Mean Well KDA-64 Instruction Manual

KDA-64 KNX to DALI Gateway

Instruction Manual

KDA-64 Instruction Manual

Content

1.Using the application program ..............................................................

.................................................................

............................................................

................................................................

.......................................................................

..............

....................................................................

..................................................

.............................................

...............

............................

...

...............................

..............................................................................

.....................................................................................

....................................................................................

..........................................................

................................

.....................................................

....................

1
1

1
1

3

8

20

31

34

31
32

34
36

22
25
26
27

9

5
6

2.General product information

2.1 DALI Bus system properties

2.2 KDA-64 product features

3.1 Installing the Plug-In

4.1 Commissioning with KDA-64 via web site or pushbuttons

6.1 Configuration buttons

7.1 Special functions in 'Normal Mode

7.2 Special functions in 'Extended Mode'

7.1.1 Synchronisation with the connected DALI segment

7.1.2 User-friendly names for ECGs and groups

7.2.1 Preparation and planning the DALI commissioning in 'Extended Mode

7.2.2 DALI commissioning in 'Extended Mode'

6.2 Control buttons

6.3 ECG fields

6.4 Group fields

6.5 Information and status fields

4.2 Commissioning with KDA-64 via ETS Plug-In

3.2 Principal structure of the Plug-In

3.3 Operating modes of the Plug-In: DALI commissioning

........

.............................................................................

...........................................................

........................................................................

...........................................

3

8

10
16

31

3.General properties of the ETS application program: KDA-64 Plug-In

4.DALI commissioning

5.Display and push-button control

6.Control via web browser

7.ETS Special and commissioning functions

Sep. 2017 Version 0

KDA-64 Instruction Manual

Content

....

................................

.................................................

.......................................

.............................................................

...........................................

..............................................

..........................

..................................................................................

..........................................................

......................................

........................................................

.......................................................

........................................................................

............................................................................

..............................................................................

.............................................................................

................................................................

......................

..................................................................................

...............................................................

39
40

41
41
42
38

43
44

45

49
49
50
51

52

45
46
47
47
47
48
49

7.2.4 Using dummy ECGs in 'Extended Mode'

7.3.1 Using IP for plug-in communication

7.3.2 Parameter templates

7.3.3 DALI configuration data back-up

7.3 General extra functions in the ETS

8.1. Quick exchange of individual ECGs

8.2 Extending the existing system – post-installation

9.1 Normal mode

10.1 Recording operating hours

10.2 Individual fault recognition at ECG level

10.3 Fault analysis at group level

10.4 Fault analysis at device level

11.1 The scene module

9.2 Permanent mode

9.3 Staircase mode

9.4 Night-time mode

9.5 Panic / emergency mode

9.6 Test mode for central battery emergency luminaires

9.7 Burn-in mode

9.8 Operating mode hierarchy

.......................................................

...................................................................

...........................................................

.............................................................................

43

45

49

52

8. DALI maintenance and expansion

9. Different operating modes

10. Analysis and service functions

11. Scenes and effects

7.2.3 ECG and lamp faults during DALI commissioning in 'Extended Mode'

.......................

52

11.1.1 Scene programming via the scene website

KDA-64 Instruction Manual

Content

..............

........................................................................

......................................................................................

....................................................

.............................................................

..................................................................................

................................................................................

.................................................................

...........................................

....................................................................................

.........................................

....................

...................................

............................................

..............................................

.................................

.............................

............................................

..............................

.............................

.............................

.........................................

...............

53
55

59

61

72

77

83

59

67

60

70

55

72
73
74
75

76

78
80
81
83

84

57

11.2 The effect module

12.1 Features

13.1 General communication objects

14.1 Device: General settings

14.2 ECG No. xx

14.3 Group No. xx

12.2 Converter inhibit mode

13.2 ECG-related communication objects

12.3 Test mode

13.3 Group-related communication objects

..........................................

...............................................

...................................................................

58

61

72

12. Self-contained battery emergency lamps

13. ETS communication objects overview

14. ETS parameter overview

11.1.2 Scene programming via ETS in 'Extended Mode

11.2.1 Effect programming using the effect website

14.1.1 Parameter page: General Settings

14.1.2 Parameter page: IP Settings

14.1.3 Parameter page: Behaviour

14.1.4 Parameter page: Special Functions

14.1.5 Parameter page: Analysis and Service

14.2.1 Parameter page ECG No. xx

14.2.2 Parameter page: Emergency Settings

14.2.3 Parameter page: Switching Behaviour

14.2.4 Parameter page: Analysis and Service

14.3.1 Parameter page: Group No. xx

11.2.2 Effect programming via ETS in 'Extended Mode'

KDA-64 Instruction Manual

Content

.............................

.............................

85
87

.............................................................

...........................................................

87
88

15. Firmware version and update

16. Reset to conditions at delivery

14.3.2 Parameter page: Switching Behaviour

14.3.3 Parameter page: Analysis and Service

1

1. Using the application program

Product family: Lighting
Product type: Gateway
Manufacturer: Mean Well

Name: KDA-64

2. General product information

2.1. DALI Bus system properties

The cross-functional DALI-Bus (DALI = Digital Addressable Lighting Interface) is a
system used to control electronic ballasts (ECGs) in lighting technology. The
specifications of the DALI communications interface are set in the international
norm IEC 60929.

The DALI Bus enables the receipt of switch and dim commands. In addition, the
DALI can be used for the notification of a fault status such as light or ECG failure or
for other light status information. In line with the latest DALI standard, devices with
emergency light function (EN 62386-202) are also supported. Status and operating
mode of emergency lights can be monitored and different prescribed testing
procedures can be performed.

Via the connected control device / gateway (Master), up to 64 individual DALI ECGs
(Slaves) can be connected in a DALI segment. When the DALI is commissioned, the
ECGs receive an automatically generated 3byte long address. Based on the long
address a short address between 0 and 63 is assigned during the further
commissioning process. As the address assignment is automatic, the device order
is random. The individual ECGs/lights therefore need to be identified during the
further commissioning process (see below).

The addressing of individual ECGs in the system is either based upon the short
address (individual addressing) or upon a DALI group address (group addressing).
For this purpose, any number of ECGs within a segment can be assigned to up to 16
groups. The group addressing in the DALI system guarantees that switch and dim
processes of different lights within a system are performed simultaneously without
imposition of time delays.

In addition to short and group addresses, the light values of individual DALI ECGs
can also be merged into scenes and addressed via scene addresses.

For a detailed description of the DALI system, please see the DALI handbook at
https://www.digitalilluminationinterface.org/

2.2. KDA-64 product features

The KDA-64 is a device used to control ECGs with a DALI interface via the KNX
installation bus. The device transforms switch and dim commands from the
connected KNX system into DALI telegrams and status information from the DALI
bus into KNX telegrams. The KDA-64 is a Category 1 device (in accordance with EN
62386-103). This means the device must only be used in DALI segments with

2

connected ECGs and not with other DALI control devices within the segment (no
multi-master function).

Power supply for the up to 64 connected ECGs comes directly from the KDA-64. An
additional DALI power supply is required and permitted.not not

The device comes in a 4TE wide DIN Rail casing so it can be directly integrated into
the mains distribution box.

In addition to the pure gateway functions, the
KDA-64 offers numerous additional features:

● Addressing of 16 DALI groups and/or individual addressing of up to 64 ECGs

● Flexible DALI commissioning concept: directly on the device or via the integrated
web server

● Different operating modes for groups and ECGs such as permanent mode, night-

time mode or staircase mode

● Burn-in mode for each individual light with specific burn-in time settings

● Integrated reader to count the operating hours of each light with an alarm to signify
the end of its life span

● Individual fault recognition with objects for each light/ECG

●Complex fault analysis at group and device level with number of faults and
calculation of fault rates

● Fault threshold monitoring with individually adjustable threshold values

● Scene module for extensive scene programming of groups and individual ECGs

● Effect module for sequence control and light effects

● “Quick exchange function“ for the quick and easy replacement of faulty ECGs

● Test mode for centrally powered emergency light systems

● Support of self contained emergency ballasts-

3

● Support of testing procedures for emergency lights with date and time stamp

●Integrated web server with extensive commissioning and maintenance

possibilities

● Integrated “visualisation“ via web-browser for direct control and display

3. General properties of the ETS application program: KDA-64

3.1 Installing the Plug-In

The application for the KDA-64 is based on a powerful KNX communications stack
of the System-B type. It is designed as plug-in for ETS-3 ETS-4, and ETS-5. The,
plug-in design means that an additional installation process is necessary. All
program files that are required are automatically set up when you import the
corresponding ETS product file (knxprod file).

After the import the product can be integrated as usual into the ETS. When you first
load the product in the ETS, you need to start the installation of the required plug-in
files by pressing the 'Next' button.

If it didn't pop-up pulg-in setup window during importing KDA-64.knxprod file, you
may find plug-in install as following example:

- Drag KDA-64 into the project e.g. Dining room

- Roll down dining room tab , find “1.1.1 KDA-64”

- Right click “1.1.1 KDA-64”, select “Plug-in” to install plug-in program.

4

And follow the instructions:

If the installation has been successful, a notification window appears.

5

And, „open product specific parameter dialog“ is able to be used in parameter tab. If
plug-in didn't be installed properly, this function is not available. Later on we will
discuss more about parameter.

Attention: The PC must have .NET Version 4.0 as a requirement for the installation.
Normally the framework exists on any modern PC. Should an older version of .NET
be installed or no version at all, you need to update .NET first. Please see the
Microsoft website for the required setup.

3.2 Principal structure of the Plug-In

The KDA-64 is a high-functionality product and accordingly offers many different
setting options within the parameters. To make the overview of the parameters as
simple and transparent as possible for the system integrator, there are more
operating levels than with a standard ETS application.

6

Unlike with the standard applications, there is not only a parameter page for each
device within the main parameter directory on the left-hand side but also several
sub-pages which can be selected via a register at the top of the page. Use the main
directory to select the element you require “General ECG No XX, Group No XX“ and
the sub-pages to set the parameters of the selected element. This structure is
different from a standard device.

You can also use the three menus “Data,Tools and Help“ in the header of the plug-in
window to perform some of the main functions and settings.

3.3 Operating modes of the Plug-In: DALI commissioning

In principle, the plug-in can be used in the two different operating modes “Normal
mode“ and “Extended mode“. Depending on the concept needed for the DALI
commissioning, you can select the required mode in the menu 'Tools' 'Options'.

7

The choice of the commissioning concept depends on the preferences of the system
integrator as well as the technical requirements of the project. If you choose option
A 'Normal Mode' the DALI configuration and commissioning must be performed via
the website of the device.This means that all project gateways - at least during the
commissioning phase - must be integrated into an IP network via the IP interface.
(The network can also be a simple cross-link cable connection between the gateway
and the configuration PC.)

If no IP network is available, only a limited commissioning process is possible via
the display and push-buttons on the device. However, if you choose commissioning
option B “Extended Mode“ the whole commissioning process can be performed via
ETS and KNX. No IP network is required in this case. Mode B also gives you the
opportunity to configure individual ECGs 'offline' in the ETS, i.e. before they are
commissioned in the installation. However, in this case all objects and parameters
are visible. The synchronisation that simplifies the ETS and brings it in line with the
actual system is not possible.

To decide which mode to use you should answer the following three questions:

` Is the DALI gateway (at least temporarily during the commissioning process)

integrated into an IP network?

o Yes Mode A or mode B
o No Mode B

` Do you want to set the DALI configuration and parameters 'offline' in the ETS

prior to the commissioning of the installation?

o Yes Mode B

` Do you want to perform the DALI configuration and set the parameters on the

construction site and synchronise the ETS with the real installation to
simplify it?

o Yes Mode A

Mode A: 'Normal Mode' --- Mode B: 'Extended Mode'

If the conditions permit it, we recommend using 'Normal Mode', especially for
integrators who are not too familiar with the DALI system because the large number
of possible parameter settings and objects can be automatically reduced to those

8

elements that are actually required. The standard setting after the initial installation
of the plug-in is therefore mode A.

Please remember that whichever operating mode you select, it applies to all
gateways within a project and ETS. It is not possible to select mode A for some and
mode B for others.

4. DALI commissioning

As explained above, the work flow for the commissioning of a DALI segment differs
depending on the selected concept. The following chart shows the general

4.1 Commissioning the KDA-64 via website or pushbuttons

If you select option A, i.e. commissioning the device via the website or pushbuttons,
please use the following procedure.

Following the physical installation and wiring of the ECGs and lights and the
electronic commissioning, the connected ECGs need to be taught-in. During the
teach-in process, all DALI ECGs are automatically recognised and each ECG is
assigned a short address between 0 and 63.

You can start this process either via the pushbuttons and menu on the device
display (see below display and push button control) or via the commissioning
website (see below control via web browser).

KDA-64 Plug-In

9

The order of the ECGs within a DALI segment is completely random. You therefore
need to identify the ECGs and - if required - assign them to groups. Identification
and group assignment can also be performed via the device itself (pushbuttons,
display) or via the website. If you use the website for identification, you can give
each ECG an individual name (e.g. office-left). If you want to control an ECG as part
of a DALI group rather than individually, you can at this point assign it to a group.

Once you have identified all ECGs and, if required, named and assigned them, you
need to synchronise the ETS application. During the synchronisation, the system
properties of the connected DALI segment are transferred to the ETS and the
parameters and communication objects are configured accordingly. This means that
after the synchronisation only objects and parameters of actually existing ECGs are
visible to the user. The application is thereby optimised and simplified. ECG and
group names are also transferred to the ETS. To start the synchronisation, press
the respective button on the ETS parameter page (see below ETS application
program).

Once the synchronisation is complete, you can configure the individual ECG or
group parameters in the ETS and connect communication objects with group
addresses.

When you have finished the configuration, simply download the ETS application
onto the device.

In principle, the installation is now ready for operation and function testing.
However, if you would also like to program scenes or effects, you can do so via the
pushbuttons and display on the device (only scenes and with limited functionality) or
via the web site (scenes and effects without limitation).

For a complete description of the display and push-button control required for the
commissioning, please see chapter 5. For a description of the website function,
please refer to chapter 6.

4.2 The commissioning process with KDA-64 via ETS Plug-In

Instead of commissioning via web browser or push-buttons, the DALI can also be
entirely commissioned via KNX and the plug-in. This mode B option enables a
largely 'off-line configuration' of the DALI installation. Parameters for ECGs and
groups as well as communication objects can be completely configured before the
electrical installation. Names can be assigned in advance and the setting of scenes
and effects is also possible 'offline'.

This means that the system integrator who uses the ETS and the electrician who
works on the actual installation can work independently of each other. Once the
electrical installation is complete, the actual DALI commissioning can also be
performed with ETS.

The first thing to do is to start the teach-in process. During this process all
connected DALI ECGs are automatically recognised and each ECG is assigned a

10

random short-address between 0 and 63. You can now identify the randomly
ordered ECGs/lamps by selecting a respective operation (on/off/blinking) in the
ETS. Use drag-and-drop to pull an ECG into the ECG position previously set in the
ETS. The random order is thus 'dissolved' and the installation is now well­structured.

When you download the DALI configuration, the configured data is downloaded onto
the ECGs and if applicable the short-addresses are amended in line with the pre­configuration. Once you have programmed all DALI data, load the actual ETS
application onto the gateway.

For a detailed description of the ETS commissioning interface, please see chapter

7.

5. Display and push button control

You can commission the connected DALI segment and set and change DALI
functions via the three pushbuttons (MOVE, Set/Prg, ESC) and the 2x12 character
display on the front of the device. The user concept is menu-based. Depending on
the menu position, you can select two sub-levels. The current menu position is
shown on the display. To navigate within the menu, press the pushbuttons briefly.
Use the Move button to select the next menu item on the same level. Use the
Prg/Set button to go to the next lower level. Press the ESC button to leave a level
and return to the next higher level.

Main menu– Level 1

The main menu (Level 1) has the following structure:

The product name and rmware version are displayed. The sub-menu
can be used to set the display language.

The sub-menu displays the IP address set in the ETS or assigned
by he DHCP server.t

When a DALI segment is newly the sub-menu to resetinstalled, use
the connected DALI devices and automaticallysearch for ECGs.

Use the sub-menu to start the automatic search process and possibly
adjust the configuration following a post-installation of DALI ECGs.

Use the sub-menu to active the ECG quick exchange function and
possibly program and integrate individually replaced ECGs into the
system.

POST
INSTALLATION

ECG EASY
REPLACEMENT

NETWORK
IP ADDRESS

DALI CONTROL

- V1.2

NEW
INSTALLATION

11

Use the sub-menu to identify ECGs and assign them to DALI groups.

Use the sub-menu to assigngroups to DALIscenes

Use the sub-menu to switch both the whole installation (broadcast) and
individual channels for test purposes.

GROUP
ASSIGNMENT

SCENE
ASSIGNMENT

GROUP
TEST

Use the sub-menu to test individual scenes.

Use the sub-menu to load any existing system faults.

Use the sub-menu to start the burn-in mode for ECGs and to re-set
operating hours.

Use the sub-menu to activate the converter inhibit mode in the
installation phase.

MAINTANANCE
ECG/LAMP

CONVERTER
INHIBIT MODE

TEST
SCENES

SYSTEM
TEST

To perform a function or change a configuration within a sub-menu, go to the
respective position and change into programming mode. To change into
programming mode, hold the Prg/Set button for more than 2 seconds. Once the
function is in programming mode, a symbol appears in the display. If the
programming mode is active, use the Move button to change a parameter or setting.
Briefly press the Prg/Set button again to complete the process and save the set
parameter or activate the function.

Sub-menu DALI CONTROL – Level 2

The currently set display language is shown. Hold the Prg/Set button to

change into programming mode. Use the MOVE button to choose from
one of the following languages: GERMAN, ENGLISH, FRENCH,
SPANISH, ITALIAN, DUTCH, SWEDISH, DANISH. Briefly press the
Prg/Set button again to save the configuration. The display now works
in the selected language.

Briey press the Prg/Set button to change from the main menu DALI
CONTROL to the sub-menu LANGUAGE.

DALI CONTROL

- V1.2

LANGUAGE
GERMAN

12

Briefly press the Prg/Set button to change from the main menu IP
ADDRESS to the sub-menu.

Briefly press the Prg/Set button to change from the main menu NEW

INSTALLATION to the sub-menu SEARCH ECGs via PROG-MODE.

The sub-menu displays the IP address currently set in the ETS or
assigned by the DHCP-Server.

Hold the Prg/Set button to change into programming mode. Briefly
press the Prg/Set-button again to start the initialisation and search
process. First, all ECGs connected to the DALI segment are
automatically reset and any previously set parameters and group
assignments are deleted. The device then searches for the connected
ECGs via their random long address. The ECGs are automatically
recognised in ascending order. Depending on the number of connected
ECGs the search process may take a few minutes. Once the process is
complete, the number of ECGs found is shown on the display. Press
the ESC button (or wait for about 30 seconds) to return to the level
above.

Sub-menu NETWORK IP_ADDRESS – Level 2 and 3

Sub-menu NEW INSTALLATION – Level 2

NETWORK

NEW­INSTALLATION

DHCP: 192.

168.010.134

SEARCH ECGs
via PROG
MODE

FOUND
ECGs: 47

IP ADDRESS

Briefly press the Prg/Set button to change from the main menu POST­INSTALLATION to the sub-menu SEARCH ECGs via PROG-MODE.

Hold the Prg/Set button to change into programming mode. Briefly
press the Prg/Set-button again to start the verification and search
process. The device searches for the connected ECGs via their long
address and automatically compares them to the previous
configuration

If ECGs have been removed from the DALI segment, the entries are
deleted from the device. The number of deleted devices is displayed
during the verification process.

After that, the DALI segment is searched for newly installed devices.
Newly added ECGs are automatically reset and any previously
programmed parameters and group assignments are deleted.
Depending on the number of connected ECGs the search process may
take a few minutes. During the search process, the number of newly
found devices is shown on the display.

Sub-menu POST-INSTALLATION – Level 2

POST
INSTALLATION

SEARCH ECGs
via PROG-MODE

DELETED
ECGs: 3

NEW
ECGs: 1

13

Once the whole process (verification and search) is complete, the
display shows both the deleted and the newly found ECGs (deleted
devices / new devices from left to right, see picture on the left). Press
the ESC button (or wait for about 30 seconds) to return to the level
above.

Briefly press the Prg/Set button to change from the main menu ECG
QUICK EXCHANGE to the sub-menu SEARCH ECGs via PROG­MODE.

Briefly press the Prg/Set button to change from the main menu GROUP

ASSIGNMENT to the sub-menu.
Within this menu the individual ECGS that were found during the

search process can be assigned to 16 DALI groups and previous
assignments can be modified.

Briefly press the MOVE button to run through the different ECGs. The
number of the selected ECG is shown in the first display line. As long
as the ECG is selected, the connected lamp is flashing. The
programmer can thereby determine which lamp is assigned to the
number.

If the selected device is a non-switchable converter for emergency
lights, the selection sets the device into function test mode and the
display shows the word CONV. For identification purposes, the
function LED on the converter flashes during the test (see user manual
for the converter).

Hold the Prg/Set button to change into programming mode. Briefly

press the Prg/Set-button again to start the quick exchange The.
device first checks if one or several ECGs in the system were faulty. It
then automatically looks for newly connected ECGs in the segment.
The quick exchange is only possible if just one ECG in the segment
was faulty and one new ECG is found. If the process is successful, the
number of the replaced ECG is shown. If the search process cannot be
completed because the required conditions are not met, an error code
appears in the display.The error codes have the following meaning:

Error Type 7: No ECG failure
Error Type 8: More than one ECG failure
Error Type 9: No new ECG can be found
Error Type 10: ECG has wrong device type
Error Type 11: More than one new ECG

Press the ESC button (or wait for about 30 seconds) to return to the
level above.

Sub-menu ECG QUICK EXCHANGE – Level 2

Sub-menu GROUPASSIGNMENT – Level 2 and 3

DEL./NEW
ECGs: 3/1

ECG QUICK
EXCHANGE

GROUP
ASSIGNMENT

ECG No.: 12
GROUP: --

CONV. No.: 13
GROUP: --

SEARCH ECGs
via PROG-MODE

ECG 04
REPLACED

ERROR
TYPE 07

14

Hold the Prg/Set button to change into programming mode. Briefly
press the MOVE button again to select the group that you want to
assign the ECG to. If the group is selected, briefly press the Prg/Set
button to confirm and save the setting. You must repeat this process
once for every ECG during the initial installation. Attention: non­switchable converters for emergency lights cannot be assigned to a
group.

Press the ESC button (or wait for about 30 seconds) to return to the

level above.

Briefly press the Prg/Set button to change from the main menu SCENE
ASSIGNMENT to the sub-menu. Within the menu the DALI groups can
be assigned to up to 16 possible scenes. Individually controlled ECGs
cannot be assigned via the display. To assign individual ECGs, you
must use the website.

Briefly press the Prg/Set button to change from the main menu GROUP

TEST to the sub-menu. Within the menu, groups can be switched
either individually or all together (ALL GROUPS TEST) to test the
installation.

Briefly press the MOVE button to run through the individual scenes.
The number of the selected scene is shown in the first display line.
Behind the scene number, different characters show which of the 16
groups are assigned to the scene. An X means that a group is
assigned to the scene. A – means the group is not assigned to the
scene. The four characters directly behind the scene number in the
first display line represent groups 1 - 4 (from left to right). The 12
characters in the second display line represent groups 5 – 16 (from left
to right).

Hold the Prg/Set button to change into programming mode. A flashing

cursor on the first X means that group 1 is selected. By briefly pressing

the Move button you can toggle between X and – symbols to choose

whether you would like to assign the group to the scene. Briefly press

the Prg/Set-button to move the cursor to the next group. Once you

have run through all 16 groups, the setting is saved and used during

further scene programming. After you have pressed the Prg/Set button

a final time, the display automatically returns to the level above. Press

the ESC button to return to the level above without saving the changes

you have made.

Sub-menu SCENE ASSIGNMENT – Level 2 and 3

Sub-menu GROUP TEST – Level 2 and 3

ECG No.: 12
GROUP: 1

SCENE
ASSIGNMENT

GROUP
TEST

SCENE01 XXXX
XXXXXXXXXXXX

SCENE03 ---­XXXX------XX

15

Briefly press the MOVE button to run through the individual groups.

The number of the selected group is shown in the first display line.

Hold the Prg/Set button to change into programming mode. Briefly
press the Move button to select whether you would like to switch the
group on or off. Briefly press the Prg/Set button to execute the selected
command. Press the ESC button (or wait for about 30 seconds) to
return to the level above.

GROUP: 6
TEST

GROUP: 6

->off

Briefly press the Prg/Set button to change from the main menu SCENE
TEST to the sub-menu. Within the menu you can invoke all scenes for
test purposes or program newly set light scenarios into the scene.

Briefly press the Prg/Set button to change from the main menu
SYSTEM TEST to the sub-menu. Within the menu you can check for
any potential faults.

If there has been a DALI short-circuit, no further faults can be recognised. For

all other fault types, several faults can be recognised at the same time. Within
the menu you can toggle between the different faults by briefly pressing the
Move button. The number of the ECG is displayed for both lamp and ECG
faults. This means that a fault can be easily localised. Press the ESC button
(or wait for about 30 seconds) to return to the level above.

If there is no fault, this is shown in the display. The following faults can

be recognised by the system. They are shown in the display and also

simultaneously set off the red error LED:

● DALI short-circuit

● Lamp fault with the lamp or ECG number being displaye

●

ECG fault with the ECG number being displayed

● No KNX bus

Briefly press the MOVE button to run through the individual scenes. The
number of the selected scene is shown in the first display line.

Hold the Prg/Set button to change into programming mode. Briefly
press the Move button to choose whether you would like to invoke or
save a scene. Briefly press the Prg/Set-Taste button to execute the
selected command and either invoke or save the scene. Press the ESC
button (or wait for about 30 seconds) to return to the level above.

Sub-menu SCENE TEST – Level 2 and 3

Sub-menu SYSTEM TEST – Level 2 and 3

SCENE
TEST

SYSTEM
TEST

LAMP 17
Fault

DALI
No fault

ECG 34
Fault

DALI
Fault

KNX
No Fault

SCENE: 2
TEST

SCENE: 2

->invoke

16

Briefly press the Prg/Set button to change from the main menu
MAINTENANCE ECG/LAMP to the sub-menu. Within the menu you
can start the burn-in of a lamp and reset the reader for its operating
hours.

Briefly press the Prg/Set button to change from the main menu
CONVERTER INHIBIT MODE to the sub-menu. Within the menu you
can turn on the Inhibit Mode for all connected self-contained battery
emergency lamps.

In addition to the pushbuttons, you can also easily commission the DALI via the
integrated web server. For this purpose connect the KDA-64 directly to the IP
network. An RJ-45 socket is located above the KNX bus connector at the bottom
left-hand side of the device.

If the mains power supply is turned off within 15 minutes from
activating the Inhibit Mode, the lights do not change into emergency
mode but remain switched off. Particularly during the initialisation
phase of a building this operating mode may be required to prevent the
emergency lights from being turned on constantly.

Hold the Prg/Set button to change into programming mode. Briefly
press the Prg/Set button again to activate the Inhibit Mode.

Press the ESC button (or wait for about 30 seconds) to return to the
level above.

Briefly press the MOVE button to run through the individual ECGs. The

number of the selected ECG is shown in the first display line.

Line 2 shows the number of operating hours since the last reset / burn­in.

Hold the Prg/Set button to change into programming mode. Briefly
press the Move button to toggle between the functions BURN-IN,
RESET, BURN-IN/RESET. Briefly press the Prg/Set button to execute
the selected command Press the ESC button (or wait for about 30.
seconds) to return to the level above.

Sub-menu MAINTENANCE ECG/LAMP– Level 2 and 3

Sub-menu CONVERTER INHIBIT MODE – Level 2

6. Control via web browser

MAINTANANCE
ECG/LAMP

CONVERTER
INHIBIT
MODE

INHIBIT
via PROG-MODE

CONVERTER
INHIBIT?

ECG No.: 01
368 h

ECG No.: 01
BURNIN

ECG No.: 01
BURNIN/RES.

17

Use a standard patch cable to connect the device to a switch, hub or router of the IP
network. You can also use a WLAN access point as network coupler. This means you
can commission the DALI via a portable note book, tablet PC or mobile phone.

Once the network is physically connected, you need to assign an IP address to the
KDA-64 to enable access via the web browser. By default, KDA-64 with an IP
interface are set to DHCPaddress assignment.

If there is a DHCP server in the network the device automatically receives an IP
address after initialisation. This address is shown on the device display (see
above).

If no DHCP service is available or if you would rather use a fixed IP address, you
must set the address either via ETS or the device display. You may also need to
configure the sub-net mask and standard gateway (for direct access via the
Internet). Those two parameters can only be configured in the ETS. See an example
in below. If DCHP address of KDA-64 is 192.168.10.134, set default gateway to be

192.168.10.134. Set IP address as 192.168.10.133. Subnet mask will be assigned
automatically.

18

Once the IP address has been assigned, load the device website via any web
browser (e.g. Microsoft Internet Explorer, Mozilla Firefox, Apple Safari). Simply
enter the correct IP address (URL) in the browser.

Please remember that the complete URL consists of the IP address and the
prefix http:// To load a page enter, for example http://192.168.10.134.

The following web site appears:

Use the log-in-page to assign either 'User' or 'Administrator' rights to a user. User
rights mean that the website functions are restricted and configuration commands
are disabled. Use this login if you would like to use the website only for visualisation
and operational purposes. To commission the DALI via the website administrator,
rights are required. The images and descriptions below are all based on the

19

administrator display. Different passwords for user and administrator can be set in
the ETS. The default setting for both users is '0'.

Log in as administrator to access the following configuration website:

The configuration page is divided into different sections. The section at the top of
the page contains the configuration buttons that are required for the commissioning.
(Some of these buttons are only visible if you log in as administrator). The fields
underneath the configuration buttons are for the 16 group and 64 ECG functions.
The bottom section contains the information and status area. The three tabs in the
footer are used to change from general configuration to scene configuration and
effect configuration.

All operable buttons work with tool tips. This means a description of the function
appears if the cursor hovers over the button.

20

6.1 Configuration buttons

The icons in the website header are used for the different commissioning functions.
They have the following meaning:

This function refreshes the website content. On principle, the website is static. This
means that the details on the page are only updated when the site is first loaded.
Any faults or changes that are not made on the website itself, such as a light status
adjustment via a KNX telegram are not automatically displayed.

Press this button to start a new installation (reset and teach-in process) of the
connected DALI segment. Attention: During a new installation any previously

existing configurations of the DALI segment are deleted.

Refresh

New Installation

Press this button to start a post-installation within the DALI segment. Any ECGs that
no longer exist are deleted during the post-installation process. At the same time
new devices are added.

Press this button to start an ECG quick exchange within the DALI segment. The
quick exchange is only possible when a single faulty ECG is replaced by a new one.

Press this button to display the device status of the gateway in the information and
status area at the bottom of the page. Click on a group or ECG field to display the
status information of the selected ECG or group.

Use these functions to simultaneously switch all ECG lights /lamps in the DALI
segment off or on or set them to blink-mode via a DALI Broadcast telegram.

Post-installation

ECG Quick Exchange

Device status

Broadcast ON Broadcast OFF Broadcast Blink

21

22

Use this button to assign an ECG to a group. First select the button. Then click on
the group. To complete the process click on the ECG you want to assign to the
group. If the ECG was previously assigned to a group, the previous assignment is
automatically removed.

Assign a group

Remove assignment

No selection First button selected

6.2 Control buttons

There are further control buttons above the ECG field. These are used to perform
ECG or group specific operations. To carry out one of the operations, you must­select the operation first and then click on the group or ECG concerned. The
selected function appears in a white frame. Press the button again to cancel the
selection.

The individual buttons have the following meaning:

Use this button to remove the assignment of an ECG. Select the button first. Then
click on the ECG. If the ECG was assigned to a group, the group assignment is
deleted. If the ECG was marked for individual control, it is now marked as 'not in
use'.

23

With this button an ECG is marked for individual control. ECGs that were found
during the search process first appear with a question mark. This means that they
are considered to be 'not in use'. If you want to enable an ECG for individual
control, select the button and then click on the ECG concerned The ECG is marked.
with the letter 'S' (Single) and is now in use.

Mark ECGs for individual control

Use this button to set an individual ECG or a group to blink-mode. To carry out this
function, select the button first. If you now press an ECG or group field, the
corresponding ECGs/lamps start blinking. The blink-mode is used for identification
purposes during the DALI commissioning process. If you press the same ECG or
group field again, the blinking stops. If you press another ECG or group field with the
button still selected, this element starts blinking and the previously blinking lamp is
turned off.

ECG / group blink-mode

24

Use this button to switch the value of a group on or off. First select the button. Then
click on a group field to toggle between the light values of all lamps assigned to the
group. The same process is used for ECG fields.

Use this button to swap the position and thereby the short address of two different
ECGs. First select the button. Now click on two ECG fields one after the other to
physically swap their short addresses and adjust their position in the list. This
function is required to sort the random ECGS into a specific order after a new
installation. You should only use this function directly after a new installation.

Later use should be avoided as the parameters set in the ETS are not swapped
in line with the addresses.

Swap ECG short addresses

Toggle light value

25

6.3 ECG f ields

The ECG and group entries on the website mean that the user can see the complete
function and failure status of a connected DALI segment at a glance. The ECG
fields are numbered from 1 – 64. The number is shown in the bottom left-hand corner
of the field and corresponds to the ECG short address within the DALI segment. If an
ECG is found during the search process (new and post-installation), a lamp or
battery icon is inserted in the field. The battery icon symbolises an ECG for self­contained battery emergency lights (device type 1). All other device types (without
battery) are shown with a lamp symbol. If in the ETS an ECG is configured as
emergency luminaire with central battery, a separate icon is displayed. The
following icons are available:

ECG

ECG for self-contained battery emergency lamp non-switchable

ECG for self-contained battery emergency lamp switchable

ECG with central battery supply

ICON light grey => Lamp switched off

ICON yellow => Lamp switched on

ICON red => Lamp failure

Red background => ECG failure

The value and failure status of an ECG is symbolised by different icon and background
colours.

26

The assignment of an ECG is also shown in the field. Newly found devices are
marked as 'not assigned' via a '?' symbol above the icon. When an ECG is assigned
to a group, the group number replaces the '?' symbol. If an ECG is used for
individual control, it is marked with the letter 'S' (Single).

6.4 Group fields

As for the ECG fields, the group fields show the status of a group. However, the
display is limited to the switch status. No failure status is graphically displayed.

ECG not i n use

ECG in use for individual control

ECG with group assignment (e.g. group 3)

27

If you switch a group or ECG via the website, its status is automatically updated and
displayed on the site. However, if the switch command was initiated externally via a
KNX telegram, the status is not automatically updated. To display the correct
status, press the refresh button or re-load the web page.

6.5 Information and status fields

The bottom section of the configuration website shows status information for the
device as a whole or for a selected group or a selected ECG.

When the website is first loaded, the status information always applies to the whole
device giving you the opportunity to see the number of connected lamps, ECGs and
converters, as well as faults and fault rate at a glance.

ICON light grey => group switched off

ICON yellow => group switched on

The green colour means that no fault has occurred. Otherwise the colour changes to
red.

This information can be displayed at any time by pressing the device status button in
the configuration bar at the top of the site.

To display the status information of a group, click on one of the 16 group fields.

28

In addition to the number of devices and converters and the individual failure types,
the total failure rate is shown. Please remember that the rate is calculated as a
percentage of the total number of ECGs and converters in the group. Use the Name
field to enter a user-friendly name for the group. The maximum number of
characters is 10. Press the -button to confirm your entry. The name is now saved√
on the gateway and loaded into the ETS during the next synchronisation.

To display the status information of an ECG, click on one of the 64 ECG fields.
Choose from one of the following options: General, Run Hours, Burn in and Test.-

Note: In default setting in the ETS burn-in and operating-hour calculation is
disabled. You have to set the correct parameters in ETS and download the
application. After the download the pages in the web interface are available. The
„test“ page is only available, when the connected ballast is a DALI device type 1
(self contained emergency ballast- with battery). Only those ballasts support the
emergency test functions.

Use the name field on the General page to enter a user-friendly name for the ECG.
The maximum number of characters is again 10. Press the -button to confirm your√
entry. The name is now saved on the gateway and loaded into the ETS during the
next synchronisation.

An ICON appears behind the word Alarm if a fault or alarm has occurred. The
meaning of the icons is as follows:

29

Lamp failure

ECG failure

Converter failure

Life cycle exceeded

Permanent mode

Panic mode

Central battery test mode

Burn-in mode

An ICON appears behind the word Mode if the ECG is not in normal mode. The
meaning of the icons is as follows:

Click on the Run Hours tab in the header to see the accumulated operating hours of
a lamp since its last reset as well as the maximum life span that was configured in
the ETS. Use the button on the right to reset the counter to 0.

Click on the Burn-in tab in the header to start and stop the burn-in mode for the
selected ECG.

30

The maximum burn-in time that was configured in the ETS and the already
completed burn-in time are also displayed.

This display shows the type of test, test result and date and time of the last test. The
status bar shows the failure flags. A green bar means that the test was positive. A
red bar signals a negative test result.

You can use the buttons on this page to manually start a test (Execute Test). The
icons underneath have the following meaning:

Please remember that the website is static and is not automatically updated after
the test has finished. If you would like to display the result of a manually activated
test, please press the 'Update test result' button first.

Battery Test

Functional Test

Long Duration Test

31

7. ETS special and commissioning functions

As previously described in chapter 4, you can choose eiher type A 'Normal mode' or
type B 'Extended mode' for the DALI commissioning. Depending on the mode you
choose, different special functions and pages are available in the ETS.

7.1 Special functions in 'Normal mode'

7.1.1 Synchronisation with the connected DALI segment

When you first load the parameter page, the parameters and groups for all possible
64 ECGs and 16 groups are displayed. In ETS mode A it is possible to simplify the
commissioning and to bring the application in line with the real conditions of the
connected DALI segment. To do so, you need to synchronise the application with the
installation first.

Start the synchronisation via the sync button in the bottom right-hand corner of the
main window. Depending on the size of the installation the synchronisation may take
a few seconds. A bar at the bottom of the page shows how far the synchronisation
has progressed. When the synchronisation is complete, only the objects and
parameters of those ECGs that are physically connected to the device are shown.

32

In addition, the device types and, if applicable, the group asignments are also
automatically set.

If during the synchronisation a device type is found that does not match with the
current settings in the ETS, a warning message appears. Please acknowledge the
message by pressing yes or no.

By default the synchronisation of the ETS is performed via the KNX network. If the
gateway is already correctly integrated into the IP network and a corresponding IP
address has been assigned, the synchronisation can also be performed via
Ethernet. In this case, all you need to do is enter the correct IP address of the device
into the tool bar at the top of the window and tick the check-box in front of the bar.
Alternatively, you can press the Read IP Address button to set the IP address of the
selected device without manual entry.

The synchronisation compares the application to the data of the connected DALI
segment. This means that you should always synchronise when you change

the system structure or expand the system.

7.1.2 User-friendly names for ECGs and groups

To make the configuration as easy as possible for the user it makes sense to,
choose user-friendly names for ECGs and groups. Any names need to be assigned
on the website in ETS Mode A directly during the identification. Please remember to
press the confirm button next to the entry field after entering a name.

33

Use the 'Load Description' command in the Tools menu to load the names directly
into the ETS. The names are shown in brackets next to the corresponding device.

34

As loading the names via KNX can take quite some time, you should use the
Ethernet connection for this process. Before starting the process, please make sure
you set the right IPaddress and tick the check-box in front of the address.

7.2 Special functions in 'Extended Mode'

If you select 'extended Mode' (Mode B) for the DALI commissioning (see chapter 4),
an additional menu appears underneath the main menu bar with the entries
'Parameter' 'Commissioning', 'Scenes' and 'Effects',

Use the menu item 'Parameter' to set the ETS parameters in the same way as in
mode A. However, please remember that in mode B all parameters are visible
because the parameter settings can be performed independently of the actual
system Simplifying the parameters and objects by synchronising with the system is.
not possible in this mode.

The menu item 'Commissioning' is described in more detail in the next chapter. For a
description of menu items 'Scenes' and 'Effects', please see chapter 11.

7.2.1 Preparing and planning the DALI commissioning in 'Extended Mode'

In Mode B, the menu item 'Commissioning' opens an additional page which is not
available in 'normal mode'. This page is used both to plan the installation in advance
of the commissioning and to perform the actual DALI commissioning later on
(identification and assignment of ECGs).

35

The structure of the commissioning page is as follows: The group configuration is
displayed on the left-hand side in a tree structure The area in the middle shows the.
ECG configuration and names in a table format. On the right hand side is a list of all
devices found in the system which have not yet been identified. During the planning,
stage this part is empty as the ETS is not yet connected to the system.

To start with you should plan and name the ECGs. Use the description field in the
ECG configuration to enter a name (light number, room number, etc.)

The maximum number of characters available for names in the ETS plug-in is 30.
Whilst, in principle, the names are also transferred to the device website, it is
important to remember that the website will display no more than the first ten
characters of the name entered in the plug-in.

If you confirm your entry with the return button, the cursor automatically jumps to the
next ECG field. This makes the naming process easy and secure.

Once you have planned the ECGS, you should assign the groups. There are two
ways to assign groups via drag-and-drop:

1.) Use the mouse to select an ECG in the ECG configuration field in the middle
and drag it to the left dropping it above the required group in the group tree.

2.) Use the mouse to select an ECG from the group directory's top category 'not
assigned' and move it down the directory dropping it above the required group.

36

Once an ECG has been assigned to a group via drag and drop, the group number is
automatically displayed in the 'group number' field of the ECG configuration table.
You can enter a user-friendly name for the group in the 'group description' field.
ECG and group names are automatically shown in the group configuration directory
(displayed in brackets) as well as in the description of the ETS communications
objects. Having user-friendly names makes linking the group addresses with the
communications objects much easier for the system integrator.

As soon as an ECG has been assigned to a group, it is no longer available for
individual control. The parameters and communication objects are adjusted
accordingly following the group assignment. ECGs that have not been assigned to a
group are automatically regarded as ECGs for individual control.

Please see chapter 11 for the planning and setting of scenes and effects.

7.2.2 DALI commissioning in 'Extended Mode'

Once the planning, parameter setting and linking of group addresses have all been
completed the DALI segment can be commissioned. To do so, please connect the
commissioning PC with the ETS to the KNX system via an interface (RS-232, USB or
IP). Once the connection is active, you need to program the physical address of the
gateway. The communication between the plug-in and the gateway is based on the
physical address (or possibly on the IP address, see below).

Use the 'commissioning' page and the 'tools' menu to start the teach-in process of
the connected DALI segment.

37

Please remember that the selection shown above is only visible in the 'Tools' menu if
you have selected the 'commissioning' page. The elements displayed always
depend on the setting selected in the menu bar.

During the teach-in process all ECGs are automatically recognised and each ECG is
assigned a short address from 0 - 63. Depending on the size of the connected DALI
segment the process can take up to 3 minutes.

A bar in the bottom right hand corner indicates how far this process has progressed.
The number of ECGs that have so far been found is also shown (in brackets).

Once the teach-in process is complete, all ECGs that have been found are displayed
in the list of non-identified devices on the right-hand side.

You can now identify the devices by switching the corresponding lamp on or off. If
you select an ECG and press the right mouse button, a context menu appears from
which you can select the required function.

38

Alternatively, you can also tick the box 'blink '. In this case, the blink mode starts by
itself when a device is selected. The context menu is also available at group and
gateway level. During the identification process it might be useful to switch certain
groups or all connected lamps on or off. If you select the main item 'group
configuration', you can use the right mouse button to send broadcast commands for
on, off and blinking.

Once an ECG has been identified, you can drag and drop it onto the previously
planned element in the ECG configuration table.

Once an ECG has been dragged into the ECG configuration table, it disappears
from the list of non-identified ECGs. The 'PLAN' flag in the configuration table
shows that the ECG has been assigned to the planned element.

If an ECG has been wrongly assigned, it can be moved back to the list of non­identified devices using the same drag& drop mechanism.

After the ECG has been moved back, the element in the configuration table is empty
(Flag: 'PLAN (E)' Empty) and the ECG re-appears in the list of non-identified
devices from where it can now be moved to a different element if required.

Please remember that at this point all operations that have been performed are only
displayed in the work space. They are not immediately loaded onto the DALI
gateway. To start the process of downloading the settings onto the gateway and the
ECGs, you must press the 'Download DALI' button. The download can take up to 2
minutes. The progress bar informs about the current status.

Once the download is complete, all previously planned ECGs are programmed in
the real system with the DALI configuration. The respective devices are marked with
an 'OK' flag in the ECG configuration table.

39

Non-identified devices remain in the list on the right-hand side.

Attention: Please remember that the download on the 'commissioning page'
only programmes the DALI configuration data onto the gateway and ECGs.
Following the DALI identification and commissioning the actual ETS
application with parameter settings and group addresses still has to be
downloaded on to the device. After leaving the parameter page, this is done via

the usual ETS download process.

7.2.3 ECG and lamp faults during DALI commissioning in 'Extended Mode'

During the commissioning lamps/ECGs are identified visually (ON, OFF, blinking). It
is therefore crucial that all lamps and ECGS operate correctly. If the gateway
identifies a lamp or ECG fault during the installation process, the ECG concerned is
highlighted in a different colour. A red flag indicates an ECG fault and a yellow flag a
lamp fault.

40

Faults are displayed both for non-identified devices (right table) and for ECGs that
have already been assigned (middle table). As the table view is not automatically
updated and as it may take a few minutes for the DALI gateway to recognise a fault,
we recommend that you press the 'Sync' button a short while after the installation.
This ensures that the displayed status corresponds to the actual status and any
faults that may have been detected in the meantime are displayed correctly.

Attention: If an ECG fault already exists during the search process of the initial
installation, the device may not be detected at all. This means that the number of
ECGs found does not correspond to the number that was expected. ECG faults are
only displayed in the manner described above if the ECG concerned has been
previously programmed and is known to the gateway.

7.2.4 Using dummy ECGs in 'Extended Mode'

There may be cases in which a DALI installation or a DALI segment needs to be
commissioned even if not all of the planned lights are yet physically present (e.g. if a
room is not yet finished or a light has not been delivered). During the teach-in
process only the actually existing devices are detected and entered into the list of
non-identified devices. This means that only those devices can be moved into the
configuration table and commissioned as a real device. Entries for devices that are
planned but do not yet exist remain empty in the configuration table. These devices
can be programmed, identified and assigned later on during a post-installation (see
below) once the whole installation is complete.

As long as an entry remains empty, the gateway assumes that no ECG exists and
does not generate an error message. However, it may be desirable that an error
message for a planned device is generated, even if the device is not yet present (for
example to visualise an incomplete installation).

The plug-in offers the possibility to add dummy ECGs to the list of non-identified
devices. This special option is not set up by default. To use this option, please go to
'Tools' 'Options' to activate it.

41

Once it has been activated, an additional 'Dummy+'button appears in the parameter
window.

Use this button to add dummy ECGs to the list of non-identified ECGs.
Dummy ECGs are marked with a symbol and can be dragged into the ECG

configuration in the same way as normal ECGs. Once the DALI data has been
downloaded, the gateway assumes that an ECG exists and therefore presents an
ECG fault in the visualisation and the respective communication object.

The dummy ECGs are only used as a temporary solution in an unfinished
installation. The 'post-installation' that is required once the whole installation is
complete, deletes all dummy entries from both the ECG configuration table and from
the list of non-identified devices.

7.3 General extra functions in the ETS ‘

The functions described in the following chapters can be used both in 'Normal Mode'
and in 'Extended Mode'.

7.3.1 Using IP for plug-in communication

By default, the plug-in communicates with the DALI gateways via the KNX-Bus.
However, if the gateway is integrated into an IP network and a correct IP address
has been assigned (DHCP or fixed setting in the ETS) IP communication can also be
used. This increases the speed of loading and communication processes greatly.

42

Please remember that when IP communication is enabled (by ticking the box),
the plug-in communicates with the gateway always via the address entered. A
wrong manual entry may lead to a wrong gateway being contacted. Therefore
please make sure that the IP address is correct.

If the IP communications box is ticked but an IP connection is not possible (wrong IP
address, no network connection), the plug-in will still try to make the connection via
IP. However, it recognises by itself that this is not possible and automatically
changes to KNX communication.

IP communication can be used both in 'Normal Mode' and 'Extended Mode'.

7.3.2 Parameter templates

The KDA-64 gives you the possibility to create your own parameter templates
thereby making the time-consuming parameter setting for individual groups or
ECGs much easier. Parameter templates can be generated for all parameters of the
entire gateway and for individual ECGs and groups. Once you have completely set
the parameters for a standard ECG, simply press the Export function in the Files
menu or click on the right mouse button to export them as an xml file.

If you would like another ECG to have the same parameter properties, simply select
the ECG and import the exported file into the new ECG. The file serves as a template
for other ECGs. You can also create templates at group level or for 'General
Properties'. Creating templates for all ECG and group types and using this template
library makes the configuration, especially in large installations, significantly easier.

If you would like to re-set individual ECG or group parameters or even a whole
gateway to their original status, please use the files that have been provided with
the product:

43

● default_device.xml

● default_ecg.xml

● default_group.xml

7.3.3 DALI configuration data back-up

The configuration data and parameters set in the ETS are automatically saved in the
ETS database after each change. They can be easily downloaded onto a new device
at any time. However, the DALI configuration data, such as the DALI long address,
is not part of the normal ETS application. To back-up the DALI configuration data,
please use the back-up function in the Files menu.

The backup function exports the current real configuration from the gateway and
saves it as an xml file. Attention: The DALI configuration data in the ETS is also

updated during a back-up. Any changes that were made in the ETS but that
have not yet been downloaded onto the gateway (planning only), are therefore

If you need to exchange a device, you can load the backed-up data onto a new
device via Restore. Backup – Restore gives you the opportunity of a simple device
exchange without the time-consuming post-installation. We therefore strongly
recommend that you create a back-up and save the data after completing the
parameter settings.

8. DALI maintenance and expansion

8.1. Quick exchange of individual ECGs

When a DALI segment is commissioned the short address, group assignment (if,
applicable) and other configuration data are programmed onto the ECG's internal
memory. If you had to replace an ECG because of a fault, you would normally need
to program this data onto the new device.The KDA-64, however, offers a function
that makes it possible to quickly and easily replace individual ECGs. You can start
the “ECG quick exchange“ function either on the device itself (pushbuttons, display)
or via the web browser if you log in as administrator (see above). The gateway first
checks if any of the configured ECGs that are known to it have been reported as
faulty. Then the segment is searched for new, unknown devices. If a new device is
found, all configuration details of the old ECG are automatically programmed onto

44

the new one and the installation is immediately ready for operation.
However, the ECG quick exchange only works if just one ECG within a segment is

faulty and replaced by a new one. If several devices are faulty, the ECGs have to be
identified and you must use the post-installation function. Please also remember
that the quick exchange is only possible for devices of the same type. You cannot,
for example, replace an ECG for self-contained battery emergency lamps with a
device for LEDs.

If a quick exchange is not possible, the gateway terminates the process with an
error code. The different error codes have the following meaning:

Error type 7: No ECG failure
Error type 8: More than one ECG failure
Error type 9: No new ECG can be found
Error type 10: ECG has wrong device type
Error type 11: More than one new ECG

8.2 Extending the existing system – post-installation

If you would like to enlarge an already commissioned DALI segment with new ECGs
or would like to replace several faulty ones, please use the „post-installation“
function. You can carry out the post-installation both on the device (pushbuttons,
display) and via the web browser if you log in as administrator (see above).

If you use the ETS in 'Extended Mode' (Mode B), you can also load the post­installation in the ETS via the menu 'Tool' 'post-installation'.

When you start the installation, the gateway first checks if all previously configured
ECGs are still available in the segment. ECGs that no longer exist or cannot be
found are deleted from the gateway's internal memory. Then the segment is
searched for new ECGs. Newly found devices are inserted into any existing gaps or
added on at the end. (Attention: Please remember that the maximum number of

ECGs within a segment is 64!)

As the position (short address) of a newly found device is allocated randomly, you
need to identify the lights and if required assign them to groups.

If you are using the ETS in 'Normal Mode', you need to re-synchronise the ETS so
that communication objects and parameters for the newly added ECGs are shown
and the configuration can be completed.

However, synchronising the ETS is only necessary if the structure of the segment
has been changed by the post-installation process (enlargement of the system or
different device types). If the purpose of the post-installation was merely re­configuration after an ECG replacement, synchronisation is not required.

In the ETS setting 'Extended Mode' all parameters and objects are visible. This
means that you only need to identify and assign the devices that were newly found
during the post-installation followed by a DALI download and possibly an ETS
application download.

45

9. Different operating modes

9.1 Normal mode

In normal mode, ECGs can be dimmed and switched without restrictions both via
individual and group control. The control of each ECG and each group is based on
three communication objects (switching, dimming, value setting).

Please remember that ECGs, once they have been assigned to a group, are no
longer available for individual control.An ECG can only be assigned to a single DALI
group. The KDA-64 does not support multi-group assignments on DALI level. If such
assignment is required, please use KNX communication objects for this purpose.

At group level an additional enable/disable object is available to disable the control,
via the three communication objects.

Separate status objects inform about the switch and value status both at group and
individual ECG level.

9.2 Permanent mode

If you would like to run an individual ECG or a whole group permanently with a
certain light value (e.g. a permanently lit corridor or workshop) you can choose the,
permanent mode option. The ECG or group are automatically set to the required
value after you program or switch on the gateway. Switch and dim objects remain
hidden. Light status, error and service functions, however, are also available in
permanent mode.

46

Should a device in this mode not be running at the pre-set light level because
of a special operation (e.g. identification process on the device display) or
fault (e.g. ECG was without power when the gateway was started) the light
level is automatically corrected after 60 seconds.

9.3 Staircase mode

The staircase mode is only available for groups. In this mode, the value set via a
switch, dim or value telegram is automatically changed to the switch off value after a
programmable time. The lights can be switched off immediately or in 2 steps (within
a minute) or through dim-down (within a minute).

In staircase mode, each additionally received telegram re-starts the internal timer.
The lights switch off when the timer runs out after the most recently received
telegram.

The staircase mode can be disabled or enabled via an additional object. If the
staircase mode is disabled, the group behaves like in normal mode and does not
automatically switch off. If the mode is disabled whilst the switch-off timer is already
running, the timer stops and the group remains at the currently set value If the mode
is enabled again, the timer starts again from the beginning.

47

9.4 Night-time mode

Night-time mode is available both at group and ECG level. The night time mode­corresponds largely to the staircase mode. The only difference is that the automatic
switch off is dependent on the central night object of the gateway. If the night object­is not set (day), the group behaves as in normal mode. If the object is set (night), the
ECG or group either switches off after a programmable time or it goes into
permanent mode.

9.5 Panic / emergency mode

The panic or emergency mode can be activated via a central object for the whole
gateway. All ECGs/ groups that have been enabled for panic mode, permanently
switch to a programmable panic light value on receipt of the object. They can no
longer be controlled individually. When the panic mode is switched off, the devices
return to the previous light value or the switch on / switch off value and can again be
controlled individually.

9.6 Test mode for central battery emergency luminaires

Through its internal function the KDA-64 supports installations with central battery
emergency luminaires. Any ECG (except for those of the self-contained battery
type) can be configured as an emergency light. You can choose a test time between
15 minutes and 4 hours. If the gateway receives the central battery test object, the
respective lights change to a programmable value for this time period. They can no
longer be switched or dimmed via the corresponding objects. The discharge time
and capacity of the central battery can thereby be tested under pre-defined
conditions.

So that individual ECGs within a group can no longer be switched via group
telegrams or scenes, the group assignment is dissolved for the duration of the test
mode. When the test has finished, groups and scenes are automatically re­programmed onto the ECGs. Should the gateway lose power during the test mode,
the un-programmed devices are marked and automatically programmed on return of
the power supply. The test mode, however, does not continue. It has to be re­started.

When the test mode terminates normally, the devices return to the previous light
value or the switch on / switch off value and can again be controlled individually.

48

9.7 Burn-in mode

For optimum operation and to achieve the quoted life span, many lights require that
a specific burn-in time be adhered to during their first use. During the burn-in phase
lights must not be switched or dimmed but need to run continually at 100% capacity.
This burn-in phase can be carried out automatically with the KDA-64. Each ECG can
be individually set to the burn-in mode via a further object. During the burn-in,
switch and dim telegrams for the device are ignored. This also applies when the
ECG is assigned to a group. So that individual ECGs within a group can no longer be
switched via group telegrams or scenes, the group assignment is dissolved for the
duration of the burn-in mode. When the burn-in has finished, groups and scenes are
automatically re-programmed onto the ECGs. Should the gateway lose power
during burn-in mode, the un-programmed devices are marked and automatically
programmed on return of the power supply. The burn-in mode, however, does not
continue. It has to be re-started. When the burn-in mode finishes normally, the
devices return to the previous light value or the switch on / switch off value and can
again be controlled individually.

The burn-in mode is usually started manually after each light change. This useful
maintenance function can be operated via the device display to ensure that it can be
performed by maintenance personnel independent of the ETS or KNX. Alternatively
a burn-in start is also possible via the integrated web server.

49

9.8 Operating mode hierarchy

Some of the individual operating modes described above have higher functions and
roles for the operation of the system as a whole. A prioritisation or hierarchy of
operating modes is therefore required. The burn-in mode has the highest priority. If
an ECG is in burn-in mode, it cannot be changed into any other mode. The next
hierarchy level is the central battery test mode. If the device is in this mode, it can
only go into burn-in mode but not into any subordinate operating modes. Below the
test mode is the panic/emergency mode. From this mode the device can change to
both the burn-in mode and the test mode. The permanent, normal and night-time
modes have the same priority level at the bottom of the hierarchy.

10. Analysis and service functions

10.1 Recording operating hours

The KDA-64 allows for the operating hours (burning time) of each lamp to be
internally recorded to the second. The value is available externally (communication
objects, web site, display on the device) in hours with the internal value in seconds
always being rounded. (e.g. 7199 seconds 1 h, 7201 seconds 2h) The recording of
operating hours is independent of the dim value. This means any light value > 0%
contributes to an increase in the operating hours. The counter can be re set (when­the light is changed). To reset the counter, the value 0 is written on the
communication object or alternatively you can use the website or the display and
pushbuttons on the device.

A maximum value can be configured for each ECG (light life span), which activates
an alarm object on the KNX bus or an entry on the website. This information can be
used for maintenance purposes.

10.2 Individual fault recognition at ECG level

A major advantage of DALI technology is the individual recognition of light failure or
ECG failure. The KDA-64 supports this function completely and also offers
numerous analytical possibilities.

50

For the analysis, the DaliGateway scans all connected ECGs periodically for ECG,
light and (in the case of self-contained battery lamps) converter failures. The
scanning time can be configured. If the time is 1 second (standard setting), and 64
ECGs are connected, the complete process of scanning for ECG and light failure
takes 128 seconds (1 second per ECG and type of failure). It can therefore take up
to about 2 minutes before a fault that has occurred is recognised For each ECG a.
communication object is available to send the information to the KNX bus (1Bit or 1
Byte object).

In addition, the failure status of all ECGs is displayed clearly on the gateway's
website.

An ECG field with a red background on the website indicates an ECG (or converter)
failure A red lamp symbol indicates a light failure. If you select the respective ECG,.
the individual failure status is available in the status and information section at the

You can also request the failure status of all individual ECGs, converters and lamps
via a special failure status object (object number 20, see communication object
description below).

10.3 Fault analysis at group level

If ECGs and / or converters are merged into groups, numerous group-specific fault
data is available in addition to the (also still available) individual ECG data. For this
purpose three different communication objects are available for each group. In
addition to general information such as whether there is a failure within a group and
of what type, the complete number of faulty devices within the group and the failure
rate can be listed via a communication object. An alarm object is sent when a
certain failure rate is exceeded. A complex object with a summary of the data further
adds to the analysis options.

For details of group-specific communication objects, please see the communication
objects description below.

51

The group information is also displayed on the web site of the integrated web server:

10.4 Fault analysis at device level

Fault analysis objects similar to those at group level are also available at device
level (i.e. for all ECGs connected to the gateway). The failure rate or number of ECG
failures in the whole DALI segment can be made available via communication
objects. Unlike at group level, at device level the percentage and number of failures
can be broken down further according to type of failure. The alarm threshold for the
failure rate can be individually set for ECG, light and converter failure. For further
details regarding the communication objects, please see the communication objects
description below.

As before, the fault information for the entire gateway is displayed on the web site:

52

11. Scenes and effects

11.1 The scenes module

The KDA-64 enables the programming and invoking of up to 16 internal light scenes.
A scene is invoke via a 1Byte scene object.This object can also be used to save
scenes (Bit 7 set). The currently set value is saved as scene value.

In principle, a scene can consist of group and individual ECGs (as long as these
have not been assigned to a group).

To assign a group to a scene or to delete a group from a scene, use the pushbuttons
and display on the device or the website. If you are using the ETS in 'extended
Mode', you can also set and assign scenes via ETS. You cannot assign individual
ECGs to scenes only by using the pushbuttons and display.

By default, the programmed scene is started immediately without dim time. If you
want to dim into a scene, you can set a dim time for each scene. The time can only
be set on the website. Please remember that the entry refers to the dim time from 0
to 100%. If invoking a scene leads to a change from 50% to 100% with a set time of
20 seconds, the dimming process takes only 10 seconds.

Switching an individual group (or ECG) from the scene whilst a scene is already in
the dimming process, only affects the particular group. The other groups continue
the dimming process.

Please remember to use the DALI command for scene addressing only when you
invoke a scene without dimming. Dimmed scenes must be started at DALI level via
short or group addresses. Scenes that have been assigned a large number of
groups or ECGs should therefore be used without dim time to prevent irregular
dimming.

11.1.1 Scene programming via the scene website

For full and easy scene programming, use the website of the server which can be
accessed via the scene tab at the bottom:

53

As before, select the required programming button first and then the group or ECG.
The dim values can only be changed in increments. The increment size varies
according to the logarithmic dimming curve of the DALI ECG.

You may also set the dim time and program a specific name for the selected scene.
Use the programming button to save the set values on the gateway and ECG.

Please remember that the set values are only saved if you press the button. If you
change to another scene without saving, any changes you made are lost.

Use Reload Scenes button to read latest scenes setting. (After click reload scenes
button, it won't show the change immediately. Please go to other tab and then go
back scene tab to renew the page, then you will see the latest scenes setting.)

11.1.2 Scene programming via ETS in 'Extended Mode'

If you are using ETS in 'extended Mode' (Mode B), you can program and assign
scenes in ETS.

On- Off- Up- Down Assign-

Switching Dimming

Program Scene

Reload Scenes

To program a scene, select it first from the scene block at the bottom of the page. (If
the scene has been previously programmed, the corresponding light value
appears).

Once you have selected a scene, you can use the assignment button to add or
remove groups or individual ECGs to and from the scene. Click on the button first
and then on the group or ECG. For already assigned groups or ECGs, the fields are
highlighted in yellow and the dim value is displayed in percentages.

You can only use individual ECGs in scenes if they have not been assigned to a
group.

Use the programming buttons to change the light value. The buttons have the
following meaning:

54

Go to the scenes page and select the required scene from the directory on the left­hand side. Move the groups and individual ECGs which you would like to use for this
scene from the directory on the right-hand side into the field in the middle using
drag-and-drop. Use the value fields to enter the light value for this scene.

A user-friendly name can be added for each scene in the description field
underneath the scenes. If you do not want a scene to start immediately but would
prefer dimming it up to its final value (see below), you can set the dimming time
individually for each scene.

55

Once all scene values have been set and assigned, you need to download the scene
onto the DALI gateway. For this purpose, please press the download button in the
bottom right-hand corner.

In principal you can also use ETS to plan individual scenes 'offline', independently
of the DALI system. The plug-in only has to be connected to the gateway for the
duration of the download.

11.2 The effect module

In addition to light scenes, the KDA-64 also allows for the use of effects. An effect is
a sequence control of light values in different groups or ECGs. The individual light
values can be triggered immediately or dimmed via a dim value. Please remember
that the entry relates to a dim time from 0 to 100% (see scene module above). With
the KDA-64 you can create 16 independent effects. A 1 Byte object is used to start
and stop an effect. To start an effect, set Bit 7 in the object. If the object is received
with Bit 7 being deleted, the effect stops. Altogether 500 effect steps can be
programmed. They can be distributed arbitrarily across the 16 effects. Adelay can
also be programmed as an effect step.

11.2.1 Effect programming using the effects website

You can set and program effects via the server website which can be accessed via
the effects tab at the bottom of the site:

56

To program an effect, select it first from the effect block at the bottom of the page. (If
the effect has been previously programmed, the corresponding effect steps are
displayed in the Effect Editor on the right hand side of the page.)

Use the function buttons in the Effect Editor to add or remove steps or delays. You
can select the target group or individual ECG for each step as well as the final dim
value and delay from the drop down menus. If you insert a delay as an effect step,
the effect control will pause until the next step is executed. You can thereby create a
list with the entire sequence control for each effect. . Each step can also be
repeated in a continuous loop. To do so, please tick the Effect loop mode box above
the list. If an effect runs in continuous mode, it is repeated until it is stopped either
via the communication object or by pressing a button on the website.

The individual buttons have the following functions:

Add del ay

Add effect step

Move effect step up

Move effect step down

Delete effect step

Please remember that the set values are only saved if you press the button. If you
change to another effect without saving, any changes you made are lost.

Use the Start and Stop buttons to activate and test the selected effect directly from
the page.

11.2.2 Effect programming via ETS in 'Extended Mode'

If you are using ETS in 'extended Mode' (Mode B), you can program effects in ETS.

Effect programming

Export effect list

Start effect

Stop effect

Program effect

When the list is complete, download it onto the device.

57

Go to the Effects page and select the required effect from the directory on the left­hand side. Move the groups and individual ECGs which are needed for this effect
from the directory on the right-hand side into the field in the middle using drag-and­drop. The order of the entries corresponds to the order of the individual effect steps.
You can also use drag-and-drop to move the delay times into the table and to
change the order of items within the list.

Use the fields 'Value' and 'Time' to set the final value to which you would like to dim
a group or ECG as well as the dimming time for each effect step. If you are setting a
delay, the entry in the 'Time' colum shows the length of the delay. Use the
descriptions field underneath the effect steps to enter a user-friendly name for each
effect. Tick the 'Repeating' box if you would like the selected effect to run
continuously.

Once the table of effect steps is complete, you need to download the effect onto the
DALI gateway. For this purpose, please press the download button in the bottom
right-hand corner.

In principal you can also use ETS to plan individual effects 'offline', independently of
the DALI system. The plug-in only has to be connected to the gateway for the
duration of the download.

12. Self-contained battery emergency lamps

The KDA-64 supports control gears used to run self-contained battery emergency
lights (device type 1 in accordance with EN 62386-202). Such devices contain a
battery which can supply the light with power in case of a general power failure.

58

12.1 Features

Principally a distinction is made between switchable and non-switchable devices for
self-contained battery lamps. A switchable device can be directly connected to a
lamp just like a 'normal' ECG. In normal mode the light (usually an LED) can be
switched and dimmed via DALI. Emergency lights with switchable ECGs therefore
require only 1 DALI device. The standard switch parameters and objects are
available for these devices.

In contrast to the 'switchable' device, a 'non-switchable' device (converter) can only
control the connected lamp in an emergency. To use the same lamp in normal mode
(switching, dimming), a second, 'normal' ECG is required. These lights are therefore
called emergency lights with 2 DALI devices. The two ECGs make a device pair.
'Non-switchable' devices use the DALI communication to query the device status
and to initiate mandatory test phases. As these devices cannot switch or dim
themselves, there are no parameters or objects for switch behaviour available for
these devices. During both new and post-installation the KDA-64 recognises
automatically, whether the connected device is a 'switchable' or 'non-switchable'
ECG. However, because of the DALI structure with its random assignment of short
addresses, the pairing of a 'normal' device with a 'non-switchable' device does not
occur automatically. It has to be performed manually on the parameter page in ETS.

The assignment is crucial for fault analysis purposes as 'non-switchable' devices
usually share the connected lamp with a 'normal' device. Without the assignment, a
lamp failure may be double-counted. In addition, the 'normal' ECG in a pair is
usually automatically disconnected from the power supply when the emergency
light is tested. This loss of function generates an ECG failure. However, by making
a pair, the gateway recognises automatically, whether a real ECG failure has
occurred or whether the corresponding converter has simply been tested. Only real
ECG failures are taken into consideration for alarm and analysis purposes. Please
remember that both the pairing and the fact that the power of the 'normal ECG' is
switched off by the emergency light ECG in test mode mean that any burn-in mode of
these ECGs is interrupted.

To identify the converters after installation, a function test starts for 'non-switchable'
ECGs. The process takes a few seconds. During this process the status LED on the
converter flashes (see function description of the respective converter). As these
devices cannot switch the connected lamp themselves, the normal identification
process through switch on/ switch off is not possible. The identification therefore
needs to occur via the LED.

12.2 Converter inhibit mode

Self-contained battery emergency lamps always change into emergency mode if
there is a power supply failure. The lamp is now operated by the internal battery.
However, it may become necessary at times to cut off the power supply, for example
during maintenance work or the initialisation phase of a building. To prevent the
lights from switching into emergency mode, the converters can be disabled via the

59

on the device (see above). This converter inhibit mode is only available for all
connected devices at the same time. If the power supply is turned off within 15
minutes after activating the mode, the connected lights do not change into
emergency mode and the lights remain switched off. When the power resumes, the
lights return to normal. If the 15 minutes run out without a power loss, all converters
are automatically re-set to normal mode.

12.3 Test mode

The KDA-64 supports mandatory tests for self-contained battery emergency lamps.

Attention: The legal regulations and norms vary in different countries. Please
make sure that you comply with all country-specific requirements.

The KDA-64 supports functional tests, long duration tests and battery tests.
Functional and long duration tests can be started externally via KNX telegrams (1
Byte telegrams, see below)or via the device website. Alternatively you may choose
to set automatic test intervals. This means tests are performed automatically via
the connected converters. (Please check the converter description for the exact
function.) Battery tests can be performed individually at any time. However, they are
also part of a functional or long duration test.

After a test has been completed, the test results are available on the KNX bus via
communication objects and they may be recorded in the visualisation. The
corresponding 3 Byte object is updated with the test result and automatically sent
after every new test. The object can be queried at any time. The object provides the
result of the last test. In addition to the latest test result the object also displays the
current status (test pending, test running).

Attention: Please remember that the object is only updated with the latest test
result once the test has been completed. If a test is started and the object is
queried before the test is complete (which can be seen from the status flag
“test pending” or “test running) the test result shown is that of the previously
completed test.

Alternatively, or in addition to reporting via communications objects to the bus, test
results can be displayed on the website if you select the respective converter.

60

The website displays the most recently executed test with results and date/time of
the test.

13. ETS communication objects overview

The KDA-64 communicates via the KNX bus based on powerful communication
stacks. Altogether 871 communication objects are available for the communication.

13.1 General communication objects

The general communication objects 1 to 22 only exist once and apply to the gateway
as a whole.

61

This object is used to set all connected lights to a certain value.
However, any connected ECGs that are in special mode (Burn-In,
Emergency Test, Panic Mode) are excluded and the DALI bus is
addressed sequentially. A delay between the value setting of the first
and last light may hence be visible. If none of the ECGs is in special
mode, the value setting is performed simultaneously via DALI
Broadcast telegrams.

This object is used to activate or stop the test mode for emergency
lights with central battery via the bus. Self-contained battery lamps
are controlled individually.

This object is used to activate or stop the night-time mode via the bus.

This object is used to activate or stop the emergency mode via the
bus.

62

2

4

5

3

Broadcast,
Set Value

Activate Test
Mode

Activate Test
Mode

Activate
Emergency
Mode

Value

Activate / Stop

Activate / Stop

Activate / Stop

1 Byte

1 B ti

1 B ti

1 Bit

CW

CW

CW

CW

This object is used to switch all connected lights on or off. However,
any connected ECGs that are in special mode (Burn-In, Emergency
Test, Panic Mode) are not switched and the DALI bus is addressed
sequentially. A delay between the switching off the first and last light
may hence be visible. If none of the ECGs is in special mode, the
switching is performed simultaneously via DALI Broadcast telegrams.
The Broadcast function always switches to 0 or 100%. The 'switch-off
value' and 'switch-on value' parameters are not considered.

Obj1Object name

Broadcast,
Switching

Function

On/Off

Type

1 Bit DPT:

Flags

CW

This object is used to start or stop effects. Up to 16 effects are
available on the DALI gateway. To start an effect, set the top Bit. The
effect stops when Bit 7 is deleted. This means:

63

Obj

7

Effect Off Effect On

Start Program

Effect 1 0 281
Effect 1 2921

Effect 15 14 142
Effect 1 16 5 143

Object name

Effects start /
stop

Function

Effect No.

Type

8 Bit

Flags

CW

This object is used to report the presence of a general failure in the
connected DALI segment independent of its type.

This object is used to report the presence of a DALI short-circuit in the
connected DALI segment.

8

9

General
Failure

DALI Failure

Yes/No

Yes/No

1 B ti

1 B ti

CRT

CRT

This object is used to report that the total of all lamp, ECG and
converter failures exceeds the set threshold.

10

General Failure
Exceeds
Theshold

Activate / Stop 1 Bit CRT

This object is used to invoke or program scenes. Up to 16 scenes are
available on the DALI gateway. To program a scene, you must set the
top bit:

6

Start Program

Start Program

Scene 1 01 28
Scene 2 11 29

Scene invoke /
program

Scene No. 8 Bit CW

Scene 15 14 142
Scene 116 5 143

64

Obj Object name Function Type Flags

This object is used to report that the total of all lamp failures
recognised by the gateway exceeds the set threshold.

This object is used to report that the total of all ECG failures
recognised by the gateway exceeds the set threshold.

12

14

Lamp Failure
Exceeds
Theshold

ECG Failure
Exceeds
Theshold

Ja / Nein

Ja / Nein

1 Bit

1 Bit

CRT

CRT

This object is used to report the total amount of lamp failures
recognised by the gateway.

This object is used to report the total amount of ECG failures
recognised by the gateway.

This object is used to report the failure rate as a percentage of the
total number of lamps in the DALI segment.

13a

15a

13b

Lamp Failure
in Total

ECG Failure
in Total

Lamp Failure
in %

Value

Value

Value

1 Byte

1 Byte

1 Byte

CRT

CRT

CRT

This object is used to report the total number of all lamp, ECG and
converter failures recognised by the gateway. Please remember that
for each connected device a fault is counted just once. A simultaneous
lamp failure in case of an ECG or converter failure cannot be
recognised or counted.

Alternatively, this object is used to report the failure rate as a
percentage of the total number of devices in the DALI segment. All
lamp, ECG and converter failures are hereby taken into consideration
Please remember that for each connected device a fault is counted
just once. A simultaneous lamp failure in case of an ECG or converter
failure cannot be recognised or counted.

11a

11b

General Failure
in Total

General Failure
in %

Value

Value

1 Byte

1 Byte

CRT

CRT

65

Obj Object name Function Type Flags

Alternatively, this object is used to report the failure rate as a
percentage of the total number of converters in the DALI segment.

17b

Converter Failure

in %

Value 1 Byte CRT

This object is used to send the switch status of individual lamps in the
DALI segment when the system is started or when a change has taken
place. Bit 0 - 5 refer to the number of the ECG. Bit 6 shows the
corresponding status on/off. For example:

Bit 7 6 5 4 3 2 1 0
ECG 5 / On 0 1 0 0 0 1 0 0
ECG 6 / Off 0 0 0 0 0 1 0 1

If a value is received where Bit 7 and Bit 6 are set, it is interpreted as a
status query. For example:

Bit 7 6 5 4 3 2 1 0
ECG 5 / Query 1 1 0 0 0 1 0 0

The gateway responds with the current status of the queried ECG.
Bit 7 6 5 4 3 2 1 0
ECG 5 / On 0 1 0 0 0 1 0 0

18

Status
Switching
Lamp

Status 8 Bit CWT

This object is used to report that the sum of converter failures
recognised by the gateway exceeds the set threshold.

16

Converter Failure

Exceeds
Theshold

Yes/No 1 Bit CRT

This object is used to report the total amount of all converter failures
recognised by the gateway

Alternatively, this object is used to report the failure rate as a
percentage of the total number of ECGs in the DALI segment.

17a

15b

Converter Failure

in Total

ECG Failure
in %

Value

Value

1 Byte

1 Byte

CRT

CRT

66

Obj Object name Function Type Flags

This object is used to send the failure status of lamp or ECG failures in
the DALI segment when the system is started or when a change has
taken place. Bit 0 to 5 refer to the number of the ECG. Bit 7 represents
an ECG failure, Bit 6 a lamp failure. For example:

Bit 7 6 5 4 3 2 1 0
ECG 5 / ECG failure 1 0 0 0 0 1 0 0
ECG 6 / Lamp failure 0 1 0 0 0 1 0 1

If a value is received where Bit 6 and Bit 7 are set, it is interpreted as a
status query. For example:

Bit 7 6 5 4 3 2 1 0

ECG 5 / Query 1 1 0 0 0 1 0 0

The gateway responds with the current failure status of the queried
ECG.

Bit 7 6 5 4 3 2 1 0
ECG 5 / ECG failure 1 0 0 0 0 1 0 0

Time stamps are used for the analysis of self-contained emergency
ballast faults. This requires the current date and time which are made
available via the Bus. Two objects are used for this purpose.

20

Failure Status
Lamp/ECG

Status 8 Bit CWT

This object is used to send the value status of individual lamps in the
DALI segment when the system is started or when a change has taken
place. Bit 8 to 13 refer to the number of the ECG. Bit 14 shows the
switch status. Bit 0 to 7 represent the corresponding status 0..100%.
For example:

ECG 5 / On 0 1 0 0 0 1 0 0 Bit 15..8
Value 50% 1 0 0 0 0 1 0 0 Bit 7..0

If a value is received where Bit 14 and Bit 15 are set, it is interpreted
as a status query. For example:

ECG 5 / Query 1 1 0 0 0 1 0 0 Bit 15..8

0 0 0 0 0 0 0 0 Bit 7..0

The gateway responds with the current status of the queried ECG.

ECG 5 / On 0 1 0 0 0 1 0 0 Bit 15..8
Value 50% 1 0 0 0 0 1 0 0 Bit 7..0

19

Status Value
Lamp

Status 16 Bit CWT

67

13.2 ECG-related communication objects

A set of 11 communication objects is available for each one of the up to 64
connected ECGs / converters and corresponding lamps. The communication
objects are only shown for those ECGs / converters that were found during system
installation. The objects are also partly hidden when ECGs have been assigned to a
group. Lamps can only be controlled individually if they have not been

assigned to a group.

The following objects are available (Example ECG 1):

Obj Object name Function Type Flags

This object is used to switch an ECG on or off if it is not in special
mode (burn-In, test mode emergency lights, panic/ emergency mode).

167

ECG1,
Switching

On/Off 1 Bit CW

Obj Object name Function Type Flags

This object is used to set the time. The time must be provided by a
central timer and updated at least twice a day.

This object is used to set the date. The date must be provided by a
central timer and updated at least twice a day. Leap years and
change-over to and from daylight saving time are not taken into
consideration during internal calculations of time and date. Therefore
please pay attention that the timer sends the correct date on these
occasions.

21

22

Time

Date

Time

Date

3 Byte

3 Byte

CWT

CWT

This object is used for the relative dimming of an ECG that is not in
special mode (burn-in, test mode emergency lights, panic/ emergency
mode). Bit 4 is set to dim up and deleted to dim down. Bits 0..3 refer to
the increment size. Bit 0..3 deleted is interpreted as a stop telegram.

168

ECG1,
Dimming

Brighter / Darke 4 Bit CW

68

Obj Object name Function Type Flags

This object is used to send the ECG switch status. Any value >0% is
interpreted as ON.

This object is used to send the ECG value status.

This object is used to send the failure status of lamp, ECG and
converter failures.

Alternatively this object is used to send the failure status for lamp,
ECG and converter failures as a 1Byte object.

Bit 0 Lamp failure
Bit 1 ECG failure
Bit 2 Converter failure

The operating hours of a lamp are sent via this object. The internal
counter can be set to 0 (Reset) or another value via this object.

Please remember:
The “Write“ flag is switched off in the presetting.

171

172

173a

173b

174

ECG1, Status

ECG1, Status

ECG1, Failure
Status

Failure Status,
ECG1

ECG1, Operating

Hours

On/Off

Value

On/Off

Status

Value

1 Bit

8Bit

1Bit

1 Byte

4Byte

CRT

CRT

CRT

CRT

CRT

This object is used to set the value of ECG1 unless it is in special
mode (burn-in, test mode emergency lights, panic/ emergency mode).

This object is used to start or finish the automatic burn-in of ECG1.
During the burn-in process all other switch, dim or value telegrams are
ignored and the lamp runs at full light level. The burn-in period
normally finishes automatically after the configured burn-in time. If
you switch the burn-in period off via this object, the timer stops and
you need to re-start the automatic burn-in.

169

170

ECG 1,
Set Value

ECG1,
Burn In

Val ue

On/Off

1 Byte

1 Bit

CW

CWT

69

Obj Object name Function Type Flags

This object is used to start a long duration test, functional test and
battery test of the converter. The individual Bits have the following
meaning:

Bit 0 Start functional test
Bit 1 Functional test pending
Bit 2 Start duration test
Bit 3 Duration test pending
Bit 4 Query battery status
Bit 5 Battery status query pending
Bit 6 Functional test running
Bit 7 Duration test running

This object is used to analyse the results of functional tests, long
duration tests and battery tests. The individual Bits have the following
meaning:

Bit 23..16 Battery status 0..100%→ If test is Function or Battery test:

If test is Duration test: Test time of Duration test in steps

of 2 Minutes
Bit 15 Fault during long duration test→
Bit 14 Fault during functional test→
Bit 13 Maximum time for long duration test exceeded→
Bit 12 Maximum time for functional test exceeded→
Bit 11 Emergency lamp faulty→
Bit 10 Battery faulty→
Bit 9 Battery operating hours too short→
Bit 8 Converter faulty→
Bit 7 Long duration test pending→
Bit 6 Function test pending→
Bit 5 Duration test running→
Bit 4 Function test running→
Bit 3 Test error during the last test→
Bit 2 Last test was battery query→
Bit 1 Last test was duration test→
Bit 0 Last test was function test→

176

177

Converter 1,
Test Sta rt

Converter 1,
Test Result

Start

Test

1 Byte

3 Byte

CW

CRT

This object is used to send a status message when the configured life
time of a lamp is exceeded.

If the connected DALI device is a converter for the control of self­contained battery emergency lights, two further objects are shown:

175

ECG1, Life Time

Exceeded

Yes/No 1 Bit CRT

70

Obj Object name Function Type Flags

This object is used to switch group 1 on or off.

This object is used for the relative dimming of group 1. Bit 4 is set to
dim up and deleted to dim down. Bits 0..3 refer to the increment size.
Bit 0..3 deleted is interpreted as a stop telegram.

This object is used to set the value of group 1.

This object is used to enable the operation of group 1:
Object = 0 Disabled→
Object = 1 Enabled→

This object is used to disable the operation of group 1:
Object = 0 Disabled→
Object = 1 Enabled→

23

24

25

26a

26b

Group 1,
Switching

Group 1,
Dimming

Group 1,
Set Value

Group 1,
Enable

Group 1,
Disable

On/Off

Dimmen

Value

Yes/No

Yes/No

1 Bit

4itB

1 Byte

1 Bit

1 Bit

CW

CW

CW

CW

CW

The objects described above for ECG 1 / converter 1 are available in the same
format for the ECGs / converters 2 to 64. The object number always increases by 11
objects. For example, ECG 2: dimming object 179, etc.

13.3 Group-related communication objects

A set of 8 communication objects is available for each one of the up to 16 possible
groups. The communication objects are only shown for those groups that are in use.

ECGs / that have been assigned to a group can no longer be controlled
individually.

The following objects are available (Example group 1):

71

Obj Object name Function Type Flags

This object is used to send the value status of the group.

This object is used to send the failure status of a lamp, ECG or
converter failure within the group.

This object is used to send the failure status for lamp, ECG and
converter failures within the group as a 1Byte object.

→Bit 0 Lamp failure

→Bit 1 ECG failure

→Bit 2 Converter failure

This object is used to report the total number of devices within the
group and the failure status according to type of failure. The different
Bits within the object have the following meaning:

Bit 31 | Bit 30 | Bit 29..24
Norm. ECG |Emerg.ECG |Number of ECG +

converter failures

Bit 23 | Bit 22 | Bit 21..16
Norm. Lamp|Emerg.Lamp|Number of lamp

failures

This object is used to send a message when the total of all lamp, ECG
and converter failures found within the group exceeds the threshold
set by parameters.

28

29a

29b

30

31a

Group 1,
Status

Group 1,
Failure Status

Group 1,
Failure Status

Group 1,
Failure Status

Group 1,
Failure Status

Value

Yes/No

Status

Status

Failure Status

8itB

1itB

1 Byte

4Byte

1itB

CRT

CRT

CRT

CRT

CRT

This object is used to disable the staircase mode:
Object = 0 Staircase mode enabled→
Object = 1 Staircase mode disabled→

This object is used to send the switch status of the group. Any value
>0% is interpreted as ON.

26b

27

Group 1, Disable

Staircase Function

Group 1, Status

Yes/No

On/Off

1 Bit

1 Bit

CW

CW

72

14. ETS parameter overview

The ETS parameters of the device are distributed across different parameter pages.
To simplify the overview, only the parameter pages of the device selected in the
function tree are displayed.

14 1 Device: General Settings.

The ”General Settings“ item has 5 parameter pages. The parameters are described
below:

14 1.1 Parameter page: General Settings.

Parameter Settings
Device Name

(max. 30 char.)

< -64>KDA

Use this parameter to enter a user-friendly name for the
DALI Gateway.

IP Adress Assignment Manual Input

via DHCP

The KDA-64 can either be assigned a xed IP address or a
dynamic address assigned by The pa-a DHCP server.
rameters for the xed IP address are only ou se-visible if y
lect " anual Input"M

Disable Button Operation

No
Yes

This object is used to send the total of all lamp, ECG and converter
failures within the group.

This object is used to report the failure rate as a percentage of the
total number of devices within the group.

31b

31c

Group 1,
Failure

Group 1,
Failure Rate

Value

Value

1 Byte

1 Byte

CRT

CRT

73

Parameter Settings

Password Admin Access

0
You can configure a password for the configuration area of
the website. Passwords consist of numbers between 0 and

14 1.2 Parameter page: IP Settings.

Parameter Settings
IP Address (byte 1)

0

IP Address (byte 2)

0

IP Address (byte 3)

0

IP Address (byte 4)

0

This sets the xed IP address of the KDA-64 if you do not
select the DHCP mode.

Subnet Mask (byte 1)

255

Subnet Mask (byte 2)

255

Subnet Mask (byte 3)

255

Subnet Mask (byte 4)

0

This sets the subnet mask of the KDA-64 if you do not se­lect the DHCP mode.

Gateway te 1)Address (by

255

Gateway te 2)Address (by

255

Gateway te 3)Address (by

255

Gateway te 4)Address (by

0

This sets the address of a standard gateway for direct ac-
cess via the Internet. The setting is only ou dopossible if y
not select the DHCP.

Use this parameter if you would like to disable the control
and conguration of the device via its display and pushbut-
tons. This option is to prevent manipulation of a running
installation.

Password User Access

0

You can congure a password for the user area of the web­site. Passwords consist of numbers between 0 and 9999.

Password for Conguration

0

74

14 1.3 Parameter page: Behaviour.

Parameter Settings
Behaviour on KNX Failure

No Action
Switch to On-Value
Switch to Off-Value
Switch to Emergency Value

Use this parameter to set the behaviour of the connected
ECGs/lamps on KNX failure.

Behaviour on KNX Voltage
Recovery

No Action
Switch to Last Value
Switch to On-Value
Switch to Off-Value

Use this parameter to set the behaviour of the connected
ECGs/lamps on KNX voltage recovery or bus reset.

Light Status Send Condi­tion

Send on Request
Send on Change
Send on Change and after

Busreset

Use this parameter to determine the light status send condi­tions (switch status and value status) of the connected
ECGs and groups.

Delay een Statusbetw
Objects

No Delay
1 Second
2 Seconds
3 Seconds
4 Seconds
5 Seconds
10 Seconds

Use this parameter to set a delay een individual statusbetw
telegrams. This can help to prevent a large bus load, for
example for broadcast switching.

Delay for Sending on KNX
Recovery

immediately
5 Seconds
10 ondsSec
15 Seconds
20 Seconds
30 Seconds
40 Seconds
50 Seconds

Use this parameter to set a delay for sending status objects
after KNX voltage recovery a bus reset. In installationsor
with more than one gateway different settings for this pa-
rameter can prevent all devices from sending at the same
time.

75

Parameter Settings
Send Status Value During

Dimming

If Change > 2%
If Change > 5%
If Change > 10%
If Change > 20%
inactive

Use this parameter to set whether and when you would like
a status value to be sent via a 4 bit dim telegram during
dimming (relative dimming). If you use the setting inactive
the value is only sent after the dimming process is com-
plete.

Behaviour after Burn In

Switch to Off-Value
Switch to On-Value
Switch to Last Value

Use this parameter to set the light value of ECGs / lamps
after their burn-in period. If you use ' witch to Last Value'S
the value prior to the burn-in is saved and the lamp returns
to this value afterwards.

Behaviour after Emergency
Test

Switch to Off-Value
Switch to On-Value
Switch to Last Value

Use this parameter to set the light value of ECGs / lamps
after a central battery ou useemergency luminaire test. If y
'Switch to Last Value' the value prior to the test mode is
saved and the lamp returns to this value afterwards.

Behaviour after Panic /
Emergency Mode

Switch to Off-Value
Switch to On-Value
Switch to Last Value

Use this parameter to set the light value of ECGs / lamps
after the panic/emergency ou usemode has finished. If y
'Switch to Last Value' the value prior to the panic mode is
saved and the lamp returns to this value afterwards

14 1.4 Parameter page: Special Functions.

Parameter Settings
General Status Object (1

Byte) for Switching Status

No
Yes

Use this parameter to select whether you would like to use
the general status object for switch status (object number

18).
General Status Object (2

Byte) for Value

No
Yes

Use this parameter to select whether you would like to use
the general status object for value status (object number

19).

76

Parameter Settings
Broadcast enabled

No
Yes

Use this parameter to select whether you would like to use
Broadcast functions.

14.1.5 Parameter page: Analysis and service

Parameter Settings
Failure Status Send

Condition

Send on Request
Send on Change
Send on Change and after

Bus reset

Use this parameter to set the conditions under which you
want the failure status of the connected ECGs and groups
to be sent.

Delay een Sending ofbetw
Failure Objects

No Delay
1 Second
2 Seconds
3 Seconds
4 Seconds
5 Seconds
10 Seconds

Use this parameter to set a delay een individual failurebetw
objects. This can help to prevent a large bus load, for ex­ample when a DALI segment loses power.

Cycle Time for DALI Failure
request

No Delay
0,5 ondsSec
1 Second
2 Seconds
3 Seconds
4 Seconds
5 Seconds
6 Seconds

To analyse ECG and lamp failures, a periodic request has
to be sent to the ECGs via DALI telegrams. Use this pa­rameter to set the time for these periodic requests. Atten­tion: If you set ' o request' ECG and lamp failures canN
no longer be ognised. You should therefore userec this
setting y ice or in special cases.onl for serv

Central Failure Object 1
Byte existing

No
Yes

Use this parameter to select whether you want to use the
central failure object for ECG and lamp failures (object
number 20).

Function of Failure Objects

Total Number of Failures
Failure Rate 0..100%

77

Use this parameter to select whether you want to use the
failure analysis objects (objects number 11, 13, 15 and 17)
to report the total amount of failures or the failure rate in %.

Threshold for Total Failures

Parameter Settings

1%
2%
3%

.....

100%

Use this parameter to congure a threshold value for the
general failure alarm object (object 10). The threshold
value takes all failures (ECG, lamp and converter failure)
into consideration and relates them to the total number of
connected ECGs and converters.

Threshold for Lamp
Failures

1%
2%
3%

.....

100%

Use this parameter to set a threshold value for the lamp
failure alarm object (object 12). The threshold value takes
all lamp failures into consideration and relates them to the
total number of connected lamps in the DALI segment.

Threshold for ECG Failures

1%
2%
3%

.....

100%

Use this parameter to set a threshold value for the ECG
failure alarm object (object 14). The threshold value takes
all ECG failures into consideration and relates them to the
total number of connected ECGs in the DALI segment.

Threshold for Converter
Failures

1%
2%
3%

.....

100%

Use this parameter to set a threshold value for the convert­er failure alarm object (object 16). The threshold value
takes all converter failures into consideration and relates
them to the total number of connected converters in the
DALI segment.

14.2 ECG No. xx

To set the ECG parameters, use the parameter pages listed under the devices ECG
1 to ECG 64.

78

Please remember that after the synchronisation only those ECGs are displayed that
were recognised during the installation. Accordingly there are fewer entries in the
function tree and fewer parameters and objects.

There are 4 parameter pages for ECG settings. The parameters are described
below.

14.2.1 Parameter page: ECG No. xx

Parameter Settings
ECG Type

Fluorescent Lamp
Self Contained Battery Lamp
Discharge Lamp
Low Voltage Halogen Lamp
Incandescent Lamp

0..10V Converter
LED Module
Relais Module

Use this parameter to set the type of ECG used. Normally
the ECG type is recognised automatically during installation
and set accordingly nchronisation. Some ECGin the sy
manufacturers, however, do not support this function. In this
case, you can set the ECG type manually n-. During the sy
chronisation process, the ETS compares the found value to
the pre-set value. If the two do not match, an alarm mes­sage appears that has to be acknowledged.

Emergency ithLuminaire w
Central Battery

No Emergency ireLumina
Central Battery Emergency

Luminaire

Use this parameter to set whether the ECG controls an
emergency ith central batteryluminaire w . Devices regis-
tered as emergency are specicallyluminaires marked dur-
ing status reports. A special test mode for such devices can
also be activated via an object. This parameter is not visi­ble if you select the type ' elf-contained batterys lamp'

Value in Test Mode

1..100% [30]

79

Parameter Settings
Use this parameter to select hether an emergencyw light is

used with a switchable or non-switchable converter. This
parameter is only ou select ' elf-contained batteryvisible if y s
lamp'asECGtype.

Normally pe is recognised automaticallythe ECG ty during
installation and set accordingly nchronisation.in the sy
Some ECG manufacturers, however, do not support this
function. In this case, you can set the ECG type manually.
During the synchronisation process, the ETS compares the
found value to the pre-set value. If the two do not match, an
alarm message appears that has to be acknowledged.

Converter controls ECG 1

ECG 2

....

ECG 64
not assigned

This parameter is only if you select a non-switchablevisible
converter as type of emergency itchable con-light. Non-sw
verters are normally ith twoused for an emergency lamp w
DALI devices. Use the parameter to manually select the
'normal ECG' that is assigned to the converter. The as­signment means that error messages that were caused by
the converter test mode are suppressed and a lamp failure
is not counted twice.

Operating Mode

Normal Mode
Permanent Mode
Normal / Night Mode

Use this parameter to select the operating mode of the
ECG.

Value in Permanent Mode

1..100% []50%

Use this parameter to select the value of a lamp in ' erma-p
nent mode' A lamp in this mode cannot be switched or
changed. It remains at the set value.

This parameter is only e if you select ' ermanentvisibl p
mode'

Behaviour in Night Mode

Delayed Switch-Off
Delayed Switch-Off in 2 Steps
Delayed Dim-Off
Activate Permanent Mode

and ignore telegrams

Use this parameter to set the behaviour of the ECG in night­time mode. This parameter is only ou select ' or-visible if y n
mal / night mode'

80

Parameter Settings
Automatic Switch-Off after 1 Minute

2 Minutes
3 Minutes
4 Minutes
5 Minutes
10 Minutes
15 Minutes

Automatic Switch-Off after 1 Minute

2 Minutes
3 Minutes
4 Minutes
5 Minutes
10 Minutes
15 Minutes
20 Minutes

Use this parameter to set the time after which an ECG in
night time mode automatically switches off. This parameter
is only ou select ' ormal / night mode'visible if y n

ECGs enabled for Panic
Mode

No
Yes

Use this parameter to enable an ECG for panic mode.

ValueonDALIPowerFail

1..100% [100]

Use this parameter to set the value of a lamp after a loss of
DALI power. The value is saved on the ECG and the device
automatically value when a power loss oc-changes to the
curs.

14.2.2 Parameter page: Emergency Settings

This page is only visible if you select 'self-contained battery lamp' as ECG type.

Parameter Settings
Value in Emergency Mode

1..100% [50]

Use this parameter to select the light value of a self con­tained battery lamp in case of a mains supply failure or dur­ing a long duration test.

Delay on Mains Recovery

No Delay
30 Seconds
1 Minute
2 Minutes
3 Minutes
4 Minutes
5 Minutes
10 Minutes

81

Parameter Settings
Use this parameter to set the delay till a self contained bat-

tery mode following mains recoverylamp returns to normal .
Interval of Long Duration

Test

No automatic testing
1 Week
2 Weeks

....

52 Weeks

Use this parameter to set the intervals at which the convert­er is to perform automatic long duration tests.

Interval of Functional Test No automatic testing

1 day
2 days

....

28 days

Use this parameter to set the intervals at which the convert­er is to perform automatic functional tests.

Test Execution Timeout
(Days)

0..255 [10]

If a functional or long duration test cannot be started imme­diately he battery as not full), the(for example because t w
converter tries to execute the test later on. Use this pa­rameter to set the length of time that the converter is to try
to execute the test and after which a test execution timeout
error is reported. If you select0, the timeout occurs after
15 minutes.

14 2 Parameter page itching Behaviour..3 :Sw

Parameter Settings
Switch-On Value 5%

10%

....

95%
100%
last Value

Use this parameter to set the switch-on value. If you select
'last value' the value is set to the dim value prior to the
lamp being switched off.

Switch-On Behaviour Set Value Immediately

Dim to Value in 10s
Dim to Value in 20s
Dim to Value in 30s
Dim to Value in 1 Minute
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes

82

Parameter Settings
Use this parameter to set the switch-on behaviour.

Switch-Off Value

0%
5%
10%

....

45%
50%

Use this parameter to set the switch-off value.

Switch-Off Behaviour Set Value Immediately

Dim to Value in 10s
Dim to Value in 20s
Dim to Value in 30s
Dim to Value in 1 Minute
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes

Use this parameter to set the switch-off behaviour.

Value-Set Behaviour Set Value Immediately

Dim to Value in 10s
Dim to Value in 20s
Dim to Value in 30s
Dim to Value in 1 Minute
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes

Use this parameter to value-set the behaviour on receipt of
a new dim value.

Time for Dimming 3 Seconds

4 Seconds
5 Seconds
6 Seconds
10 ondsSec
20 Seconds
30 Seconds
60 Seconds

Use this parameter to set the dim time for relative dimming.

Max. Value for Dimming 50%

55%

....

100%

83

Parameter Settings
Use this parameter to congure the maximum dim value

that can be set through relative dimming.
Min. Value for Dimming

0%
5%

....

50%

Use this parameter to congure the minimum dim value that
can be set through relative dimming.

Switch-On via Dimming

No
Yes

Use this parameter to select whether a switched off device
can be switched on when receiving a relative 4 Bit dim
command ' imming up'd

14.2.4 Parameter page:Analysis and service

Parameter Settings
Operating Hour Calculation Yes

No

Use this parameter if you would like to count the individual
operating hours of an ECG. .

Operating Hour Limit
(hours)

10..120.000h [4000h]

Use this parameter to set the limit of a lamp' operatings
hours. An alarm is sent when the limit is reached.

Enable Burn In Feature Yes

No

Use this parameter to enable the burn in feature.

Burn In Duration (hours)

1..100h [24h]

Use this parameter to set the duration of the burn-in phase.
During this phase the lamp cannot be switched off or
dimmed.

Type of Failure Object

1Bit
8Bit

Use this parameter to select whether the failure object is to
be sent as a 1 Bit object without differentiation according to
type of failure or as an 8 Bit object with failure differentia­tion.

14.3 Group No. xx

To set the group parameters, use the parameter pages listed under group1 to group

16.

84

Parameter Settings
Operating Mode

Normal Mode
Permanent Mode
Normal / Night Mode
Staircase Mode

Use this parameter to set the operating mode of the group.

Value in Permanent Mode

0..100% [100]

Use this parameter to select the value of all lamps in a
group in ' ermanent mode' Lamps in this mode cannot bep
switched or changed. They remain at the set value.

Behaviour in Night Mode

Delayed Switch-Off
Delayed Switch-Off in 2 Steps
Delayed Dim-Off
Activate Permanent Mode

and ignore telegrams

Use this parameter to set the behaviour of the group in
night-time mode. This parameter is only ou selectvisible if y
normal / night mode'

Automatic Switch-Off after 1 Minute

2 Minutes
3 Minutes
4 Minutes
5 Minutes
10 Minutes
15 Minutes
20 Minutes

There are 3 parameter pages for group settings. The parameters are described
below.

14.3.1 Parameter page: Group No. xx

85

Parameter Settings
Use this parameter to set the time after which a group in
night time mode automatically switches off. This parameter
is only ou select ' ormal / night mode'visible if y n

Function of Additional
Object

No Object
Disable Object
Release Object
Disable Staircase Function

Object

Use this parameter to set the function of an additional ob­ject.

Enabled for Emergency /
Panic Mode

No
Yes

Use this parameter to enable a group for panic/emergency
mode.

14 3.2 Parameter page: Switching behaviour.

Parameter Settings
Switch-On Value 1%

10%
?
95%
100%
Last value

Use this parameter to set the switch-on value. If you select
' ast value' the value is setl to the dim value prior to the
lamps being switched off.

Switch-On Behaviour Set Value Immediately

Dim to Value in 10s
Dim to Value in 20s
Dim to Value in 30s
Dim to Value in 1 Minute
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes

Use this parameter to set the switch-on behaviour.

Switch-Off Value

0%
5%
10%

....

45%
50%

86

Parameter Settings
Use this parameter to set the switch-off value.

Switch-Off Bahaviour Set Value Immediately

Dim to Value in 10s
Dim to Value in 20s
Dim to Value in 30s
Dim to Value in 1 Minute
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes

Use this parameter to set the switch-off behavior.

Value-Set Behaviour Set Value Immediately

Dim to Value in 10s
Dim to Value in 20s
Dim to Value in 30s
Dim to Value in 1 Minute
Dim to Value in 2 Minutes
Dim to Value in 5 Minutes
Dim to Value in 10 Minutes

Use this parameter to value-set the behaviour on receipt of
a new dim value.

Time for Dimming 3 Seconds

4 Seconds
5 Seconds
6 Seconds
10 Seconds
20 Seconds
30 Seconds
60 Seconds

Use this parameter to set the dim time for relative dimming.

Max. Value for Dimming 50%

55%

....

100%

Use this parameter to configure the maximum dim value
that can be set through relative dimming.

Min. Value for Dimming

0%
5%

....

50%

Use this parameter to configure the minimum dim value that
can be set through relative dimming.

87

Parameter Settings

Switch-On via Dimming

No
Yes

Use this parameter to select whether a switched off group
can be switched on when receiving a relative 4 Bit dim
command ' imming up'd

14.3.3 Parameter page: Analysis and service

Parameter Settings
Type of Failure Status Ob-

ject

1Bit

8Bit
Use this parameter to select whether you want the failure

status object of the group to be sent as a 1 Bit object with­out type of failure information or as an 8 Bit object with fail­ure differentiation.

Additional Failure Object
for

Failure Number / Rate

Failure Threshold Exceeded
Use this parameter to select whether you would like to use

the additional failure object as a 1 Byte object for failure
number /rate or as a 1 Bit object for when the failure
threshold is exceeded.

Failure Threshold for Fail­ure Alarm Output

1%...100% []1%

Use this parameter to enter the threshold value in %. The
alarm object is sent when the value is exceeded. This
parameter is only ou select " ailure Thresholdvisible if y F
Exceeded" as additional failure object.

Function of Additional Fail­ure Object

Total Number of Failures

Failure Rate 0..100%

Use this parameter to select whether you want the addition­al failure object to send the total amount of failures within
the group or the failure rate in %. This parameter is only
visible if you select " ailure Number / Rate" as additionalF
failure object.

15. Firmware version and update

The firmware version of the DALI gateway is divided into main number, sub-number
and revision number (e.g. 1.2_05). The display on the device front only shows the
main and sub-number (Vers. 1.0). For full details regarding the current firmware
(version and revision) please refer to the device website where the current version
is visible in the bottom right-hand corner of the information window. (1.2_05).

88

The KDA-64 offers you the possibility of an easy firmware upgrade without having to
demount the device.

Future developments or any adjustments that may be required can be easily
imported via the IP connection.

If there is an update, an update file will be made available to you within an update
tool. The update file can be directly downloaded onto the device via the tool. For
more details regarding this process, please see the application note (pdf format)
included with the update.

16. Reset to conditions at delivery

To reset the device to its original settings, press all three buttons on the front of the
device and the programming button simultaneously whilst the power supply is
connected.

This leads to a factory reset. All device settings return to their status at delivery and
the device has the physical address 15.15.255.

No.28, Wuquan 3rd Rd., Wugu Dist., New Taipei City 248,Taiwan