additional (and expensive) tools and
techniques, putting any repair beyond the scope of this manual.

Adjust +5 Volt supply:

 VR adjustment for +5 VDC buss: (board may be in chassis or out)

Step 1) Ground negative lead (com or black) of meter to board by clipping to ground

point.

Step 2) Attach dummy load, phones and DC supply. With back cover removed and the
unit face down, locate TEST POINT for +5VDC.

Step 3) Using positive (+ or red) lead from your meter, measure voltage at TEST POINT
+5VDC. If voltage is +5 VDC +/- 5% (this is 0.25 volts or 4.75 to 5.25) no adjustment
is required. If the voltage is off by more than 5%, adjust VR until +5 VDC is obtained.

Step 4) Remove power and reassemble radio.

NOTE – adjustment of control VR required a small Phillips head screwdriver.
NOTE – the +6VDC buss is not adjustable.

32

Return to ToC

Test First mixer

Test Steps/Results/Action:

NOTE – with a Band Module installed, access to the first mixer is not possible.

1) Remove back cover. Attach power, headphones, dummy load and antenna/signal
source. Set signal source to 10.100 MHz. Set signal tracer/radio to 4.8152 MHz.

(Use listed test settings for other bands from Chart above.)

- Place the tracer/radio input lead on the right side of L2 which is the small blue
square to the right of the crystal filter marked as 180J. Is a tone heard at listed
setting? (See Illustration.)

NOTE – A loud 1 KHz tone will be heard due to the 4.9152 MHz BFO oscillator. As you
adjust the signal source, a second, weaker, tone will be heard. This second tone is the
output of the first mixer after passing through the filter. This second tone will vary in
frequency as you adjust the signal source. The louder (BFO) tone will not change
regardless of signal source setting.

-No second tone is heard. See item A.

-Yes, second tone heard. End Test: First mixer appears to be functional.

(A) This test indicates the first mixer is inoperative. If mixing is not occurring, no
mixing product (4.913 MHz signal) will be present. Possible fix: Replace SA612 chip.

Action: Open a trouble ticket with MFJ, request quote for repair if you choose not to
replace chip.

Test Second mixer // Test Audio path:

Test Steps/Results/Action

1) Ensure First mixer has passed test above.

2) Find LM386 (IC3).

-Carefully touch the test lead to PIN 2. (The circuit board trace from this pin
leads to top of Q8). (See Illustration) Is noise like a 60 Hz hum heard?

-A noticeable 60HZ hum is heard in phones. Yes. See item A. End of test.

(A) If the First mixer is good and the audio path is good, this indicates a fault in the
second mixer. If mixing is not occurring, no mixing product (audio) will be present.
Possible fix: Replace SA612 chip.

Action: Open a trouble ticket with MFJ, request quote for repair if you choose not to
replace chip.

Return to ToC

33

Test BFO oscillator

Test Steps/Results/Action:

1) Remove back cover. Attach power, headphones and dummy load. Set signal
tracer/radio to 4.9152 MHz.

- Place the input lead over adjustment VC, this is near the bottom of the crystal
filer. Is a loud tone heard at listed setting?
No. See item A.
Yes? End Test: BFO oscillator appears to be functional.

(A) This test indicates the Beat Frequency Oscillator is inoperative. Possible fix:

Replace second mixer SA612 chip. The crystal is unlikely to be bad.

Action: Open a trouble ticket with MFJ, request quote for repair if you choose not to
replace chip.

Adjust VC to 'center' the BFO to filter pass band:

This adjustment is performed

only

when the receiver has demonstrated very low

sensitivity. Caution must be exercised as the 'wrong' sideband may be peaked.

You really need an accurate RF signal source, an accurate AF signal source and

an O'scope to correctly set the BFO. This is beyond the stated scope of this manual.

If you adjust Vc in an attempt to peak the received signal in the filter passband,

you may peak to the undesired sideband.
Note - To measure the audio output, you will need an AC voltmeter that can read 0 to
1 volt, AC. Output of the radio at full volume is about 0.25VAC into an 8 ohm reactive
load - a speaker. Audio is obtained with a cable connecting TIP to Sleeve or RING to
Sleeve as seen in Operations Manual.

1) With the audio output fed into a speaker, attach the AC voltmeter across the leads
feeding the speaker. With audio present, you should measure up to 0.25 VAC.

2) Set the VFO to one of the listed test frequencies, for example, 10.100 MHz.

3) Using your signal source, (adjust for a 700 Hz tone for best results), peak the
voltmeter reading. You will see at least two peaks.

4) Using a non-metallic tool, adjust Vc for peak. Note direction you move the
adjustment.

5) Attach an antenna and seek a SSB signal. If you can tune a signal with clarity, you
are on the correct sideband.

Return to ToC

34

6) If you cannot tune a SSB signal with clarity, repeat Steps 3 and 4, this time, move
the adjustment in opposite direction. Repeat Step 5.

Results: If tuned correctly, Minimum Detectable Signal (MDS) of 0.1 to 0.2 microvolts
are measured.

Normally, this is set at the factory owing to the need for precision test equipment. If
you are unable to obtain a MDS of 0.2 uV, contact MFJ for a repair quote.

Test SWR protection diode:

If the SWR diode is shorted, the DC supply is grounded. The in-line fuse will blow
repeatedly.

1) With power supplied, check anode of diode to see if supply voltage is present. See

illustration.

Results: If shorted, replace the diode. Since this is a Zener diode, you can only check
for the supply voltage with the test equipment called out. If the diode is open, it will
have no effect on the transmitter, but damage from high VSWR is now very possible.

Bypass Band Module for RX path:

If the Band Module is defective, both receive and transmit are affected. However, a
fault in a Band Module is very unlikely. Given that the Module is made entirely of
passive devices, that is, coils, capacitors and a resistor, the most likely fault is a
soldered connection gone bad or header pin issue related to rough handling.

You do have an in-line fuse for your power cable, yes

?

You will need a short double-ended test lead – one with alligator clips at each end as
shown in illustration. A 4.7K ohm resistor (1/8 watt), a set of pins and a known good
signal source are required.

To bypass the Band Module on the main circuit board,

1) Remove knurled screws, remove back cover. Remove Band Module.

2) Attach headphones and dummy load. Set signal source connected to dummy load to
the same frequency as shown on VFO display. Use your tracer/radio to confirm signal
source is on the correct frequency. In this example, set VFO and signal source to

10.100 MHz.

3) With power removed, insert the leads of a 1/8 watt, 4.7K ohm resistor into the 8 pin
header socket for pins 1 and 2.
On power up, the VFO display will indicate a 30 Meter Band Module is installed. Set
VFO to 10.100.
NOTE – for other bands, see the Chart for resistor value.

4) Using the test lead, and a set of pins – jumper between [the 8 pin header] pin 7 or 8
and [the 6 pin header], pin 1. See Illustration.

in receive only

:

35

Ohms Test for Q10

B to E

E to B

B to C

C to B

C to E

E to C

Low

High

Low

High

High

High

Result: You should hear a tone in your headset. Removing the jumper should kill the
signal.

If the Module is faulted – contact MFJ Enterprises for the appropriate replacement.

Testing Q10 with Ohm meter

Transistors act like diodes when checked with an VOM set to lowest range (1 X). By
swapping the leads, you should see a major change in the ohms measured. Once the
transistor has been removed from the main circuit board, confirm Q10 status with this
test.

1 is Base, 2 is Collector and 3 is the Emitter.

So, for the first column - Positive lead on meter (Red) is the first letter - B

Negative lead of meter (Black) goes on the second letter - E. (Red on lead 1, black on
lead 3).

Then swap the meter leads – Red is now on lead 3...Black lead on 1 See chart below.

Low = 1 to 10 ohms..

High = Many ohms to infinite.

If you fail to obtain these reading, Q10 is likely faulted. Replace Q10.

36

Return to ToC

Basic Maintenance and Repair of the radio:

Common steps for every Task.

1) Tuning Band Modules for best performance.

2) Remove main circuit board from chassis.

3) Install main circuit board back into chassis.

4) Minimum checks before power up after maintenance.

5) Replacement of DC feed protection diode

6) Replacement of Q10 (transmitter final)

7) Replacement of DDS encoder.

8) Replacement of display module. (Display screen)

9) Replacement of Volume potentiometer.

Return to Main ToC

37

Basic Maintenance and Repair of the radio Tasks

Task preparation – a common set of steps for every Task:



Read the entire Task

in advance to ensure you understand what is required, that
you have the correct items (parts and tools) and space on hand to perform the
Task.

 Clear work area and set up ESD-safe work surface.
 Set out required tools (and solder, pump, etc)
 If required by the Task, plug in ESD-safe soldering iron to begin heating to

operating temperature.

 Don safety glasses.

Return to Basic Maintenance ToC

38

TASK 1 – Tuning Band Modules for best performance.

Required by:
Task performed to ensure radio sensitivity is at maximum possible at selected
frequency.

Tools required:

 Non-metallic miniature screwdriver or non-metallic hex head tuning tool, as

appropriate.

 Voltmeter, AC. 0 to 1 or 0 to 3 VAC range, 0 to 1 VAC preferred.

Begin Task:
Step 1: Determine

preferred

operating frequency for the Band Module installed.

NOTE – For the 30 Meter band and module, the common QRP calling frequency is

10.106 MHz, for 20 Meters it is 14.060 MHz. Peaking the Band Module for a preferred
frequency ensures best possible sensitivity for operation. If you will use the -9200
primarily on an established net, then use that net frequency for this Task. The turning
is fairly broadband

Step 2: Remove back cover. Attach 8 ohm speaker, power and dummy load. Feed
signal source to radio via the dummy load.

Step 3: With the speaker attached, connect AC voltmeter leads

across

the speaker

terminals.

CAUTION

– DO NOT use the voltmeter as the only audio load, damage to audio sub-

system may result.

Step 4: Turn on radio, set VFO to desired frequency. Turn up volume until the
voltmeter indicates something.

Step 5: Adjust slugs in T1 and T2 for maximum (peak) indicated voltage. See

Illustration for location of T1 and T2. The radio will produce about 0.25 VAC into an 8

ohm load.

NOTE - The adjustments affect one another, take your time. After adjustment of either
slug produces no increase in measured voltage, turn off radio.

Step 6: Repeat as necessary for each Band Module.

Step 7: Replace back cover.

END OF TASK

Return to Basic Maintenance ToC

39

TASK 2 – Remove main circuit board from chassis:

Required by:
Task performed to gain access to front of main circuit board for replacement of devices
or parts.

Tools required:

 Adjustable spanner.
 Screwdriver, Phillips head. One small, one medium.
 Safety glasses.
 Soldering iron (ESD-safe).
 Solder pump or solder wicking.
 Small container to hold parts as removed.

Begin Task:
Step 1: Using the small Phillips head screwdriver, loosen VFO knob setscrew found
on the side of the knob. DO NOT remove the setscrew, only loosen enough to remove
knob. Remove knob. Place knob in container.

Step 2: Using fingers, gently remove the volume control knob by pulling straight up.
Place knob in container.

Step 3: Turn unit over on face and remove two knurled screws. Set the screws in
the container. Remove back cover. Set cover aside, out of the way.

Step 4: Remove installed Band Module. Place in container.
Step 5: Using soldering iron and pump/wicking, remove solder bridge between main

circuit board pad labeled ANT and center conductor of BNC Connector. DO NOT
unsolder the washer/ring under the BNC connector retaining nut. (see Illustration )

Step 6: Using adjustable spanner, carefully remove the BNC connector retaining
nut. Remove BNC connector by pulling it away from chassis. Use care not to disturb
tabbed washer that is soldered to main circuit board. Replace retaining nut & star
washer on BNC connector and place in container.

Step 7: Using medium Phillips head screwdriver and adjustable spanner, remove
mounting screw & nut holding Q10 power transistor to chassis. (see Illustration ).

NOTE –

Carefully

remove stepped insulating washer and thermal insulator (both are

white) and place in container. Screw nut onto mounting screw and place in container.
Step 8: Using adjustable spanner, remove hex-shaped support posts on each side

of main circuit board. Set these posts in container. (see Illustration )
Step 9: Carefully remove main circuit board by pulling up. You may need to rock

the board slightly to clear the Phone/Key jacks. Don't be in a hurry here; the board will
come out with

little

real force required. Set the chassis with the cover removed in Step

3.

END OF TASK

40

Return to Basic Maintenance ToC

Task 3 – Install main circuit board back into chassis

Installing main circuit board is nearly the opposite of removing the board.

Step 1: Carefully insert main circuit board in chassis, tilted at slight angle to clear both
the encoder/Volume pot and the Phone/Key connectors.

You may need to rock the board slightly to clear the Phone/Key jacks. Don't be in a
hurry here; the board will go in with

little

force required. Loosely install both the Hex

shaped support posts. (see Illustration)

Step 2: Using medium Phillips head screwdriver and adjustable spanner, mount screw
& nut holding Q10 power transistor to chassis.

evenly behind the Q10 mounting tab.

Inset screw and insulated step washer in chassis.

Ensure the heat conducting insulator is

Add nut and tighten the screw, but to not tighten firmly. (see Illustration)

CAUTION – both the step washer (insulator) and heat conducting insulator are

required, otherwise, the power supply is shorted to ground.

Step 3: Install BNC connector by inserting it into the chassis. Use care not to disturb
tabbed washer that is soldered to main circuit board. Replace retaining nut & star
washer on BNC connector. The star washer goes behind the tabbed washer.

Tighten BNC connector nut carefully with adjustable spanner. The center conductor of
BNC should almost touch ANT pad on main circuit board.

Step 4: Carefully tighten down screw holding the stepped washer on Q10. Carefully
tighten down the Hex shaped support posts. DO NOT over-tighten either of these –
damage to board may occur.

Step 5: Build a solder bridge between center conductor of BNC and the ANT pad.

Check your work for solder bridges/splatter that might short out the DC supply, etc.

Step 6: Install Band Module. Replace back cover.

END OF TASK

Return to Basic Maintenance ToC

41

Task 4 – Minimum checks before power up after maintenance

1) Ensure no solder bridges exist. Remove any small bits of wire or solder that might
be loose on either side of the main circuit board. A small brush may be used to clean
with. Use a bright light and magnifying glass to examine area where you performed
any soldering task.

2) The Q10 screw should be tight, with the white stepped washer in place to insulate
the screw. The white insulating heat transfer sheet MUST be in place and appear
symmetrical on all sides of the heat sink for Q10. Without these items (washer and
sheet) Q10 will ground out the DC supply.

3) The Hex-shaped stand-offs should both be in place and snugly fit. CAUTION - Apply
too much pressure and you

will

damage the main circuit board.

4) Attached dummy load, headphones and power cable.

(see illustration)

Task 5 – Replacement of DC feed protection diode

1) Using solder wicking and soldering iron, remove the installed diode, if open. If
shorted, this diode has no practical effect on the operation of the radio. Only the loss
of reverse polarity protection is the issue.

2) Solder in replacement. Inspect area for solder bridges or splatter.

3) Recommend cleaning the area after soldering with 91% iso-alcohol to remove any
residual flux. .

4) Re-install main circuit board back into chassis per Task 3 above.

NOTE - Use of the listed diode is important. Any Schottky Rectifier rated at for least 20
V and 1.0 Amp will work. The reason for a Schottky diode is the low voltage drop
found on these type of devices. Any quality rectifier, even one with axial leads may be
pressed into service. Common power diode will work as the cost of the voltage lost
across the device.

Return to Basic Maintenance ToC

42

Task 6 – Replacement of Q10 (transmitter final)

1) Ensure you purchased the correct transistor. Most are plainly marked.

2) Remove main board from chassis as defined in Task 2 above.

3) Carefully note the size of any gap under Q10 and the main circuit board. This is
essential when replacing the main circuit board – the hole in Q10's heat sink must line
up with the hole in the chassis.

4) Using solder pump or wicking - heat, then clear solder on all three tabs of the
transistor. Once cleared, the transistor should be easy to remove. You may have to
reheat the area – use caution not to damage the board.

5) With Q10 off of the main circuit board, test transistor as shown.

6) Trim leads on replacement transistor to match the length of the leads on transistor
removed from main circuit board. You may need to trim the sides of the replacement –

see photo.

7) Carefully solder replacement Q10 onto main circuit board. Examine are to ensure
there are no solder bridges between circuit pads.

HINT - If you worry about overheating the replacement Q10, clip a piece of

damp

paper

toweling around the transistor while heat is applied to act as an additional heat sink.

Initial Test –

-Using a pair of clip test leads, attach a 1 watt, 51 ohm resistor between the ANT pad

and a grounding point.

-Tune tracer/radio to a listed test frequency (example – 10.100 MHz)

-

Briefly

key transmitter. A very loud tone should be heard. This confirms Q10

operational. If a wattmeter is available, confirm at least 5 watts output @ 12.8VDC

8) Re-install main circuit board back in chassis per Task 3 above.

Return to Basic Maintenance ToC

43

TASK 7 - Replacement of DDS encoder

1) Ensure you purchased the correct encoder..

2) Remove main board from chassis as defined in Task 2 above.

3) Using soldering wick and ESD-safe soldering iron, unsolder encoder. Remove the
encoder from the board. Using this, confirm lead spacing of replacement matches item
removed.

NOTE - A solder pump is recommended for removing solder from mounting tabs.

4) Solder in new encoder. Examine your work to ensure no solder bridges are present
between pins.

5) Connect power, phones and dummy load. Confirm encoder changes the VFO per
Operations manual. Remove cables.

6) Re-install main circuit board back into chassis per Task 3 above.

Return to Basic Maintenance ToC

44

TASK 8 - Replacement of display screen

1) Ensure you purchased the correct display. The logic (driver) for the screen is
embedded in the display module.

2) Remove main board from chassis as defined in Task 2 above.

3) Using soldering wick and ESD-safe soldering iron, unsolder display pins from
module. Remove the display module.

4) Solder in new display. Use ESD handling practices with display module.

CAUTION! Several of the display module pins lead

directly

to MCU. Use of ESD-safe

iron will help prevent damage to MCU.

5) Examine your work to ensure no solder bridges are present between pins. Clean
under display module to ensure no loose solder splatter is present.

6) Connect power, phones and dummy load. Confirm Display changes as set by VFO
per Operations manual. Remove cables.

7) Re-install main circuit board back into chassis per Task 3 above.

Return to Basic Maintenance ToC

45

TASK 9 - Replacement of Volume potentiometer

1) Ensure you purchased the correct potentiometer (1K ohm).

2) Remove main board from chassis as defined in Task 2 above.

3) Using soldering wick and ESD-safe soldering iron, unsolder all potentiometer pins.
Remove the potentiometer from the board. Using this, confirm lead spacing of
replacement matches item removed.

NOTE - A solder pump is recommended for removing solder from mounting tabs.

4) Solder in new potentiometer. Examine your work to ensure no solder bridges are
present between pins.

5) Connect power, phones and dummy load. Confirm potentiometer changes the
volume. Remove cables.

6) Re-install main circuit board back into chassis per Task 3 above.

Return to ToC

46

Item / Label

Nomenclature

Description

DDS encoder w/switch

Encoder, rotary, mechanical

(confirm shaft length)

(Bourns) Mouser P/N

652-PEC11R-4215F-S24

Display

Display, 8 character, 2 lines, 5
VDC

CORE Electronics
SKU- LCD 11122
Basic 8x2 Character LCD
Black on Green 5V ///////
MIDAS P/N MC20805B6W­FPTLW LCD, 2X8, FSTN, WHITE
LED B/L 5V (MIDAS)

Volume control

rotary potentiometer
1K liner taper

Mouser P/N
688-RK09D1130C2P

5 volt buss regulator78L05

Voltage regulator +5 VDC
SOT89 pkg

78L05 Newark P/N 77C1856

6 volt buss regulator 78L06

Voltage regulator +6 VDC
SOT-89 pkg

78L06 Newark P/N 37X9027

IC 1, IC 2

Mixer

double balanced mixer &
oscillator, SMT type SA612A

SA612A
Newark P/N 26M2818
(SA602 is a suitable substitute

IC 3
Audio amplifier

amplifier, audio, 8 pin, SMT
type, DIP LM386

LM386 Newark P/N 41K5099

IC 4 MCU

32-Bit Microcontroller IC, 48K
memory, 74 MHz clock speed

PIC16F73-1/60 (Microchip brand)
Newark P/N 86W6451

IC 5 DDS

Direct Digital Synthesis

AD9834 Newark P/N 28M4203

IC 6 VFO scratch pad memory

4K EEPROM 93C66A

93C66A (Microchip brand)
Newark P/N 61H6598

IC 7 Keyer

(must be programmed)

CMOS Flash-based 8-bit
microcontroller 12F629

12F629 (Microchip brand)
Newark P/N 61K3433

D 6

Zener diode, SWR protect

Schottky Rectifier, 36 V, SMD

Vendor

Mouser P/N

771-BZX84J-B36,115

Nexperia P/N
BZX84J-B36,115

D3

Surface Mount Schottky
Barrier Rectifier

SS12, diode Multicomp brand
Newark P.N 90R9168

Q1, Q2, Q3, Q4, Q5, Q7, Q8

Switching transistor –multiple

.1Amg (1AM) NPN Silicon
Epitaxial Planar Transistor
Switching, TO-23 SMT type
2N3904

Taitron P/N MMBT3904

Q6

marked 7KXNF (7K)
Transistor 2N7002K

Fairchild Semiconductor
Mouser P/N 512-2N7002K

Q9

marked t1P (1P)
2N2222/2N2222A SOT-23

Mouser P/N 512-MMBT2222A
Q 10 Transmitter PA

RF power transistor, NPN TO-

2SC2078

Data for system components

47

220 pkg

Futurlec P/N2SC2078

Item / Label

Nomenclature

Description

J1, DC input jack

2.1 mm coaxial, PC mount

DC-9 P/N FC68146)
CLIFF brand

J2, internal battery header

2-Pin, 2.54mm spacing,
polarized

CuteDigi –
SKU POL_CON_254_2_J11

Jack – Phone

3.5MM PC horizontal mount
Jack, stereo, non-threaded
bushing

Switchcraft
P/N 35RAPC2BHN2

Jack – Key

3.5MM PC horizontal mount
Jack, stereo, non-threaded
bushing

Switchcraft
P/N 35RAPC2BHN2

Crystal, filter, ladder

4.9152 MHZ (matched) 4
each

Digikey P/N X084-ND
ECS P/N ECS-49-20-1

Crystal, 2nd mixer BFO

4.183 MHz (front of board)

DDS source clock

Oscillator, DIP package

HOSONIC brand HSC-33B/D726
60 MHz, 5 DC

L1

L2

Band

R1 value

marked

Takes Pin 1
to ground

14 turns

13 turns

80

473

11

12

40

223

11

12

30

103

7 9

20

472

7 9

17

222

7 9

15

101

THE MCU (PIC Controller) Keyer and VFO Memory chips require programming code that

I do not have access to

– the parts are included in the listing above, but must be

programmed prior to replacement.

Additional parts identification Band Modules

Return to ToC

48

Ground to the tab
under BNC connector
nut.

Test Point

+5VDC

+5VDC

Adjustment

Test Point
for switch

Test Point

+6VDC

Test Point
Rear of J1

Illustrations

DC Power Test Points, adjustment and protection

Q10 mounting nut.

Return to DC Test Steps

Return to ToC

49

Pin 1

Pin 8

Pin 1

Pin 6

T 1

T 2

L 1

L 2

Transmit

Filter

Receive

Filter

Illustrations

Band Module, top
80 Meter

50

Return to ToC

60 MHz

oscillato
r

MCU

PIC chip

DDS
chip

VFO

memory

chip

These 12 pins
(to the right of the T)
feed the digital display

Illustrations

DDS / VFO sub-system

51

Return to ToC

J3 – Key jack
CQ button

Volume Control pins – Center pin feeds J4 (Phones)

Keying system

Return to ToC

52

Pins 1 and 2.

D6, SWR protection diode

L8

Band Module Bypass

L8 test point for supply voltage.

53

Return to ToC

TIP

RING

Sleeve

Pin 1 Six pin

test point

First mixer SA602

Test point for

1st mixer

Test point for

LM-386

Adjustment VR

for BFO

Pin 1 & 2 for

8 pin header

4.7K Resistor
goes here

Pin 1

Ohmmeter test points

for Phones jack

Illustrations

Main Receiver components & signal path

54

Return to ToC

PIN 2
PIN 1

PIN 16
PIN 15

PIN 2
PIN 1

Illustrations

Digital Display Screen 8 Characters x 2 Lines

Pin 1 – Signal ground for data

Pin 2 - + power for embedded logic

Pin 3 – Contrast adj

Pin 11-14 – data buss lines

Pin 15 – LED +5 line (backlight)

Pin 16 – LED - line

Main Board, back view of Display pins.

NOTE – Four of the data pins connect directly to the MCU – ESD techniques apply!

Return to Display test.

55

These standoffs must be removed for main
board to be removed.

Steve, M0SHM, sent these photos showing how he had to mod (slightly) the pins on a new
2SC2078 to fit it to his rig. He was kind enough to share these photos and allow use here.

Trim leads of Q10 as needed, use a fine file and take your time.

56

Hints, Tips, Kinks

Recommended items not supplied with radio set.

These are items I've added to my 'kit' to carry with the radio all the time. When
operating outside of the shack, I make notes in my log about items I wished I brought
along or needed. Here are some of those noted items:

 Adapter BNC male to BNC male. I use this with my home-made dummy load.
 Adapter BNC Female to SO239. MFJ-7708 (P/N 610-2008). May allow you to

use someone else's existing antenna system.

 Cable, jumper, BNC to BNC. To connect to an external antenna tuner. You may

need an adapter BNC Female to PL-259, depending on the tuner.

 Jameco P/N GSE 231015: Cable ASM RG58/U 15 Foot BNC to BNC 50 Ohm M-

M.

 Adaptor, BNC To Dual binding posts MFJ-7704 (P/N 610-2106). Allows you put

up a makeshift antenna.

KK6FVP uses these cleverly modified adapters for an antenna feed. Hook up your wire
to the post for a dipole and hoist into a tree. The split rings carry the weight of the
wire, saving wear on the binding post. Use a BNC to BNC cable and the adapter isn't
required.

Image Copyright 2015 KK6FVP, All Rights Reserved, Used with permission

Return to ToC

57

Thoughts on building a portable DC power system

An easy place to start is with a MFJ-5513 - power cable, 2.1mm,-open end, 3 ft (MFJ P/N 620-8321). This will fit the ­9200 and allow you enough cable to park your battery pack someplace convenient. Like, inside your parka to keep the
batteries warm in inclement weather.

ALWAYS

Add a "Holder, battery, "AA", for either 8 or 10 cells. I use both, but if I'm going out where there is no power for a
charger, the 8 cell holder is my first choice. It allows use of NiMH rechargeable batteries for a 9.6 volt source or "AA"
primary cells, for a 12VDC+ power source. The -9200 is happy with anything over 8 volts, so all you see is somewhat
reduced power out with the NiMH cells.

A 10 cell holder gives me a full 12VDC+ with the rechargeable cells, but would provide over 15 volts with primary "AA"
cells –
my NIMH cells on the road. The cell holders are just a couple of dollars. A rubber band on the outside to keep the cells
in place and you're ready to travel.

For extreme cold weather,
Lithium primary cells at 3.6 VDC @ 2.4 aH that will work in a 3 or 4 cell holder – price is a major consideration here as
the cells cost up to 3 dollars - per cell. If

I bought my cell holders on line because the output of the pack is a polarized connector – one that looks just like the
top of a 9 volt battery. That was by design.

A single 9 volt battery will power the -9200 long enough for a few contacts or some extended listening to shortwave
stations. I see this as maximum flexibility.

A connector for the power cable is easily had. Take a dead 9V battery and peel off the foil on the outside. You
discover a set of very small 1.5 volt batteries and a ready-made for your cell holder connector. Solder this connector to
your power cable, put some insulating tape over the soldered connections and you're in business.

With this setup I can run primary cells, rechargeable cells or to save weight on a hike, just carry a couple of 9 volt
batteries for a few quick QSO's. All with the same, polarized, power cable.

The 9200 has an internal power connector - a header, really. If you find an appropriate
there is room for two or three paralleled 9 volt batteries inside the radio. This may appeal to you, if so, ensure you both
insulate the batteries and secure them so the Band Module doesn't get bashed.

put in-line fuses on any power cable. Use at least a 1.5 ampere fuse for this cable.

not good

. So – I have both...an eight cell holder for either type and a ten cell holder when I know I can recharge

Lithium-Iron

1.5 volt "AA" cells are now available at reasonable prices. There are also

weight

is your primary consideration, these are worth a look.

I cannot stress enough to USE A POLARIZED battery connector.

polarized

2 pin connector,

58

Finally, a thought about LiPO batteries. The AA sized 14500 series are 3.7 VDC at almost 2.4 aH capacity – that's no
typo. 2.4 amp hours. So, a 3 cell (11.1 VDC) or a 4 cell (14.8VDC) battery pack with that amount of power density has
some appeal. Keep in mind LiPO cells require
monitored while under charge. Read more about these cells and related hazards elsewhere or on line.

Alternatively, if you are already using Anderson Power Pole DC connectors, there is the MFJ-5513M power cord with
the Power Pole connectors. Simply carry what you already have.

I've been asked why I seem to be such a fan of AA batteries for powering this rig. Simple, AA batteries are just about
universally available

For example, I was working an oil spill clean-up project in the Komi Republic, part of the old Soviet Union. This was in
1995, just after the old Soviet fell apart. Despite being in an isolated town, quite literally at the end of the railroad line on
the Arctic Circle, I never had any issues finding fresh AA batteries for my shortwave set. I've been a fan ever since.

The genesis of the MFJ-9200:

When I first made the decision to purchase the 9200, I was struck, as are many, by the similarity of this radio to the You
Kits HB-1x series of radios. There is a good reason for that. The MFJ-9200 is a clone of a clone of the HB-1A.

A variant of the HB-1A was offered. Several foreign (Non- North American) web sites started chatting about an "HS-1A"
radio kit. I first saw this on a site where the entry was dated 8/2011. It talked of BD4RG's upcoming HS-1A CW
transceiver.

world-wide

.

exquisite care

in charging and use. These cells should

Ensure you add an in-line fuse

always

.

be

I found further info and some images on a Japanese web site that tied the HB-1A and the HS-1A directly together – the
HS stood, it was said, for
modules would provide the needed filtering. Now very interested, I dug around even more.

I found some nice, high definition images of the HS-1A and compared it to the original MFJ-9200. You can see the
resemblance with little effort. The software splash screen on the "B" board version of 9200 comes up as 8/2011.

On these
9200 (the A model) fared badly.

Reviews were
IOW, the receiver was a dud. The next 9200, the B model seems to have solved most of the issues seen in early reviews.
I have people still send me emails that often complain of birdies, but it seems less often than before.

59

early

"A" board version of the 9200, the splash screen, first seen at power on, displays HS-1A. The original

uncomplimentary

Single

band. The HS-1A was offered as an even lower cost single band transceiver. Band

and complained of poor sensitivity and very low audio. Birdies were also a complaint.

Once sorted out, the 9200 is a very nice radio with a hot (.1 to .2 uV for MDS) receiver and a solid transmitter. In
addition, I see the newest HB-1B, the MKIII uses the same PA setup as the 9200. Here are the photos that layout the
evolution of the 9200.

HS-1A and HB-1A side and side. Larger shot of the HS-1A splash screen on an "A" model 9200 (Thanks to Steve, K7EW)

HS-1A main board – rear and front. D-9, the SWR diode is on the face of the board and is an axial version. The
broadband transformer (T-1) feeding Q-10 is also found on the front of the board.

60

9200 B Model PA section.

HB-1B MK III PA section – both use the same 2SC2078. Much cleaner that the earlier HB-1Bxx series.

To be completely honest, the build quality of the HB-1Bx is better than the 9200. No hand soldered parts as seen on the

9200. The 9200 is still, however, relay free.

61