Mega MJ-1016A User Manual

MEGA BEAM230 MOVING HEAD LIGHT

MJ-1016A

User manual

Thank you for choosing our beam moving head light. For the sake of your safety, Please read and follow these instructions carefully and keep this manual in a safe place for future reference.

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

2

Catalogue

Chapter Page

Safe Usage Of The Product ------------------------------------------------------------------------------------------3 Install The Equipment -------------------------------------------------------------------------------------------------4 Fitting The Lamp--------------------------------------------------------------------------------------------------------4 Power Code Connection ----------------------------------------------------------------------------------------------6 DMX Connection -------------------------------------------------------------------------------------------------------5 DMX Terminator --------------------------------------------------------------------------------------------------------6 Function Set ---------------------------------------------------------------------------------------------------------------6 Operation Menu ----------------------------------------------------------------------------------------------------------7 Maintenance --------------------------------------------------------------------------------------------------------------10 Keeping The Product Clean ------------------------------------------------------------------------------------------11 Trouble Shooting---------------------------------------------------------------------------------------------------------11 Equipment and Appendix----------------------------------------------------------------------------------------------11 Channel List---------------------------------------------------------------------------------------------------------------12 Technical Parameters---------------------------------------------------------------------------------------------------14

☆Important notice:

· In this instruction for use contains about the installment and the use aspect important information of the beam moving

head. When installing and using, you need to look this usage instruction strictly.

· Before open the beam moving head and if you want to do the repair work, please make sure the power source is at the separation condition.

· Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and the unit are in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer or dealer.

Attention: Unceasingly carries on the product improvement about our company the policy, in this instruction booklet

carries the data will have the possibility to be able to change in the future, when no longer separate notice change matters concerned. Our company retains when the product improvement changes the related specification the authority. This instruction booklet publisher cannot be responsible regarding this instruction booklet in information accuracy, also cannot the related consequence which causes regarding these information be responsible.

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

3

SAFE USAGE OF THE PRODUCT

When unpacking and before disposing of the carton, check there is no transportation damage before using the product. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The product is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids. The product is not designed or intended to be mounted directly on to inflammable surfaces The product is only intended for installation, operation and maintenance by professional person. The product must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure that no ventilation slots are blocked. Do not product the beam onto inflammable surfaces, minimum distance is 12m. Avoid direct exposure to the light from the lamp. The light is harmful to the eye. Do not attempt to dismantle or modify the projector in any way. Electrical connection must only be carried out by qualified personnel. Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector. It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards. Do not connect this device to any other types of dimmer apparatus. Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Keep the light clean. Do not touch the light glasss with bare hands. The product should always be installed with a secondary safety fixing. On the projector base brink,

there is a hole for the safety cord provided. It should be attached as shown in “installing the projector”

section. The lamp used in this projector is a discharge lamp. After switching off don,t attempt to restart the projector until lamp has cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector. But occasional breaks will prolong the life of the lamp and projector. Never run the projector without a lamp. The light shall be changed if it has become damaged or thermally deformed or reached its life limit. Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired, for example by cracks or deep scratches.

Exterior surface temperatures of the luminaire after 5 minutes operation is 70°。，when steady state is achieved 140°。 There is no user serviceable parts inside the projector, do not open the housing and never operate the product

with the covers removed.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

★Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

4

Install The Equipment:

Use 2pcs clamp and 1safety cord(need to purchase).Use clamp fix with light hook which in the packing box with light, then use screw install to the bottom of lamp. Hang the fixture on the structure and fasten the screws attached to each clamp. Make sure the light is installed reliable, and confirm the light which you fixed is strong enough for hanging the light. Base on safety reason, please according to the above picture using safety wire cross the light to make it strong enough again.

Warning!

1. Unlock the PAN and TILT before the 1st application of the light for safety. 2．Hook and clamp only use for hanging the light. Do not use clamp as a tool to move fixtures. 3．Base on safety reason, please use the safety cord which can afford the weight ten times of lamp through Insurance hole for auxiliary hanging. 4．Don't use the handle of the moving head light to fixed or lift!

Fitting The Lamp：

.Loosen 4 fast-fit screws and remove the back cover, when fitting/replacing the lamp. .Do not touch the bulb of the new lamp with bare hand so as not to influence the beam output. .Do not harm the sticking out point of the lamp during its installation. .Fit new lamp and close the back cover by fastening 4 fast-fit screws when finished lamp installation. .Lamp work will reach a very high temperature, Vapor discharge lamp can not continue to supply this physical characteristics, therefore, the power completely cool for 10 minutes before on the operation. Failure to do so will lead to a high-pressure discharge and short circuit burned out the computer's control panel components.

Notes: Unplug the light from power before lamp installation or replacement and wait for it to cool.

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

5

Power Code Connection:

Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off.

★It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards.

DMX Connection:

Connection between the controller and a projector and between one projector and another must be made with a 2 core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via cannon 3 pin (which are included with the projector) XLR plugs and sockets. The XLR's are connected as shown in the figure above. Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not connected in any way. The XLED 590 accepts digital control signals in protocol DMX512 (1990). Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second

fixture’s input and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX

terminator as shown in the figure below.

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

6

DMX Terminator:

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

Function Set:

1. Touch Operation

Up

Ok

Down

Back

Set Up

Manual

System

Advanced

180

中／ＥＮ

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

7

2.Button Opertion

UP

Back Back

DOWN

Use button switch and LCD display, can set the address code and function code easily. Check or modify lighting function settings, Press the Set UP or OK button. LCD display panel will display main menus. Function operation menu all have corresponding submenu . Each menu all represent the specific functions of lamps, specific see below "operation menu" section. Set or browse function setting of lamp, Press UP or DOWN key. Press OK key to save your changes or to enter submenu, Press UP or DOWN can change value(Plus or reduce number).

Operation Menu:

 Menu Structure chart

Main Menu Sub Menu

OK

Invert Pan

Set Up

Run Mode

Channel Mode

Invert Tilt

DMX Address

DMX

AUTO 1-4

0-512

16/20

ON/OFF

DrawUP 8

Forward 0

F-stand 8

F-Sleep 8

Random

Sound

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

8

Pan-Tilt Swap

Pan-Tilt Encoder

No DMX Signal

Display Power Save

ON/OFF

KEEP/CLEAP

ON/OFF

Lamp On @ Startup

Linear Color

ON/OFF

Load Default

Ok/Cancel

Manual

Colour Wheel

0-255

Stop/Strobe

0-255

Dimmer

0-255

Gobo Change

0-255

Prism Insertion

0-255

Prism Rotation

0-255

Frost

0-255

Gobo Shak

0-255

Focus

0-255

Pan

0-255

Pan Fine

0-255

Tilt

0-255

Tilt Fine

0-255

Pan-Tilt Speed

0-255

Rest

Ok/Cancel

Lamp Control

ON/OFF

Software Version

System

Total Fixture Hours

YJ-A102

******

Partial Fixture Hours

Total Lamp Hours

******

Partial Lamp Hours

******

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

9

 Sub menu include Set Up, System, Manual,Advanced Model  Set Up

Press “Set UP” , and choose Man control by “UP&DOWN”，it will be show Run Mode, DMX Address, Channel Mode, Invert Pan, Invert Tilt, Swap Pan-Tilt, Encoder Pan-Tilt, No DMX Signal, Display Power Save, Turn On Startup, Linear Color,Load Default, to confirm by press “OK” button.

1. Press “Run Mode” , and choose Run Mode by “UP&DOWN”，it will be show DMX and

Auto mode , to confirm by press “Ok” button.

2. Press “DMX Address Mode” , and choose DMX Address by “UP&DOWN”，it will be show

DMX Address 001-512 , to confirm by press “Ok” button.

3. Press “Channel Mode” , and choose Channel Mode by “UP&DOWN”，it will be show 16

or 20 , to confirm by press “Ok” button.

4. Press “Invert Pan Mode” , and choose Invert Pan by “UP&DOWN”，it will be show

ON/OFF , to confirm by press “Ok” button.

5. Press “Invert Tilt Mode” , and choose Invert Tilt by “UP&DOWN”，it will be show

ON/OFF , to confirm by press “Ok” button.

6. Press “Swap Pan-Tilt Mode” , and choose Swap Pan-Tilt by “UP&DOWN”，it will be show

ON/OFF , to confirm by press “Ok” button.

Advanced

password

DMX Monitor

Program run

Colour Wheel

Stop/Strobe

Dimmer

Gobo Change

Prism Insertion

Prism Rotation

Frost

Gobo Shak

Focus

Pan

Pan Fine

Tilt

Tilt Fine

Pan-Tilt speed

Reset

Lamp Control

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

10

7. Press “Encoder Pan-Tilt” , and choose Encoder Pan-Tilt by “UP&DOWN”，it will be show

ON/OFF , to confirm by press “Ok” button.

8. Press “No DMX Signal Mode” , and choose No DMX Signal by “UP&DOWN”，it will be

show KEEP/CLEAP , to confirm by press “Ok” button.

9. Display Power Save is screen saver. Press “Display Power Save” , and choose Display

Power Save by “UP&DOWN”，it will be show ON/OFF , to confirm by press “Ok” button.

10. Turn On Startup Mode is turn on the lamp when the turn on the power.Press “Turn On

Startup Mode” , and choose Turn On Startup by “UP&DOWN”，it will be show ON/OFF , to confirm by press “Ok” button.

11. Load Default Mode is Mode Rest. Press “Load Default Mode” , and choose Load Default by

“UP& DOWN”，it will be show Ok/Cancel, to confirm bypress “Ok” button.

 Manual Press “Manual” , and choose Manual by “UP&DOWN” ， it will be show Colour Wheel, Stop/Strobe, Dimmer, Gobo Change, Prism Insertion, Prism Rotation, Frost, Gobo Shak, Focus, Pan, Pan Fine, Tilt, Tilt Fine, Pan-Tilt speed, Rest, Lamp Control, to confirm by press “OK”

button.

1. Rest Model is the light rest

2. Colour Wheel, Stop/Strobe, Dimmer, Gobo Change, Prism Insertion, Prism Rotation,

Frost, Gobo Shak, Focus, Pan, Pan Fine, Tilt, Tilt Fine, Pan-Tilt speed model are Press the Ok then pressing ”UP&DWON” button, will show 001 to 255,. correcting by “OK” Button. …………………………

3. Lamp Control ,Press the OK then pressing ”UP&DWON” button, will show ON to OFF,.

correcting by “OK” Button.

 System

Press “System” , and choose by “UP&DOWN”，it will be show Software Version, Total Fixture Hours, Partial Fixture Hours, Total Lamp Hours, Partial Lamp Hours, DMX Monitor, System Errors mode,  Advanced

Advanced mode is the factory mode

Maintenance:

To prolong the life of the projector, some maintenance work has to be done to ensure the optical system in good condition. If the projector does not function, check the fuses on the power socket of the projector, they should only be replaced by fuses of the same specification. Should these be damaged, call a qualified technician before replacement. The projector has thermal protection device that will switch off the projector in case of overheating. Should either of these operate, check that the fans are not blocked, and if they are dirty, clean them before switching on the projector again. Check that the fans are operational, if not, call a qualified technician.

☆Any maintenance work should only be carried out by qualified technicians.

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

11

Keeping The Product Clean:

To ensure the reliability of the projector, it should be kept clean. It is recommended that the fans should be cleaned every 15 days. The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output.

Do NOT use any type of solvent on dichroic colour filters.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics. A soft cloth and typical glass cleaning products should be used for cleaning. It is recommended to clean the external optics at least once every 15 days and clean the internal optics at least once every 60 / 90 days.

☆Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.

Trouble Shooting:

Problem

Answer

The moving head light doesn’t switch on.

Check the fuse the power socket Replace the lamp

Although shines, but the moving head lamp doesn’t accept the instruction of the controller.

Check the digital start address and also check the connection situation of the communication control line

The moving head lamp only can work intermittently.

Inspect the power supply and voltage is whether normal.

Make sure the fan is working well or fans and their filters not blocked

Defective projection

Make sure the lamp is within its life limit Remove dust or grease from the lenses.

The beam appears dim

heck the optics is clean or the lens in good condition(not cracked) Replace with a new lamp of the specified type and rating.

☆Other maintain work should by the specialist which has the experience to carry on.

Equipment and Appendix:

☆ Beam 230W Moving Head Light 1pcs ☆ Power Cable 1pcs ☆ XLR connector 1unit ☆ Light Hook 2pcs ☆ The Product of Instruction 1pcs

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

12

Channel List:

20CH MODE

Channel

Value

Channel Mode

16CH

20CH

CH1

(Color)

0~8

White

8~15

Color1

16~23

Color 2

24~31

Color 3

32~39

Color 4

40~47

Color 5

48~55

Color 6

56~63

Color 7

64~71

Color 8

72~79

Color 9

80~87

Color 10

88~95

Color 11

96~103

Color 12

104~111

Color 13

112~127

Color 14

128~191

Rainbow effect with

veering(Fast~slow)

Rainbow effect with veering(Fast~slow)

192~255

Rainbow effect with inversion

(slow~Fast)

Rainbow effect with inversion

(slow~Fast)

CH2

(Strobe)

0

Off

1~50

Strobe ON

51~240

Strobe Speed (slow~Fast)

241~255

Turn on

CH3

(Dimming)

0~255 OFF~ON

OFF~ON

0~6

White

7~13

Gobo 1

14~20

Gobo 2

21~27

Gobo 3

28~34

Gobo 4

35~41

Gobo 5

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

13

CH4

(Gobo)

42~48

Gobo 6

49~55

Gobo 7

56~62

Gobo 8

63~69

Gobo 9

70~76

Gobo 10

77~83

Gobo 11

84~90

Gobo 12

91~97

Gobo 13

98~104

Gobo 14

105~111

Gobo 15

112~118

Gobo 16

119~127

Gobo 17

128~191

Rainbow effect with veering

(slow~Fast)

Rainbow effect with veering

(slow~Fast)

192~255

Rainbow effect with inversion

(slow~Fast)

Rainbow effect with inversion

(slow~Fast)

CH5

(Prism)

0~31

No function

31~255

Prism

CH6

(Prism

Rotation)

0~127

Angle

128~191

veering(Fast~slow)

192~255

inversion (slow~Fast)

CH7

(Frost)

0~255 Off- Frost

Off- Frost

CH8

0~255

Gobo shake

CH9

0~255

Focus

CH10

0~255

Pan

CH11

0~255

Pan Adjusting

CH12

0~255

Tilt

CH13

0~255

Tilt Adjusting

CH14

0~255

XY speed (Fast~slow)

CH15

0~254

No function

255

Reset

CH16

(lamp control)

0~100

No function

100~105

Delay closing

106~199

No function

200~205

Delay open

206~255

No function

CH17

0~255 Marco function

CH18

0~255 Color speed

CH19

0~255

Dimmer-prism-frost speed

CH20

0~255 Gobo speed

LED Beam 230 MJ-1016A User Manual ver2.0

www.mjledlighting.com

14

Technical Parameters:

Voltage : 90~240V/50-60Hz Power consumption:380W@(220V) Bulb: Arclite MHD7R230 230W projection lamp Lamp : Arclite MHD7R230W , Color temperature : 8500K Color: 14 color + blank color wheel Gobo: 17 fixed gobo + blank gobo Prism : rotation 8-face prism, Bilateral rotation .frost function Dimmer : 0-100% linear adjustment ,Strobe(0.5-9 times/ second) Beam angle : parallel beam angel 0 – 4° Channel : 16/20CH Control mode : Standard DMX512, Automatic,Sound and Master/slave mode Pan: X axis 540°automatically accurate positioning Tilt:Y axis 270°automatically accurate positioning Control Panel: LCD touch screen display panel with buttons Protection grade:IP20 Net weight:16KG Gross Weight: 18.5 kg Package Size: 450 x 430x 530cm Light Size(see it below)

Mega MJ-1016A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual