Page 1
TTVV RReemmoottee CCoonnttrrooll TTuunneerr
Content
Safety Instructions .............................................................. 2
Battery disposal ............................................................... 2
Summary........................................................................... 3
TV card ........................................................................... 3
Remote control ................................................................ 4
Inserting batteries ......................................................... 4
Button Layout ............................................................... 5
Changing the transmission/reception channels...................... 8
Operation........................................................................... 9
Inserting the TV card ........................................................ 9
Removing a PC card.......................................................... 9
Connections..................................................................... 9
Watch TV....................................................................... 10
Customer Service.............................................................. 11
Troubleshooting ............................................................. 11
Check cables and connections........................................ 11
Technical support ........................................................... 11
Additional Support .......................................................... 12
Page 2
S
AAFFEETTYY
S
Keep the components in a safe place.
**
I
NNSSTTRRUUCCTTIIOONNS
I
 Please follow the safety instructions in your
notebook’s directions for use.
S
BATTERY DISPOSAL
 Important: Batteries are special category waste and
must be disposed of properly. Replace the batteries
only with batteries of the same or an equivalent type.
2
ENGLISH
Page 3
S
UUMMMMAARRY
S
Y
TV CARD
Your TV card possesses the following connections:
n o p
Ref. Name Function
s
r
q
n
o
p
q
r
s
Antenna connection For radio reception
Antenna connection For TV reception
DC In To power source
Video IN Composite
Video IN S-Video
Audio input (Aux)
For recording and if
necessary processing video
data (e.g. camcorder, ...)
For feeding external
analogue audio sources
SUMMARY
3
Page 4
REMOTE CONTROL
This wireless remote control set controls the Home Cinema
program on your notebook. In order for this to work, the following
requirements must be met:
- The notebook must be booted up.
- Windows® XP must be fully loaded.
- The driver software must be installed*.
- Home Cinema installed*.
* All these conditions are met in the delivered state.
INSERTING BATTERIES
1. Turn the remote unit round.
2. Remove the cover of the battery
compartment by pushing it in the
direction indicated.
3. Remove the used batteries if
necessary and dispose of them
properly.
4. Place in two new type AAA (round
cell) batteries.
5. Replace the cover of the battery
compartment by pushing it in the
direction indicated.
4
ENGLISH
Page 5
BUTTON LAYOUT
TV
Video
CD/
DVD
Audio
Radio
On / Off
View and record
television
programs.
View video
recordings.
Playback music
CDs, video disks
and DVDs.
Start video text
application.
Open music
archive.
Listen to and
record radio
programs.
EPG function (Electronic Program Guide)
Open photo archive.
Application-related information function.
Start Selection Menu of the application
Photo
Info
Menu
running.
Press Scrolling
Wheel
= OK
You select the required function with these
navigation Buttons. The selection indicator will
move in the appropriate direction. The
Scrolling Wheel can be turned up or down.
Press the Scrolling Wheel to confirm your
selection.
Back
Reverts to the point selected previously.
Information: The functions described here are
standard functions.
These Buttons can differ according to the operating
mode (TV, video, photo, etc.).
SUMMARY
5
Page 6
+
Press to
increase the
volume; press
+
to lower the
volume.
The D-Button
lights up if a
Button on the
remote is
operated. It
serves to select
certain
functions.
+
P
Press to
select the next
channel (TV,
+
radio). You
select the
previous channel
with .
;
Mute Switch (Switches the sound output off).
Selects the TV channel used last.
Special function Button (e.g.: Selection of the audio
track)
Special function Button (e.g.: Subtitle selection)
Special function Button (e.g.: Camera selection)
Special function Button (e.g.: Chapter selection)
6
ENGLISH
Page 7
Ends the
playback/
recording
Pauses the
playback at the
selected point.
Starts
playback.
Previous
title/images
Snapshot from
the current
channel
Next
title/images
Rewind
0
Start recording
Fast forward
Direct selection of the TV channels by
3 2 1
means of numbers. Number entry in the
6 5 4
case of some functions (video text, etc.).
9 8 7
SUMMARY
7
Page 8
CHANGING THE TRANSMISSION/RECEPTION
CHANNELS
If several computers with remote controls are set up in close
proximity of each other (approx. 10 metres), this can lead to
disturbance. This can be remedied by choosing different channels.
Only reset the remote control in case of disturbances.
Proceed as follows:
1. Start the program Power Cinema in the program folder
Home Cinema.
2. Choose the menu item Settings and in the following
screen Set Remote Control Channel.
3. Detailed instructions on how to set the channel for the
remote control will appear on screen. Follow the onscreen
instructions.
8
ENGLISH
Page 9
O
PPEERRAATTIIOON
O
The TV card fits into the PCMCIA bay of your notebook
N
INSERTING THE TV CARD
1. After Windows® has started carefully insert the card into the
appropriate bay. When the card is fully inserted, two short signal
tones will be played to confirm successful installation.
2. Now connect one end of the supplied USB cable to the TV card
and the other end to a free USB port of your notebook. This
serves as an additional power source and must always be
connected when the TV card is used.
3. To setup the TV card start the application for TV reception. An
installation assistant will guide you through the program.
REMOVING A PC CARD
Remove the TV card in the following manner:
1. Disconnect all cables.
2. Remove the TV card and store it in a safe place.
CONNECTIONS
An additional 75 Ohm coaxial antenna cable is required to enable
TV / radio reception
1. Connect the coaxial antenna cable with the antenna connector
(o) for TV reception and wit the antenna connector (n) for radio
reception.
2. Connect the other end of the coaxial antenna cable to an aerial
antenna or to cable TV.
Attention: It is important that you pull out the antenna cable,
when the device is not in use, especially during thunderstorms.
In this way you protect your device from a potential power surge
caused by lightning.
OPERATION
9
Page 10
WATCH TV
If you want to watch TV with your notebook you need special
software. This is already installed and can be found in All
Programs, Home Cinema.
The following table gives a summary of this program group:
Medi@show For showing presentations
Power Cinema SE For playing TV, videos, photos,
films and music
Power Director For processing videos
Power DVD For playing DVDs
Power Producer For putting together your own
DVDs from films and photos
You will find additional help by pressing the F1 key.
The execution of an autoscan will be necessary to watch TV. You
will start the scanning procedure by selecting Settings Ö
Autoscan.
You can control the program with the remote control.
Caution: Audio and video recordings can occupy a lot of memory
(up to 2.4 GB per hour). We recommend that you save your audio
and video recording files to rewriteable media or save them on
the directory D:.
10
ENGLISH
Page 11
C
UUSSTTOOMMEERR
C
S
EERRVVIICCE
S
E
TROUBLESHOOTING
Errors can have simple causes, but sometimes they are caused by
faulty equipment.
HECK CABLES AND CONNECTIONS
C
Visibly check all cables and connections. Should all lights be off,
check whether all equipment is supplied with power.
Switch off the Notebook and check all cable connections. Check
the connections to peripherals. Do not exchange cables, even
though they may look similar. The polarity in the cables may be
different. When it is confirmed that the Notebook has power and
all connections are correct, turn the Notebook on again.
TECHNICAL SUPPORT
This equipment has been extensively tested in our laboratories
with a large number of compatible devices. It fulfills all required
standards and complies with the standard “Designed for Windows”,
which certifies utmost compatibility. However, the software
drivers for individual components are updated from time to time.
This is a regular process provided by the manufacturer to mend
possible compatibility problems that may occur with components
(e.g., programs or hardware) that were not tested at the time of
your Notebook’s manufacture. Driver updates and the latest
information on your product are available on the Internet.
CUSTOMER SERVICE
11
Page 12
ADDITIONAL SUPPORT
If the suggestions in the above section have not solved your
problem, please contact customer care and we will attempt to
help you solve the problem. Before you call, however, please have
the following information available:
- How is your computer configured?
- What additional peripherals do you use?
- What messages, if any, appear on your screen?
- What software were you using when the error occurred?
- What steps have you already undertaken to solve the
problem?
- Have you upgraded or removed drivers or hardware?
- Can you manually repeat the problem?
- If you have been given a customer number previously, please
have this available.
12
ENGLISH
Loading...