Maytag MMC5000ADB, MMC5000ADW Installation Instructions
ยข
MicrowaveOvenBuilt-InKit
ModelsMK271andMK301
With use on Models M170 & MMC5000 Microwave Ovens.
STEP 1: ELECTRICAL REQUIREMENTS
OBSERVEALL GOVERNINGCODESAND ORDINANCES.
A.. A 120-Volt,60Hz,AC, 15ampere,fusedelectricalsupply
is required (time-delaYfuse or circuit breaker is
recommended).However,ifyourhomehasacircuitwired
and fusedfor 20 amperes,thisis preferred.If youare
installinga new circuit,one wired and fused for 20
amperesisrecommended.ItisaJsorecommendedthata
separatecircuitservingonlythisappliancebeprovided.
Donotuseanextensioncord.
B, ElectricalConnection
ELECTRICAL GROUND tS REQUIRED ON THIS
APPLIANCE. DO NOT UNDER ANY CIRCUM-
STANCES, REMOVE THE POWER SUPPLY CORD
GROUND PRONG.
LS
Foryourpersonalsafety, thisappliancemustbeproperly
groundedandpolarized.This applianceisequippedwith
a powersupplycord having a3-pronggroundingplug.To
minimize possible shock hazard, the cord must be
plugged into a mating 3-hole grounding type wall
receptacle, grounded in accordance with the National NOTE: A 27" minimum wide cabinet must be provide
ElectricalCode, local codesand ordinances.If a mating installTrim KitMK271.
wall receptacle is not available, it is the personal NOTE: A 30" minimum wide cabinet must be provide
responsibilityand obligation of the customer to have a
properlygrounded and polarized3-hole wall receptacle installTrim KitMK301.
installedby a qualifiedelectrician.(See figure1).
STEP 2: LOWER SUPPORT
A. Set microwave on its back so bottom is access
_. :i;: handscrewfrombottomfrontandattachlowersuppo
shownin figure2 withsamescrews.
Com :::
Grounding3-ProngPowerSupplyPlug--_ "/" !_ Remove left outboard screw and corresponding i.....
///
Required Grounding Method
ProperlyPolarized LOWER
3-H0JeGrounding
TypeWellReoeptm_e SUPPORT
FIGURE1
FIGURE2
STEP 3: CABINET OPENING
The opening should be per dimensions described below. All
corners should be square. The floor of the opening must be
plywood and must be level and capable of supporting 80 Ibs.
_j
MODEL DIM,"A"
16-1 . MK271 25-1/2"
_ _ . _ MK301 28-3/16_ FIGURE 5
\
. FIGURE 3 NOTE: When installing this kit above a built-in oven, che
INSTALLATION ABOVE LOWER OVEN
built-in oven installation instructions to determ
cutout dimensions for the (lower) wall oven.
NOTE: For a new installation, the 48" height dimension to
bottom of the cutout for the microwave oven
recommended. This places the microwave o_
bottom at approximately 50" from the floor. See fig_
STEP 4: ASSEMBLY OF INTAKE HOOD 6.
A. Remove lower left rear cabinet screw.
B. Place rear intake hood against rear of microwave.
C. Align hole in rear intake hood and microwave cabinet,
reinstall screw removed in step A.
D. Place top intake hood so hole at rear aligns with hole in
rear intake hood.
_. Install rear screw to attach top intake hood to rear intake I_ - _,,,,t,1
F. Install front shoulder screw through top intake hood into
SHOULDER SCREW INSTALLED
IN INTAKE HOOD FRONT
TAPE UNDER
FLANGE BOTH SIDES
hole in front of microwave cabinet (see figure 4). __ _
I IIIL...J_L
MK271Kits may be used with microwave model M]7
MMC5000 installed above 27' wall oven models bee
manufacturer No. E33658, when installed in accordance
[ FIGURE 4 Manufacturer's Installation Instructions. These inc
models W27100, W27200, W27400, CWE6800, CWE'68
STEP 5: INSTALLATION OF MICROWAVE OVEN
MK301 Kits may be used with microwave model MI?
A. Plug power cord of oven into receptacle. MMC5000 installed above 30" wall oven models bee
B. Slide the oven into the opening. Besure the lip of the lower manufacturer No. E33658, when installed in accordance
support isflush with front of cabinet. Center microwave in Manufacturer's Installation Instructions. These inc
opening, models W30100, W30400.
_. ._,ttachlower support to cabinet with 2 flat head screws.
D. Attach trim assembly as shown in figure 5. Insert bottom Manufacturer's No. can be obtained from the serial plat
of trim assembly into lower support and rotate upward, the wall oven.
Mark location of screw. Remove trim and drill 9/64 pilot
hole at marked locations and reinstall trim. Attach top of - IMPORTANT-
trim to cabinet with 2 flat head screws. SAVE FOR LOCAL ELECTRICAL INSPECTOR'S U
Loading...