Page 1
GB
Thank you for choosing MELICONI.
This universal remote control has the essential functions for the simplified use of an analogue or a digital
television combined with a satellite or terrestrial decoder - without having to switch between one appliance and
another. The dark blue buttons transmit the commands to the decoder while the light blue buttons control the
functions that correspond to the TV. If used with a digital TV, all the buttons control the same appliance.
Keep your Instructions Booklet for future reference.
BUTTON AND FUNCTION USE
To select the next programme.
Indicator light.
Interrupts and restores the TV audio.
To reduce the TV's audio volume.
Numeric keypad.
Button to exit the Teletext
and return to normal viewing.
TV ON button which is occasionally
needed to turn the TV on
To increase the TV's audio volume.
To select the previous programme.
To select an external input
terminal to the TV.
Button to access the Teletext.
OFF to turn the decoder off (STB).
ON/OFF to turn OFF the TV
and in some cases to turn it ON.
FITTING THE BATTERIES
Before programming and using the remote control, fit the batteries.
The remote control requires 2 new 1.5 V AAA/LR03 alkaline batteries. Insert the batteries as shown:
• The batteries must be changed once a year.
• Replace the batteries if the indicator light on the remote control starts to
flash during use. The batteries are low.
• This remote control has a permanent memory and does not lose the
programmed codes when the batteries are removed.
• Make a note of the code for your appliances on the adhesive label found
inside the battery cover. This note will be handy if you have to reprogram
your remote control.
Warning: do not expose the remote control to sources of excessive heat
17
Page 2
PREPARE FOR USE
Read these instructions carefully before programming your remote control!
To command your appliances, you must programme your Speedy 2 COMBO as described in the next
paragraph. For those who can connect to the internet website www.meliconi.com, you will find interactive
instructions for a faster and easier programming of your remote control.
HOW TO PROGRAMME THE REMOTE CONTROL
If you have an analogue TV and an external decoder, follow procedure A and then procedure B. Follow procedure
C if you have a digital TV.
ANALOGUE TV PROGRAMMING
- - Turn on the TV and select a programme.
- Simultaneously hold down the
indicating that the remote control is in the programming state.
- Release the buttons and enter the code 0001 within 12 seconds. The indicator light begins flashing more
quickly, indicating that the remote control is ready for the search.
- Point the remote control towards the TV. Press and slowly release the
the appliance goes off (you may need to press the button a few dozen times).
- When the appliance goes off, press the
operation has been completed successfully.
- Turn on the appliance and select a programme.
- Simultaneously hold down the
indicating that the remote control is in the programming state.
- Release the buttons and enter the code 0001 within 12 seconds. The indicator light begins flashing more
quickly, indicating that the remote control is ready for the search.
- Point the remote control towards the appliance. Press and slowly release the
stopping when the appliance goes off (you may need to press the
- When the appliance goes off, press the button to confirm. Three long flashes indicate that the
operation has been completed successfully.
- Turn on the TV and select a programme.
- Turn on the TV and select a programme
starts to flash indicating that the remote control is in the programming state.
- buttons for 5 seconds until the upper indicator light starts to flash indicating that the remote control is in the
programming state.
- Point the remote control towards the appliance. Press and slowly release the button several times,
stopping when the appliance goes off (you may need to press the button a few dozen times).
- When the appliance goes off, press the button to confirm. Three long flashes indicate that the
operation has been completed successfully.
Additional check
Check that some of the other buttons, corresponding to those on your original remote control, work correctly.
If the commands function incorrectly or erratically, you have probably entered a code for a similar but different
remote control. In this case, repeat the search procedure starting from point 3.
and buttons for 5 seconds until the upper indicator light starts to flash
button several times, stopping when
button to confirm. Three long flashes indicate that the
DECODER PROGRAMMING
and buttons for 5 seconds until the upper indicator light starts to flash
button a few dozen times).
button several times,
DIGITAL TV PROGRAMMING
and buttons for 5 seconds until the upper indicator light
18
Page 3
RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN
Identify and take note of the code which you have discovered
NOTE: The indicator light flashes more quickly during the search operation.
The indicator light stops flashing and the remote control exits the programming mode in the following
cases:
• if no buttons are pressed for 12 seconds
• if the end of the code search list has been reached. In this case, consult the website
www.meliconi.com.
following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
PROGRAMMED CODE NOTING
Remember to always make a note of the 4-digit codes for your appliances on the inside of the battery cover
when the code search and saving are finished. The codes will be required if the remote control needs to be
re-programmed following accidental deletion.
To find the code for your remote control:
1. Simultaneously hold down the and buttons for 5 seconds (if you want to know the codes for the
analogue or digital TV), or
light starts to flash indicating that the remote control is in the programming state.
2. Release the buttons and press and release the
3. After a short pause, the indicator light produces four series of flashes with a space between them,
corresponding to the code you are looking for. Count the number of flashes; each series of flashes
corresponds to one figure in the code. 10 flashes correspond to 0. For example, the code 1306 corresponds
to:
= 1
= 3
= 0
= 6
4. Make a note of the code on the adhesive label inside the battery cover for quick and easy consultation.
1. Simultaneously press and hold for 5 seconds the buttons corresponding to the appliance for which you
would like to enter the code:
for the digital TV, until the indicator light starts to flash indicating that the remote control is in the
programming state.
2. Upon release insert the code number you noted beforehand. Three flashes indicate that the code has been
memorized correctly. If not, try the code entry procedure again starting from point 1.
and (if you want to know the code for the decoder), until the indicator
button within 8 seconds.
and for the analogue TV, and for the decoder, or and
19
Page 4
TROUBLESHOOTING
PROBLEM
The appliance does not respond and the
indicator light does not light up when a
button is pressed
.
The appliance does not respond but the
indicator light lights up
.
The appliance does not respond to the
commands and the indicator light flashes
when a button is pressed
.
The remote control is not carrying out all the
commands properly
.
SOLUTION
Check that the batteries are fitted correctly.
If necessary, replace them with 2 new 1.5 V
AAA/LR03 alkaline batteries..
Check that the batteries are new and that the
remote control is pointing at the appliance
without any obstacles in the way. If necessary,
reset the remote control code, repeating the
programming procedure.
The batteries are low. Change them.
Perhaps you are using an incorrect code.
Reset the remote control by repeating the
programming procedure.
INFO LINE
If you have any queries about your new Speedy 2 COMBO remote control::
• read this Instruction Booklet carefully, which will help you find a solution to most of your problems
• consult our website www.meliconi.com where you can quickly and easily find the answers you need.
2-year WARRANTY
The warranty ceases to be valid if the product
is tampered with or used incorrectly.
Remote control model Speedy 2 COMBO
Purchase date
20
Dealer's stamp
Loading...