D,shwash
Troubleshooting :ii.iiii:9'lO
Warranty & Service ........ 11
Guide d'utilisation
et d'entretien .............. 12
Gui_ de Uso y Cuidado ..... 24
Part No. 6 920185 A _2005 Maytag Appliances Sales Co.
What You Need to Know About
Safety Instructions
Warning and Important Safety Instructions appearing in this
manual are not meant to cover all possible conditions and
situations that may occur. Common sense, caution and care
must be exercised when installing, maintaining or operating
tile dishwasher.
Always contact your manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words, Labels
Important Safety Instructions
Products with a vL_)label have been listed with
Underwriter's Laboratories, Inc. - those with a CSA tag have
been listed with Canadian Standards Association.
Nevertheless, as with any other equipment using electricity
and moving parts, there is a potential hazard.
1. Read all instructions before using the dishwasher.
2. Use the dishwasher only for its intended function.
3. Disconnect electrical power to dishwasher before
attempting to service.
4. To avoid electrical shock hazard, the sides and back
must be enclosed and the front panels must be
attached before electrical power is applied to the
dishwasher. Refer to the installation instructions for
proper grounding procedures.
5. Connect to a properly rated, protected and sized
power supply circuit to avoid electrical overload.
6. Children should never be permitted to operate, or play
in, with, or around this dishwasher.
Z Toreduce the risk of injury when loading items to be
washed, sharp or pointed items should be locatedwith
the handles up. Also, load sharp items so they are not
likely to damage the door seal.
8. Do not touch the heating element on the bottom of
the tub during or at the completion of a cycle. It will
be [lot.
9. Use only detergents and rinse additives designed for a
residential automatic dishwasher. Never use soap,
laundry detergent, or hand washing detergent in your
dishwasher. Keep these products out of reach of
children.
10. Do not sit, stand on or abuse the door or dish racks of
the dishwasher.
11. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more.Hydrogen gas is
explosive. If the [lot water system has not been used
for such a period, turn on all hot water faucets and let
the water flow from each for several minutes. This will
release any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this process.
12. Do not wash plastic items unless marked "dishwasher
safe" or the equivalent. For plastic items not so
marked, check the manufacturer's recommendations.
13. Do not tamper with controls.
14. To prevent accidental child entrapment and
suffocation risks, always remove the door to the
washing compartment when removing an old
dishwasher from service or discarding it.
15. Use caution when unloading the dishwasher. Dishes
will be [lot if unloaded shortly after a cycle has
completed.
16. Certified residential dishwashers are not intended for
licensed food establishments.
1Z To avoid water, mold or mildew damage to your home,
inlet and drain hose connections should be checked
periodically for leaks.
Save These Instructions
for Future Reference
WhatCanandCannotBeWashed
Most tableware, cookware and flatware can safely be washed in your dishwasher. Check with the manufacturer.
Aluminum Yes, except anodized. High water temperature and detergents may affect finish.
Cast Iron No Seasoning will be removed, and iron will rust.
China/Stoneware hand-painted. Antique, hand-painted or over-the-glaze patterns may fade. Gold leaf
Crystal Yes, except antique or Always check manufacturer's recommendation before washing. Some
Filters Not recommended. May leave a dingy deposit or stain on dishwasher interior.
Glass Yes A specialty glass called milk glass can yellow with repeated dishwasher
Gold-Plated Flatware No Will discolor.
Pewter, Tin No
Plastics disposable plastic vary intheir capacity to withstand high water temperatures and
Stainless Steel Yes Run a Rinse Only cycle (select models) if not washing immediately.
Sterling Silver or No, if has commercial Always check manufacturer's recommendation before washing. Run a
Silverplate "darkening". Rinse Only cycle (select models) if not washing immediately. Prolonged
Wooden Items No Wood may warp, crack or discolor.
Yes, except antique or Always check manufacturer's recommendation before washing.
may discolor.
delicate crystal, types of leaded crystal may etch with repeated washings.
washing.
Yes, top rack, except Always check manufacturer's recommendationbefore washing. Plastics
items, detergents. Disposable plastic itemsare not dishwasher safe for this
reason.
Prolonged contact with foods containing salt, vinegar, milk products or
juice could damage finish.
contact with food containing salt, acid or sulfide (eggs, mayonnaise
and seafood) could damage finish. Commercial "darkening" may be
removed by detergent.
2
OperatingTips
Before You Start
• Don't prerinse. Simply scrape off any bones or
large food particles.
• If connected to a food waste disposer, make certain
the disposer is empty before starting the
dishwasher.
• Scrape off tomato-based food soils (see page 8).
• Remove certain foods such as mustard,
mayonnaise, lemon juice, vinegar, salt or dressings
from stainless steel flatware as soon as possible.
These foods may cause rusting and pitting if allowed
to remain in contact with the surface for an extended
period of time.
Starting the Dishwasher
1. After loading the dishwasher and adding detergent,
select the desired cycle by pressing the cycle
select pad until the light next to the desired cycle
is illuminated. Choose the desired options by
pressing the pads. The indicator lights for the
selected cycle and options will illuminate. To cancel
an option press the pad again.
2. To start a cycle, close the door until it latches then
press the START/Cancel pad once. After a pause,
the fill will begin. The display countdown (select
models) will flash until START/Cancel is pressed.
,
To cancel a running cycle, press the START/Cancel
pad once. The dishwasher will drain, then shut off.
To turn the dishwasher off without draining, press
the START/Cancel pad twice. To prevent
unplanned cycle or option changes, these selections
are "locked in" after 1 minute.
Note
• If the cycle select pad is pressed after the
controls have been "locked in", the light beside
the selected cycle will flash three times.
Adding a Forgotten Item
For best cleaning, the forgotten item should be added
early in the cycle.
1. Grasp door handle and unlatch door without
opening completely. All lights will flash to indicate
that the cycle is suspended.
2. Wait for the water circulation to stop.
3. Open the door and add the item.
4. Close and latch the door. Lights will stop flashing
when the door is properly shut. After a slight delay,
the cycle resumes automatically at the point of
interruption.
Notes
Note
• If STARTICancel is not pressed within 30
seconds of choosing your cycle, the dishwasher
will turn off.
The dishwasher remembers your last cycle so you
do not have to reset the cycle each time. To start
the dishwasher using the same cycle and options
selected on the previous wash, just press the
START/Cancel pad.
• If the door is opened during a running cycle,
there may be up to a 30 second delay before the
dishwasher restarts after closing the door.
• Extended interruption of the wash cycle is not
recommended.
3
Loading
General Recommendations
[Rack features vary by model)
• Items can be centered behind a single tine or loaded
at an angle to maximize space.
• Avoid blocking or preventing the spray arms from
spinning freely. Do not allow items to extend beyond
the racks.
• Face soiled surfaces toward the center of the
dishwasher.
For best dishwashing results follow these guidelines to
determine the best arrangement for your items.
10 Place Setting Load
[Rack features vary by model)
To remove the basket(s) from the door:
1. Grasp the utensil basket by
the handle. Slide it toward
the top of the door.
2. Lift the basket off the
securing knobs.
To replace the basket(s) in
the door:
1. Align the slots on the
backside of the utensil
basket with securing knobs
on the door.
2. Set the utensil basket on the securing knobs.
3. Slide the basket toward the bottom of the door until
it locks into place.
Removing the Upper Rack
The rack can be removed when tall or oversized items
need to be loaded into the lower rack. Unload the
rack before removing it from the dishwasher.
To remove rack with tab-lock rack stops:
Upper Rack
Lower Rack
Upper Rack
Glasses, cups, stemware, light-weight plastics, plates,
bowls, pans, long-handled utensils etc. can be loaded
in this rack. Do not load glasses over the tines.
Lower Rack
A variety of items such as dinner plates, mixing bowls,
pots and pans and baking dishes can be loaded in this
rack.
Wider items can be placed along the left side and
back of this rack.
Utensil Baskets
Removable Door Utensil Baskets
For best cleaning results, prevent
items from nesting together by
placing some items in the baskets
with handles up and some with
handles down. Load knives
handles up and spoons and forks
handles down.
.
Roll the rack '/3to '/_of the way out.
2.
Locate the rack stops at the end of each track.
Squeeze the tab in the middle of the rack stop and
pull the rack stop straight out. Take care to support
the rack while removing the rack stops.
3. Roll the rack all the
way out of the track
and remove from the
dishwasher.
To replace:
1. Replace the
dishwasher rack by Stylemay
guiding the wheels varybymodel
into the tracks.
2. Push each rack stop squarely into the end of the
track until the catch pops into the small hole on the
side of the track.
Important: ........
operate correctly if the _ _
The dishwasher will not _i _ _ _N
wash arm is not aligned _ _
with one of the water inlet _ _
holes on back wall of the _ _ _
dishwasher. _ _ _ _,
Rack
Stop
DishwasherUse
Hot Water
For optimal cleaning and drying results, hot water
is necessary. The incoming water temperature
should be 120 ° F [49 ° C) to properly activate the
detergent and melt greasy food soils.
To check the incoming water temperature, turn on the
hot water faucet nearest the dishwasher and let it run
into a glass in the sink. Place a candy thermometer in
the glass and check the temperature once it has
stopped rising.
Detergent
Use a detergent designed specifically for use in an
automatic dishwasher. Be sure it is fresh. Store
granular detergent in a cool, dry place (not under the
sink).
Recommended Amount
Too little detergent results in poor cleaning, hard water
filming/spotting and poor drying. Too much detergent
can cause permanent etching/cloudiness.
Suds can cause the dishwasher to overflow. Measure
the detergent carefully and use only detergents
designed for use in a dishwasher. Less detergent is
needed in soft water. Try another brand of detergent if
sudsing continues.
The amount of detergent to use is determined by the
hardness of the water and soil level of the load. Refer
to the following chart for detergent usage
recommendations.
Light Soil 2 tsp 6 tsp
Soft (0-4 gpg) Normal Soil /4tsp 6 tsp
Heavy Soil /4tsp 7 tsp
Light Soil /4tsp 6 tsp
Medium (5-9 gpg) Normal Soil /4tsp 6 tsp
Heavy Soil 5 tsp 7 tsp
Hard (10-12 gpg) All Levels 5 tsp 8 tsp
*Your local water utility or state university extension service can tell
you the degree of water hardness in your area.
In extremely hard water conditions (13 grains per
gallon or more*), it is difficult to achieve good
results with any dishwasher. A mechanical water
softener may be necessary to improve water
quality, detergent effectiveness, and protect the
dishwasher parts from the damage that hard
water can cause.
Add recommended amount of detergent to each cup
as shown and close the detergent lid.
Do not use detergent with the Rinse Only (select
models) cycle. Leave the detergent lid open when
running Rinse Only (select models).
Rinse Aid
Regular use of a rinse aid improves drying,
reduces spotting and filming, and reduces
moisture left on the dishwasher interior.
An automatic rinse aid dispenser is located next to the
detergent cup.
The window next to the dispenser cap indicates when
the rinse aid reservoir needs to be refilled. When the
level of rinse aid is below the indicator marks and the
window is nearly clear, it is time to refill the dispenser.
Check the dispenser monthly.
To add rinse aid to the
dispenser, turn the cap
counterclockwise to open.
Remove the cap and pour
liquid rinse aid into the
opening. The amount of
rinse aid dispensed during
the cycle is adjustable by moving the lever inside the
reservoir area. For most water conditions use the
manufacturer recommended setting of "2". Adjust it up to
the "MAX" setting for hard water. Set the lever anywhere
between these amounts as needed to get the best results.
Replace the cap and turn it clockwise to close.
5
Cycles,OptionsnndLights
Cycles
Choose the cycle that best describes your dishload by pressing the cycle select pad. (See page 3, Operating
Tips, for how to begin the cycle).
Heavy Wash Long cycle for heavy food soils. 132" 2 washes/3 rinses
Medium cycle for average food soils.
Normal Wash The turbidity sensor is active with this 97-117" 1-2 washes**/1-2 rinses**
cycle.
Light/Quick Wash Short cycle for light food soils. 82* 1wash/2 rinses
Rinse Only Rinses dishes being held until there 9 1rinse
(select models) is a full load.
Includes approximately 30 minutes of dry time.
**Number of fills will vary depending on the soil level of each load.
Note [
• Depending on water temperature, there may be time added to the cycle to bring water up to temperature.
Options
In addition to choosing a cycle, choose as many available options as are needed for your dishload.
Hi Temp Wash provides additional heat during the wash portion of the cycle, All cycles
Hi Temp Wash which ensures proper water temperature for better cleaning and drying results. (except Rinse Only
Heated Dry surfaces may be necessary and more moisture may be noticed adhering (except Rinse Only
Delay Used to automatically start the cycle at a later time. See page 7 All cycles
It also adds an additional rinse to the cycle which improves results in hard [select models])
water situations.
For enhanced drying results select this option. When Heated Dry is not
selected, towel drying of some items such as plastic and items with non-stick All cycles
to the dishwasher interior. In models with plastic interiors, it is normal to [select models])
notice vapor escaping from the door vent as the heat dries your dishes. Vapor
will escape even if Heated Dry is not selected.
for instructions.
6
Cycles,OptionsnndLights
Delay
The Delay option can be used to automatically start
the cycle at a later time to reduce daytime heat
buildup in the home or to take advantage of reduced
energy costs if available in your area. This option is
also useful for conserving hot water at times of high
household usage (showers, laundry).
To set up a Delay:
1. Select the appropriate cycle and options for the
load. Close the door.
2. Press the Delay pad until the desired amount of
delay time is selected.
3. The Delay indicator and the count down display
(select models) will flash until the START/Cancel
pad is pressed.
/4. As soon as the START/Cancel pad is pressed, the
flashing will stop and the delay time will begin
counting down. The Delay indicator will remain lit
until the delay time has counted down.
5. The cycle will automatically start as soon as the
delay time expires.
Note
• If 30 seconds elapse between setting the cycle
and options and pressing the START/Cancel
pad, the dishwasher will turn off.
To cancel a Delay:
When the delay is counting down, press the Delay pad
again. The indicator light will go out and the cycle will
start or resume immediately.
To cancel a Delay and the cycle:
• Press START/Cancel once to drain and turn off the
dishwasher.
Or
• Press START/Cancel twice to turn dishwasher off
without draining.
Lights
7
CareandCleaning
General Recommendations
• The dishwasher interior is normally self-cleaning.
Periodically check the bottom of the dishwasher tub
to see if any large particles remain.
• Wipe the edge of the inner door liner to remove any
food soil splashes which occurred during loading.
• When cleaning stainless steel, always wipe with the
grain. Never use products containing chlorine bleach
or citric acid.
Standard Exterior
Stainless Steel
Exterior
(select models)
Interior Light to moderate
*Brand names are trademarks of the respective manufacturer.
**Call 1-877-232-6771 to order.
Light to nloderate
Daily cleaning and light soil
Moderate to heavy soil
Streaks or fingerprints/restore shine
Discoloration
Discoloration, or tomato-based stain
• The color from some tomato-based food soils may
occasionally adhere to various components of the
dishwasher interior, causing temporary discoloration.
To minimize this:
• Remove excess tomato-based food soils from dishes,
before loading.
• Run the Heavy Wash cycle when washing loads
containing tomato-based food soils.
• Use a dishwasher detergent that contains chlorine to
better fight staining.
Soft damp cloth and liquid spray cleaner.
Do Not use abrasive powders or cleaning pads.
Soft cloth or sponge and one of the following:
• Mild detergent and water
• A solution of white vinegar and water
• Formula 409 Glass and Surface Cleaner*, or
similar multi-surface cleaner.
• Do Not use products containing chlorine
bleach or citric acid.
Follow with rinse and dry.
Soft cloth or damp sponge and Bon Ami*.
Follow with rinse and dry.
Soft cloth and Stainless Steel Magic Spray**.
Soft cloth or damp sponge and Cameo Stainless
Steel Cleaner*. Rinse immediately and dry.
Soft cloth or damp sponge.
Switch dishwasher detergent to chlorine-based
product.
Storage/Moving
Fill detergent cup with a fresh-scented dishwasher
detergent or baking soda and select the Normal Wash
cycle. Allow the dishwasher to complete the cycle. Then
turn the water supply off and drain the dishwasher. To
drain, press the START/Cancel pad once to activate
the dishwasher. Press START/Cancel again to activate
the drain. Operate the drain twice to ensure most of
the water is removed. Last, disconnect the electrical
supply and prop open the door.
When turning the water supply to the home off, the
water shut off at the dishwasher must be turned off also.
8
Troubleshooting
CHECK THESE POINTS TO HELP SAVE YOU TIME AND MONEY.
BL : ....
Dishwasher will not fill • Pressthe START/Cancel pad to start tile dishwasher.
• Besure door is latched securely.
• Besure the water is turned on.
• Check that the pad is properly selected for a cycle.
• Check your home's circuit breaker or fuse box.
• Check inlet [lose for a kink.
• Check water valve inlet for sediment and clean if necessary.
Dishwasher will not drain/
water in tub bottom
Dishwasher adds water at • This is normal. The sensor (select models) in the pump must stay submerged so a
end of cycle short fill of water is added after the cycle's last drain.
Detergent cup is not empty • Check that the cycle is completed.
Dishwasher seems noisy "
• If hooked up to a food waste disposer, be sure the knock-out is removed from the
disposer inlet.
• Check for food obstruction in the drain or disposer.
• Check drain hose for a kink.
• Check your home's circuit breaker or fuse box.
• Check that the cycle is completed.
• Besure dispenser is not blocked.
• Usefresh detergent stored in a cool, dry place.
A water valve hiss during fill is normal.
Water circulation sounds are normal.
A thumping sound may be a wash arm bumping an item that is extending beyond the
racks. Readjust load to avoid obstructing wash arm.
Chopping or grinding sounds may be heard as the internal chopper blade chops [lard
items like fruit seeds, nuts, etc.
Humming during the drain is normal.
A snap noise is the detergent cup lid hitting the door liner when the dishwasher door
is opened at the end of the cycle. This is normal.
Proper installation affects the noise level.
Cycle takes too long • Hi Temp Wash has been selected and the cycle is extended to heat water.
• Check to see that the incoming water temperature is 120° F (49° C).
Dishwasher has an odor •
Dishwasher leaks
*Brandnamesaretrademarksof the res
Run dishes being held in the dishwasher through a Rinse Only cycle (select models).
Marly dishwashers [lave a "new" smell when first installed. This will dissipate with use.
Dishwasher may not be draining properly. (See"Dishwasher Will Not Drain" section.)
Fora strong odor, place baking soda in both sides of the detergent cup. Select
Light/Quick Wash cycle and allow the water to circulate for about 10 minutes.
Interrupt the cycle by unlatching the door and let it stand overnight. Restart the
dishwasher by latching the door and allow it to complete the cycle. Another alternative
is to use a dishwasher cleaning product such as Jet-Dry Dishwasher Cleaner*.
• Check that the dishwasher is level. (Refer to the Installation Instructions.)
• Suds can cause the dishwasher to overflow. Measure the detergent carefully and use
only detergents designed for use in a dishwasher. Lessdetergent is needed in soft
water. Try another brand of detergent if sudsing continues.
Follow directions closely on how to add a forgotten item (jog.3).
Toavoid rinse aid leaking from the dispenser, besure the lid is securely attached.
_ectivemanufacturer. Cont.
9
Troubleshooting
Indicator lights flashing • The countdown display (:select models] flashes after a cycle is selected until the
START/Cancel pad is pressed.
• The countdown display (:select models] and the delay indicator flash after a delay is selected
until the START/Cancel pad is pressed.
• All active display indicators flash if the door is opened during a running cycle or delay.
• The currently selected cycle flashes if an attempt is made to change the cycle after cycle
"lock-in".
Glasses are cloudy/ • Select Hi Temp Wash option.
spotted • Check water temperature. Incoming water should be 120° F (49° C].
• Always use a rinse aid.
• Confirm that the cloudiness is removable by soaking the item in white vinegar for
approximately 5 minutes. If removed, the problem is due to [lard water. Adjust detergent
amount being used to match water hardness _pg. 5]. Be sure detergent is fresh, stored
properly and is a high quality brand.
• If cloudiness is not removable, it is etching. This is an erosion of the surface of the
glassware and carl be caused by water that is too hot, from using too much detergent or by
prewashing. Detergent needs food soil to act upon. If etching has occurred, the glassware
is permanently damaged. To prevent further etching, adjust the detergent amount to match
the water hardness, stop prewashing, and use water heating options only when incoming
water temperature is below 120° F (49 ° C].
Food soil remains • Check water temperature. Incoming water should be 120° F (49° C].
on dishes • Run hot water at the sink before starting the dishwasher.
• Check water hardness and adjust detergent amount accordingly _pg. 5].
• Use fresh detergent stored in a cool dry place.
• Select proper cycle for the soil level and Hi Temp Wash (select models] (pg. 6].
• Make sure the upper rack wash arm connector is correctly aligned in one of the water inlet
holes (pg. 4].
• Load items so they do not block the wash arms (pg. 4].
• Load the utensil basket with knife handles up and spoon and fork handles down.
• Do not place glasses over tines.
• Before loading, scrape off burnt on foods and wipe the starchy film from utensils used with
pasta, rice and oatmeal. These soils require more energy than the rest of the load to clean.
Items washed in the • Aluminum utensils or pans can leave marks when they rub against other items. Leave a
dishwasher or the slight space between items.
dishwasher tub itself • Iron deposits in the water can leave a yellow, brown or orange film on dishes or the
are stained/discolored dishwasher tub. A rust filter may be needed. Check with a water treatment company.
• Separate silver or silver-plated silverware from stainless steel. These metals can be
damaged by contact with each other during washing.
• Color from tomato sauces may adhere to the interior parts of the dishwasher (log. 8]. If light
staining has occurred, leave the door open to oxidize the stain away. Use a dishwasher
detergent that contains chlorine to better fight staining.
• Certain dishwasher detergents may stain silver. Try another brand of detergent.
Items not properly • Be sure Heated Dry is selected.
dried/moisture is • Water droplets may form on the inner door as part of the drying process.
present on the • Use a rinse aid separate from the detergent like Jet Dry* or Cascade Rinse Aid* regularly, to
dishwasher interior improve drying. Turn the rinse aid selector toward the MAX setting.
after the dry cycle • Check water temperature. Incoming water should be 120° F (49° C].
Dishware is chipped • Load dishes according to instructions so they do not strike each other _pg. 4].
• Select Hi Temp Wash option.
• Increase detergent amount to match water hardness (pg. 5].
• Load properly. _pg. 4]
• Plastic and items with non-stick surfaces are difficult to dry because they have a porous
surface which tends to collect water droplets. Towel drying may be necessary.
• Glasses and cups with concave bottoms hold water and require towel drying. Locate these
items on the more slanted side of the rack for improved results.
• Washing fine antique china/crystal in the dishwasher is not recommended.
• Do not load glasses over the tines.
• Do not overload.
*Brand names are trademarks of the respective manufacturer. 10