McCulloch Cabrio 115249726 User Manual

INSTRUCTION MA NUAL

IMPORTANT INFORMATION

sure you understand them before using this unit. Retain these instructions for future reference.

: Please read these instructions carefully and make

MANUEL D’INSTRUCTIONS

RENSEIGNEMENTS IMPORTANTS:

atentivement les instructions et assurez- -vous de les avoir comprises. Conservez les instructions pour référence ultérieure.

Avant d’utiliser cet appareil, veuillez lire

BETRIEBSANWEISUNG

WICHTIGE INFORMATI ON:

Geräts aufmerksam durch. Verwenden Sie es erst, wenn Sie sicher sind, daß Sie alle Anweisungen verstanden haben und gut aufbewahren.

Lesen Sie diese Hinweise zur Handhabung des

MANUAL DE INSTRUCCIONES

INFORMACIÓN IMPORTANTE:

asegúrese de entenderlas antes de utilizar esta aparato. Conserve las instrucciones para la referencia en el futuro.

Lea atentamente las instrucciones y

115249726 Rev. 1 9/15/09 BRW

TABLE OF CONTENTS

Identification (What is What?) 2 Identification of Symbols 3 Safety Rules 3 Assembly 5 Operation 9 Maintenance 16

IDENTIFICATION (WHAT IS WHAT?)

1. Fuel tank

2. Loop handle

3. ON/STOP switch

4. Shoulder strap clamp

5. Shoulder strap

6. Trimmer head

7. Line limiter blade

8. Shield

9. Shaft

10. J--handle

11. Blade

12. Coupler

13. Throttle trigger

14. Throttle lock--out

15. Starter handle

16. Fuel cap

17. Primer bulb

18. Start lever

19. Muffler

20. Wrench

21. Hex wrench

22. Instruction manual

23. Transport guard

Service & Adjustments 16 Storage 18 Troubleshooting Table 19 Declaration of Conformity 20 Technical Data 21

IDENTIFICATION OF SYMBOLS

WARNING! This brushcutter can be dangerous! Careless or improper use can

cause serious or even fatal injury. B. Read and understand the instruction manual before using the brushcutter. C. Always use:

Ear protection, eye protection, head protection, boots, and gloves.

D. DANGER! Blade can thrust violently away from materialit doesnot cut. Blade thrust

can cause amputation of arms or legs. Keep people and animals 15 meters away.

E. WARNING! Blade/trimmer line can throw objects violently. You and others can be

blinded or injured. Always wear eye protection and leg protection. F. The operator of the machine must insure that no one comes within a 15 meter radius

while working. When several operators are working within the same area a safety dis-

tance of at least 15 meters must be observed. G. Use unleaded or quality leaded petrol and two--stroke oil mixed at a ratio of 2.5%. H. Assist handle to be positioned only below the arrow. I. Engine ON/STOP Switch. J. Guaranteed sound power level according to Directive 2000/14/EC

K. Maximum rotational frequency of the spindle, rpm

SAFETY RULES

WARNING: When using gardening

appliances, basic safety precautions should always be followed to reduce the risk of fire and serious injury. Read and follow all instructions.

DANGER: This power tool can be dan-

gerous! This unit can cause serious injury including amputation or blindness to the operator and others. The warnings and safety instructions in this manual must be followed to provide reasonable safety and efficiency in using the unit. Theoperator is responsible for following the warnings and instructions in this manual and on the unit. Read the entire instruction manual before assembling and using the unit! Restrict the use of this unit to persons who read, understand, and follow the warnings and instructions in this manual and on the unit. Never allow children to operate this unit.

INSTRUCTION MANUAL

DANGER: Blade can thrust violently

away from material it does not cut. Blade thrust can cause amputation of arms or legs. Keep people and animals 15 meters away.

SAFETY INFORMATION ON THE UNIT

WARNING: Blade/trimmer line can

throw objects violently.Youand others canbe blinded or injured. Wear safety glasses and leg protection.

WARNING: Hazard zone for thrown

objects. Blade/Trimmerline can throw objects violently. Others can be blinded or injured. Keep people and animals 15 meters away.

Hazard Zone

WARNING: Do not use trimmer head

as a fastening device for the blade.

WARNING: The blade continues to

spin after the throttle is released or, engine is turned off. The coasting blade can throw objects or seriously cut if accidentally touched. Stop the blade by contacting the right hand side of the coasting blade with material already cut.

Stop coasting blade by contact with cut material.

OPERATOR SAFETY

S Dress properly. Always wear safety

glasses or similar eye protection when operating, or performing maintenance, on your unit (safety glasses are available). Eye protection should be marked Z87.

S Always wear a helmet if the trees to be

cleared are taller than 2 meters.

S Always wear face or dust mask if operation

is dusty.

S Always wear heavy, long pants, long

sleeves, boots, and gloves. Wearing safety leg guards is recommended.

S Always wear foot protection. Do not go

barefoot or wear sandals. Stay clear of blade/spinning line.

S Secure hair above shoulderlength. Secure

or remove loose clothing or clothing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts.

S Being fully covered also helps protect you

from debris and pieces of toxic plants thrown by spinning line.

S Stay alert. Do not operate this unit when you

are tired, ill, upset or under the influence of alcohol, drugs, or medication. Watch what you are doing; use common sense.

S Wear hearing protection. Long or continu-

ous exposure to high noise levels may cause permanent hearing impairment.

S Never start or run inside a closed room or

building. Breathing exhaust fumes can kill.

S Keep handles free of oil and fuel. S Always use the handlebar and a properly

adjusted shoulder strap with a blade (see ASSEMBLY).

UNIT / MAINTENANCE SAFETY

WARNING: Stop unit and disconnect

the spark plug before performing maintenance (except carburetor adjustments). S Throw away blades that are bent, warped,

cracked, broken, or damaged in any other way. Replace trimmer head parts that are cracked, chipped, broken, or damaged in any other way before using the unit.

S Maintain unit according to recommended

procedures. Keep blade sharp. Keep cutting line at the proper length.

S Use only 2,4 mm diameter McCulloch

brand replacement line. Never use wire, rope, string, etc.

S Install required shield properly before using

theunit.Usethemetalshieldforallmetal blade use. Use the plastic shield for all line trimmer use.

S Use only specified blade or trimmer head;

make sure it is properly installed and securely fastened.

S Never start engine with clutch shroud re-

moved. Theclutch canfly off andcause serious injury.

S Be sure blade ortrimmer headstops turning

when engine idles.

S Make carburetor adjustments with the lower

end supported to prevent blade or trimmer line from contacting any object. Hold unit by hand; do not use the shoulder strap for support.

S Keep othersaway when makingc ar bure-

tor adjustments.

S Use only recommended McCulloch accesso-

ries and replacement parts.

S Have all maintenance and service not ex-

plained in this manual performed by your authorized service dealer.

FUEL SAFETY

S Mix and pour fuel outdoors. S Keep away from sparks or flames. S Use a container approved for fuel. S Do not smoke orallow smoking near fuelor

the unit.

S Avoid spilling fuel or oil. Wipe up all fuel spills. S Move at least 3 meters away from fueling

site before starting engine.

S Stop engine and allow to cool before re-

moving fuel cap.

S Always store petrol in a container approved

for flammable liquids.

CUTTING SAFETY

WARNING: Inspect the area to be cut

before each use. Remove objects (rocks, broken glass, nails, wire, string, etc.) which can be thrown or become entangled in the blade or trimmer head. S Keep others including children, animals,

bystanders, and helpers at least 15 meters away. Stop engine immediately if you are approached.

S Always keep engine on the right--hand side

of your body.

S Hold the unit firmly with both hands. S Keep firm footing and balance. Do not

overreach.

S Keep blade or trimmer head below waist

level. Do not raise engine above your waist.

S Keep all parts of your body away from

blade, trimmer head, and muffler when engine is running. A hot muffler can cause serious burns.

S Cut from your left to your right. Cutting on

right side of the shield will throw debris away from the operator.

S Use only in daylight or good artificial light. S Use only for jobs explained in this manual.

TRANSPORTING AND STORAGE

S Allow the engine to cool; secure unit before

storing or transporting in vehicle.

S Empty fuel tank before storing or transporting

the unit. Use up fuel left in the carburetor by starting engine and letting it run until it stops.

S Store unit andfuel in an area where fuelva-

pors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

S Store unitso line limiter cannot accidentally

cause injury. Unit can be hung by the shaft.

S Always install transport guard on blade be-

fore transporting or strorage.

S Store the unit out of the reach of children.

SPECIAL NOTICE: Exposure to vibra-

tions through prolonged use of petrol powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather hasbeen linkedto bloodvessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use ofthis tool and seek medical attention. An anti-vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool.

ASSEMBLY

CARTON CONTENTS

Check carton contents against the following list:

S Powerhead S Trimmer attachment

S Trimmer head S Blade S Blade shield S Blade shield screws (4) S Cupped washer S Large nut for installing blade S Plastic shield S Nut(screwedontoplasticshield) S Loop handle

S Securing plate

S Bolt

S Wing nut S J- -handle

S Screws (2) S Hex wrench S Wrench S Shoulder strap S Transport guard

WARNING: Always stop unit anddis-

connect spark plugbefore performing anyassembly procedures.

WARNING: If received assembled,

repeat allsteps to ensure your unit is properly assembled and all fasteners are secure. Examine parts for damage. Do not use damaged parts. It is normal for the fuel filter to rattle in the empty fuel tank. Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.

TOOLS REQUIRED

S Hex wrench (provided) S Adjustable wrench S Phillips screwdriver

INSTALLING TRIMMER ATTACHMENT

WARNING: When installing attach-

ment, placethe unit on a flat surface forstability.

1. Loosen the coupler by turning the knob

counterclockwise.

Coupler

ATTACHING THE HANDLE

DANGER: T o avoid serious injury, the

barrier portion of the handle must be installed as shown to provide a barrier between operator and the spinning blade.

1. Position the loop handle on the shaft. Note that the handle must be mounted between the arrows on the shaft.

Shipping protector

2. Remove shipping protector from coupler.

3. Remove the shaft cap from the attachment (if present).

4. Position locking/release button of attachment into guide recess of coupler.

5. Push the attachment into the coupler until the locking/release button snaps into the primary hole.

6. Before using the unit, tighten the knob securely by turning clockwise.

Coupler

Upper

Shaft

LOOSEN

Knob

TIGHTEN

Primary Hole

Guide Recess

Locking/ Release

Button

Attachment

WARNING: Make sure the locking/

release button is locked in the primary hole and the knob is securely tightened before operating the unit. All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to serious injury or damage to the unit.

Locking/Release Button in Primary Hole

For optional attachments, see the ASSEMBLY section of the applicable attachment instruction manual.

2. Install the bolt, securing plate and wing nut as shown in the illustration.

3. Make a final adjustment of the handle toa comfortable working position. Tighten the wing nut.

ASSEMBLY OF SHOULDER STRAP

Proper shoulder strap and handlebar adjustments must be made with the engine completely stopped before using unit.

1. Insert your rightarm andhead throughthe shoulder strap and allow it to rest on your left shoulder. Make sure the hook is to the right side of your waist.

NOTE: A one-half twist is built in the shoul-

der strap to allow the strap to rest flat on the shoulder.

2. Adjust the strap, allowing the hook to be about 15 cm below the waist.

3. Fasten the strap hook to the clamp located between the trigger handle and the handlebar clamp base and lift the tool to theoperating position.

4. Try on shoulderstrap and adjust for fit and balance before starting the engine or beginning a cutting operation.

NOTE: It may be necessary to relocate the

shoulder strap clamp on the shaft for proper balancing of unit.

TO RELOCATE SHOULDER STRAP CLAMP:

1. Loosen and remove both clamp screws.

2. Place the upper shoulder strap clamp over the shaft.

3. Position the lower shoulder strap clamp under the shaft and align the upper and lower clamp screw holes.

Upper shoulder strap clamp

Lower shoulder strap clamp

4. Insert two screws into the screw holes.

5. Secure shoulder strap clamp by tightening screws with a hex wrench.

15 cm below waist

Screws

HARNESS

ADJUSTMENT

FOR BALANCE

76 cm

10 -- 30 cm

above

ground

ASSEMBLY INFORMATION -TRIMMER HE AD

TRIMMER HEAD

NOTE: Remove the blade andmetal shield be-

fore attaching the plastic shield and trimmer head. T o remove blade, align hole in the dust cup with the hole in theside of the gearbox by rotating the blade. Insert a small screwdriver into alignedholes. This will ke ep the shaftfrom turning while loosening the blade nut. Remove blade nut by turning clockwise. Remove the screwdriver. Remove both washers and blade. T o remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INST ALLATION OF THE METALBLADE forillustrations. Be sure tostore all parts and instructions for future use.

ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD

WARNING: The shield must be prop-

erly installed. The shield provides partial protection to the operator and others from the risk of thrown objects, and is equipped with a line limiter blade which cuts excess line tothe proper length. The line limiter blade (on underside of shield) is sharp and can cut you.

1. Remove nut from shield.

2. Insert bracket into slot on shield.

3. Pivot shield until bolt passes through hole in bracket.

CONFIGURING YOUR UNIT

Youcan configure your unit using a cutting head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1 cm in diameter. T o assemble your unit, go to the section for the desired configuration and follow the instructions.

Bracket

Shield

Slot

4. Reinstall nut and tighten securely with wrench (provided).

+ 14 hidden pages