1 Shut off gas to the appliance.
2 Extinguish any open flame.
3 Open lid
4 If odor continues, keep away from the
appliance and immediately call your
gas supplier or your fire department.
Failure to comply with these instructions could result in a fire or explosion that could cause serious bodily
injury, death, or property damage.
Combustion by products produced when using this product contain chemicals known to the States of
California to cause cancer, birth defects, or other reproductive harm
Your grill will be very hot. Never lean over the cooking area while using your grill. Do not touch cooking
surfaces, grill housing, lid or any other grill parts while the grill is in operation, or until the gas grill has
cooled down after use.
Safety Instruction
WARNING
1.Do not store or use gasoline or other
flammable liquids or vapors in the vicinity
of this or any other appliance.
2.An LP cylinder not connected for use
shall not be stored in the vicinity of this or
any other appliance.
2
Safety Instruction continued
WARNING
ELECTRICAL GROUNDING INSTRUCTIONS This appliance (light & rotisserie motor) is equipped with a plug and should
be plugged directly into a properly grounded receptacle. When installed, must be electrically grounded in accordance with
local codes or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical
Code, CSA C22.1 DO NOT cut or remove the grounding prong from this plug.
1.To protect against electric shock, do not immerse cord or plugs in water or other liquid.
2.Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.
3.Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance malfunctions
or has been damaged in any manner. Contact the manufacturer for repair.
4.Do not let the cord hang over the edge of a table of touch hot surfaces.
5.Do not use an outdoor cooking gas appliance for purposes other than intended.
6.When connecting, first connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.
7.Use only a Ground Fault Interrupt (GFI) protected circuit with this outdoor cooking gas appliance.
8.Never remove the grounding plug or use with an adapter of 2 prongs.
9.Use only extension cords with a 3 prong grounding plug, rated for the power of the equipments, and approved for
outdoor use with a W-A marking.
WARNING
Do not try lighting this appliance without reading the
“LIGHTING INSTRUCTIONS” section of this manual.
TESTED IN ACCORDANCE WITH ANS Z21.58 CSA 1.62007 STANDARD FOR OUTDOOR COOKING GAS
APPLIANCE. THIS GRIL IS FOR OUTDOOR USE ONLY.
Grill Installation Codes
Check your local building codes for the proper method of
installation. in the absence of local codes, this unit should be
installed in accordance with the National Fuel Gas
Code ,ANSI Z223.1/NFPA 54,Storage and Handling of
Liquefied Petroleum Gases, ANSI /NFPA B149.2 or CSA
B149.1 Natural Gas and Propane Installation Code, and the
National Electrical Code, ANSI/NFPA 70.
Correct LP Gas Tank Use
LP gas grill models are designed for use with a standard 20
lb. Liquid Propane Gas tank, not included with grill. Never
connect your gas grill to an LP gas tank that exceeds this
capacity.
If an external electrical source is utilized: The outdoor
cooking gas appliance, when installed, must be electrically
grounded in accordance with local codes or, in the absence
of local codes, with the National Electrical Code, ANSI/NFPA
70, or the Canadian Electrical Code, CSA C22.1.
WARNING
Keep any electrical supply cord and the fuel supply hose
away from any heated surfaces.
CAUTION: Beware of Flashback
CAUTION: Spiders and small insects occasionally
spin webs or make nest in the grill
burner tubes during transit and
warehousing. These webs can lead
to gas flow obstruction, which could
result in a fire in and around burner
tubes. This type of fire is known as
“FLASH-BACK” and can cause serious damage to your grill
and create an unsafe operating condition for the user.
Although an obstructed burner tube is not the only cause of
“FLASH-BACK”, it is the most common cause.
To reduce the chance of “FLASH-BACK”, you must clean the
burner tubes before assembling your grill, and at least once
a month in late summer or early fall when spiders are most
active. Also perform this burner tube cleaning procedure if
your grill has not been used for an extended period of time.
A clogged tube can lead to a fire beneath the grill.
NOTE: The normal flow of gas through the regulator
and hose assembly can create a humming noise. A
low volume of noise is perfectly normal and will not
interfere with operation of the grill. If humming noise is
loud and excessive you may need to purge air from the
gas line or reset the regulator excess gas flow device.
This purging procedure should be done every time a
new LP gas tank is connected to your grill.
Visually check the burner flames prior to each use.
The flames should look like this picture. If they do not,
refer to the burner main tenancy part of this manual.
3
Safety Instruction continued
LP-Gas Supply System
If the information is not followed exactly, a fire resulting in death or
serious injury could occur.
A 20lb tank of approximately 12 inches in diameter by 18-1/4
inches high is the maximum size LP gas tank to use.
This safety feature prevents the tank from being overfilled, which
can cause malfunction of the LP gas tank, regulator and/or grill.
The LP gas supply cylinder to be used must be constructed and
marked in accordance with the specifications for LP –Gas cylinder
of the U.S. Department of Transportation (DOT) or the National
Standard of Canada ,CAN/CSA –B339, Cylinders, Spheres and
Tubes for Transportation of Dangerous Goods and Commission .
The LP gas tank must have a shutoff valve terminating in an LP
valve outlet that is compatible with a Type 1. LP gas supply
cylinder must have a shut off valve terminating in a valve outlet
specified for connection type QCC1 in the standard for compressed
gas cylinder valve outlet and inlet connection ANSI/CGA-V-1 as
applicable. LP gas supply cylinder must be fitted with an Overfill
Protection Device (O.P.D) The LP gas tank must also have a safety
relief device that has a direct connection with the vapor space of
the tank.
The tank supply system must be arranged for vapor withdrawal.
The LP gas tank used must have a collar to protect the tank valve
Place dust cap on cylinder valve outlet whenever the cylinder is
not in use. Only install the type of dust cap on the cylinder valve
outlet that is provided wit the cylinder valve. Other types of cap or
plugs may result in leakage of propane
Never connect an unregulated LP gas tank to your gas grill.
This outdoor cooking gas appliance is equipped with a high
capacity hose/regulator assembly for connection to a standard 20lb.
Liquid propane cylinder.
Have your LP gas tank filled by a reputable propane gas
dealer and visually inspected and re-qualified at each filling.
Do not store a spare LP gas cylinder under or near this
appliance.
Never fill the cylinder beyond 80 percent full .
Always keep LP gas tanks in an upright position.
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Storage of an outdoor cooking gas appliance indoors is
permissible only if the cylinder is disconnected and removed from
the outdoor cooking gas appliance..
When your gas grill is not in use the gas must be turned off at LP
gas tank.
•The gas must be turned off at the supply cylinder when the
outdoor cooking gas appliance is not in use.
•LP gas tank must be stored outdoors in a well-ventilated area and
out of reach of children. Disconnected LP gas tanks must not be
stored in a building, garage or any other enclosed area.
•PROPER PLACEMENT AND CLEARANCE OF GRILL
•Do Not obstruct the flow of ventilation air around the gas grill
housing. Only use the regulator and the hose assembly supplied
with your gas grill. Replacement regulators and hose assemblies
must be those specified in this manual.
•The regulator and hose assembly must be inspected before each
use of the grill. If there is excessive abrasion or wear or if the hose
is cut, it must be replaced prior to the grill being put into operation.
The replacement hose assembly shall be that specified by the
manufacturer.
Pressure regulator and hose assembly supplied with the
outdoor cooking gas appliance must be used. Never substitute
other types of regulator. Contact customer service for
manufacturer specified replacement parts.
•This outdoor cooking gas appliance is equipped with a
pressure regulator comply with the standard for Pressure
Regulating Valves for LP Gas ANSI/ UL 144.
•Do not use briquettes of any kind in the grill.
•The grill is designed for optimum performance without the use
of briquettes. Do not place briquettes on the radiant as this will
block off the area for the grill burners to vent. Adding
briquettes can damage ignition components and knobs, and
void the warranty.
•Keep the back and side cart free and clear from debris. Keep
any electrical supply cord, or the rotisserie motor cord away
from the heated areas of the grill.
•Never use the grill in extremely windy conditions. If located in
a consistently windy area (oceanfront, mountaintop, etc.) a
windbreak will be required. Always adhere to the specified
clearance.
•Never use a dented or rusty propane tank.
•Keep any electrical supply cord and the fuel supply hose
away from any heated surface
•While lighting, keep your face and hands as far away from the
grill as possible.
•Burner adjustment should only be performed after the burner
has cooled.
WARNING
Your grill will get very hot. Never lean over the cooking area
while using your grill. Do not touch cooking surfaces, grill
housing, lid or any other grill hot surface while the grill is in
operation, or until the gas grill has cooled down after use.
Failure to comply with these instructions may result in
serious bodily injury.
WARNING
ROTISSERIE DRIVE MOTOR
USE ONLY FOR OUTDOORS, DO NOT EXPOSE TO RAIN.
CAUTION: TO ENSURE CONTINUED PROTECTION
AGAINST RISK OF ELECTRIC SHOCK, CONNECT TO
PROPERLY GROUNDED OUTLETS ONLY. TO REDUCE
THE RISK OF ELECTRIC SHOCK, KEEP EXTENSION
CORD CONNECTION DRY AND OFF THE GROUND.
INSECT WARNING:
Spiders and insects can nest in the burners of this and any
other grill, and cause the gas to flow improperly. This is a
very dangerous condition, which can cause a fire to occur
behind and beneath the valve panel, thereby damaging the
grill and making it unsafe to operate. Inspect the grill at least
twice a year.
WARNING
Keep a spray bottle of soapy water near the gas supply
valve and check the connections before each use.
4
Safety Instruction continued
DO NOT USE ALUMINUM FOIL TO LINE THE GRILL
RACKS OR GRILL BOTTOM.
This can severely upset combustion airflow or trap
excessive heat in the control area.
DO NOT LEAVE THE GRILL UNATTENDED WHILE
COOKING.
SAFETY PRACTICES TO AVOID PER S ONAL INJURY
When properly cared for, your grill will provide safe, reliable
service for many years. However, extreme care must be
used as the grill produces intense heat can increase
accident potential. When using this appliance basic safety
practices must be followed, including the following:
Do not repair or replace any part of the grill unless
specifically recommended in this manual. All other service
should be referred to a qualified technician.
This grill is not intended to be installed in or on recreational
vehicles or boats
Children should not be left alone or unattended in an area
where the grill is being used. Do not allow them to sit, stand
or play in or around the grill at any time.
Do not store items of interest to children around or below
the grill.
Do not permit clothing, pot holders or other flammable
materials to come in contact with or too close to any grate,
burner or hot surface until it has cooled. The fabric could
ignite and cause personal injury.
When using the grill, do not touch the grill rack, burner
grate or immediate surroundings as these areas
become extremely hot and could cause burns. Use only
dry potholders. Moist or damp potholders on hot
surfaces may cause steam burns. Do not use a towel
or bulky cloth in place or potholders. Do not allow
potholders to touch hot portions of the grill rack.
Grease is flammable. Let hot grease cool before
attempting to handle it. Do not allow grease deposits to
collect in the grease tray at the bottom of t h e grill’s
firebox. Clean the grease tray often.
Do not use aluminum foil to line the grill racks or grill
bottom. This can severely upset combustion air flow or
trap excessive heat in the control area.
For proper lighting and performance of the burners
keep the burner ports clean. It is necessary to clean
them periodically for optimum performance. The
burners will only operate in one position and must be
mounted correctly for safe operation.
Clean the grill with caution. To avoid steam burns, do
not use a wet sponge or cloth to clean the grill while it
is hot. Some cleaners produce toxic fumes or can ignite
if applied to a hot surface.
Turn off grill controls and make certain the grill is cool
before using any type of aerosol cleaner on or around
the grill. The chemical that produces the spraying
action could, in the presence of heat, ignite or cause
metal parts to corrode.
For personal safety, wear proper apparel. Loose fitting
garments or sleeves should never be worn while using this
appliance. Some synthetic fabrics are highly flammable and
should not be worn while cooking.
Only certain types of glass, heat-proof glass ceramic,
earthenware, or other glazed utensils are suitable for grill
use. These materials may break with sudden temperature
changes. Use only on low or medium heat settings in
accordance with the manufacturer’s guidelines.
Do not heat unopened food containers. A build-up of
pressure may cause the containers to burst.
Use a covered hand when opening the grill lid.
Never lean over an open grill.
When lighting a burner, pay close attention to what you are
doing. Make certain you are aware of which burner you are
lighting, so your body and clothing remain clear of open
flames.
Do not use the grill to cook excessively fatty meats or other
products which promote flare – ups.
Do not operate the grill under unprotected combustible
constructions. Use only in well ventilated areas. Do not use
in buildings, garages, sheds, breezeways or other such
enclosed areas.
Keep the area surrounding the grill free from combustible
materials including fluids, trash, and vapors such as
gasoline or charcoal lighter fluid. Do not obstruct the flow
of combustion and air ventilation.
WARNING
This outdoor cooking gas appliance is not intended to
be installed in or on boats, and other recreational
vehicles.
5
Please check all the parts before assembling the grill to make sure every parts is ready.
C. Left Side Shelf------------1pc.B. Right Side Shelf----------1pc.A. Body Assembly-------- 1pc.
F. Rotisserie Kit ------------1set.E. Rotisserie Motor----------1pc.D.Rotisserie Motor Bracket------
1pc.
Parts Check List
H. Warmming rack………..1pcG. Battery----------------------1pc.
I. Hook………..3pc
Assembly Instruction
REQUIRED TOOLS & INSTALLATION EXAMPLES
Tighten all screws on the grill as some screws may have loosened during transit
6
Assembly Instruction continued
Side shelf, left and right (Screws has been attached on side shelf or side panel.)
Remove the 3 screws along the t o p
edge of the side shelf.
3x
2x
Loosen the bottom 2 screws
without removing them
completely.
Align the bottom key holes on side shelf with 2 loosened
screws in side panel. Attached the side shelf to the cart
with the two loosened screws on the side panel. Hook the
side shelf onto the two screws.
Tip: This step is meant to help with the installation but do
not depend solely on the two screws to hold the weight of
the side shelf.
7
The top 3 screws insert from
inside the fire box.
3x
Assembly Instruction continued
2x
Hooks
Left side shelf assembly step is same as right side shelf.
Flame Tamers
Before using your grill, please visually check to make sure each
flame tamer is in the correct position. They should be sitting in
between the two grooves for each burner.
8
Assembly Instruction continued
Rotisserie motor and kit , warming rack: (Screws for assembly are attached on motor bracket)
2x
9
Battery
Assembly Instruction continued
To release the tank tray glides, slide
the bracket up 90 degrees.
To lock tank tray glides, slide the
bracket to the left 90 degrees.
Gas tank
Secure the tank with the tightening the bolt
after the tank has been placed in the tray.
10
Loading...
+ 22 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.