QUBFour
MBQuart products are designed and engineered in the USA by
847-540-7700
www.maxxsonics.com
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifi cations not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
QUBFour
BluetoothTM Speaker
CONTENTS
WARRANTY
Page 3
6-7
10
11
Important Safety Instructions
Controls
4
Charging
5
Bluetooth Connection
Auxiliary Input
8
Receiving and Making Calls
9
Specifi cations
Warranty
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during
the warranty period. Components that prove to be defective in materials or workmanship
must be returned to the original authorized Maxxsonics USA Inc. retailer from where it
was purchased. A photocopy of the original receipt must accompany the product being
returned. This warranty is limited to defective parts and specifi cally excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
The Bluetooth™ word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and
any use of such marks by MB Quart is under license.
11
SPECIFICATIONS
IMPORTANT SAFETY INSTRUCTIONS
Active Drivers:
Passive Drivers:
Amplifi er Power:
Frequency Response:
Battery Type:
Battery Capacity:
10
2 - 50mm (1.97 Inches)
1
12 Watts
60Hz - 18KHz
Lithium-ion Polymer
1050mAh
Play Time:
Recharge Time:
Bluetooth Profi les:
Bluetooth Range:
Dimensions:
Weight:
10 to 12 Hours
3.0 Hours
HFP-A2DP/ARVCP
20 meters in open space
85 x 160 x 75 (mm)
510 grams
• Read, follow and keep these instructions.
• Do not use this product near water or wet surfaces.
• Clean only with a dry cloth.
• Do not expose to extreme high or low temperatures.
• Only use the supplied cables for charging and playback.
3
CONTROLS
Function Button
Pairing LED
Volume Up \ Down
Power Switch
4
RECEIVING AND MAKING CALLS
Your speaker will allow you to make hands free calls provided your phone is connected via Bluetooth.
The AUX connection cannot be used for this function.
To make a call: Use the phone as normal, select the Bluetooth speaker when prompted.
To receive a call: Either push the FUNCTION button on the top of the speaker or answer the call with
the phone making sure to select the Bluetooth speaker when prompted.
Ending a call: Either push the FUNCTION button on the top of the speaker or hang up using the
phone as you normally would.
Rejecting a call: Push the FUNCTION button for three seconds.
To switch from the Bluetooth speaker to the phone during a call: Press the FUNCTION button twice.
9
AUXILIARY INPUT CONNECTION
Insert the supplied 3.5mm cable
into the speaker’s AUX input.
Connect the other end to the
output of your source device.
The power switch light will turn off.
You can now play your content.
The Bluetooth will be disabled
anytime a 3.5mm cable is inserted
8
into the AUX input.
CHARGING
The fi rst time you use
your Bluetooth speaker,
please charge it for at
least 3 hours. During the
fi rst charge, do not turn
on the device.
Using the supplied charge cable
connect to a 110V wall outlet.
While charging, the power switch
on the side of the unit will turn
red.
When fully charged, the power
switch light will turn off.
After the fi rst charge, you can play
and charge at the same time.
5
BLUETOOTH CONNECTION
TROUBLE CONNECTING?
When the speaker is turned on, you should hear a voice prompt and the pairing LED on
the front of the speaker will fl ash indicating that pairing mode is activated and it is search-
ing for a Bluetooth source.
Go to the Bluetooth menu of your source device and connect to QUBFour from the list of
devices. If asked for a code, enter 0000.
Once the connection is achieved, the pairing LED will stop fl ashing and the speaker will
emit two short beeps.
You are now connected and can play from your source.
6
Make sure that no other source in range is connected. Only one connection can be made
at a time, The speaker may automatically connect to a source it has been paired with in the
past.
Turn off the speaker, then on again. Try pairing again.
Make sure the source is Bluetooth compatible and that the Bluetooth is activated.
Review your source device documentation for Bluetooth pairing instructions.
7
Loading...