Page 1
Keep this booklet for future reference.
IMPORTANT: The remote control must not be exposed to excessive heat sources.
Before using the remote control, insert the batteries and programme it.
INSERTING THE BATTERIES
EN
I
COMBO
Thank you for choosing a Meliconi remote control.
The Speedy 210 combo remote control can control a TV (analogue or digital) and can also simultaneously control a
decoder if one is connected to it (terrestrial or satellite).
Thanks to its combined keypad, there is no need to manually select the device to be controlled. Using Speedy 210
combo to control both devices (TV + DECODER), the light blue buttons automatically control the TV, and the dark
blue buttons control the DECODER, but it is also possible, with suitable settings, to make all of the buttons control a
single device.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
Its ergonomic shape and soft rubber body make it easy to grip and protect the remote control if it is knocked and
dropped.
USE OF THE BUTTONS AND FUNCTIONS
The functions of the buttons described below are available only if they are on your original device.
Selects the next programme.
Indicator light.
Menu options confirm button
TV ON button, sometimes needed to switch on the TV.
Turns up the TV volume.
Turns down the TV volume.
Numeric keypad.
Selects digital TV and radio
Button for exiting Teletext and
returning to normal screen.
OFF for switching off the decoder (STB).
For selecting an external input sourcefor the TV.
ON/OFF switches the TV OFF and in some cases ON.
Menu options exit button
Selects the previous programme.
The remote control requires 2 new 1.5V alkaline AAA/LR03 batteries.
Insert them as illustrated.
Try pressing a number button and check that the red light remains lit continuously
until you release the button. If the light fl ashes, the batteries inserted are not charged
and are about to go fl at, therefore you must substitute them.
Teletext button.
7
Page 2
Do not leave fl at batteries inserted, as liquid may leak and damage the remote control
The Speedy 210 combo remote control is a universal remote, so its memory contains data relating to numerous
SETTING THE CODE
SETTING CODES USING INTERNET
SETTING CODES USING A MOBILE PHONE
devices of various brands available on the market.
Each original device has a specifi c code which must be used to set up the remote control.
Therefore, to use Speedy 210 combo you must enter the specifi c code for each device you want to control.
Use one of the following methods to identify the correct code and set it in your remote control:
A) - INTERNET (recommended)
B) - MOBILE PHONE (SMS)
C) - MANUAL SEARCH
If you have an Internet connection available, follow the on-line guide on the www.meliconi.com/guida website to
identify the specifi c codes for the devices you want to control. Then set the codes manually in your MELICONI remote
control as described in the ENTERING THE CODE DIRECTLY procedure.
(the service is fee, the only cost being that of sending the SMS, which depends on your service operator tariffs)
From today, MELICONI gives customers who don’t have internet access the chance to receive the codes for
programming their remote control directly on their mobile phone.
Send an SMS as follows: 2C, Type, Brand, Model
Fixed text which must always be included
Indicate the type of device to be controlled using only one of the following
abbreviations: TV
SAT (satellite decoder)
TER (terrestrial decoder)
indicate the brand of the device to be controlled
indicate the model of the device to be controlled, usually shown on a label
on the back of the device (if you don’t know the model, don’t write anything
after the brand)
EXAMPLE:
2C, TV, PHILIPS, 32PFL3614
8
2C, TV, PHILIPS,
32PFL3614
Page 3
MANUAL CODE SEARCH
IMPORTANT - separate the information with a comma, and be as precise as possible so that the IT system can
Check that the other buttons (light blue) correspond to the functions of the original remote control; if not, it is
likely that the code found is incorrect, but is used for a very similar device, therefore repeat the procedure
from point 2
C1. MANUAL SEARCH (TV)
NOTE: If you don’t receive an SMS on your mobile phone or if the message says ERROR / NO CODE, it means the system
was not able to process the data you sent. Do not try sending another SMS, instead set the code using the MANUAL
CODE SEARCH procedure
.
search the data and respond correctly.
Send the SMS to the number 0039 345 7518893 and wait for an SMS reply.
Once you have received the SMS with the list of codes, set the fi rst code in the remote control as described in the
ENTERING THE CODE DIRECTLY section.
Place the MELICONI remote control in front of the device, which should already be ON, and press the TV or ON/OFF
STB button (depending on the device being operated). If the device does NOT switch off, try setting the next code in
the SMS list on the remote control. When the device reacts, check whether the other buttons are operating correctly
too. If they do, the remote control is ready to use. If they don’t, you are probably using an incorrect code intended
for a very similar device. At this point, ignore the SMS list and consult the MANUAL CODE SEARCH section to fi nd a
more suitable code.
(only to be performed if the specifi c code could not be found)
If you want to use the Speedy 210 combo to simultaneously control two different devices (TV + DECODER) follow
procedure C1 then procedure C2.
To control a single device (DECODER), follow only procedure C2.
To control a single device (DIGITAL/ANALOGUE TV), follow procedure C3.
If the manual search for the code is successful, obtain the code in use by following the DISPLAY CODE IN USE
procedure and make a note of it inside the battery cover.
1. Switch on the TV and select a programme
2. Simultaneously hold down the VOL + and VOL - buttons.
3. When the indicator light starts fl ashing, release the buttons
TV
and briefl y press the ON/OFF TV button.
4. The indicator light fl ashes faster; the remote control is ready
for the search.
5. Point the remote control at the TV. Slowly press and release
the ON/OFF TV button several times, stopping when the TV
is switched off (you may need to press the button several
dozen times).
6. When the device has switched off press the OK button.
Three long fl ashes indicate that the operation was completed
OK
correctly.
TV
9
Page 4
C2. MANUAL SEARCH (DECODER)
Check that the other buttons (dark blue) correspond to the functions of the original remote control; if not,it is
likely that the code found is incorrect, but is used for a very similar device, therefore repeat the procedure
from point 2.
1. Switch on the device and select a programme.
C3. MANUAL SEARCH (DIGITAL/ANALOGUE TV)
2. Simultaneously hold down the P+ and P- buttons.
3. When the indicator light starts fl ashing, release the
buttons and briefl y press the ON/OFF STB button.
4. The indicator light fl ashes faster; the remote control is
ready for the search.
5. Point the remote control at the device. Slowly press and
release the ON/OFF STB button several times, stopping
when the decoder is switched off (you may need to press
the button several dozen times).
6. When the device has switched off press the OK button.
Three long fl ashes indicate that the operation was
completed correctly.
1. Switch on the TV and select a programme.
2. Simultaneously hold down the VOL + and P+ buttons.
3. When the indicator light starts fl ashing, release the
buttons and briefl y press the ON/OFF TV button.
4. The indicator light fl ashes faster; the remote control is
ready for the search.
5. Point the remote control at the TV. Slowly press and
release the ON/OFF TV button several times, stopping
when the TV is switched off (you may need to press the
button several dozen times).
6. When the TV has switched off press the OK button. Three
long fl ashes indicate that the operation was completed
correctly.
STB
STB
STB
OK
TV
TV
OK
10
Page 5
Check that the other buttons correspond to the functions of the original remote control; if not, it is likely that the code
found is incorrect, but is used for a very similar device, therefore repeat the procedure from point 2.
NOTE: During the search the indicator stops fl ashing and the remote control exits the programming mode in
the following cases:
• if for 12 seconds the button indicated is not pressed or if another button is pressed
• if the list of codes to fi nd is terminated. If this happens, go to the www.meliconi.com website
Three long fl ashes indicate a correct setting. If they do not appear, repeat the procedure.
ENTERING THE CODE DIRECTLY
Make a note of the code obtained on the label on the inside of the battery cover. You may need it in future.
(only to be performed if you know the specifi c code to be set)
To go to the programming mode, according to requirements, use one of the following pairs of buttons:
VOL + and VOL - to set the code for the TV part only - (light blue buttons)
P + and P - to set the code for the DECODER part only - (dark blue buttons)
VOL + and P + to set a single code and control only one device - (whole keypad)
1. Switch to the programming mode by simultaneously
holding down the appropriate pair of buttons.
Example of TV code
2. When the indicator light starts fl ashing, release the
buttons and immediately enter the specifi c code
previously found.(e.g.: 1306)
DISPLAY CODE IN USE
If you set up the remote control using the MANUAL SEARCH procedure, obtain and make a note of the code in use
as follows:
1. Simultaneously hold down the VOL+ and VOL- buttons (if
you want to fi nd the codes of analogue or digital TVs), or
P+ and P- (to fi nd the decoder code).
2. When the indicator light starts fl ashing, release the
buttons and briefl y press the TV/RADIO button.
3. After a pause of several seconds, the indicator light
produces four sets of fl ashes, spaced out, corresponding
to the code to be obtained. Count the number of fl ashes.
Each set of fl ashes corresponds to one fi gure in the code.
Ten fl ashes correspond to the fi gure 0. For example, for
the code 1306 the following fl ashes will be obtained:
TV Code Decoder Code
Code obtained = 1306
11
Page 6
PROBLEM
TROUBLESHOOTING
INFO-LINE
The device does not respond and the indicator light
does not come on when a button is pressed
SOLUTION
Make sure that the batteries are inserted correctly,
or substitute them with 2 new 1.5V alkaline AAA/
LR03 batteries.
The device does not respond but the indicator light
comes on.
Make sure that the batteries are new and that the
remote control is pointing at the device without any
obstacles between them.
If necessary, enter the remote control code again by
repeating the programming procedure.
When you press a button the indicator light fl ashes
Substitute the batteries, which are about to go fl at.
and the device does not respond to commands.
The remote control does not execute all commands
correctly.
You may be using the wrong code.
Enter the remote control settings again by repeating
the programming procedure.
If you have any questions about the new Speedy 210 combo remote control:
• carefully read this Instructions Booklet which will allow you to solve most problems
• consult our website www.meliconi.com where you will fi nd the answers you need in the fastest, easiest way.
2 year WARRANTY
The warranty is voided if the product is tampered with or used improperly.
Retailer stamp
Remote control model Speedy 210 combo
Purchase date
The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the end of its useful life the product must
be collected separately from other waste. Therefore, at the end of the device’s life, you must take it to appropriate centres for the differentiated
collection of electrical and electronic waste, or return it to the retailer when purchasing a new device of equivalent type, on a one-for-one basis. Suitable
differentiated collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible treatment and disposal, help
to prevent any negative effects on the environment and health and to promote the recycling of the materials of which the device is made. Improper
disposal of the product by the user will be subject to the sanctions in Legislative Decree No. 22/1997 (article 50 and subsequent articles of Legislative
Decree No. 22/1997).
12
Loading...