Mazda Auto-Dimming Mirror User Manual
Cleaning the mirror:
When cleaning the m irror, use a paper towel or similar material dampened with
glass cleaner. Do not spray glass cleaner directly onto the mirror as damage to
internal circuitry may result.
FCC: NZLCTHL3. IC: 4112A-NZLCTHL3
Troubleshooting Guidelines:
1. “C” or “CAL” is displayed in the display window
a. Perform calibration procedure.
2. Inaccurate compass direction
a. Perform compass zone setting procedure and the n calibration procedure
b. Vehicle magnetics may hav e changed.
- Press and h old the “ ” button or the “ ” button (if mirror has) for 9
seconds until a “C” or “CAL” app ears in the display window.
- Perform c alibration procedure.
NOTE: Installing items such as a ski rack, antenna, luggage rack or recent body
repair can cause changes to the vehicle’s magnetic field. This may require
that the compass be recalibrated by performing the recalibration procedure.
3. The temperature display is reading significantly low
a. The temperature display may have been change d to degrees Cels ius. Refer
to the section of this User Guide perta ining to the temperature feature to
correct.
4. The display window shows “SC” or “OC” instead of temperature
a. These problems must be corrected at your authorized Dealer Service Center.
Fig. 5
9. Return to the veh icle and firmly press,
hold for 2 seconds and release the
programmed HomeLink
®
button. Fig. 5
10. Repeat Step 9 a second time and
possibly a third t ime (depending on
brand of device).
HomeLink
®
should now activate your
rolling code equipped device.
Gate Operator / Canadian Programming:
Canadian radio-frequenc y laws require trans mitter signals to “ti me-out” or quit after
several seconds of transmission – which may not be long enough for HomeLink
®
to pick
up the signal during programming. S imilar to this Canadian law, some U.S. g ate
operators are designed to “time-out” in the same manner.
If you live in Canada or you are having difficulties progra mming a gate operator by using
the “Programming” procedures (regardless of where you live), replace “Programming
HomeLink
®
step 4 with the following:
NOTE: If programming a garage door opener or gate operator, it is advised to unplug
the device during the “cycling” proces s to prevent possible overheating.
4. Continue to press and hold the HomeLink
®
button while you press and release
- every 2 sec onds (“cycle”) your hand-held transmitter u ntil the frequency signal
has successfully been accepted by HomeLink
®
. (The indicator light w ill flash
slowly and then rapidly.)
Proceed with “Programming” step 5 to complete.
NOTE: Programmed HomeLink
®
codes can be intentionally erased (when selling
vehicle etc.) by holding the 2 outer buttons (as shown in Fig. 1) for 20 seconds until LED
indicator begins to fl ash. Do not ho ld buttons for more than 30 seconds.
If you have any questions or are having difficulty programming your
HomeLink
®
buttons, please refer to www.homelink.com or call
1-800-355-3515.
Hold for 2 seconds and
release
To Operat e the Auto-Dim ming Feature:
Push the “ ” switch to turn the mirror on/off. The auto-dimming feature is
enabled when the green LED indicator is on.
To Operat e the Compass Feature:
1. Push the display “ ” switch. The vehicle’s directional heading will be displayed.
2. Pushing the “
” switch a second time will turn off the visua l display.
3. If the display reads “C”, calibrate the comp ass by driving the veh icle in up to 3
complete circles at less than 5 MPH.
CALIBRATION PROCEDURE
LED SENSOR
DIS PLAY
WINDOW
ON/OFF
BUTTON
Auto-Dimming Mirror User Guide
Auto-Dimming Mirror with Compass
Congratulations! Your n ew Mazda is equippe d with an Automatic-Dimming Mirror,
manufactured by Gentex Corporation. During nighttime driving, th is safety feature will
automatically detect an d eliminate dangerous rearview mirror g lare.
Your new mirror may or may not have all of the features shown in this User Guide.
Please refer only to the sections that pertain to the model mirror you have in your new
vehicle.
To Operat e the Auto-Dimming Feature:
Push the “ ” switch to turn the mirror on/off. The auto-dimming feature is
enabled when the green LED indicator is on.
To Operat e the Compass Feature:
1. Push the display “ ” switch. The vehicle’s directional heading will be displayed.
2. Pushing the “
” switch a second time will turn off the visua l display.
3. If the display reads “C”, calibrate the comp ass by driving the veh icle in up to 3
complete circles at less than 5 MPH.
4. To adjust for compass variance:
a. Press the “
” button for more than 9 seconds, or until the current zone
number appears in the display.
b. Find your current location and variance zone number on the z one map below.
c. Press the “
” button until the new z one number appears in the display.
After you stop pres sing the button, the d isplay will show a compas s heading
within a few secon ds.
CALIBRATION PROCEDURE
LED SENSOR
DIS PLAY
WINDOW
ON/OFF
BUTTON
550-0351 B
MazdaGuide550_0351A.hls 8/10/05 3:23 PM Page 1
To Operate the Auto-Dimming Feature:
Push the “ ” switch to turn the mirror on/off. The aut o-dimming feature is enabled
when the green LED indicator is on .
To Operate the Compass Feat ure:
1. Push the disp lay “ ” switch. The vehicle’s directional heading will be displayed.
2. Pushing the “ ” switch a second time will turn off the visual display.
3. If the display reads “C” or “CAL”, calibrate the compass by driving the vehicle in
up to 3 complete circles at less than 5 MPH.
Auto-Dimming Mirror with Compass and HomeLink
®
and
Auto-Dimming Mirror with Compass, HomeLink
®
and Temperature
HomeLink®and the HomeLink®house are registered trademarks of Johnson Controls, Inc.
4. To adjust for compass variance:
a. Press the “ ” button for more than 9 seconds, or unt il the current zone
number appears in the display.
b. Find your current location and variance zone number on the zone m ap below.
c. Press the “ ” button until the new zone number appears in the display. After
you stop pres sing the button, the display will show a com pass heading within
a few seconds.
To Operate the Temperature Feature:
1. Push the “ ” switch. The vehicle’s directional heading and outside temperature will
be displayed.
2. Pushing the “ ” switch a second time will turn off the visual display.
3. The temperature display can be changed to Celsius by depressing the “ ” switch for
3 seconds, until a “°C” appears by itself in the display window. Pushing the “ ” switch
again will toggle the display between Ce lsius and Fahrenhe it. Five seconds of no
switch activity returns the display to its normal direction al and temperature r eading.
SENSOR
LED
AUTO-DIMMING
ON/OFF BUTTON
DISPLAY WINDOW
(Larger w indow for
Temp. model)
HOM ELINK
BUTTONS
DIS PLAY
BUTTON
CALIBRATION PROCEDURE
Fig. 1
Fig. 2
To Operate the HomeLink®Feature:
Please refer to the programming instructions outlined in this User Guide or:
a. visit the HomeLink
®
website at www. homelink.com
b. call the HomeLink®customer sup port line at 1-800-35 5-3515
HomeLink®Programming Instructions:
WARNING!
Before programming HomeLink®to a garage door opener or gate
operator, make sure that people and objects are out of the way of the device to prevent
potential harm or da mage. When programming a garage d oor opener, it is advised to
park outside of the garage. Do not use HomeLink
®
with any garage door opener that
lacks safety stop and reverse features as required by U.S. federal safety stand ards (this
includes any garage d oor opener model manufactured before April 1, 1982). A garage
door that cannot det ect an object – signaling the door to stop and reverse – do es not
meet current U.S. federal safety standards. For more information, contact HomeLink
®
at
www.homelink.com
or by calling 1-800-355-3515.
1. To begin, press and hold the 2 outer
HomeLink
®
buttons (to clear memory) until
the indicator light (LED) blinks slowly
(approximately 20 seconds). Fig. 1
2. Release both buttons.
NOTE: Do not hold the buttons for longer than
30 seconds. Do not repeat this step when
programming addit ional devices to remaining
buttons.
3. Position the en d of the hand-held transmitter
1-3 inches away from the HomeLink
®
button
you wish to program while keeping the
the indicator light in view.
4. Simultaneously press and hold bot h the
chosen HomeLink
®
and hand-held transmitter
buttons. Fig. 2
Do not release the buttons until step 5 has
been completed.
NOTE: Some gate operator and garage door
openers may require you to replace this
Programming step 4 with procedures noted in the
“Gate Operator / Canadian Programming” section.
5. After the Hom eLink
®
indicator light changes
from a slow to a ra pidly blinking light, release
both the HomeLink
®
and hand-held transmitter
buttons.
6. Press and hold the just-trained HomeLink
®
button and observe the indicator light.
If the indicator light blinks rapidly for 2 seconds
and then turns to a constant light, the device being
programmed utilizes rolling code and
programming is not complete until the following
steps are completed. Fig. 3
7. On the garage door opener receiver
(motor-head unit) locate the “learn” or “smart”
button. This can usually be found where the
hanging antenna wire is attached to the
motor-head unit.
8. Firmly press and release the “learn” or
“smart” button. Fig. 4
NOTE: You have 30 seconds to initiate step 9.
Press an d Hold for 20 sec onds…
LED blinks slowly …
Release but tons
Press button…
Fast blink for 2
seconds then c onstant
= rollingcode…
Continue programmi ng
instructions
Fig. 4
Fig. 3
Press and holdboth…
LED blinks fa st…
Release bot h buttons
Press “Learn” button…
30 SECONDS TO GET TO VEHICLE
To Operat e the Auto-Dimming Feature:
Push th
e “ ” switch to turn the mirror on/off. The auto-dimm ing feature is enabled
when the green LED indicator is on.
To Operat e the Compass Feature:
1. Push the display “ ” switch. The vehicle ’s directional heading w ill be displayed.
2. Pushing the “ ” switch a second time will turn off the visual display.
3. If the display reads “C” or “CAL”, calibrat e the compass by driving the vehicle in
up to 3 complete circles at less than 5 MPH .
SENSOR
LED
AUTO-DIMMING
ON/OFF BUTTON
DIS PLAY WI NDOW
(Larger w indow for
Temp. model)
HOM ELINK
BUTTONS
DIS PLAY
BUTTON
CALIBRATION PROCEDURE
MazdaGuide550_0351A.hls 8/10/05 3:23 PM Page 3
Loading...