MBM Corporation 430 EP User Manual

Download

Page 1

EBA • Made in Germany

Document Shredders

EBA 430 E EBA 430 EP

Operating Instructions

Trimmers and Guillotines

• EBA Krug & Priester • 72336 Balingen • Germany • www.eba.de •

Printed in Germany • EBA 04/2002 • DPrinted in Germany • EBA 04/2002 • D

Page 2

EBA 430 E • EBA 430 EP

Dear customer, Thank you for choosing a paper cutting machine from EBA. With the purchase of this quality product you can be sure you have made a good choice.

Please read these operating instructions before putting the machine into operation and observe the safety regulations.

Read through the operating instructions carefully

Table of contents

Pages

Safety precautions 4 – 11 Installation 12 – 13 Operation 14 – 25 Blade replacement 26 – 34 Maintenance and cleaning 35 – 36 Possible malfunctions 37 – 42 Accessories 43 Manufacturer´s Declaration 45

-2-

-3-

Page 3

EBA 430 E • EBA 430 EP

Children must not operate the machine!

Paper clips or hard material will damage the cutting blade!

The machine must be installed on a sturdy, dry and level floor!

The machine must not be located outside!

Do not cut hard materials or materials which may splinter!

Do not use in the vicinity of inflammable liquids or gases!

-5--4-

Page 4

EBA 430 E • EBA 430 EP

The machine may only be used for cutting paper or similar materials!

Never leave the blade unattended. Do not dismount or transport the blade without protection!

Risk of injury!

This machine is only constructed for "one-man operation"!

Disconnect from the mains before starting any service work or before removing the panels!

Replacement of blade and cutting stick may only be performed when the main switch is switched off!

-7--6-

Page 5

EBA 430 E • EBA 430 EP

All components which may endanger the operator are covered by a guard!

Operating the machine without safety device (front safety guard (A), rear screwed safety guard (B) and panel (C) is forbidden!

The dangerous cutting movement is safeguarded by a movable guard (A) and a safety two-handed control system! (B)

Before working with the machine and after every blade replacement the automatic cut-off function of safety guard (A),(correct if distance between cover and table is < 15 mm) main switch (B) and control panel (C) must be checked.

≤15mm ≤0.59inch

-9--8-

Page 6

EBA 430 E • EBA 430 EP

230 V / 10A min 115 V / 15A min

Protect mains cable against heat, oil and sharp edges!

Connect the power cord to a single phase socket

When not in use for a longer period switch off. (Main switch to "0").

Ensure free access to mains

-11--10-

Page 7

EBA 430 E • EBA 430 EP

Unpack the cabinet (A), (accessories) or stand (B), (accessories) and assemble according to the enclosed separate instructions.

2 strong people are required to lift the machine onto the cabinet or stand. Beware of fingers! Risk of injury!

Only on EBA 430 E

Screw on the backgauge crank (A) and operating handle (B) (found together with tools in the tool set).

Plug into socket.

-12-

-13-

Page 8

EBA 430 E • EBA 430 EP

It is not allowed to operate the machine if the operating and safety instructions have not been understood. Please check the safety devices upon their function and completeness before working with.

• All covers have to be mounted (A).

• The release for cutting is allowed only if

the cover is closed and the two-hand safety device is operated at the same time (B)

• The front cover should not close by itself (otherwise please adjust the hexagonal screw at the right and left(C). (Remove the cover) (D).

We recommend to keep a test result booklet.

Position the main switch to "I" (A). Insert the key for the control system and move it to the right (B). Open the safety guard (C). The machine is now ready for use.

Only EBA 430 EP

Press

S button (D).

(Reference point is driven to).

-14-

-15-

Page 9

EBA 430 E • EBA 430 EP

EBA 430 E

EBA 430 EP

EBA 430 E

The backgauge has to be adjusted by the handle with calibration ring (A). Measurement has to be adjusted from the rear.

EBA 430 EP

The graduation is done manually via the handle with calibration ring (B) or by programming (C) the cutting measurements.

(If Display shows " has to be moved to the right, so the backgauge (E) is moving).

C" the pressure lever (D)

EBA 430 E

EBA 430 EP

EBA 430 E

Measurement is indicated on the back side-lay (A). The fine adjustment is achieved by using the calibration ring (B). The scale is divided in mm (One complete turn corresponds 10 mm = 1 cm).

EBA 430 EP

Measurement is shown in the display of the control device in inches or cm (C).

-17--16-

Page 10

EBA 430 E • EBA 430 EP

Optical cutting line (A) that indicates the exact position of the cut.(Only use when no exact cut is required).

Only for EBA 430 E

Change of measurement through oversight is avoided by pulling out the lever.

Position the paper on the back gauge (A) and side-lay (B). To move paper stacks, please use the stacking angle (C). (Run backgauge to the front for turning the paper stack).

Close the safety guard.

-18-

-19-

Page 11

EBA 430 E • EBA 430 EP

Before every cut the lever must be pushed to the left and tightened with light pressure.

Press both buttons of the two-hand activation (A) simultaneously and keep them pressed until the paper is completely cut.

Operating elements

- Guard front

- Safety two-handed control system

- Overload switch

(Blade drive/Backgauge drive)

- Backgauge control

- Clamping

- Main switch

- Handwheel for backgauge setting

- Key switch

- Backgauge

- Side gauge left

- Display cutting size (cm or inch)

- Select program step down

- Select program step up

- Stop and delete input

Cutting stop or interruption Release one or both buttons (A) of the twohand control.

inch

- Start

- Eject function

- Keypad

- Changeover cm/inch

- Clear program

- Select program

- Enter

- Program number

- Program step

- Specified size

-21--20-

Page 12

EBA 430 E • EBA 430 EP

inch

EBA 430 EP Start machine

• Main switch

for the control panel and turn it to the right. Open the safety Front guard

• Press S button

the rear and searches for the reference position, wait until a measurement of 38,5 cm or 15,16 inch is shown in the display

Warning!

Before storing or cutting a measurement please check if the correct measurement scale (cm or inch) is stored. How to store see below picture on the left.

Dimensions control - cutting to specified dimensions

to position "I", insert the key

➞ backgauge I moves to

• Enter dimension at the numerical key pad

➞ LED "S" X appears.

• Press S button ➞ dimension is approached,

➞ LED "S" disappears.

Dimensions below 9 cm can only be approached with the (When the start button backgauge of 9 cm ➞ measurement 9 cm blinks, now push again the start button, backgauge moves to for example 7 cm).

S button held pressed.

is released, the

moves to a measurement

• Insert paper and move by means of the

stacking angle to the backgauge lay at the left

• Close the safety guard

• Move the pressing lever

slight swing.

to the left by a

and side

• Release the cutting.

Cut according to markings

• Adjust the backgauge with the hand-wheel

to the back.

• Insert paper and move by means of the

stacking angle to the backgauge side-lay

• Turn rotary control

• Close the safety guard

to the right until the marking on the paper to be cut is below the cutting line indicator. The further the rotary control is turned to the right, the faster the backgauge moves. Return of the backgauge is quick by turning the rotary control to the left.

and left

• Move the pressing lever

swing.

to the left by a slight

• Release the cut.

Eject function

z button is kept pressed the backgauge

If the

moves to a measurement of 9 cm (Basic

adjustment) and when released the returns to the measurement last set. If the

z button is released while the

backgauge moves to the front, the backgauge stops and moves back to the measurement which has been set last time.

Cutting activation

Warning!

z button

• Run backgauge to the front for turning the

paper stack.

• Do not interrupt the upward movement of the

blade by performing switching procedures.

• Release blade only when LED "S" has gone

out.

• Close the front guard

• Blade must always be at the top and be

covered by the clamp. Do not touch the blade - risk of injury! (see security information on page 34).

-23--22-

Page 13

EBA 430 E • EBA 430 EP

inch

Programming only EBA 430 EP

This control system enables you to store 9 programs with 9 programmable steps. One step represents one measurement. After entering the program numbers you are able to change between several program steps with the button

r and h.

First figure in display = program number, Second figure = program step. Dimensions below 9 cm can only be approached with the

u“ on the Display ➞ the entered dimension is

„

too low. (Smallest measurement 3,5 cm).

„

o“ on the Display ➞ the entered dimension is

too high. (Largest measurement 38,5 cm). Each program step corresponds to one dimension. The indicated program step can be overwritten at any time. These programs remain stored when the machine is off. Should you change to another dimension unit all programmed measures are converted into the new unit (cm and inch).

Entering a program

• Press p ➞ P appears in the Display.

• 1 ... 9 Enter program number 1...9.

(First figure in Display = program number).

• Enter dimension, or move the backgauge to

the desired measurement with the rotary control.

• g Store the dimension ➞ next program step

appears.

• Enter the next dimension.

(should an ejection be desired before this cut push the eject function are stored now).

• g Store the dimension.

• Should the entered program be required

immediately ➞ Press Press

S again (backgauge moves to the

dimension of the 1st program). Or:

• p + s Escape the program mode.

S button held pressed.

z button, measurement and

S (program is closed).

Eject function

• Set the measurements ➞ push the z

button.

• g Store the dimension.

Backgauge moves in the program for unloading paper to the front and then to the measurement which has been set in the panel.

Cancel a program

• p Press ➞ P appears in the display..

• 1 ... 9 Enter program number 1 ... 9.

• Press c twice.

Each program has to be cancelled separately. Single program steps can only be overwritten.

Deleting the last program step

• Press 0 .

• Press g .

p + s Escape the program mode.

Working with programs

• Press

•

With the button between several program steps. With dimension. With

General

LED "S" blinks ➞ the basic position will appear. LED "S" is off ➞ the actual dimension appears. In the program mode the ejection of paper not possible. The ejection of the paper has to be programmed.

After each cut pressing the button backgauge moves to the next dimension.

Escape the program mode

p ➞ P appears on the display

1 ... 9 Enter Program number 1 ... 9

r and h you are able to change

S the backgauge moves to the indicated

s the backgauge stops.

z is

S the

• Press p ➞ P appears on the display.

• Press s ➞ Escape the program mode.

h and

Program buttons

By means of buttons choice can be reached. (Basic adjustment

r programms

h and r dimension of your

h = 38,5 cm, r = 9 cm).

• p and simultaneously h resp. r ➞ ( h U resp.

r D appears on the display.

• Insert the desired dimension.

• g Store dimension.

Display in cm or inch

• Press i ➞ Display changes between cm

and inch. (See picture left).

Adjust the eject-dimension

The eject dimension is programmed to 29,50 cm. It may be changed as follows:

• Press p Press p + z ➞ e on Display.

• Insert the desired dimension.

• g Store dimension.

• The eject function must be programmed in

the 1 st dimension if the paper stack should be ejected at the end of a program where several cutting processes are made.

-24-

-25-

Page 14

EBA 430 E • EBA 430 EP

If the cutting quality decreases:

• Check the cutting depth (see page 34).

• Check the cutting stick (see page 30).

• Replace or grind the cutting stick

(see page 26-34). The blade may only be grinded by a qualified workshop or from the manufacturer Krug & Priester, D-72336 Balingen.

Danger! Risk of injury

The blade is extremely sharp. Do not dismount or transport the blade without protection. Changing the blade may only be performed by trained staff.

Turn the blade depth adjustment screw to the left until it stops (Screwdriver found in tool set).

Lower the blade by pressing both cutting buttons (1.). Keep one button pressed and turn off the main switch (2.).

-26-

-27-

Page 15

EBA 430 E • EBA 430 EP

Clamping

Blade

The 3 eccentrics are now exposed and should be turned counter clockwise to position "0" with the special wrench (A) (found in tool set). Until the red arrow-like eccentric marking corresponds to the position "0" (B).

Remove the special wrench and turn on the main switch until the blade returns to the home position.

Danger! Do not put main switch on position

"0" whilst blade is moving upwards! The clamp must always overlap the blade! Risk of injury!

Remove the 2 blade screws (1.). Then put the blade changing tool (2.) into place and fasten it to the blade.

The remaining screws should then be removed (1.). Loosening the grips of the blade changing tool lightly (2.) will now allow the blade to be taken downwards out of the machine (3.).

-28-

-29-

Page 16

EBA 430 E • EBA 430 EP

If needed the cutting stick can be turned or exchanged. (The cutting stick can be used eight times).

Danger! Risk of injury!

4-5 mm

0.15-

0.20 inch

Screw the exchange blade to the blade changing tool as follows: (A)

• make sure there is a space ot 4 - 5 mm

or 0.15 - 0.20 inches (B).

• blade must be covered (C).

-30-

Place the blade to be exchanged with the blade changing tool mounted (1.), into the blade carrier and push it up to the top and screw it into place with the grips (2.).

-31-

Page 17

EBA 430 E • EBA 430 EP

Lightly tighten 3 of the 5 blade screws (1.) (with washers), remove the blade changing tool (2.) and lightly tighten the remaining blade screws (with washers) (3.).

Remove all tools and distribute paper along the entire cutting length.

Close the safety guard (1.) Lower the blade by pressing both cutting buttons (2.). Keep one button pressed and turn off the main switch (3.). Open the safety guard (4.). With the special wrench (B) the 3 eccentrics shall be screwed so far down (5.)until the paper is cut along the entire length of the blade (The blade must remain parallel, not too deep into cutting stick).

Turn main switch to position I. (1.) The blade will return to the upper position and the blade screws should be tightened firmly (2.).

-32-

-33-

Page 18

EBA 430 E • EBA 430 EP

Clamping

Blade

Cut a stack of paper to test. If the last sheet has not been cut through move the knob for the adjustment of the blade depth setting (A) to the right (about ½ - ¾ turn if maximum of stacking height is going to be cut - the blade is set lower - do not set it too low, blade will become dull sooner.

Danger! Blade must always be covered by

the pressing bar (see picture below at the left).

Maintenance work may only be performed by trained staff.

Disconnect the mains before starting any service work or before removing the cover.

Oil the backgauge (A) control weekly i.e. grease it. (Use non-resinous oil and grease). Twice a year the remaining 14 grease parts (B) (see picture). To do this switch please bring the main switch to position "0" (E) and move the machine on its left sidfe.

Danger! of tilting!

Remove cover (C) and lower panel (D) (tools in tool set).

• Remove remaining paper

• Grease the machine

• Check the two joining bolts and

pushing bar for wear

• Mount the machine upright

-35--34-

Page 19

EBA 430 E • EBA 430 EP

Safety check

According to § 40 VBG 7i a safety check according to the safety stipulations has to be made every 5 years by a service team authorised through our service department. The carrying-out of such a check has to be attested on the test certificate. A corresponding test label must be visible and affixed to the machine. In Germany such a safety check is regulated and we recommend it for all other

countries, too.

Machine does not function

Machine is plugged in?

-36-

Main switch to position "I"? Control system activated? (Turn key to the right)

-37-

Page 20

EBA 430 E • EBA 430 EP

Machine turns off: EBA 430 E and EBA 430 EP

• Extreme load of machine (cooling phase.

Security switch (A) turns off.

About 1 minute, push the safety button (A).

• Machine blocked

• Blade is dull

Eliminate the disturbance, push the safety

button (A).

EBA 430 EP only: Safety button (B) jumps out.

• Backgauge blocked

Safety button (B) jumps out.

Eliminate disturbance, push the safety

button (B).

Does not cut through the last sheet:

• Turn or turn around the cutting stick (A),

readjust the blade by means of the blade adjusting knob (B)

Poor cutting quality or blade stays in the paper stack.

• change the blade (C) (see page 26-34).

-39--38-

Page 21

EBA 430 E • EBA 430 EP

EBA

"Service"

Motor runs but blade does not move downwards.

• Security brake has been activated!

Inform the service team!

www.EBA.de

service@krug-priester.com

Display illumination off

• Machine is plugged in? (A)

• Main switch on position "I"? (B)

• Key turned to the right ?(C)

• Push in the security button! (D)

• Check the fuse of the buildings’

• electrical installation!

➞➞

➞ "Service"

➞➞

inch

EBA 430 E Cut cannot be made.

• If cover is open:

close it.

• If cover is closed: open and re-close it. (Security check).

EBA 430 EP Cut cannot be made.

• Measurement has not been driven to correctly.

• LED "S"

Push again the Security check of the cover (see above)

• Measurement below 9 cm

Hold the achieved.

• Backgauge shows "

Turn the pressing lever

• Backgauge (pressing lever has been turned to the right). "

C" is in the display

➞ inform service people.

does not turn off.

S button.

S button

until the measure is

does not move, the display

does not move to position

to the right.

-40-

-41-

Page 22

EBA 430 E • EBA 430 EP

EBA

"Service"

None of the above mentioned methods helped to solve the problem:

Contact Service team under

• www.EBA.de service@krug-priester.com

Subject to alterations without notice.

➞➞

➞ "Service"

➞➞

Recommended accessories:

• Blade Nr. 9000 120

• Cutting stick (6 pieces) Nr. 9000 220

• Paper knock-up block Nr. 9000 520

• Blade changing tool Nr. 9000 515

• Cabinet Nr. 42618001

-42-

• Stand Nr. 43051100

-43-

Page 23

EBA 430 E • EBA 430 EP

Remarks:

MANUFACTURER’S DECLARATION

This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 98/37, 73/23 and 89/336.

EBA is certified under the DIN EN ISO 9001 quality standards.

The exact technical specifications can be found on the technical specifications sticker on the machine. A wiring diagram is found in the electric switch box.

Applied standards and technical specifications: 230 Volt-Version: EN 292; EN 294; EN 349; EN 27779; EN 55014-1; EN 55014-2; EN 60204; EN 61000-3-2;

EN 61000-3-3; prEN

1010-1; prEN 1010-3 Sound level information: The sound

level is 71 db (A) as defined by DIN 45635/Teil 27.

-44-

Wolfgang Priester

-General Manager-

-45-