Before using the remote control, please read these operating
instructions carefully. Please keep the instruction manual for
consultation purposes or for possibly handing it over to third parties.
Do not try to repair the remote control yourself.
The universal remote control is equipped with a class 1M infrared diode.
Do not look at the laser using optical instruments!
Do not expose your remote control to dust, intense sunlight, humidity, high
temperatures or mechanical shocks.
Old and new batteries must never be combined.
Do not use any corrosive or aggressive cleansing agents.
Scope of application
This universal remote control is designed to control 8 devices such as:
TV TV with teletext
VCRVideo recorder
DVDDVD player
CDCD player
ASATAnalogous satellite receiver
DSATDigital satellite receiver
CBLPay TV decoder
AUXfor additional devices (TV, VCR, SAT, CD, DVD,...)
Please note:
The designations on the MODE keys like "TV", "VCR" etc. have the only
purpose to facilitate their identification. You can of course assign other
types of device to these keys.
1
Manual URC 4689 UK Apr05.fm Seite 2 Montag, 11. April 2005 12:00 12
Overview
Inserting the batteries
Insert 2 LR03/AAA or R03/AAA batteries; we recommend you to use of
alkaline batteries.
1. Open the cover on the back of the remote control.
2. Check the +/– polarity on the batteries and inside the compartment.
3. Insert the batteries.
4. Close the cover.
When exchanging the batteries, it may be necessary to reprogram the
unit. Hence it is advisable to record the codes needed for your devices.
Used batteries do not qualify as household waste. The batteries must
be disposed of at a special collection point for used batteries.
2
Manual URC 4689 UK Apr05.fm Seite 3 Montag, 11. April 2005 12:00 12
Programming the device codes
The codes of the respective devices can be found in the code list attached to
these operating instructions. Proceed as follows:
1. Switch on manually the device you wish to control (TV, VCR etc ...).
2. Keep the SET key pressed for approx. 3 seconds until the LED indicator
5. Enter the 3-digit code from the code table; the LED turns off each time
you press a key.
6. If you entered is code correctly, the LED turns off after the last digit has
been entered. If an invalid code is entered, the LED will flash for three
seconds before going out.
7. The code entry is finished.
Should the device not respond as you expect it to do, you can try to
repeat the programming using another code. Please try all the codes
indicated for your brand. Select the code that makes your device
respond correctly to any command available on your remote control!
If you failed this way, then have another try with the search method
described in the chapter "Automatic code search".
Code search (manual search)
To run a manual code search, proceed as follows:
1. Switch on manually the device you wish to control (TV, VCR etc ...).
2. Keep the SET key pressed for approx. 3 seconds until the LED indicator
5. Press several times in succession (up to 350 times) the "POWER" or
"PROG" (channel upwards) or "PLAY" (only for a VCR) key until the
device to be controlled has been switched off or responds.
6. Briefly press the OK key for storing the code.
In view of the extensive number of different code numbers, up to 350 different
codes have already been pre-programmed per device type. It is possible that
only the most common main functions will be available in individual cases. In
case of some special device models, the procedure described may fail to be
successful. – The Code search starts with the 3-digit number stored at the
moment.
Code search (automatic search)
An automatic search allows you to find even codes of brands that are not
stated in the code list. Proceed as follows:
1. Switch on manually the device you wish to control (TV, VCR etc ...).
2. KKeep the SET key pressed for approx. 3 seconds until the LED indicator
5. Point the remote control at the device you wish to control and press the
CHAN+ key once briefly. If the device does not possess a channel
function, then press the PLAY or POWER key instead of CHAN+.
The remote control starts the search and sends a code every second.
Each time a code is sent, the LED will light up.
3
Manual URC 4689 UK Apr05.fm Seite 4 Montag, 11. April 2005 12:00 12
6. As soon as the device does respond to the remote control, press OK.
7. Should you fail to press the OK key in time, you can step by step return to
the code to which the device has responded using the CHAN– key.
If you want the remote control only to send a new code every 3 seconds instead
of every second, proceed as follows:
Press and release CHAN+ (or PLAY or POWER) twice (see step 5). This will
give you more time, but the procedure will also take longer.
Code search by brand
This function provides you with the possibility of searching by brands. You will
find the brands in the code table under "Search code under brand name".
Proceed as follows:
1. Switch on manually the device you wish to control (TV, VCR etc ...).
2. Keep the SET key pressed for approx. 3 seconds until the LED indicator
lights continuously.
5. Enter the applicable one-digit code from brand code table „Search code
under brand name“.
If you enter the digit „0“, all brands will be searched.
6. Press the CHAN+ key (or, in case of video cassette recorders, POWER or
PLAY) until the device responds correctly. Proceed swiftly when doing
this, otherwise the automatic code search will be started.
7. Store the code by pressing the "OK" key.
If all codes have been searched, the LED will blink for about 3 seconds.
Code identification
The code identification allows you to identify codes that you have already
entered and that are memorised in the remote control. Proceed as follows:
1. Keep the SET key pressed for approx. 3 seconds until the LED indicator
lights continuously.
2. Release the SET key.
3. Briefly press the desired mode key (TV, VCR, DVD, SAT, DSAT, CD, CBL,
AUX). The LED blinks.
4. Briefly press the SET key. The LED blinks again.
5. To find the first digit, press each number key from 0 to 9 until the LED
turns off. The number you pressed is the first digit of the code. To
determine the second and the third number, repeat the procedure.
6. The LED will go out as soon as the key for the third number has been
pressed.
7. The code identification has now been completed.
Learning function
The universal remote control provides you with the possibility of manually
storing certain special functions which have not been stored, or even devices
which have not been included in the code list. To do this, the original remote
control of your device is required in any case. However, please note the
following tips beforehand in order to avoid any mistakes.
• Use new batteries for both remote controls.
• You can assign one remote control to each of the MODE keys.
4
Manual URC 4689 UK Apr05.fm Seite 5 Montag, 11. April 2005 12:00 12
• Place the remote controls with the infrared diodes on a table so that they
point each other at a distance between 15 and 50 mm.
• You can store up to 150 commands. When the memory is full, the backlight
illumination of the MODE key will blink for 3 seconds.
• Each programming of a key can take approx. 3 seconds.
• Always chech that the key you wish to teach a code is free or does not
correspond to an important function.
• The following keys cannot be programmed with functions: LEARN, SET, ALL
OFF, P<P, SHOWVIEW and all MODE keys.
• First have a try by programming any desired code and testing it then.
Thereafter, delete all codes and proceed with the proper programming.
Do not use the learn function beneath an energy saving lamp.
Programming functions
1. Keep the SET key pressed for approx. 3 seconds until the LED indicator
All learned commands entries under that mode are now cleared.
Deleting all commands under all modes
1. Keep the SET key pressed for approx. 3 seconds until the LED indicator
lights continuously.
2. Release the SET key.
3. Press and release the LEARN key twice.
4. Press the SET key.
All learned command entries are now cleared.
5
Manual URC 4689 UK Apr05.fm Seite 6 Montag, 11. April 2005 12:00 12
ALL OFF function
You can switch off all pre-programmed devices simultaneously. Proceed as
follows:
1. Briefly press the ALL OFF key. The selected device will be switched off
and the corresponding MODE key will light up.
2. Press the ALL OFF key immediately once again and keep it pressed for
approx. 3 seconds. Now, all pre-programmed devices are switched off one
after another. This will take about 3 seconds. Then, the MODE key
illumination will go out. The remote control has to be pointed at the
devices to be operated until the MODE key goes out.
Some devices can be switched on and off by means of the POWER key. These
devices will be switched ON with the ALL OFF function if they were turned
OFF.
Toggle function
You can zap between 2 channels by pressing the P<P key. Proceed as follows:
1. Switch on manually the device you wish to control (TV, VCR, ...)
2. Keep the SET key pressed for approx. 3 seconds until the LED indicator
lights continuously.
3. Release the SET key.
4. Press P<P and the mode key of the device you wish to control.
5. Enter the first channel number (3 digits as maximum).
6. Press again P<P and the mode key of the device you wish to control.
7. Enter the second channnel number (3 digits as maximum).
8. Press P<P to end the setting.
Certain TV sets have also a toggle function (depending on the manufacturer, it
can zap from the present and the previous channel). This function can be
activated by pressing the A/V or -/-- keys on your remote control.
Autozapping
In case of TV operation, you will successively go through all stored channels by
once pressing the SHOWVIEW key (the remote control has to be pointed
permanently at the device). Press the CHAN– key once to finish the function.
Normal operation
After having programmed your remote control for your audio/video devices,
your remote control will in respect of the most common main functions work
like the original remote control of the respective device.
Point your remote control at the respective device and press the appropriate
MODE key. All functions will now be activated by pressing the respective
function key of your remote control.
For each transmitted IR signal, the LED lights up.
6
Manual URC 4689 UK Apr05.fm Seite 7 Montag, 11. April 2005 12:00 12
Universal functions
The universal functions allow you to perform certain functions on another type
of device than the selected one.
Example: The last selected appliance is a VCR, but you would like to control the
volume of your TV.
Proceed as follows:
1. Press the TV mode.
2. Keep the SET key pressed for approx. 3 seconds until the LED indicator
lights continuously.
3. Release the SET key.
4. Keep the MUTE key pressed for approx. 8 seconds until the MODE key
flashes a second time.
SHIFT function
Some keys of the universal remote control can be allocated twice. To use these
functions, briefly press the "SET" key (MODE key lights up) and then the key
controlling this second function.
Troubleshooting
The remote control does not work
• Check whether your devices are correctly connected and switched on.
• Check whether the batteries of the remote control are correctly inserted and
whether the polarity + / - matches with the marks.
• If the batteries are too low, replace them by new ones.
Several device codes are listed under the brand of my device. How can I
determine the right device code?
• To determine the right device code for your device, try the codes successively
until most of the functions of the device are working properly.
The devices only respond to a few instructions of the remote control.
• Test further codes until the devices respond appropriately to the commands.
• If in some exceptional cases neither a manual code entry nor the automatic
code search are successful, your device may be incompatible with your
universal remote control.
7
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.