GB
FR
DE
ES
INSTRUCTION MANUAL
IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference.
MANUEL D’INSTRUCTIONS
RENSEIGNEMENTS IMPORTANTS: Avant d’utiliser cet appareil, veuillez lire
atentivement les instructions et assurez--vous de les avoir comprises. Conservez les instructions pour référence ultérieure.
BETRIEBSANWEISUNG
WICHTIGE INFORMATION: Lesen Sie diese Hinweise zur Handhabung des
Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen verstanden haben und gut aufbewahren.
MANUAL DE INSTRUCCIONES
INFORMACIÓN IMPORTANTE: Lea atentamente las instrucciones y asegúrese de entenderlas antes de utilizar esta aparato. Conserve las instrucciones para la referencia en el futuro.
115154526 Rev. 2 1/31/10 BRW
TABLE OF CONTENTS
Identification (What is What?) |
2 |
Service & Adjustments |
13 |
|
Identification of Symbols |
3 |
Storage |
15 |
|
Safety Rules |
3 |
|||
Troubleshooting Table |
16 |
|||
Assembly |
5 |
|||
Declaration of Conformity |
17 |
|||
Operation |
9 |
|||
|
|
|||
Maintenance |
12 |
Technical Data |
18 |
IDENTIFICATION (WHAT IS WHAT?)
3
7
4
9
|
11 |
|
|
|
|
|
|
|
|
|
|
|
|
18 |
|
20 |
|
15 |
|
|
|
|
||
|
|
|
|
|
21 |
|
22 |
|
|
|
|
|
|
|
1. |
Fuel tank |
12. |
Throttle trigger |
|
2. |
Handlebar |
13. |
Throttle lock--out |
|
3. |
ON/STOP (I/0) switch |
14. |
Starter handle |
|
4. |
Throttle cable clip |
15. |
Fuel cap |
|
5. |
Shoulder harness clamp |
16. |
Primer bulb |
|
6. |
Shoulder harness |
17. |
Start lever |
|
7. |
Trimmer head |
18. |
Muffler |
|
8. |
Line limiter blade |
19. |
Wrench |
|
9. |
Combination shield |
20. |
Hex wrench |
|
10. |
Shaft |
21. |
Transport guard |
|
11. |
Blade |
22. |
Instruction manual |
|
2
IDENTIFICATION OF SYMBOLS
A. |
|
D. |
|
F. |
|
I. |
|
|
|
|
|
|
|||||
B. |
|
|
E. |
|
G. |
|
J. |
|
|
|
|
|
|
||||
|
|
|
|
|
||||
C. |
|
|
|
|
H. |
|
K. |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
A. WARNING! This brushcutter can be dangerous! Careless or improper use can cause serious or even fatal injury.
B.Read and understand the instruction manual before using the brushcutter.
C.Always use:
Ear protection, eye protection, head protection, boots, and gloves.
D.DANGER! Blade can thrust violently away from material it does not cut. Blade thrust
can cause amputation of arms or legs. Keep people and animals 15 meters away. WARNING! Blade/trimmer line can throw objects violently. You and others can be
blinded or injured. Always wear eye protection and leg protection.
F.The operator of the machine must insure that no one comes within a 15 meter radius while working. When several operators are working within the same area a safety distance of at least 15 meters must be observed.
G.Use unleaded or quality leaded petrol and two--stroke oil mixed at a ratio of 2.5%.
H.Handlebar to be positioned only below the arrow.
I.Engine ON/STOP (I/0) Switch.
J.Guaranteed sound power level according to Directive 2000/14/EC
K.Maximum rotational frequency of the spindle, rpm
SAFETY RULES
WARNING: When using gardening
appliances, basic safety precautions should always be followed to reduce the risk of fire and serious injury. Read and follow all instructions.
DANGER: This power tool can be dan-
gerous! This unit can cause serious injury including amputation or blindness to the operator and others. The warnings and safety instructions in this manual must be followed to provide reasonable safety and efficiency in using the unit. The operator is responsible for following the warnings and instructions in this manual and on the unit. Read the entire instruction manual before assembling and using the unit! Restrict the
use of this unit to persons who read, understand, and follow the warnings and instructions in this manual and on the unit. Never allow children to operate this unit.
INSTRUCTION |
SAFETY INFORMATION |
MANUAL |
ON THE UNIT |
DANGER: Blade can thrust violently
away from material it does not cut. Blade thrust can cause amputation of arms or legs. Keep people and animals 15 meters away.
WARNING: Blade/trimmer line can
throw objects violently. You and others can be
blinded or injured. Wear safety glasses and leg protection.
3
WARNING: Hazard zone for thrown
objects. Blade/Trimmer line can throw objects violently. Others can be blinded or injured. Keep people and animals 15 meters away.
Hazard Zone
WARNING: Do not use trimmer head as a fastening device for the blade.
WARNING: The blade continues to
spin after the throttle is released or, engine is turned off. The coasting blade can throw objects or seriously cut if accidentally touched. Stop the blade by contacting the right hand side of the
coasting blade with material already cut.
Stop coasting blade by contact with cut material.
OPERATOR SAFETY
WARNING: This machine produces
an electromagnetic field during operation. Under some circumstances, this field may interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this machine.
S Dress properly. Always wear safety glasses or similar eye protection when operating, or performing maintenance, on your unit (safety glasses are available). Eye protection should be marked Z87.
S Always wear a helmet if the trees to be cleared are taller than 2 meters.
S Always wear face or dust mask if operation is dusty.
S Always wear heavy, long pants, long sleeves, boots, and gloves. Wearing safety leg guards is recommended.
S Always wear foot protection. Do not go barefoot or wear sandals. Stay clear of blade/spinning line.
SSecure hair above shoulder length. Secure or remove loose clothing or clothing with loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.
SBeing fully covered also helps protect you from debris and pieces of toxic plants
thrown by spinning line.
SStay alert. Do not operate this unit when you are tired, ill, upset or under the influence of alcohol, drugs, or medication. Watch what you are doing; use common sense.
SWear hearing protection. Long or continuous exposure to high noise levels may
cause permanent hearing impairment.
SNever start or run inside a closed room or building. Breathing exhaust fumes can kill.
S Keep handles free of oil and fuel.
SAlways use the handlebar and a properly adjusted shoulder harness with a blade (see ASSEMBLY).
UNIT / MAINTENANCE SAFETY
WARNING: Stop unit and disconnect
the spark plug before performing maintenance (except carburetor adjustments).
SThrow away blades that are bent, warped, cracked, broken, or damaged in any other way. Replace trimmer head parts that are cracked, chipped, broken, or damaged in any other way before using the unit.
S Maintain unit according to recommended procedures. Keep blade sharp. Keep cutting line at the proper length.
S Use only 2,4 mm diameter McCulloch brand replacement line. Never use wire, rope, string, etc.
S Install required shield properly before using the unit.
SUse only specified blade or trimmer head; make sure it is properly installed and securely fastened.
S Never start engine with clutch shroud removed. The clutch can fly off and cause serious injury.
SBe sure blade or trimmer head stops turning when engine idles.
SMake carburetor adjustments with the lower end supported to prevent blade or trimmer line from contacting any object. Hold unit by hand; do not use the shoulder harness for support.
4
SKeep others away when making carburetor adjustments.
SUse only recommended McCulloch accessories and replacement parts.
SHave all maintenance and service not explained in this manual performed by your authorized service dealer.
FUEL SAFETY
S Mix and pour fuel outdoors.
S Keep away from sparks or flames. S Use a container approved for fuel.
SDo not smoke or allow smoking near fuel or the unit.
S Avoid spilling fuel or oil. Wipe up all fuel spills.
SMove at least 3 meters away from fueling site before starting engine.
S Stop engine and allow to cool before removing fuel cap.
SAlways store petrol in a container approved for flammable liquids.
CUTTING SAFETY
WARNING: Inspect the area to be cut
before each use. Remove objects (rocks, broken glass, nails, wire, string, etc.) which can be thrown or become entangled in the blade or trimmer head.
S Keep others including children, animals, bystanders, and helpers at least 50 feet (15 meters) away. Stop engine immediately if you are approached.
S Always keep engine on the right--hand side
of your body.
S Hold the unit firmly with both hands.
S Keep firm footing and balance. Do not overreach.
S Keep blade or trimmer head below waist level. Do not raise engine above your waist.
SKeep all parts of your body away from blade, trimmer head, and muffler when engine is running. A hot muffler can cause serious burns.
SCut from your left to your right. Cutting on right side of the shield will throw debris
away from the operator.
S Use only in daylight or good artificial light. S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
SAllow the engine to cool; secure unit before storing or transporting in vehicle.
SEmpty fuel tank before storing or transporting the unit. Use up fuel left in the carburetor by starting engine and letting it run until it stops.
SStore unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.
S Store unit so line limiter cannot accidentally cause injury. Unit can be hung by the shaft.
S Always install transport guard on blade before transporting or strorage.
S Store the unit out of the reach of children. S Secure the machine during transport.
SPECIAL NOTICE: Exposure to vibrations
through prolonged use of petrol powered hand tools could cause blood vessel or nerve dam-
age in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration
system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.
ASSEMBLY
CARTON CONTENTS
Check carton contents against the following list: S Brushcutter
S Blade
S Cupped washer
S Large nut for installing blade S Trimmer head
S Combination shield S Bolt
S Handlebar
S Handlebar bracket cover
S Handlebar bracket cover screws (2) S Upper shoulder harness clamp
S Lower shoulder harness clamp
S Shoulder harness clamp screws (2) S Shoulder harness
S Hex wrench S Wrench
S Transport guard S Throttle cable clip
WARNING: Always stop unit and dis-
connect spark plug before performing any assembly procedures.
WARNING: If received assembled,
repeat all steps to ensure your unit is properly assembled and all fasteners are secure. Examine parts for damage. Do not use damaged parts.
It is normal for the fuel filter to rattle in the empty
fuel tank.
Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.
TOOLS REQUIRED
S Hex wrench (provided) S Adjustable wrench
S Phillips screwdriver
5
ATTACHING THE HANDLEBAR
DANGER: To avoid serious injury, the barrier portion of the handlebar must be installed
as shown to provide a barrier between operator and the spinning blade.
1.Remove the screw at the rear of the throttle handle.
2.Slide the throttle handle onto the right side of the handlebar (see illustration).
3.Align the screw hole in the throttle handle with the hole in the handlebar.
4.Refit the screw in the hole in the rear of the throttle handle.
5.Screw the screw through the handle and handlebar. Tighten the screw.
6.Fit the mounting components as shown.
2.Position the lower shoulder harness clamp under the shaft and align the upper and lower clamp screw holes. Clamp must be fittle above the arrow on the shaft (see illustration above).
NOTE: Fit throttle wire in groove of lower harness clamp before tightening screws.
3.Insert two screws into the screw holes.
4.Secure shoulder harness clamp by tightening screws with a hex wrench.
SHOULDER HARNESS ADJUSTMENT
At the front of the shoulder harness is an easily accessible quick release. Use the quick release
in any emergency situation that requires you to free yourself from the machine and harness.
1.Put on the harness. Adjust the harness for the best working position.
2.Tension the side straps so that the weight is evenly distributed across both shoulders.
7.The handlebar mounting must be fitted between the arrows on the shaft.
8.Tighten the screws with a hex wrench.
ASSEMBLY OF SHOULDER HARNESS
WARNING: When using a brushcut-
ter, it must always be hooked securely to the shoulder harness. Otherwise, you will be un-
able to safely control the brushcutter. This can result in injury to yourself or others. Proper shoulder harness and handlebar adjustments must be made with the engine completely stopped before using unit. A well--adjusted shoulder harness and machine makes work much easier.
ATTACHING SHOULDER HARNESS CLAMP (if not already attached)
1.Place the upper shoulder harness clamp over the shaft.
NOTE: It may be necessary to relocate the shoulder harness clamp on the shaft for proper balancing of unit.
SHOULDER HARNESS
ADJUSTMENT
FOR BALANCE
15 cm |
|
|
|
below |
|
|
10 -- 30 cm |
waist |
|
|
above |
|
|
76 cm |
ground |
|
|
|
|
6
Loading...