Thank you
T
U
for choosing Meliconi.
This simplifi ed universal remote control contains all the main functions of most
Insert the batteries and program your remote control before using it.
USING THE KEYS AND FUNCTIONS
Control the
volume using +.
Control the
volume using -.
To select an
external terminal.
Mute key.
Read these instructions carefully before programming your remote control!
To use the remote control with your appliances, you must fi rst program Speedy Goal Plus as described below.
You can also visit our Internet site www.meliconi.com to have access to interactive instructions for easier and faster
1. Make sure that the TV is ON.
IF YOU DO NOT HAVE THE PROGRAMME SELECTION KEYS ON YOUR
2. Hold down the and
ORIGINAL REMOTE CONTROL
keys simultaneously until the light indicator at the top starts to fl ash
indicating that the remote control is in programming mode.
If your remote control does not have the programme selection keys
3. Press key four times then point the remote control at the appliance.
(e.g. / , +/-, CH+/-..etc) once you have programmed
Press and release the key slowly several times.
Speedy Goal Plus, you can still select the programmes from 0 to 9, as
STOP when your TV goes OFF.
follows:
4. When your TV is OFF, press the and keys simultaneously. When
• Hold down the and keys simultaneously until the light
you release the keys, three fl ashes indicate that the search operation
indicator starts to fl ash indicating that the remote control is
has been completed correctly.
in programming mode.
• Release the keys and press 9 times within 12
Additional check
seconds.
Check that all 7 keys are operating correctly.
If the commands work incorrectly or erratically,
been completed correctly.
you have probably entered a code for a similar
• Make sure you can change programmes
but different remote control.
from 0 to 9 using the and keys.
In this case, repeat the search
If not, repeat the search operation,
procedure from point 2 until
starting from point 2.
TV remote controls on the market.
Keep your Instructions Booklet for future reference.
FITTING THE BATTERIES
To select the next
programme or to turn
ON your TV.
Press them together
to turn ON your TV
on programme 1.
To select the previous
programme or
to turn ON your TV.
ON/OFF to turn OFF
your TV and,
in some cases,
to turn ON your TV.
The remote control
requires 2 new AAA/LR03
alkaline batteries.
Insert the batteries
as shown:
• Batteries must be changed once a year.
• Change the batteries if the light indicator starts to fl ash during use. The
batteries are low.
• When removing batteries, insert the new ones within 5 minutes or you may
have to reprogram your remote control.
• Make a note of the code for your TV on the adhesive label supplied inside
the battery compartment cover. This note will be handy if you have to
reprogram your remote control.
SET-UP
remote control programming.
PROGRAMMING YOUR REMOTE CONTROL
all keys respond correctly to
the commands sent.
Three fl ashes
indicate that the operation has
Identify and take note of the TV code which you have searched for,
NOTE: DURING THE SEARCH OPERATION, THE LIGHT INDICATOR FLASHES MORE QUICKLY. THE LIGHT INDICATOR
• if no keys are pressed for 12 seconds • if you press keys other than those indicated
• if the code search list is completed. In this case, visit www.meliconi.com
STOPS FLASHING AND YOUR REMOTE CONTROL LEAVES PROGRAMMING MODE IN THE FOLLOWING CASES:
PROGRAMMED CODE NOTING
When you have programmed Speedy Goal Plus
Meliconi, note down the code on the label
in the battery compartment cover.
To fi nd the code for your remote control:
1. Hold down the and keys simultaneously
until the light indicator at the top starts to fl ash
indicating that the remote control is searching for
the code.
2. Release the keys and, within 12 seconds,
press and simultaneously.
3. Release and and pay attention to the
fl ashing of the LED: a long fl ash corresponds to a +
while a short fl ash corresponds to a - .
Note the sequence of the
down on the label in the battery compartment cover,
from left to right.
9 fl ashes
and note them
USING YOUR REMOTE CONTROL
Once you have programmed Speedy Goal Plus, you can turn ON your
TV in three ways:
• Press or .
• Press .
• Press and simultaneously: this sends the code for programme 1.
To return to programme 1 directly, press and simultaneously.
INFO LINE
• read this booklet carefully – this will help you to solve
• consult our Internet site www.meliconi.com to
If you have any queries about Speedy Goal Plus:
answer all your queries more easily and quickly.
The warranty ceases to be valid if the product
is tampered with or used incorrectly.
Remote control model Speedy Goal Plus
Purchase date___________________
following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
RE-PROGRAMMING YOUR REMOTE CONTROL BY
ENTERING THE CODE NOTED DOWN
If the remote control is no longer programmed because it has
been left without batteries for a long time or has fl at batteries, you
can re-program it quickly as follows:
1. Hold down the and keys simultaneously until the light
indicator at the top starts to fl ash indicating that the remote control is
programming.
2. Release the keys and, within 12 seconds, using the
and keys, enter the nine-sign code which you noted down
before. At the end,
correctly. If not, try the code entry procedure again from point 1.
three fl ashes
TROUBLESHOOTING
PROBLEM
1.
The TV does not
respond and the
light indicator does
not light up when
you press a key.
2.
The TV does not
respond but the
light indicator does
light up.
3.
The TV does
not respond and
the light indicator
fl ashes.
4.
Not all remote
almost all problems
WARRANTY: 2 years
control commands
are working
correcting.
5.
The and
keys do not select
the programmes.
Agent’s stamp
indicate that the code has been saved
SOLUTION
1. Check that the
batteries are fi tted
correctly. If necessary, replace them
with 2 new 1.5 V
AAA/LR03 alkaline
batteries.
2. Check that the
batteries are new
and that the remote
control is pointing
at the appliance
without any obstacles in the way.
If required, reset
the remote control
code by repeating
the programming
procedure.
3. Batteries are low.
Replace them.
4. You may have
used the wrong
code. Reset the
remote control
code, following
the programming
procedure.
5. The original
remote control may
not have had this
function. In this
case, set the code
(press 9 times)
as described in the
PROGRAMMING
YOUR REMOTE
CONTROL section
above.
Loading...