Page 1
MC627ES
MC627ES
Owner's Manual
Page 2
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
AUGER HOUSING / IMPELLER ASSEMBLY
5
11
6
11
15
14
7
31
31
16
10
9
2
9
33
32
30
29
37
28
17
26
8
27
37
9
36
20
21
22
23
11
12
4
13
11
3
12
1
34
25
35
22
21
18
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
19
20
24
23
2 (EXPLODED)
01.07.026-D
Page 3
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
AUGER HOUSING / IMPELLER ASSEMBLY
KEY PART
NO. NO. DESCRIPTION
1 175321X431 IMPELLER
2 427148 GEARBOX ASSEMBLY
3 188909 BEARING
4 427146 IMPELLER PULLEY
5 175322 DISCHARGE BASE
6 178675X431 CORNER BRACKET
7 192199 CLEAN OUT TOOL
8 405400 TOOL CLIP
9 73800400 NUT 1/4-20
10 74780426 SCREW 1/4-20 X .625
11 427942 NUT 5/16-18
12 163183 SCREW 5/16-18 X .625
13 427145 IMPELLER HUB
14 427154 IMPELLER SLEEVE
15 73900600 NUT 3/8-16
16 180355 CARRIAGE BOLT
17 194189 SCREW 13-16 X .625
18 407760 PLUG
19 427302 GEARBOX COVER RH
20 427345 GASKET
21 407770 SEAL
22 407762 BEARING
23 174697 THRUST WASHER 1.00
24 407763 WORM GEAR
25 407764 AUGER SHAFT
26 189282 SQUARE KEY
27 407758 BEARING
28 174683 THRUST WASHER
29 427147 IMPELLER SHAFT
30 184205 ROLL PIN
31 174681 THRUST WASHER
32 174684 THRUST BEARING
33 407769 BEARING
34 407768 O-RING
35 407767 SCREW 5/16-18 X .750
36 427317 GEARBOX COVER LH
37 192090 SHEAR BOLT
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
21
Page 4
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
AUGER HOUSING / IMPELLER ASSEMBLY
1
KEY PART
NO. NO. DESCRIPTION
1 404929X421 AUGER HOUSING 27
2 404932X431 SCRAPER BAR
3 72270505 CARRIAGE BOLT 5/16−18 X .625
4 155377 NUT 5/16−18
3 (5x)
4 (5x)
2
01.07.002-A
2
KEY PART
NO. NO. DESCRIPTION
1
1 420495X431 AUGER 27 LH
2 420496X431 AUGER 27 RH
01.07.018-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
22
Page 5
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
AUGER HOUSING / IMPELLER ASSEMBLY
2
1
1
2
KEY PART
NO. NO. DESCRIPTION
3
1 420478 AUGER BEARING
2 411939 BEARING PLUG
3 179582 SCREW 5/16−18 X 1.00
3
01.07.024-B
4
3
3
KEY PART
NO. NO. DESCRIPTION
1 174762
X431 SKID PLATE LH
2 178777X431 SKID PLATE RH
4
01.11.001-B
1
3 72270506 CARRIAGE BOLT 5/16−18 X .75
4 751153 NUT 5/16−18
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
23
2
Page 6
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
CONTROL PANEL / CHUTE
11
2
10
5
8
3
6
9
11
6
4
11
7
1
6
13
12
01.09.005-E
KEY PART
NO. NO. DESCRIPTION
1 435023X421 CHUTE WELDMENT
2 178633X421 DEFLECTOR WELDMENT
3 420325 DEFLECTOR SEAL
4 179096X421 STRAP
5 189713X428 KNOB BLACK
6 128415 POP RIVET
7 185600 SHOULDER BOLT 1/4−20 X .704
8 72270505 CARRIAGE BOLT 5/16−18 X .625
9 191730 NUT 1/4−20
10 155415 WASHER
11 179246 PLASTIC WASHER
12 430324 CHUTE SNOW SHIELD
13 419822X431 SHIELD RETAINER STRAP
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
24
Page 7
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
CONTROL PANEL / CHUTE
2
2
1
*3
*6
KEY PART
NO. NO. DESCRIPTION
1 428272 LEVER/CABLE ROTATOR ASSEMBLY
2 17501010 SCREW 10-24 X .625
*3 420678 ROTATOR HEAD
*4 405932 ROTATOR PIVOT BRACKET
*5 420675 PULLEY PIVOT
*6 428273 CABLE ASSEMBLY ADJUSTABLE
*7 428310 CABLE ASSEMBLY HEAT SHIELD
*4
*7
01.09.010-B
*5
NOTES:
1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
25
Page 8
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
HANDLES
5
1
6
8
2
5
8
6
8
9
4
7
3
9
01.08.003-A
KEY PART
7
NO. NO. DESCRIPTION
1 419800X431 PLOW HANDLE LH
2 419801X431 PLOW HANDLE RH
3 196944X431 PANEL BRACKET LH
4 196943X431 PANEL BRACKET RH
5 199513 HANDLE GRIP
6 74780512 SCREW 5/16−18 X .750
7 74780524 SCREW 5/16−18 X 1.50
8 751153 NUT 5/16−18
9 155415 WASHER
1
KEY PART
NO. NO. DESCRIPTION
1 419797X431 LOWER HANDLE
2 427513X431 PIVOT SUPPORT WELDMENT
3 428867 SCREW 5/16−18 X .750
2
4 17000616 SCREW 3/8−16 X 1.00
4
3
4
3
01-05-013-A
4
4
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
26
Page 9
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
HANDLES
10
11
8
9
9
5
7
6
3
8
13
7
4
1
13
2
12
14
01.08.002-F
14
12
KEY PART
NO. NO. DESCRIPTION
1 412683X431 CONTROL PANEL
2 424517X431 CONTROL LEVER LH
3 424516
4 412679X008 TRACTION ROD ARM
5 426918X008 IMPELLER ROD ARM
6 412677 INTERLOCK BAIL
7 421613 SPACER
8 169675 RETAINER
9 17060410 SCREW 1/4-20 X .62
10 414280 KNOB BLACK
11 414281 KNOB RED
12 178899 HANDLE KNOB
13 19131316 WASHER 3/8
14 72120618 CARRIAGE BOLT 3/8-16 X 2.25
X431 CONTROL LEVER RH
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
27
Page 10
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
HANDLES
2
10
KEY PART
NO. NO. DESCRIPTION
1 180480 IMPELLER ROD
10
1
3
8
9
2 405740 TRACTION ROD
3 180445 SHIFTER ROD TOP
4 187716 SHIFTER ROD BOTTOM
5 180447 SPRING SLEEVE
6 178669 IMPELLER SPRING
7 180926 TRACTION SPRING
8 72270505 CARRIAGE BOLT 5/16-18 X .625
9 155377 NUT 5/16-18
10 169675 RETAINER
4
5
10
7
5
6
01.12.001-E
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
28
Page 11
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
HANDLES
7
1
4
3
5
2
KEY PART
NO. NO. DESCRIPTION
1 183346 CONSOLE PANEL
2 178668 HEADLIGHT BEZEL
3 180927 FLOOD HEADLIGHT
4
6
5
4 184471 SHOULDER SCREW 10−24 X .625
5 175262 SCREW 10−24 X 1.25
6 178770 WIRE HARNESS
7 183784 BULB
01.10.003-B
4
KEY PART
NO. NO. DESCRIPTION
1 412675X431 INTERLOCK SPRING
2 414572 INTERLOCK CAM
3
3 178831 TORSION SPRING
4 169675 RETAINER
5
2
5 17060410 SCREW 1/4−20 X .625
6 421252X431 INTERLOCK STOP
1
6
01.08.007-B
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
29
Page 12
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
DRIVE
42 EXPLODED
46
2
45
48
51
52
6
24
16
1
15
14
29
15
53
23
31
30
36
9
12
11
9
8
9
10
11
53
7
5
53
3
27
26
11
53
13
28
26
20
21
17
35
32
19
53
33
38
34
18
22
24
33
47
49
24
50
23
4
23
4
53
39
24
25
37
39
40
41
42
43
44
01.02.013-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
30
Page 13
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
DRIVE
KEY PART
NO. NO. DESCRIPTION
1 198875 SPEED SELECTOR
ASSEMBLY
2 17501010 SCREW 10-24 X .625
3 402685X421 END PLATE
4 17490508 SCREW 5/16-18 X .50
5 57079 WASHER
6 405485 CONTROL ARM
7 198580 CLEVIS PIN
8 403097X431 SHIFTER PLATE
9 402881 SHOULDER BOLT
10 403096X431 SHIFTER BRACKET
11 191730 NUT 1/4-20
12 402856X431 CLUTCH PLATE
13 416717X431 CLUTCH BRACKET
14 187101 SHIFTER LINK
15 700279 RETAINER
16 427542 CONTROL SHAFT
17 402568 CLUTCH ROD
18 169675 RETAINER
19 401732 SHIFTER YOKE
20 402310 PIVOT ROD
21 12000036 RETAINER
22 402878 RETURN SPRING
23 751153 NUT 5/16-18
24 408981 BEARING
25 73930500 NUT 5/16-18
26 198176X431 RUBBER WHEEL PLATE
KEY PART
NO. NO. DESCRIPTION
27 179831 RUBBER RING
28 175344 BEARING
29 178613 WHEEL HUB
30 74760514 SCREW 5/16-18-.875
31 12000012 RETAINER RING
32 402187 SPROCKET SHAFT
33 401619 CHAIN
34 417234 SPROCKET WELDMENT
35 401984X431 SHIFTER BRACKET
36 180135 SPRING
37 402652 PLATE PIVOT ROD
38 428288 E-RING .375
39 184471 SHOULDER SCREW
40 410877 BOTTOM PAN
41 413429X431 SPRING BRACKET
42 402689 DRIVE PLATE ASSEMBLY
43 414557 IDLER SPRING
44 178828 IDLER SPRING
45 402504 PULLEY SHAFT
46 401820 DRIVE PLATE
47 198791 BEARING
48 402393 PULLEY HALF
49 17541008 SCREW 10-24 X .50
50 402511 SPACER BEARING
51 418894X431 SWING PLATE
52 132010 NUT 3/8-16
53 428867 SCREW 5/16-18 X .750
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
31
Page 14
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
DRIVE
5
6
7
1b
6
2
3
5
4
01.03.005-B
1b
3
1a
KEY PART
NO. NO. DESCRIPTION
1 188226 (assy of 1a,1b) AXLE ASSEMBLY
1a 179352 AXLE SHAFT
1b 184206 ROLL PIN 3/16
2 402691 SPROCKET
3 174697 THRUST WASHER
4 179830 BEARING
5 17490508 BOLT 5/16−18 X .500
6 155443 CLIK PIN
7 189282 SQUARE KEY
4
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
32
Page 15
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
CHASSIS / ENGINE / PULLEYS
2
3
2
3
KEY PART
1
01.00.034-A
NO. NO. DESCRIPTION
- - 423474 COMPLETE LCT ENGINE
1 418694X421 FRAME
2 150406 BOLT 3/8-16
3 428867 SCREW 5/16-18 X .750
1
KEY PART
NO. NO. DESCRIPTION
1 427963X421 ENGINE MOUNTING PLATE
01.01.004-A
1
KEY PART
NO. NO. DESCRIPTION
1 428684 COVER ASSEMBLY
01.21.013-B
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
33
Page 16
50
30
55
Included
with part# 40
23
27
56
47
31
39
41
58
49
40
42
44
38
59
5
4
37
34
16
29
25
10
36
32
45
15
33
12
22A
22
26
26A
1
6
2
46
13
48
8
11
21
3
28
18
Electric Start Only
20 20A
19
17
Page 17
REFERENCE # PART DESCRIPTION PART #
1 HEATER BOX ASSY 532424932
2 SHIELD, HEATER BOX 532424934
3 SNOW MUFFLER ASSY 532424937
4 SNOW FUEL TANK ASSY 532424938
5 OVERSIZED FUEL TANK CAP (CLICK STYLE) 532424942
6 SNOW CARBURETOR ASSY (INCLUDES BRACKET, SPACER, AND NUTS) 532424944
7 SNOW CHOKE LEVER, CARBURETOR (NOT SHOWN) 532424947
8 FUEL PRIMER BULB WITH HOSE 532424949
10 ELECTRIC STARTER ASSY 532424953
11 KEY SWITCH ASSY 532424954
12 CDI BOX 532424955
13 ON/OFF SWITCH 532424957
15 PLASTIC THROTTLE/CHOKE HANDLE (RED) 532424947
16 GOVERNOR LINKAGE SHIELD PLATE 532424960
17 SNOW RECOIL STARTER ASSY (HEX STYLE - BLACK & INCLUDES SCREWS) 532424962
18 STARTER CUP SMALL 532424966
19 SNOW STARTER GRIP 532424968
20 BLOWER HOUSING ASSEMBLY ELECTRIC START - SNOW (BLACK & INCLUDES SCREWS) 532424971
20A BLOWER HOUSING ASSEMBLY ELECTRIC START - SNOW (BLACK) 532429230
21 SHIELD, CYLINDER 532424973
22 SHIELD, FLYWHEEL 532424975
22A SHIELD, FLYWHEEL - MANUAL START 532429596
23 VALVE COVER (INCLUDES SCREWS) 532420580
25 FUEL PETCOCK 532429597
26 ELECTRIC START FLYWHEEL ASSY 532424235
26A MANUAL START FLYWHEEL ASSY 532429236
27 HIGH OIL FILL TUBE ASSY 532424969
28 FLYWHEEL FAN 532420586
29 IGNITION COIL ASSY 532420595
30 CRANKCASE COVER ASSY (INCLUDES SCREWS) 532420606
31 NON REMOVABLE PLUG 532429598
32 CHARGING COIL DC 532424959
33 ELECTRIC STARTER BRACKET 532429244
34 SPARK PLUG BOOT 532429246
36 GOVERNOR ARM ASSY 532420601
37 GOVERNOR SHAFT 532420602
38 GOVERNOR GEAR ASSY 532429251
38A THROTTLE CONTROL ASM (NOT SHOWN) 532429251
39 CAMSHAFT 532420584
40 CYLINDER HEAD ASSY (INCLUDES SCREWS) 532420578
41 SPARK PLUG 532424939
42 CDI BOX BRACKET 532424936
44 PISTON AND ROD ASSY 532420582
45 SPEED CONTROL BRACKET 532429259
46 VAPOR SHIELD 532429260
47 SEAL KIT 532429599
48 WIRE HARNESS 532429262
49 CRANKSHAFT 532429263
50 GASKET KIT 532429601
54 208CC SHORT BLOCK 532429647
55 ROCKER ARM KIT 532429691
56 PUSH ROD KIT 532420579
58 FUEL HOSE KIT 532432144
59 EXTENDED OIL DRAIN TUBE 532432686
CYLINDER SERVICE KIT 532424970
CARB STUDS & COUPLINGS KIT (NOT SHOWN) 532424951
208CC COMPLETE ENGINE 532428594
REWIND DECAL 532428713
HUSQVARNA CROWN DECAL 532428676
AIR FILTER ASSY PAPER - CALIFORNIA 532432714
FILTER ELEMENT, PANEL PAPER 532432715
50 STATE HUSQ MUFFLER KIT 532432716
CALIFORNIA TANK SERVICE KIT 532432717
CARBON CANISTER 532432718
CALIFORNIA FUEL TANK CAP SERVICE KIT 532432719
OIL DRAIN TUBE 532432686
OIL PLUG 532435495
FUEL PETCOCK 532429597
NON REMOVABLE PLUG 532429598
ENGINE BOLT KIT 532432689
RECOIL BOLT KIT 532432688
208cc SERVICE KIT BREAKDOWN
Page 18
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
CHASSIS / ENGINE / PULLEYS
23
22
24
11
14
21
20
13
12
10
14
21
20
14
15
6
7
8
01.21.003-C
19
18
17
16
5
4
3
9
1
2
KEY PART
NO. NO. DESCRIPTION
1 408007 IMPELLER BELT
2 419744 TRACTION BELT
3 423723X431 IDLER ARM BRACKET
4 180523 IDLER PULLEY
5 426589 NUT 5/16-18
6 74780524 SCREW 5/16-18 X 1 .50
7 423990X431 IDLER BRACKET
8 428867 SCREW 5/16-18 X .625
9 424297 SHOULDER BOLT 5/16-18 X .500
10 751153 NUT 5/16-18 NYLOCK
11 187786 TRACTION IDLER ARM
12 180522 TRACTION PULLEY
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
KEY PART
NO. NO. DESCRIPTION
13 74780520 SCREW 5/16-18 X 1 .00
14 59289 WASHER
15 73800500 NUT 5/16-18
16 851084 SCREW 3/8-24 X 1.375
17 400026 WASHER
18 426491 PULLEY ENG IMPELLER
19 426490 PULLEY ENG TRACTION
20 74610516 SCREW 5/16-18 X 1 .00
21 10040500 LOCKWASHER 5/16
22 155452 BELT GUIDE
23 11050500 LOCKWASHER 5/16
24 175331 IDLER BUSHING
34
Page 19
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
WHEELS
KEY PART
NO. NO. DESCRIPTION
1
1 432331X421 WHEEL ASSEMBLY LH
2 432332X421 WHEEL ASSEMBLY RH
2
01.06.018-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
35
Page 20
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
BAG OF PARTS
3
5
4
2
1
01.14.004-B
7
6
1
01.14.009-A
KEY PART
NO. NO. DESCRIPTION
1 198563 POWER CORD
2 169675 RETAINER PIN
3 180684X008 WRENCH
4 73800600 LOCKNUT 3/8−16
5 19131316 WASHER 3/8
6 192090 SHEAR BOLT 1/4−20 X 1−3/4
7 73800400 LOCKNUT 1/4−20
KEY PART
NO. NO. DESCRIPTION
1 422663 SAFETY IGNITION KEY
1
1
3
4
4
01.14.012-A
2
2
KEY PART
NO. NO. DESCRIPTION
1 180445 SHIFTER ROD TOP
2 187716 SHIFTER ROD BOTTOM
3 72270505 CARRIAGE BOLT 5/16-18 X .75
4 155377 NUT 5/16-18
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
36
Page 21
REPAIR PARTS SNOW THROWER - - MODEL NUMBER MC627ES (96192004100)
DECALS
1
4
9
6
11
1
3
KEY PART
NO. NO. DESCRIPTION
1 181037 DECAL, DANGER
3 181035 DECAL, DANGER, DEFLECTOR
4 181042 DECAL, DANGER
6 181033 DECAL, INSTRUCTION
9 429591 DECAL, CON RT SPD/LEV/PWST
11 428716 DECAL, CON LT WD/DEF
- - 435887 OWNER’S MANUAL, ENGLISH
- - 435888 OWNER’S MANUAL, FRENCH
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
37
Page 22
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or
replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due
to materials or workmanship. This Warranty is subject to the following limitations and exclusions.
1. This warranty does not apply to the engine, transaxle/transmission components, battery (except as noted below) or components parts thereof. Please refer to the applicable manufacturer's warranty on these items.
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the pur chaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser unless such return is requested by the manufacturer.
3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find
to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the
Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must
be maintained in accordance with the instructions furnished.
4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original
purchase.
5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and main tained in ac cor dance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.
6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, stan dard
hardware and normal maintenance.
7. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact:
HOP
Outdoor Products Customer Service Dept.
9335 Harris Corners Parkway
Charlotte, NC 28269 USA
giving the model number, serial number and date of purchase of your product and the name and address of the authorized
dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WAR RAN TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which
vary from locale to locale.
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
In Canada contact:
HOP
5855 Terry Fox Way
Mississauga, Ontario
L5V 3E4
435887 05.19.10 TH Printed in the U.S.A.
Loading...