How it Works
Maytag
Loading...
W10557650B
User Manual
28 pgs4.85 Mb0

Maytag W10557650B User Manual

Use & Care Guide
ELECTRIC DRYER
W10557650B
If you have any problems or questions, visit us at www.maytag.com
ELECTRIC DRYER
TABLE OF CONTENTS
ASSISTANCE OR SERVICE ........................ Back Cover
DRYER SAFETY
IMPORTANT: When discarding or storing your old clothes dryer, remove the door.
2
3
OPERATING INSTRUCTIONS
CONTROL PANEL AND FEATURES
1
2
4
3
START
1
Press to start a cycle. Indicator light will glow to indicate the cycle has started.
2
TEMPERATURE
The Temperature Control button lets you choose between a normal and low drying temperature.
Normal
The Normal temperature setting is for sturdy fabrics, such as cotton, linen, and denim. If the Temperature Control button is not pressed in, the temperature setting is Normal.
Low
The Low setting is for synthetics, such as cotton/polyester blend, rayon, acetate, washable silk, or nylon. If the Temperature Control button is pressed in, the temperature setting is Low.
NOTE: Always refer to the care label on the garment to determine whether it can be tumble dried.
5
POWER
3
Press to turn the dryer on and off. Indicator light will ash to indicate the power is on.
4
CYCLE CONTROL KNOB
Use your dryer’s Cycle Control knob to select available cycles on your dryer. Turn the knob to select a cycle for your laundry load. See “Cycle Guide” for detailed descriptions of cycles.
POWER INDICATOR
5
This light ashes when the power is on and glows when a cycle is running.
END OF CYCLE SIGNAL
The dryer sounds a signal to let you know when the cycle is complete. The signal is not adjustable and cannot be turned off. The signal is helpful when you are drying permanent press, synthetics, and other items that should be removed promptly at the end of the cycle.
4
CYCLE GUIDE — SENSOR DRY CYCLES
Use Sensor Dry Cycles for better fabric care and energy savings
When you are using the GentleBreeze™ Drying System with IntelliDry® Sensor, two metal strips located in the dryer determine the dryness of the load. When there is moisture left in the clothes, the dryer will continue to run. As clothes begin to dry, the amount of water left in the clothes decreases, and the timer advances through the remainder of the cycle. When the selected dryness level is reached, the dryer goes into a cool-down period.
Sensor dry cycles may be used for most loads. Sensor dry cycles give the best drying results in the shortest time. Drying time varies according to the type of fabric, size of the load, and dryness setting.
After drying a load, check the dryness.
n
If the load is drier than you like, select a setting closer to Iron Dry the next time you dry a similar load.
n
If a load is not as dry as you like, complete drying using a Timed cycle. Select a setting closer to More Dry the next time you dry a similar load.
Items to dry: Cycle:
Temperature
Setting:
Cotton/Linen
Heavy cottons and denims More Dry Normal
Cottons and linens Normal Normal
Synthetics
White and colorfast permanent press Normal Low
White and colorfast items that require ironing Iron Dry Low
Polyester/acrylic blends, rayon, acetate Damp Dry Low
Washable silk and nylon Damp Dry Low
CYCLE GUIDE — TIMED DRY CYCLES
IMPORTANT: It is not recommended drying heavyweight items in Timed Dry cycle. Heavyweight items can be dried using Automatic cycles.
Use this cycle to get up to 60 minutes of heated drying time or to complete drying if items are still damp after the automatic cycle. Timed Dry is useful for lightweight items, such as lingerie, blouses, and knits that require a short drying time.
Items to dry: Time
(Minutes):
White and colorfast permanent press 40 Low
White and colorfast items that require ironing 40 Low
Polyester/acrylic blends, rayon, acetate 40 Low
Washable silk and nylon 40 Low
Temperature
Setting:
5
USING YOUR DRYER
WARNING: To reduce the risk of re, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
1. Clean the lint screen
3. Press POWER
Clean the lint screen before each load. Pull the lint screen straight up. Open lint screen. Roll lint off the screen with your ngers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove. Close lint screen. Push the lint screen rmly back into place.
For additional cleaning information, see “Dryer Care.”
2. Load the dryer
Press the POWER button to turn on the dryer. The indicator light will ash to indicate that the power is on.
4. Press TEMPERATURE
Press the TEMPERATURE button to select the recommended temperature setting for the type of load being dried.
Open the door by pulling on the handle. Place laundry in the dryer. Add a static reducing sheet to wet load, if desired. Close the door.
IMPORTANT: Do not tightly pack the dryer. Items need to tumble freely. Tightly packing the load can lead to poor drying performance and may increase wrinkling and tangling.
6
5. Select the desired cycle
Select the desired cycle for your load. See the “Cycle Guide” for more information about each cycle.
NOTE: Most loads may be dried using the Normal dryness level, which is shown in bold letters on the control panel. Normal is the energy preferred dryness level and will use the least energy.
6. Press START to begin cycle
Press and hold the START button to begin the cycle.
To stop your dryer at any time:
Turn the cycle control knob to the STOP position or open the door.
To restart the dryer:
1. Close the door.
2. Select a new cycle and temperature (if desired).
3. Press the START button.
DRYER CARE
CLEANING THE DRYER LOCATION
Keep dryer area clear and free from items that would block the air ow for proper dryer operation. This includes clearing piles of laundry in front of the dryer.
CLEANING THE DRYER INTERIOR
To clean dryer drum
1. Use a mild hand dish detergent mixed at a low
concentration with very warm water, and rub with a soft cloth.
2. Rinse well with a wet sponge or towel.
3. Tumble a load of clean clothes or towels to dry drum
OR Use a microber cloth and hot water in a spray bottle
to clean the drum and a second microber towel to dry.
NOTE: Garments that contain unstable dyes, such as denim blue jeans or brightly colored cotton items, may discolor the rear of the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside out to avoid transfer of dye.
To change the cycle or temperature after pressing START:
1. Open the dryer door.
2. Press the TEMPERATURE button to change the
temperature (if desired).
3. Turn the cycle knob to the new desired position.
4. Press the START button.
REMOVING ACCUMULATED LINT
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning should be done by a qualied appliance servicer or ventilation system cleaner.
From the Exhaust Vent
Lint should be removed every 2 years, or more often, depending on dryer usage.
7
CLEANING THE LINT SCREEN
Every load cleaning
The lint screen is located in the door opening of the dryer. The control panel has an indicator light to remind you to clean the lint screen before each load. A screen blocked by lint can increase drying time.
To clean:
1. Pull the lint screen straight up. Open lint screen. Roll lint
off the screen with your ngers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.
VACATION, STORAGE, AND MOVING CARE
Install and store your dryer where it will not freeze. Because some water may stay in the hoses, freezing can damage your dryer. If storing or moving your dryer during freezing weather, winterize it.
Non-Use or Storage Care
Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should:
1. Unplug dryer or disconnect power.
2. Clean lint screen. See “Cleaning the Lint Screen.”
Moving Care
For power supply cord-connected dryers:
1. Unplug the power supply cord.
2. Make sure leveling legs are secure in dryer base.
3. Use masking tape to secure dryer door.
2. Close lint screen. Push the lint screen rmly back into
place.
IMPORTANT:
n
Do not run the dryer with the lint screen loose, damaged, blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics.
n
If lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. See “Venting Requirements.”
As needed cleaning
Laundry detergent and fabric softener residue can build up on the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely dry. The screen is probably clogged if lint falls off while the screen is in the dryer.
Clean the lint screen with a nylon brush every 6 months, or more frequently, if it becomes clogged due to a residue buildup.
To wash:
1. Roll lint off the screen with your ngers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with
hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
For direct-wired dryers:
1. Disconnect power.
2. Disconnect wiring.
3. Make sure leveling legs are secure in dryer base.
4. Use tape to secure dryer door.
Reinstalling the Dryer
Follow the “Installation Instructions” to locate, level, and connect the dryer.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel.
Reinstall screen in dryer.
8
INSTALLATION INSTRUCTIONS
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Tools needed:
Flat-blade screwdriver Wood block
Wire stripper (direct wire installations)
Tin snips (new vent installations)
Parts needed: (Not supplied with dryer)
Vent clamps Vent elbows and ductwork Additional parts may be required, depending on your
installation. Check local codes. Check existing electrical supply and venting. Read “Electrical Requirements” and “Venting Requirements” before purchasing parts.
If using a power supply cord:
Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:
n A UL listed 30-amp power supply cord, rated 120/240 volt
minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.
n A UL listed strain relief.
Parts supplied:
Parts package is located in dryer drum. Check that all parts are included.
NOTE: Do not use leveling legs supplied if installing with a pedestal or a stack kit.
1/4" (7 mm) nut driver (recommended)
Level
®
Torx T20 screwdriver
†
Security
Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench
Caulking gun and compound (for installing new exhaust vent)
Coupling
Options: (Not supplied with dryer)
Pedestal
You may order a pedestal separately for this dryer. This pedestal will add about 12" (305 mm) to the height of your unit for a total height of approximately 45" (1.14 m).
To order, call the dealer from whom you purchased your dryer or refer to the “Assistance or Service” section of this manual. Ask for Model Number LAB0050PQ.
Stack kit
Are you planning to stack your washer and dryer? Your dryer is shipped with Stack Kit W10178021, which ts Maytag® washer models starting with MHWC.
If you have any other washer model, call the dealer from whom you purchased your dryer or refer to the “Assistance or Service” section of this manual.
†
® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.
9
Loading...
+ 19 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use