Page 1
A Global Leader in the Design, Development, and
Part
Customer
Contact Data
Rated Power
Any
Switching Voltage
DC or
Switching Current
DC
Carry Current
DC
Contact Resistance
@
Breakdown
According
Operating
Incl. Bounce; Measured with w/ Nominal Voltage
Release Time (max.)
Measured
Insulation
Rh<45
Capacitance
@
Manufacture of Sensor and Magnetic Components
Series Datasheet – H Reed Relays
H Series
Reed Relays
Features: High Voltage Relay, Open Frame with M4 Screw Mount
Applications: Test and Medical Equipment & Others
Markets: Medical, Test and Measurement & Others
Description: H 00- 1 X 00
www.standexmeder.com
Nominal Voltage Contact QTY Contact Form Switch Model
12, 24 1 A, B 69, 83
Options
(max.)
DC combination of V&A not to exceed their individual max.’s
(max.)
peak AC
(max.)
or peak AC
(max.)
or peak AC
(max.)
0.5V & 50mA
Voltage (min.)
to EN60255-5
Time (max.)
with no Coil Excitation
Resistance (typ.)
%, 100V Test Voltage
(typ.)
10kHz across open Switch
Switch Model
69 83
50 50 W
10,000 7,500 V
3.0 3.0 A
5.0 5.0 A
150 150 mOhm
15 10 kVDC
3.0 3.0 ms
1.5 1.5 ms
10
10
10
10
1 1 pF
Unit
Ohm
USA: +1.866.782.6339 │ salesusa@standexmeder.com
Europe: +49.7731.8399.0 │ info@standexmeder.com
Asia: +86.21.37820625 │ salesasia@standexmeder.com
Modifications in the sense of technical progress are reserved.
Version 01
27.01.2015
Page 2
A Global Leader in the Design, Development, and
H Reed Relay
Environmental
Shock Resistance (max.)
1/2 sine wave duration 11ms
Vibration
Operating Temperature
Storage Temperature
Soldering
5 sec. max.
Life Test Data
*Load increase reduces life
Glossary
Form
NO = Normally Open Contacts
SPST = Single Pole Single
Form B
NC = Normally Closed
SPST
Form C
Changeover
SPDT = Single Pole Double
Nominal Coil Power
Contact
Switch
The Pull
*
Handling
consideration, including a too high packing density. This may
Mechanical shock impacts e.g. dropping the relays may cause
Manufacture of Sensor and Magnetic Components
Series Datasheet – H Reed Relays
Coil Data
Form
1A 69, 83
1B* 69, 83
Re-closure of Form B may occur if the max. coil voltage is exceeded. Coil polarity on Form B must be observed. Pin 2 is positive.
Model
Unit VDC Ohm VDC VDC mW
-In / Drop-Out Voltage and Coil Resistance will change at rate of 0.4% per °C.
Data Unit
Resistance (max.)
Temperature (max.)
Coil Voltage
-35 to 95 °C
www.standexmeder.com
Coil Resistance
(nom.)
(typ.)
12 230 8.4 1 620
24 700 18 2 822
12 180 8.4 1 800
24 360 16.8 2 1,600
50 g
20 g
-20 to 70 °C
260 °C
Pull-In Voltage
(max.)
Drop-Out Voltage
(min.)
(typ.)
& Assembly Instructions
Switching inductive and/or capacitive loads create voltage
and/or current peaks, which may damage the relay.
Protective circuits need to be used.
External magnetic fields needs to be taken into
influence the relays’ electrical characteristics.
immediate or post-installation failure.
Wave soldering: maximum 260°/5 seconds.
Reflow soldering: Recommendations given by the soldering
paste manufacturer need to be considered as well as the
temperature limits of other components/processes.
Contact Form
A
= Single Pole Single Throw
Contacts
Throw
Throw
expectancy of Reed Switches
USA: +1.866.782.6339 │ salesusa@standexmeder.com
Europe: +49.7731.8399.0 │ info@standexmeder.com
Asia: +86.21.37820625 │ salesasia@standexmeder.com
Modifications in the sense of technical progress are reserved.
Version 01
27.01.2015
Loading...