Melitta MES2K, MES2W, MES2R, MES2MG, MES2MGCAN User Manual

USE AND CARE GUIDE FOR

MODEL MES2B/W/R/K/MG,

MES2B/W/R/K/MGCAN

READ AND SAVE THESE INSTRUCTIONS

Pod Brewing System

2

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should
always be followed, including the following:

• Read all instructions.

• Do not touch hot surfaces. Use handles or knobs.

• To protect against fire, electric shock, do not place cord, plugs,
or appliance in water or other liquid.

• Close supervision is necessar y when any appliance is used by
or near children.

• Unplug from outlet when not in use and before cleaning. Allow
to cool before putting on or taking off parts, and before cleaning
the appliance.

• Do not operate any appliance with a damaged cord or plug or after
the appliance malfunctions, or has been damaged in any manner.
Contact Consumer Service for examination, repair or adjustment.

• The use of accessory attachments not recommended by the
appliance manufacturer ma y result in fire, electric shock or injury
to persons.

• Do not use outdoors.

• Do not let cord hang over edge of table or counter, or touch hot
surfaces.

• Do not place on or near a hot gas or electric burner, or in a
heated oven.

• To disconnect, turn any control to “off,” then remove plug from
wall outlet.

• Do not use appliance for other than intended use.

• Be certain lid is securely in place before operating appliance.

• Scalding may occur if the lid is opened during the brewing cycles.

SA VE THESE INSTRUCTIONS

THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

3

ADDITIONAL IMPORTANT

SAFEGUARDS

WARNING: This appliance generates heat and escaping steam

during use. Use proper precautions to prevent the risk of burns,
fires, or other injury to persons or damage to property.

• All users of this appliance must read and understand this
Owner’s Manual before operating or cleaning this appliance.

• The cord to this appliance should be plugged into a 120V AC
electrical outlet only.

• Use

water only in this appliance! Do not put any other liquids or
food products in this appliance .Do not mix or add anything to the
water placed in this appliance, except as instructed in the User
Maintenance Instructions to clean the appliance.

• DO NOT attempt to move an appliance containing hot liquids.
Allow appliance to cool completely before moving.

• Keep appliance at least 4 inches a wa y from walls or other objects
during operation. Do not place any objects on top of appliance
while it is operating. Place the appliance on a surface that is
resistant to heat.

• If this appliance begins to malfunction during use, immediately
unplug the cord. Do not use or attempt to repair the malfunc­tioning appliance.

• If this appliance falls or accidentally becomes immersed in water
or any other liquid, unplug immediately.

Do not reach into the
water! Do not use this appliance after it has fallen into or
has become immersed in water.

Contact Consumer Service

for examination and repair.

• Do not leave this appliance unattended during use.

• Always use fresh, cool water in your coffee maker. Warm water
or other liquids, e xcept as listed in cleaning section, may cause
damage to the appliance.

4

POLARIZED PLUG:This appliance has a polar ized plug, (one
blade is wider than the other).To reduce the risk of electric shock,
this plug is intended to fit into a polarized outlet only one way. If
the plug does not fit fully in the outlet, rev erse the plug.If it still does
not fit, contact a qualified electrician. Do not attempt to modify the
plug in any way.

SHORT CORD INSTR UCTIONS:A short power supply cord is pro­vided to reduce the risk resulting from becoming entangled in or
tripping over a longer cord.

Do not use an extension cord with this product.
ELECTRIC POWER: If the electric circuit is overloaded with other

appliances, your appliance may not operate properly. It should be
operated on a separate electrical circuit from other appliances.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT REMOVE THE BOTTOM COVER.NO USER­SERVICEABLE PARTS INSIDE.REPAIR SHOULD BE DONE BY
AUTHORIZED SERVICE PERSONNEL ONLY.

CAUTION: To prevent Plasticiz ers from migrating from the finish o f
the countertop or tabletop or other fur niture, place

NON-PLASTIC

coasters or placemats between the appliance and the finish of the
countertop or tabletop.

Failure to do so may cause the finish to darken, permanent
blemishes may occur or stains can appear.

55

Parts Identification

Pod Holder

(P/N 31001B)

Lever

Water
Diffuser

Base

Pod Chamber

(P/N 31002B)

Drip Spout

(P/N 31003)

Drip Tray

(P/N 31007)

Control Panel

Lid

Water
Tank

(P/N 31005)

Cord

Over Flow Tray

(P/N 31008B)

Your product may vary slightly from illustration.

5-ounce Serving

Power Light/

Indicator Button

8-ounce Serving

FIGURE 1

FIGURE 2

Pod

(Samples included in box.

To order, see page 15.)

Hot Tea Spout

(P/N 31096)

Tea Pod Holder

(P/N 31001G)

Iced Tea Spout

(P/N 31095)

FIGURE 3

6

Before Using Your

One:One

™

Pod Brewing System

Become familiar with all parts of the appliance.

Keep your One:One clean

Clean and descale your One:One™on a regular basis.See “Clean­ing and Descaling”, pages 12-13.We recommend cleaning the
Water Tank and the Drip Spout(s) as well as the Pod Holder(s),
before using your One:One

™

for the first time.Turn on the machine

for a full cycle using water only by follo wing steps 1-7 below.

IMPORTANT: THE MACHINE WILL NOT FILTER COFFEE OR TEA
UNLESS THE PUMP HAS BEEN PRIMED.

1

. Remove the Water Tank by pulling out and then up to remove

from the Base, see Figure 4.

FIGURE 4

7

2. Fill the Water Tank with fresh water up to the ‘Max’ line, and fit
back into the Base (down and in) until it “snaps”into place, see
Figure 5.

3. Lift Lid by pulling out on the Lev er .Top will pop up.Push back so
Lid is in fully raised position, see Figure 6.

4. Place the appropriate spout, coffee, hot or ice tea, inside the
One:One

™

.

FIGURE 6

FIGURE 5

8

5. Make sure the Pod Holder is inside the Pod Chamber. Do not
place a tea or coffee pod in holder. See Figure 7.When brew­ing coffee or tea, use the black pod holder for coffee and the
grey pod holder for tea.

6. To close the Lid, press down firmly on the top of the Lid and
hold in place while pushing the Lev er back so it is flush with the
Lid and locks into place, see Figure 8.

7. Place a cup or mug below the Drip Spout to collect the water.

FIGURE 8

FIGURE 7

9

8. Press the Power Light/Indicator Button to turn power on, then
simultaneously press the 5-Ounce Serving and 8-Ounce Serving
Buttons, see Figure 9.

The water from the Water Tank will cycle through the One:One

™

.

Note: If unit goes unused for 3 or more days, please repeat above

process (steps 1-7).

CAUTION: Do not immerse cord, plug or machine in water or other

liquid.

Brewing Coffee or Tea

CAUTION: Before Brewing in your One:One™for the first time ,

complete the steps listed under “Before Using Your One:One

™

Pod Brewing System” on pages 6-9 to ensure your machine
functions properly.

1. Fill the Water Tank with water up to the ‘MAX’ line. Never pour
other liquids such as milk or hot water into the Water Tank. A
full tank will yield up to 24-ounces of coffee or tea (three mugs).

2. Press the Power Light/Indicator Button.The indicator light will
flash while the water heats up .Heating will take appro ximately
1

1/2 minutes.

3. To open the Lid, place one finger behind Lever and pull out.
Gently raise Lid to open position.

4. Place the appropriate spout, coffee, hot or ice tea, inside the
One:One

™

.

FIGURE 9

10

5. Place the empty Pod Holder inside the Pod Chamber, see
Figure 7.
Note: When brewing coffee or tea, use the black pod holder
for coffee and the grey pod holder for tea.

6. Place one Melitta®javapod™or Cooper’s®teapod™inside the
Pod Holder.Press lightly on the javapod

™

or teapod™to make
sure it sits evenly in the Pod Holder.See Figures 10 and 11
for correct pod insertion.

CAUTION: Use only specially designed Melitta®jav apods™or
Cooper’s

®

teapods™in your One:One™Pod Brewing System.
The use of loose ground coffee , pods or tea bags not designed
for the One:One

™

, may result in poor coffee or tea, and could

possibly damage the machine.
CAUTION: Never use torn javapods or teapods as this could

clog the machine and damage it. Each javapod or
teapod is pre-portioned with the optimal amount of coffee or tea
required per cup.

7. T o close the Lid,press down firmly on the top of the Lid and hold
in place while pushing the Lev er bac k so it is flush with the Lid
and locks into place.

8. Place a mug or cup under the Drip Spout.The cup should hold
at least 7 to 10 ounces, depending on your selection.To make
iced or hot tea, place the appropriate spout inside the
One:One

™

.

9. When the indicator light stops flashing, the appliance is ready
to use. If the indicator light flashes at rapid intervals, see
Troubleshooting on page 14.

FIGURE 10

Bulging end of

pod faces

down

FIGURE 11

correct incorrect

11

10. Select the amount of coffee or tea you wish to brew: either a 5
ounce serving or an 8 ounce serving.When brewing tea, the 8
ounce serving is recommended.The machine will begin the brew­ing process.At the beginning of the brewing cycle, a small amount
of water is dispersed to saturate the pod to ensure full extrac­tion. Following a pause, the machine will brew for about 50 sec­onds for coff ee (or 35 seconds for tea).Y ou can man ually stop the
brewing process at any time b y pressing the Power Button.

CA UTION: Dripping may occur between brewing c yc les.

11.

Dispose of the javapod or teapod after use b y removing the P od
Holder from the Pod Chamber and emptying it. Do not use a
pod more than once.Repeated use may cause the pod to burst
and result in weak and inferior coffee or tea.

Note: Regular r insing of the Pod Holder will optimize the flavor of

the beverage.

You may leave your One:One

™

on if you intend to brew another
cup of coffee or tea.The appliance will turn itself off automatically
after one hour.

Hot Tea and Iced Tea Drip Spout

Assemblies

To maximize the flexibility of your One:One™Pod Brewing System
and to av oid residual flav or when alternating between coff ee or ho t
tea, you may wish to purchase an additional drip spout assembly.
Order on-line at www .1to1coff ee.com or call toll free , 1-800-841-1628.
A shorter spout designed specifically for iced tea is included with
your Brewing System.

FIGURE 12

12

Helpful Hints for Brewing

Fresh Water

For optimal results, use fresh water daily. If you haven’t used your
machine for a few days, follow steps 1-7 in section “Before Using
Your One:One

™

Pod Brewing System” pages 6-9.

Note: If Water Tank becomes dry for 3 or more days , revisit section

“Before Using Your One:One

™

P od Brewing System,” steps 1-7.

Javapodsand T eapods

Remember to remove pods after use. If a pod is left inside the
machine for some time without having used the system, remove it
and see “Before Using Your One:One

™

Pod Brewing System,” page

6, before attempting to bre w coffee or tea.
Use only specially designed Melitta

®

javapods™or Cooper’s

®

teapods™in your One:One™P od Brewing System.The use of loose
ground coffee, pods or tea bags not designed for the One:One

™

,
may result in poor coffee or tea, and could possibly damage the
machine.

Nev er use torn jav apods or teapods as this could clog the machine
and damage it. Each javapod or teapod is pre-portioned with the
optimal amount of coffee or tea required per cup.

Care and Cleaning

CA UTION:Do not immerse cord, plug or machine in water or other liquid.

1. Always unplug the appliance before cleaning.

2. Clean the outer surface of the unit and the W ater Diffuser with a

damp cloth.

3. Remove and disassemble the Pod Holder, Pod Chamber and
Drip Spout.To seperate Pod Chamber
and Drip Spout, remove Drip Spout,
press Lever on the back side of the
Drip Spout, see Figure 13.

Lever

FIGURE 13

13

4. Remove the Drip Tray and Overflow Tray, see Figure 14.

5. Clean the Water Tank, Pod Holder, Pod Chamber, Drip Spout,

Drip Tray and Ov erflo w Tray with hot water. If necessary, use a
little dish soap.
Note:The PodHolder, the Drip Tray, Overflow Tray and the Drip
Spout may be washed in the dishwasher (top shelf only).The
top part of the tank can be removed for thorough cleaning.Do not
place the Water Tank in the dishwasher.

6. Rinse all parts with fresh water after cleaning.
Note: Do not try to dry the inside of the Removable W ater Tank

with a cloth because this will leave a residue of lint and may
clog your Coffeemaker.

Descaling

Regular descaling will extend the service life of your machine and
ensure optimal results over time.

1. Follow the instructions given in “Before Using Your One:One

™

Pod Brewing System,” pages 6-9, replacing one fourth of the
water with white vinegar.

2. Brew 3, 8 oz. cups using empty Pod Holder (follow the Brew-
ing Instructions on page 9.)

3. Remove W ater Tank, Pod Holder , P od Chamber and Drip Spout
and wash thoroughly.

4. Repeat instructions in step 2 up to four times in order to flush
vinegar residue. Empty Water Tank and refill with fresh water
after each cycle.
Note:You may also use a cleaner designed f or automatic drip
coffee mak ers.Simply follow the instructions as stated on the
package.

FIGURE 14

14

Troubleshooting

Should a problem occur, you may be able to find an answer in the
text below. If the text proves unhelpful or if you require further
information, please contact Consumer Service.

1. The coffee or tea is too weak.

Check the following:

• the pod is placed properly in the Pod Holder.You may need

to lightly press it down into the holder.

• you have selected the correct b utton according to the number

of ounces and strength desired.Use one javapod f or either one
5-ounce, bold European serving, or an 8-ounce serving of
American style coffee.When brewing tea be sure to select the
8-ounce serving.

• you are using a fresh Melitta

®

javapod™or Cooper’ s®teapod™.

2. The coffee is too strong.

Check that you have selected the correct button. Use the
8-ounce button f or less robust coffee .

3. There is less water than normal volume of water during
brew cycle brewing from the appliance into the cups.

Descale appliance.See “Descaling,” page 13.

4. Water drips from the appliance.
Note:Some water may drip between cycles,this is normal.

Check the following:

• the Pod Holder must be placed properly within the P od Cham-

ber and the Lever locked into position.

• the Water Tank must not be filled above the ‘MAX’ line.

• the Pod Holder may be clogged. Rinse under tap water to

unclog the screen.If necessary , y ou may also use a scrubbing
brush or a pin.

• the pod must be properly placed so it sits evenly into the

holder. Lightly tap it down into the holder. See Figure 10.

• some water droplets on your countertop are normal and may

be caused by the filling and replacing of the Water Tank.

FIGURE 15

correct incorrect

15

5. The indicator light is flashing.

A flashing indicator light means the machine is heating.This
normally lasts for 1

1/2-2 minutes. If indicator light is flashing

rapidly (more than a second apart), see #6 below.
If the indicator light flashes continually for more than 4 min utes,

contact Consumer Service.

6. The indicator light keeps flashing at rapid intervals.

Check the following:

• the W ater Tank must be inserted properly inside the appliance.

• there must be enough water in the W ater Tank. Fill the Water

Tank to the “Max” fill line.

• the appliance may require cleaning. See “Before Using Your

One:One

™

Pod Brewing System”, pages 6-9.

• room temperature must be above 40°F.

7. The Lid will not open.

Turn appliance off.Unplug appliance.Wait f or appliance to cool
completely (about 30 minutes) and try opening Lid again.Clean
all removable parts (Dr ip Spout, Pod Holder, Pod Chamber) as
described on pages 12-13.

For any other problem please contact Consumer Service,
1-800-841-1628 or email us at [e-mail].

To Order Melitta®Javapods™or

Cooper’s

®

Teapods

™

It’s easy to order pods. Just log onto our dedicated website,
www.1to1coffee .com, and order online.

To order by phone, call toll-free, 1-800-841-1628.
To ensure a steady supply of fresh javapods and teapods and to take

advantage of special promotions, join our One:One

™

Continuity Club

(see registration materials included with this product).
Melitta

®

javapods™and Cooper’ s®teapods™are also av ailable at many

retail outlets that carry the Melitta

®

One:One™Pod Brewing System

or Melitta

®

One:One™Javapod Coffeemakers.

16

IMPORTANT NOTICE

If any parts are missing or defective,

DO NOT return this product.

Please call our Customer Service Department for assistance.

800-841-1628

Monday - Friday 9:00 am - 5:00 pm CST

Thank You

LIMITED ONE YEAR WARRANTY
Warranty: This Melitta®product is warranted by Salton, Inc.to be free from

defects in materials or workmanship for a period of (1) year from the original
purchase date.This product warranty co vers only the original consumer pur­chaser of the product.

Warranty Co verage:This warranty is void if the product has been damaged by
accident in shipment, unreasonable use, misuse, neglect, improper service,
commercial use, repairs by unauthorized personnel, normal wear and tear,
improper assembly, installation or maintenance abuse or other causes not aris­ing out of defects in materials or workmanship.This warranty is effective only if
the product is purchased and operated in the USA, and does not extend to
any unit which has been used in violation of written instructions furnished with
the product, or to units which have been altered or modified, or to damage to
products or parts thereof which have had the serial number removed, altered,
defaced or rendered illegible.

Implied Warranties: ANY IMPLIED WARRANTIES WHICH THE PUR­CHASER MAY H AVE ARE LIMITED IN DURATION TO ONE (1) YEAR FROM
THE DATE OF PURCHASE.Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to you.

Warranty P erf ormance: During the above one-year warranty period, a prod­uct with a defect will be either repaired or replaced with a reconditioned com­parable model (at our option) when the product is returned to the Repair Center ,
or the purchase price refunded.The repaired or replacement product will be in
warranty f or the balance of the one-year warranty period and an additional one­month period. No charge will be made for such repair or replacement.

Service and Repair: Should the appliance malfunction, you should first call
toll-free 1-800-841-1628 between the hours of 9:00 am and 5:00 pm Central
Standard Time and ask f or CONSUMER SER VICE stating that y ou are a con­sumer with a problem. Please refer to model number

MES2B, MES2R, MES2W,

MES2K, MES2MG, MES2BCAN, MES2RCAN, MES2WCAN, MES2KCAN or MES2MGCAN

when you call.
In-Warranty Service (USA): For an appliance covered under the warranty

period, no charge is made for service or postage.Call for return authorization
1-800-841-1628.

Out-of-Warranty Service:A flat rate charge by model is made for out-of-war­ranty service. Include $12.00 (U.S.) for return shipping and handling.We will
notify you by mail of the amount of the charge for service and require you to
pay in advance for the repair or replacement.

For products purchased in the USA,but used in Canada:You may return
the product insured, packaged with sufficient protection, and postage and
insurance prepaid to the USA address listed below. Please note that all cus­toms duty / brokerage f ees, if any, must be paid by you and we will require you
to pay the cost of customs duty / broker age fees to us in advance of our per­forming any service.

Risk During Shipment: We cannot assume responsibility for loss or dam­age dur ing incoming shipment. For your protection, carefully package the
product for shipment and insure it with the carrier .Be sure to enclose the fol­lowing items with your appliance: any accessories related to your problem,
your full return address and daytime phone number, a note descr ibing the
problem you experienced, a copy of your sales receipt or other proof of pur­chase to determine warranty status.C.O.D.shipments cannot be accepted.

To return appliance, ship to: To contact us, please write to, call or email:

Attn: Repair Center Salton, Inc.
Salton, Inc. P.O.Box 6916
708 South Missouri Street Columbia, MO 65205-6916
Macon, MO 63552 1-800-841-1628

Email: [e-mail]

Limitation of Remedies: No representative or person is authorized to
assume for Salton, Inc. any other liability in connection with the sale of our
products.There shall be no claims for defects or failure of performance or
product failure under any theory of tort, contract or commercial law including,
but not limited to negligence, gross negligence, strict liability, breach of war­ranty and breach of contract.Repair, replacement or refund shall be the sole
remedy of the purchaser under this warranty, and in no event shall Salton, Inc.
be liable for any incidental or consequential damages, losses or expenses.
Some states do not allow the exclusion or limitation of incidental or conse­quential damages, so the abov e limitation or e xclusion may not apply to you.

Legal Rights:This warranty giv es you specific legal rights, and you ma y also
have other rights which vary from state to state.

For more information on Salton products:
Visit our website: www.eSalton.com

© 2004 Salton, Inc. P/N 61468
All Rights Reserved Printed in China