Maytag MYR20, MYR25, MYR30, MYR40, MYR55 Installation Instructions
...
INSTALLATION INSTRUCTIONS
COMMERCIAL WASHER-EXTRACTOR
INSTRUCTIONS D’INSTALLATION
LAVEUSE À EXTRACTION COMMERCIALE
MYR20, MYR25, MYR30, MYR40, MYR55, MYR65
Table of Contents/ Table des matières.................................................2
www.maytagcommerciallaundry.com
WFR124390B
2
TABLE OF CONTENTS
WASHER SAFETY .......................................................................2
SPECIFICATIONS .......................................................................4
INSTALLATION REQUIREMENTS .............................................. 8
LOCATION REQUIREMENTS .....................................................9
FLOOR REQUIREMENTS .........................................................16
INSTALLATION OF THE RIGID WASHER-EXTRACTOR
WITHOUT PEDESTAL BASE ....................................................17
INSTALLATION INSTRUCTION ................................................ 19
ELECTRICAL CONNECTION ...................................................21
WASHER MAINTENANCE ........................................................25
TABLE DES MATIÈRES
WASHER SAFETY
3
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
washer, follow basic precautions, including the following:
Do not allow children to play on, in, or with
the washer. Close supervision of children
is necessary when the washer is used near
children.
Before the washer is removed from service
or discarded, remove the door or lid.
Do not reach into the washer if the drum,
tub, or agitator is moving.
Do not install or store the washer where it
will be exposed to the weather.
Do not tamper with controls.
Do not repair or replace any part of the
washer or attempt any maintenance unless
that you understand and have the skills
to carry out.
See “Electrical Requirements” for
grounding instructions.
This appliance must have power locked
out using proper lockout and tag out
procedure during service and when
replacing parts. Refer to the OSHA
standard for “The Control of Hazardous
Energy (Lockout/Tag out)”, Title 29 Code
of Federal Regulations (CFR) Part
1910.147.
Read all instructions before using the
washer.
Do not wash articles that have been
previously cleaned in, washed in, soaked
in, or spotted with gasoline, dry-cleaning
substances as they give off vapors that
could ignite or explode.
Do not add gasoline, dry-cleaning
substances to the wash water. These
substances give off vapors that could
ignite or explode.
Under certain conditions, hydrogen gas
may be produced in a hot water system
that has not been used for 2 weeks or
more. HYDROGEN GAS IS EXPLOSIVE.
If the hot water system has not been
used for such a period, before using the
washer, turn on all hot water faucets and
minutes. This will release any accumulated
this time.
4
DIMENSIONS AND TECHNICAL SPECIFICATIONS
Model
Cylinder Volume
Liters (cu. ft.)
Cylinder diameter
mm (in.)
Cylinder depth
mm (in.)
Dry load
capacity kg (lb)
Max. spin
RPM
Max. extract
force (G-force)
MYR20 78 (2.74) 530 (20.9) 352 (13.9) 9 (20) 838 200
MYR25 108 (3.76) 620 (24.4) 352 (13.9) 11 (25) 790 200
MYR30 138 (4.86) 620 (24.4) 454 (17.9) 14 (30) 790 200
MYR40 183 (6.45) 750 (29.5) 411 (16.2) 18 (40) 693 200
MYR55 242 (8.56) 750 (29.5) 548 (21.6) 25 (55) 693 200
MYR65 276 (9.76) 750 (29.5) 621 (24.4) 30 (65) 693 200
Dimensions
Washer Dimensions
B
C
D
A
A B C D
Model
Width
mm (in.)
Door
Opening
mm (in.)
Depth
mm (in.)
Height
mm (in.)
MYR20 660 (26) 328 (12.9) 686 (27) 1112 (43.8)
MYR25 750 (29.5) 410 (16.1) 725 (28.5) 1222 (48.1)
MYR30 750 (29.5) 410 (16.1) 840 (33.1) 1222 (48.1)
MYR40 890 (35.0) 459 (18.1) 876 (34.5) 1410 (55.5)
MYR55 890 (35.0) 459 (18.1) 1011 (39.8) 1410 (55.5)
MYR65 890 (35.0) 459 (18.1) 1085 (42.7) 1410 (55.5)
Additional Clearances:
■ Additional spacing of 25 mm (1") on both sides of the washer
is recommended to reduce noise transfer.
■ Additional spacing of 500 mm (20") between the rear of the
washer and the wall is recommended for ease of servicing.
5
DIMENSIONS AND TECHNICAL SPECIFICATIONS
Dimensions
Washer Rear Dimensions
A. Electrical Connection F. Steam Connection (Option)
B. Hot Water G. Liquid Soap Connection
C. Cold Water H. Disconnect
D. 2nd Cold Water (Option) I. USB Port
E. Drain J. Fuses
MYR20 MYR25 MYR30 MYR40 MYR55 MYR65
A1
mm
(in.)
451
(17.7)
543
(21.4)
543
(21.4)
578
(22.7)
578
(22.7)
578
(22.7)
A2
mm
(in.)
1045
(41.1)
1156
(45.5)
1156
(45.5)
1343
(52.8)
1343
(52.8)
1343
(52.8)
B1
mm
(in.)
225
(8.8)
225
(8.8)
225
(8.8)
289
(11.4)
289
(11.4)
289
(11.4)
B2
mm
(in.)
1000
(39.4)
1108
(43.6)
1108
(43.6)
1224
(48.2)
1224
(48.2)
1224
(48.2)
C1
mm
(in.)
101
(4.0)
101
(4.0)
101
(4.0)
175
(6.8)
175
(6.8)
175
(6.8)
MYR20 MYR25 MYR30 MYR40 MYR55 MYR65
C2
mm
(in.)
1023
(40.3)
1133
(44.6)
1133
(44.6)
1321
(52)
1321
(52)
1321
(52)
D1
mm
(in.)
146
(5.7)
146
(5.7)
146
(5.7)
175
(6.8)
175
(6.8)
175
(6.8)
D2
mm
(in.)
927
(36.5)
1035
(40.8)
1035
(40.8)
1224
(48.2)
1224
(48.2)
1224
(48.2)
E1
mm
(in.)
168
(6.6)
213
(8.4)
213
(8.4)
283
(11.1)
283
(11.1)
283
(11.1)
E2
mm
(in.)
95
(3.7)
95
(3.7)
95
(3.7)
133
(5.2)
133
(5.2)
133
(5.2)
F1
mm
(in.)
45
(1.8)
45
(1.8)
45
(1.8)
F2
mm
(in.)
534
(21)
534
(21)
534
(21)
G1
mm
(in.)
60
(2.3)
70
(2.7)
70
(2.7)
70
(2.7)
70
(2.7)
70
(2.7)
G2
mm
(in.)
826
(32.5)
937
(36.9)
937
(36.9)
1095
(43.1)
1095
(43.1)
1095
(43.1)
H1
mm
(in.)
368
(14.5)
458
(18)
458
(18)
492
(19.4)
492
(19.4)
492
(19.4)
H2
mm
(in.)
1032
(42.6)
1140
(44.9)
1140
(44.9)
1330
(52.3)
1330
(52.3)
1330
(52.3)
I1
mm
(in.)
280
(11)
371
(14.6)
371
(14.6)
406
(16.0)
406
(16.0)
406
(16.0)
I2
mm
(in.)
1019
(40.1)
1130
(44.5)
1130
(44.5)
1317
(51.8)
1317
(51.8)
1317
(51.8)
J1
mm
(in.)
305
(12)
394
(15.5)
394
(15.5)
429
(16.8)
429
(16.8)
429
(16.8)
J2
mm
(in.)
1054
(41.5)
1155
(45.5)
1155
(45.5)
1343
(52.9)
1343
(52.9)
1343
(52.9)
J3
mm
(in.)
1019
(40.1)
1130
(44.5)
1130
(44.5)
1318
(51.8)
1318
(51.8)
1318
(51.8)
J2
C1
D1
B1
A1
J1
I1
H1
G1
C2
B2
D2
J3
H2
A2
G2
F2
E2
F1
E1
M3
I2
6
DIMENSIONS AND TECHNICAL SPECIFICATIONS
Dimensions
Crated Dimensions
Model
Crated Width
mm (in.)
Crated Depth
mm (in.)
Crated Height
mm (in.)
MYR20 705 (27.8) 841 (33.1) 1270 (50.0)
MYR25 800 (31.5) 880 (34.6) 1381 (54.4)
MYR30 800 (31.5) 991 (39.0) 1381 (54.4)
MYR40 940 (37.0) 1029 (40.5) 1560 (61.43)
MYR55 940 (37.0) 1169 (46.0) 1560 (61.4)
MYR65 940 (37.0) 1242 (48.9) 1560 (61.4)
Approximate Weight
Model Uncrated-kg (lb) Crated-kg (lb)
MYR20 151 (334) 166 (365)
MYR25 203 (447) 218 (480)
MYR30 222 (489) 237 (523)
MYR40 312 (688) 328 (724)
MYR55 332 (731) 349 (769)
MYR65 347 (764) 364 (802)
Water Heating (Factory Option Only)
Model
Electrical heating, optional alternate heating
element size-kW
MYR20 8 or 12
MYR25 8 or 12
MYR30 8 or 12
MYR40 16
MYR55 18
MYR65 18
7
DIMENSIONS AND TECHNICAL SPECIFICATIONS
Water, Drain, External Supply Connections
Model
Number
of water
inlets
Optional
third
water inlet
Inlet sizes
mm (in.)
Operating
Pressure
Bar (Psi)
Number of
dispenser
compartments
External
chemical
connections,
number
Drain valve
drain, Size
mm (in.)
Optional
Second
Drain Valve
MYR20 2 Yes 13 (1/2") 1-8 (20-120) 4 8 76 (3) NO
MYR25 2 Yes 13 (1/2") 1-8 (20-120) 4 8 76 (3) NO
MYR30 2 Yes 13 (1/2") 1-8 (20-120) 4 8 76 (3) NO
MYR40 2 Yes 13 (1/2") 1-8 (20-120) 4 8 76 (3) NO
MYR55 2 Yes 13 (1/2") 1-8 (20-120) 4 8 76 (3) YES
MYR65 2 Yes 13 (1/2") 1-8 (20-120) 4 8 76 (3) YES
Energy/Water Usage
Model
Average Cycle Water Use
lbs
Hot
Water
Total
Water
Total/Hot
Ratio
MYR20 20 4 11.7 2.925
MYR25 25 6 17.6 2.925
MYR30 30 8 23.4 2.925
MYR40 40 11 32.2 2.925
MYR55 55 14 41.0 2.925
MYR65 65 17 49.7 2.925
Gallons
8
INSTALLATION REQUIREMENTS
Tools and Parts
Parts supplied:
Water inlet hoses (2) Inlet hose washers (4) Service Keys
Drain Hose Hose clamp
9
LOCATION REQUIREMENTS
Forces transmitted by the washing machine
MYR20 MYR25 MYR30 MYR40 MYR55 MYR65
Static oor load (Kn - lb) 1.49 (334) 1.99 (447) 2.18 (489) 3.07 (688) 3.26 (731) 3.40 (764)
Dynamic oor load (Kn - lb) 2.42 (543) 4.01 (900) 5.12 (1150) 5.60 (1260) 7.52 (1690) 8.82 (1981)
Maximum vertical load (Kn - lb) 3.91 (877) 6.00 (1347) 7.30 (1639) 8.67 (1948) 10.80 (2421) 12.22 (2745)
Dynamic load frequency (Hz) 13.97 13.20 13.17 11.59 11.55 11.59
G factor 200 200 200 200 200 200
Anchorage points 4 4 4 8 8 8
Min Concrete Thk. (mm - in) 100 (4) 100 (4) 150 (6) 150 (6) 200 (8) 200 (8)
Loading...