Mettler Toledo XSR10001L, XSR10001L/A, XSR1202S, XSR1202S/A, XSR16000L/A Instruction Manual

User Manual

Precision Balances

XSR models

Overview balances with S weighing platform

3

4

1

2

2

5

6

8

3

9

10

8

10 9

7

11

2

3

6 7

5

4

Legend balances with S weighing platform

MagicCube Draft Shield

1

DripTray

2

SmartPan weighing pan

3

Weighing pan

4

MagicCube Draft Shield top door

5

Overview interface board S weighing platform

MagicCube Draft Shield side door

6

MagicCube Draft Shield side door handler

7

Weighing platform with protective cover

8

Leveling foot

9

Terminal with protective cover

10

Legend interface board S weighing platform

Ethernet port

1

USB device ports

2

Fixations for optional terminal stand

3

Service seal

4

USB host port

5

Socket for terminal connection cable

6

Socket for AC/DC adapter

7

Overview balances with S weighing platform 3Precision Balances

Overview balances with L weighing platform

11

22

3344

11 22 4

5

6

3

Legend balances with L weighing platform

Weighing pan support cap

1

Weighing pan

2

3

4

Leveling foot

Terminal with protective cover

Overview interface board L weighing platform

Overview balances with L weighing platform4 Precision Balances

Legend interface board L weighing platform

Socket for AC/DC adapter

1

Socket for terminal connection cable

2

Service seal

3

4

5

6

USB host port

USB device ports

Ethernet port

Overview terminal

11

22

33

4455

66

77

88

Legend Terminal

No. Key Name Explanation

1 Methods Opens the section Methods.

2 Protocol Opens the section Protocol.

3 Balance menu Opens the section Balance menu.

4

5

6

7

8

Home To return from any menu level to the method work screen.

Zero Zeroes the balance.

Tare Tares the balance.

- 4.3 inch capacitive
TFT touchscreen

ON/OFF Switches the balance on/off.

The balance must always be zeroed before starting the
weighing process. After zeroing, the balance sets a new zero
point.

This function is used when the weighing process involves
containers. After taring the balance, the screen shows
which indicates that all displayed weights are net.

The touchscreen shows information about the current weighing
process.

By tapping on the button
switched off but goes into standby mode. To switch the
balance completely off, it must be unplugged from the power
supply.

Note

Do not disconnect the balance from the power supply unless
the balance is not used for an extended period of time.

, the balance is not completely

Overview terminal 5Precision Balances

1 Safety Information

• Read and understand the instructions in this manual before using the balance.

• Keep this manual for future reference.

• Include this manual if you pass on the balance to other parties.

If the balance is not used according to the instructions in this manual or if it is modified, the safety of the
balance may be impaired and Mettler-Toledo GmbH assumes no liability.

Finding more information

Additional information about this balance can be found in the Operating Instructions on the CD­ROM or online.

u www.mt.com/XSR-precision-OI

u www.mt.com/library

1.1 Definition of signal warnings and symbols

Safety notes are marked with signal words and warning symbols. These show safety issues and warnings.
Ignoring the safety notes may lead to personal injury, damage to the instrument, malfunctions and false
results.

WARNING

CAUTION

NOTICE

for a hazardous situation with medium risk, possibly resulting in death or severe
injury if not avoided.

for a hazardous situation with low risk, resulting in minor or moderate injury if not
avoided.

for a hazardous situation with low risk, resulting in damage to the instrument, other
material damage, malfunctions and erroneous results, or loss of data.

General hazard Electrical shock

1.2 Product safety information

Intended use

This balance is designed to be used in laboratories by trained staff. The balance is intended for weighing
purposes.

Any other type of use and operation beyond the limits of technical specifications without written consent from
Mettler-Toledo GmbH is considered as not intended.

General safety information

This balance complies with current industry standards and the recognized safety regulations; however, it
can constitute a hazard in use. Do not open the balance housing: The balance contains no user-serviceable
parts. In the event of problems, please contact a METTLER TOLEDO representative.

Always operate and use your instrument only in accordance with the instructions contained in this
document. The instructions for setting up your new instrument must be strictly observed.

If the instrument is not used according to the Operating Instructions, protection of the instrument may
be impaired and METTLER TOLEDO assumes no liability.

Staff safety

This printed document must be read and understood before using the balance. This printed document must
be retained for future reference.

The balance must not be altered or modified in any way. Only use METTLER TOLEDO original spare parts
and accessories.

Safety Information6 Precision Balances

Safety notes

WARNING

Danger of death or serious injury due to electric shock!

Contact with parts that contain a live current can lead to injury and death. If the balance
cannot be shut down in an emergency situation, people can be injured or the balance can be
damaged.

1 Only use the original universal AC/DC adapter delivered with your balance.
2 Check that the voltage printed on the balance is the same as your local power supply

voltage.
ð If this is not the case, under no circumstances connect the AC/DC adapter to the power

supply, but contact a METTLER TOLEDO representative.

3 Only plug the adapter into a socket which is grounded.

NOTICE

Damage to the balance due to wrong usage.

1 Only use indoors in dry locations.
2 Do not use pointed objects to operate the touchscreen.
3 Only use original METTLER TOLEDO accessories and peripheral devices.
4 Do not open the balance housing. It contains no user-serviceable parts. Contact a

METTLER TOLEDO representative in case of any issue.

Safety Information 7Precision Balances

2 Basic Navigation

2.1 Main sections at a glance

The method work screen shows information about the current weighing process and the selected method
(the picture shows the method work screen of the method General Weighing). The sections Methods,
Protocol and Balance menu can be opened by tapping on the corresponding button on the right hand side
of the touch screen.

No. Section Name Explanation

1 Methods In the section Methods new methods can be defined or

2 Protocol In the section Protocol the stored weighing results for the

3 Balance menu In the section Balance menu system settings can be adjusted

existing methods can be edited. Furthermore, routine tests to
check the accuracy of the balance and adjustment procedures
can be defined and started.

currently active method are shown.

and information about the balance and precedent tasks are
shown. Furthermore, the menu provides a procedure to level
the balance.

Basic Navigation8 Precision Balances