Maytag PYG4558AWW Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand [phone]

This Data Sheet Includes Information On

Maytag

• Product Model Number (s): •

Gas Dryers:

PYG4558AWW

14" max.

• Dimensions (Actual Size) •

Width:

27"

Height including control panel (0" leg adj):

Height NOT including control

panel (0" leg adj):

Depth with door open:

Minimum distance from working surface to

cabinets directly above:

Maximum depth of cabinet directly above:

Minimum clearance from back wall:

Minimum distance to door in front:

Minimum clearance right and left:

Door width:

• Additional Information •

• Electrical requirements: 20V, 60Hz, 15 ampere

grounded, fused electrical supply is required. An
individual branch (or separate circuit serving only this
appliance is recommended). Service cord NOT
provided.

• Minimum wire size of 10 gauge, copper wire only.

• Exhaust requirements:

- Dryer may be vented out rear, left side or through

floor (when venting left or down use Kit 33001881).

- Dryer must be exhausted to the outside.

- Use a minimum of 4" diameter rigid aluminum or rigid

galvanized steel duct.

- Keep exhaust as straight and short as possible.

Exhaust systems longer than the chart on page 2 will
extend drying time, affect machine performance and
collect lint.

- Termination hood should have at least 12" of

clearance between the bottom of the hood and the
ground or other obstructions.

- Back pressure must not exceed 0.92" of water column

when measured with a manometer.
See page 2 for additional information

Depth:

43 1/4"

35 3/4"
27 1/2"
49 3/4"

17"
14"
0"
2"
0"
22"

Side View

(not to scale)

Right

side

vent

Leg Adj.

0" wall clearance
on both sides

Back of unit

(looking out into room)

13 1/2"

0"

17"

36"

at 0"

9"

4 1/2"

3 1/2"

at 0"

Leg Adj

27 1/2"

22"

27"

Rear and Floor Venting

(not to scale)

4 3/4"

Back wall

Closet door

2" min.

Front View

(not to scale)

43 1/4"

at 0"

Leg Adj.

3 1/2" at 0"

Leg Adj.

Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of deter­mining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2002.

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.

337

Floor

2 3/8" at 0"

Leg Adj.

Gas Inlet Pipe

BN • A337B149 • • 020611 • 72428 • 25314

13 1/2"

www.dexpress.com

DIMENSION EXPRESS

Fax on Demand [phone]

Additional Information:

• Product installation in an alcove area or a closet requires sufficient

make-up air. Each make-up air opening must have a minimum of 36
square inches (more is better). These openings must not be
obstructed. A louvered door with equivalent air opening is acceptable.

• Gas requirements: Product comes equipped for use on NATURAL

GAS. If operated on LP gas, use kit 306195. Check with local
authorities for permission to convert if required (Canada).

- 1/2" gas supply line recommended, reduced to 3/8" for connection to

gas line on dryer.
1/8" N.P.T. plugged tapping recommended for access of test gauge
connection.

- Accessible line shut-off is recommended.

Page 2

This Data Sheet Includes Information On

Maytag

• Product Model Number (s): •

Gas Dryers:

PYG4558AWW

Maximum duct length chart

48 sq. in.

36 sq. in.

Minimum air openings
when installing behind
doors (two required).

36 sq. in.

24 sq. in.

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2002.

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.

3"

3"

Number

of 90°

turns

4"

4"

0 45 ft 30 ft
1 35 ft 20 ft
2 25 ft 10 ft

2 1/2"

Maximum length of
4" dia. rigid metal duct

BN • A337B149 • • 020611 • 72428 • 25314

149