Maytag ACS4140BB, ACS4140BW, DF454670, DF454677, MER4326AAA Installation Instructions

INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE

INSTALLATION MANUAL

Electric 30-inch Free-standing,

Slide -in & Drop-in Ranges

PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE

THE MANUAL IS INTENDED TO ASSIST IN THE INITIAL INSTALLATION AND ADJUSTMENTS OF THE RANGE.

SPECIAL WARNING

Only qualified personnel should
install or service this range.

Read “Safety Instructions” in the
Use & Care book before using
range.

Improper installation, adjustment,
alteration, service, maintenance or
use of range can result in serious
injury or property damage.

CLEARANCE DIMENSIONS

For complete information in regard to installation
of free-standing, drop-in and slide-in ranges,
see figures 1 through 4 on pages 2, 3 and 4. For
SAFETY CONSIDERATIONS do not install a
range in any combustible cabinetry which is not
in accord with the installation clearances shown
in figure 1.

CAUTION: Some cabinets and building
materials are not designed to withstand the
heat produced by the normal safe operation
of a listed appliance. Discoloration or
damage, such as delamination, may occur.

Your range may not be equipped with some of the features referred
to in this manual.

8101P371-60

(10-2000-00)

MOBILE HOMES

LOCATING THE RANGE

The installation of a range designed for mobile home
installation must conform with the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part
3280 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24 HUD, Part 280) or, when
such standard is not applicable, the Standard for
Manufactured Home Installations 1982 (Manufactured
Home Sites, Communities and Set-Ups), ANSI
A225.1-latest edition, or with local codes.

INSTALLATION DRAWINGS

IMPORTANT

PLEASE KEEP FOR THE USE OF THE
LOCAL ELECTRICAL INSPECTOR.

Place range in a well lit area. Do not set range over holes
in the floor or other locations where it may be subject to
strong drafts. Any opening in the wall behind the range
and in the floor under the range should be sealed. Make
sure the flow of combustion or ventilation air is not
obstructed.

“A” = 30 inches minimum clearance between the top of
the cooking surface and the bottom of an unprotected
wood or metal cabinet, or “A” = 24 inches minimum
when bottom of wood or metal cabinet is protected by
not less than 1/4-inch thick flame-retardant millboard
covered with not less than No. 28 MSG sheet steel,

0.015-inch thick stainless steel, 0.024-inch thick
aluminum, or 0.020-inch thick copper.

4

To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located

1

3

“A”

2

FIGURE 1

above the surface units should be avoided. If cabinet
storage is to be provided, the risk can be reduced by
installing a range hood that projects horizontally a
minimum of 5 inches beyond the bottom of the cabinets.

FIGURE 1

1, 2, 3 - COMBUSTIBLE BUILDING WALLS.

4 - COMBUSTIBLE WALL CABINET.

A free-standing range may be installed adjacent to (0²
from) combustible walls 1, 2 & 3.

A slide-in and drop-in range may be installed adjacent to
(0² from) combustible walls 2 & 3. The rear wall
clearance will be determined by cabinet cut-out depth
shown in illustrations on pages 3 and 4.

-2-

FREE-STANDING

FIGURE 2

SLIDE-IN

*23 1/4²

CUT DEPTH

BEFORE ATTEMPTING
INSTALLATION, ADJUST
RANGE LEVELING LEGS

51/2²
TO ACCOMMODATE
THIS DIMENSION.

10²

36² COUNTER

TOP HEIGHT

30² CABINET

OPENING

CAUTION:

SOME WHITE EUROPEAN STYLE CABINETS ARE EQUIPPED WITH DELICATE WHITE VINYL
DRAWER AND DOOR FRONTS. THE VINYL MAY NOT BE DESIGNED TO WITHSTAND THE
HEAT PRODUCED BY THE NORMAL SAFE OPERATION OF A SELF-CLEAN RANGE.
DISCOLORATION OR DELAMINATION MAY OCCUR. TO AVOID POSSIBLE DAMAGE, WE
RECOMMEND INCREASING THE 30² CABINET OPENING TO 31 1/4² MINIMUM AND USING
HEAT SHIELD KIT-CABKIT V. THE COUNTERTOP CUT-OUT MUST REMAIN 30².

30²

51/2²

23 5/8² MIN.

FLAT

AREA

24² CABINET

DEPTH

NOTE:

ON CABINET TOPS WITH
FORMED FRONT EDGE, SHAVE
RAISED SECTION TO CLEAR TOP.

PROVIDE FOR 120/208,
120/240 VOLT OUTLET
PER APPLICABLE
CORD IN THIS AREA.

25² MINIMUM

COUNTER

TOP DEPTH

FIGURE 3

* When replacing an existing unit, a maximum of 23 1/2² is acceptable. If the cut depth exceeds 23 1/2², use filler kit (K70 Fill).

-3-