Maytronics Pulit E70 Instructions Manual

1

English

8151148

by

Pulit E70 Robot Pool Cleaner by Maytronics

EN

FR

IT

User Instructions

Guide d’utilisation

Istruzioni per l’uso

Instrucciones para el Usuario

Bedienungsanweisungen

SP

DEU

3

English

What You’ll Find Inside the Box

Part X Comment

Base frame for filter elements 2

Ultra-fine filter 4 filters

Bag for filters storage 1

Ultra-fine disposable filter with frames 1 set 10 disposable filters per set

Spring filter 4 filters

“S” clip 4

Power supply unit 1

Pulit E70 pool cleaner 1

Caddy kit 1

Optional components available on request from your Pulit E70 distributor

Section 1 - Description of Main Components

1. Filters

There are three types of filters.

Spring filter + base frame

For dirty pools with large debris such as
leaves etc. – Useful for beginning of season.

Ultra-fine filter cartridge + base frame

For day-to-day use.

Factory default.

Ultra-fine disposable filter + frame

For day-to-day use for up to 3 cycles.

2. Brushes

There are three types of optional brushes, each designed to provide optimal traction on different pool surfaces. Only one type set is
provided with your Pulit E70.

Standard Brush

For concrete, PVC, fiberglass and liner.

Combined Brush

For rough ceramic surface and mosaic tiles.

Wonder Brush

For smooth ceramics.

Power supply Unit

Pulit E70 pool cleaner

Filter and cartridges

4

English

3. Power supply unit

Digital, “Switch-Mode” power supply:

Input - 100-250 AC VoltsUÊ
50-60 HertzUÊ
180 WattUÊ
Output - 30 VDCUÊ
IP 54UÊ

Section 2 – Pulit E70 Operation

Part 1 – Preparing the Pulit E70 Pool Cleaner for Use

A. Assemble the Caddy kit – you will find the instructions in a separate document

B. Adjusting the handle float angle

The handle angel must be adjusted to determine the speed that the Pulit E70 advances along the water-line.

1. Lay the handle down at an angle of 180º to
the ground.

2. Push the base of the arm into the body of the
Pulit E70 and slide it towards the rear of the
Pulit E70 until it clicks into the required position.

Normal advance

More efficient cleaning action on water-line.

Fast advance

Fast speed – For faster but less efficient cleaning
action on water-line.

Push in here Slide here

Push in here

Slide here

ON

On/Off

switch

5

English

C. Laying out the cable

Unwind minimal required cable to cover the entire pool size, straight the cable along the pool side.
Make sure there are no twists or kinks.

Part 2 - Into the water

Inserting the Pulit E70 into the pool.

Place the Pulit E70 into the pool and release the handle.

Note: When using the Combined brushes or Wonder brushes, gently squeeze the Wonder brush material until it is totally wet.

Only use the original supplied power supply unit.

The Power supply unit is splash proof – do not immerse it in water.

Unplug the power supply unit before any servicing activity.

Do not plug the power supply unit in before placing the pool cleaner in the water.

Ensure the mains outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter (ELI).

3 Meters

10 feet

Swivel

6

English

Turning the Pulit E70 on

Part 3 - Taking the Pulit E70 out of the water

Unplug power supply before any servicing activity.

If the Pulit E70 has not finished its cycle, turn off the power supply 1.
unit and unplug the mains.

Pull the floating cable gently until the Pulit E70 has risen to the 2.
surface, then lift by the handle.

Plug the floating cable from the Pulit E70 1.
into the power supply unit.

Plug the electrical cable from the power 2.
supply unit into the mains.

Press the ON/OFF switch 3.

The Pulit E70 will now start to work.4.

Important: Do NOT lift the Dolphin from the water by its cable.

Floating cable

ON

On/Off

switch

Note : If your model includes the remote control unit, please refer to the included instruction leaflet.

7

English

Section 3 - Routine Maintenance

Part 1 - Extracting and cleaning the filter elements

Unplug power supply before any servicing activity.

Reassembling the filter elements

Insert the locating tabs at the bottom of the
filter element into their groves on the base frame,
then close the “S” clip.

Opening the Ultra-fine disposable filters

1. Open the filter frames by unclipping the

fasteners at the sides.

2. Rinse out the cartridge base, then reassemble

the cartridges with a new disposable filter.

Filter frame
Cartridge base

Side fastener

Locating tab

Locating tab groove

Disposable
Ultra-fine filter element

23

1

8

English

Reinstall the filters according to the diagram
DO NOT FORCE THE FILTERS INTO PLACE.

Part 2 - Dismantling and cleaning the impeller

Unplug power supply before any servicing activity.

Dismantle the impeller cover and
clean around the impeller housing,
then reassemble.

Grooved end fitting

Octagonal end fitting

Important: Where applicable, you must reset the full filter bag indicator on the power supply unit.

Important: When storing a Pulit E70 with Combined or Wonder brushes, please note to keep the brushes wet at all times.

Recommendation: Rinse all brushes with clean water after each cleaning cycle.

Coil the cable and store in dry cool area – preferably on the Caddy if available.

Do NOT store the Pulit E70 exposed to direct sunlight.

Do NOT store the Pulit E70 exposed to excessive heat.

Do NOT store the Pulit E70 exposed to frost.

Section 4 – Storage Advice

2

3

1

9

English

Troubleshooting Guide

Before contacting your Pulit E70 distributor please read through this guide.

The pool water condition must be within the following parameters:

PH: 7.0 – 7.4 Salt: Max 5,000 ppm
Temperature: 12˚C(54˚F) to 32˚C(90˚F) Chlorine: Max 2 ppm

Symptom Solution

Cable twisting or cable coils up Check for any obstruction in the pool

Change handle diagonal position after each use
Remove excess cable from the pool
Make sure filter cartridge is clean
Straighten cable and lay it in the sun periodically

Pulit E70 is moving in circles or does not reach all pool areas or
the Pulit E70 is not traveling sideways on walls

Check for foreign objects in moving parts
Make sure Filter elements are clean and that the filter doors

are closed
Make sure that there is enough cable laid out to cover the

whole pool
Before using the Pulit E70 at the beginning of the season you

should brush any algae from the floor and walls of the pool
Adjust the diagonal angle of the handle

Pulit E70 does not climb walls Make sure the filter cartridge is clean

If using the Pulit E70 at the beginning of the season, use the
spring cartridge

If using the Pulit E70 at the beginning of the season you should
first brush any algae from the floor and walls of the pool

Check if brushes are suitable for pool coating and replace them
if necessary

Check if brushes are worn and replace them if necessary
Make sure the impeller area is clean
When applicable: Check that the RCU is set for climbing

Pulit E70 not sinking Make sure the Wonder brushes or the combined brushes are

soaked in water
Pulit E70 disengaging from wall at water line If Pulit E70 climbs too high consult your Pulit E70 distributor
RCU is not working When applicable: Check if the batteries need replacing
Motor is not working Check if the impeller is blocked

Check if the drive system is blocked

Electrical problem (power supply), check power source.

If power source is in order, please contact your Pulit E70

distributor

Additional troubleshooting is available at our Website:

http://www.maytronics.com

10

French

Liste des pièces fournies dans l’emballage

Pièces X Remarques

Châssis des composants du filtre 2

Filtre ultrafin 4 filtres

Poche de rangement des sacs filtres 1

Filtre jetable ultrafin avec châssis 1 lot 10 filtres jetables par lot

Filtre pour nettoyage de printemps 4 filtres

crochet en “S” 4

Bloc d’alimentation 1

Robot nettoyeur de piscine Pulit E70 1

Kit Caddy 1

Les éléments optionnels sont disponibles sur demande de la part de votre

distributeur Pulit E70

Chapitre 1 - Description des principaux composants

1. Filtres

Trois types de filtres sont disponibles.

Filtre Printemps (pour nettoyage de
printemps) + châssis

Pour piscines sales contenant des saletés de
grande taille, par ex. des feuilles – utile en
début de saison.

Cartouche de filtre ultrafin + châssis

A usage quotidien.

Réglage d’usine, défini par défaut.

Filtre jetable ultrafin + châssis

A usage quotidien, conçu pour 3 cycles.

2. Brosses

Trois types de brosses sont proposés en option, chacune d’elles étant conçue pour fournir une traction optimale sur différentes sur­faces de piscine. Un seul ensemble brosse est fourni avec votre nettoyeur Pulit E70.

Brosse standard

pour surfaces en béton, PVC, fibre de verre
et à revêtement.

Brosse combinée

pour surface rugueuse en céramique et
pavés en mosaïque.

Brosse Wonder

pour sols en céramique lisse.

Bloc d’alimentation électrique

Robot nettoyeur de piscine

Pulit E70

Filtre et cartouches

11

French

3. Bloc d’alimentation électrique

Alimentation numérique avec
« Mode Interrupteur » (Switch mode):

Entrée - 100-250 AC VoltsUÊ
50-60 HertzUÊ
180 WattsUÊ
Sortie - 30 VDCUÊ
IP 54UÊ

Chapitre 2 – Fonctionnement du Pulit E70

1

ère

partie – Préparation du nettoyeur de piscine Pulit E70

A. Montez le kit du Caddy – mode d’assemblage indiqué séparément

B. Réglage de l’angle de la poignée du flotteur

Le réglage de l’angle de la poignée permet de déterminer la vitesse de progression du Pulit E70 le long de la
ligne de bordure de l’eau.

1. Abaissez la poignée à 180º au sol.

2. Poussez la base du bras à l’intérieur de l’appareil
Pulit E70 et faites-la glisser vers l’arrière du robot
jusqu’à entendre un clic d’enclenchement dans
la position voulue.

Progression normale

Pour un nettoyage plus efficace de la bordure de l’eau.

Progression rapide

Vitesse accélérée – pour un nettoyage plus rapide
mais moins appliqué de la bordure de l’eau.

Poussez ici Faites glisser ici

Poussez ici

Faites glisser ici

ON

Marche/ Arrêt

12

French

C. Disposition du câble

Déroulez le minimum nécessaire de câble pour assurer la couverture de toute la piscine. Veillez à le poser bien droit le long de la paroi
et vérifiez qu’il ne présente ni nœuds ni torsades.

2

ère

partie – Insertion du Pulit E70 dans l’eau

Installation du Pulit E70 dans la piscine.

Plongez votre Pulit E70 dans la piscine, puis lâchez la poignée.

Remarque: Lors de l’utilisation des brosses combinées ou de brosses Wonder, pressez doucement le matériau constitu-

ant la brosse pour l’humidifier à fond.

Utilisez exclusivement le bloc d’alimentation électrique d’origine.

Le bloc d’alimentation électrique est conçu anti-éclaboussures – Ne pas l’immerger dans l’eau.

Débranchez l’alimentation avant d’entreprendre toute activité d’entretien.

Ne branchez pas l’alimentation avant d’avoir placé le robot nettoyeur dans l’eau.

Assurez-vous que la prise du secteur est protégée par un interrupteur de mise à la terre (GFI) ou de fuite à la terre (ELI).

3 mètres

10 feet

Pivot (Swivel)