Maytag MGT3800TW1, WGT3300SQ1, WGT3300SQ0, MGT3800TW0 Installation Guide

27"(69CM)GASWASHER/DRYER
INSTALLATIONINSTRUCTIONS
INSTRUCCIONESDE INSTALACIONDELALAVADORM
SECADORAAGASDE27'(69CM)
p
INSTRUCTIONSD'INST TION- LAVEUSE/SECHEUSEAGAZ
DE27'(69CM)
Table of Contents /Indice / Tabledes matDres
Teels and Parts ............................................. 3
Alternate Parts ............................................... 3
Location Requirements ................................ 3
Drain System ................................................. 4
Electrical Requirements ................................ 5
Gas Supply Requirements ............................ 5
Venting Requirements ................................... 6
Remove Shipping Strap ................................ 7
Install Leveling Legs ...................................... 8
Connect the Drain Hose ................................ 8
Connect the Inlet Hoses ............................... 8
Secure the Drain Hose .................................. 9
Plan Vent System ........................................ 10
Install Vent System ...................................... 11
Level Washer/Dryer ..................................... 11
Make Gas Connection ................................ 11
Connect Vent .............................................. 12
Complete Installation .................................. 12
SEGURIDAD DE LA
LAVADORA/SECADORA ............................... 13
INSTRUCCIONES DE INSTALACION .......... 14
Herramientas y piezas ................................. 14
Piezas altemativas ...................................... 14
Requisitos de ubicacion ............................. 14
Sistema de desagiJe .................................. 16
Requisitos el_ctricos ................................... 16
Requisitos del suministro de gas ................ 17
Requisitos de ventilaci6n ............................ 18
Quite el fleje de embalaje ............................ 19
Instalacion de las patas niveladoras ........... 20
Conecte la manguera de desagL_e.............. 20
Conecte las mangueras de entrada ........... 20
Fijacion de la manguera de desagiJe .......... 21
Planificaci6n del sistema de ventilaci6n ..... 22
Instalacion del sistema de ventilacion ........ 23
Como nivelar la lavadora/secadora ............ 23
Conexi6n del suministro de gas ................. 23
Conexi6n del ducto de escape ................... 24
Complete la instalaci6n ............................... 24
SleCURITle DE LA LAVEUSE/SleCHEUSE ... 25
INSTRUCTIONS D'INSTALLATION .............. 26
Outillage et pi_ces ....................................... 26
Autres pi_ces .............................................. 26
Exigences d'emplacement ........................ 26
Systeme de vidange ................................... 28
Specifications _lectriques ........................... 28
Specifications de I'alimentation en gaz ...... 29
Exigences concernant I'_vacuation ............ 30
Enlever la sangle d'exp_dition .................... 31
Installation des pieds de nivellement .......... 31
Raccordement du tuyau de vidange .......... 31
Raccordement des tuyaux d'alimentation.. 32
Immobilisation du tuyau de vidange ........... 33
Planification du systeme d'_vacuation ....... 33
Installation du systeme d'_vacuation ......... 35
Nivellement de la laveuse/s_cheuse ........... 35
Raccordement &la canalisation de gaz ...... 35
Conduit d'_vacuation .................................. 36
Achever I'installation ................................... 36
WASHER/DRYERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
W10118290A
IMPORTANT SAFETY INSTRUCTIONS
When discarding or storing your old clothes dryer, remove the door.
SAVE TH ESE INSTRUCTIONS
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
In the State of Massachusetts, the following installation instructions apply: [] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts. [] If using a ball valve, it shall be a T-handle type. [] A flexible gas connector, when used, must not exceed 3 feet.
iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.
INSTALLATIONINSTRUCTIONS
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed
here.
Tools needed:
8" or 10" adjustable wrench (for gas
connections) Flat-blade screwdriver
Adjustable wrench that opens to 1" (2.5 cm) or
9/16"(14 mm) open-end wrench (for adjusting washer/dryer feet)
Level 1/4"nut driver or socket
wrench (recommended) Wood block (for leveling)
Ruler or measuring tape
Parts supplied:
Remove parts package from the washer basket. Check that all parts are included.
Knife
Vent clamps
Pipe-joint compound resistant to LP gas
Caulking gun and compound (for installing
new exhaust vent) Pliers that open to
1%6" (3.95 cm) Scissors
Tin snips (new vent
installation)
Your installation may require additional parts. For information on ordering, please refer to the toll free phone numbers on the front page of the Washer/Dryer User Instructions.
If You Have You Will Need to Buy
Laundry tub or Sump pump system (if not already standpipe taller than available)
96" (2.4 m)
1" (2.5 cm) diameter 2" (5 cm) diameter to 1" (2.5 cm) standpipe diameter standpipe adapter, Part
Number 3363920
Overhead sewer Standard 20 gal. (76 L) 34" (86.4 cm)
tall drain tub or utility sink and sump
pump (available from local plumbing suppliers)
Floor drain Siphon break, Part Number 285320,
additional drain hose, Part Number 285702 and connector kit,
Part Number 285442
Drain hose too short Drain hose, Part Number 285664 and
connector kit, Part Number 285442
Lint clogged drain Drain protector, Part Number 367031
Water faucets 2 longer water fill hoses: beyond reach of fill 6 ft (1.8 m) Part Number 76314,
hoses 10 ft (3.0 m) Part Number 350008
D E
A. Water inlet hoses (2) B. Inlet hose flat washers (4) C. Front leveling feet with nuts (2) D. Shipping strap (net in parts bag,
see "Remove Shipping Strap")
E. Drain hose F Silver, double-wire hose clamp
Parts needed:
Check local codes and with gas supplier, check existing gas supply, electrical supply and venting, and read "Electrical
Requirements," "Gas Supply Requirements" and "Venting Requirements" before purchasing parts.
Mobile home installations require special parts (listed following) available for purchase from the dealer from whom you purchased
your dryer. For further information, please reference the "Assistance or Service" section of the Washer/Dryer User
Instructions.
Mobile Home Installation Kit. Ask for Part Number 346764.
Metal exhaust system hardware.
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer,
Failure to do so can result in death, explosion, or fire.
You will need
A location that allows for proper exhaust installation. A gas washer/dryer must be exhausted to the outdoors. See
"Venting Requirements."
A grounded electrical outlet located within 2 ft (61 cm) of either side of the washer/dryer. See "Electrical Requirements."
A sturdy floor to support the washer/dryer weight (washer/ dryer, water and load) of 500 Ibs (226.8 kg).
A level floor with a maximum slope of 1" (2.5 cm) under entire washer/dryer. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if washer/dryer is not
level. Installing on carpet is not recommended.
Awaterheatersettodeliver120°F(49°C)watertothewasher.
Hotandcoldwaterfaucetslocatedwithin4ft(1.2m)ofthe hotandcoldwaterfillvalves,andwaterpressureof5-100psi (34.5-689.6kPa).
Thewasher/dryermustnotbeinstalledorstoredinanareawhere itwillbeexposedtowaterand/orweather.
Donotoperateyourwasherintemperaturesatorbelow 32°F(0°C).Somewatercanremaininthewasherandcancause damageinlowtemperatures.See"Washer/DryerCare"inthe Washer/DryerUserInstructionsforwinterizinginformation.
Donotoperateyourdryerintemperaturesbelow45°F(7°C).At lowertemperatures,thedryermightnotshutoffattheendofan automaticcycle.Thiscanresultinlongerdryingtimes.
Checkcoderequirements.Somecodeslimit,ordonotpermit, installationofthewasher/dryeringarages,closets,mobilehomes,
orsleepingquarters.Contactyourlocalbuildinginspector. NOTE:Nootherfuel-burningappliancecanbeinstalledinthe
sameclosetasadryer.
Installation Clearances
The location must be large enough to allow the dryer door to open fully.
Washer/Dryer Dimensions
71%"
(181.9 cm)
*32"
(81.3 cm)
*Most installations require a minimum 5" (12.7 cm) clearance
behind the dryer for the exhaust vent with elbow. See "Venting Requirements."
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this washer/dryer. This washer/dryer has been tested for spacing of 0"
(0 cm) clearance on the sides. Recommended spacing should be considered for the following reasons:
Additional spacing should be considered for ease of installation and servicing.
Additional clearances might be required for wall, door and floor moldings.
Additional spacing on all sides of the laundry center is recommended to reduce noise transfer.
27"
(68.6 cm)
For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are acceptable.
0o.o0
II I
48in.2-
(310 cm2)
-NN-
#
24in.2-
m
r_,lJ27,H, I1_,,
(23 cm)
(63,6cm) (2,3cm)(2,3cm) (813cm) (12,7cm)
A B
*Required spacing
**Rear clearance may be 1" (2.5 cm) when house exhaust system
is lined up directly with dryer exhaust.
Mobile Home - Additional Installation Requirements This washer/dryer is suitable for mobile home installations.
The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH.
Mobile home installations require:
Metal exhaust system hardware, which is available for purchase from your dealer.
Mobile Home Installation Kit Part Number 346764. See "Tools and Parts" section for information on ordering.
Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.
The washer/dryer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need.
See "Alternate Parts."
Standpipe drain system - wall or floor (views A & B) The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. See "Alternate Parts."
The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (2.4 m) from the bottom of the washer.
--,---, _ (155crn2)
--_11"*_ 16"_-**
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
- (7.6 cm)
A B
Laundry tub drain system (view C} The laundry tub needs a minimum 20 gal. (76 L) capacity. The top
of the laundry tub must be at least 34" (86.4 cm) above the floor and no higher than 96" (2.4 m) from the bottom of the washer.
Floor drain system (view D) The floor drain system requires a siphon break that may be purchased separately. See "Alternate Parts."
The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed.
C
Do not have a fuse in the neutral or ground circuit.
GROUNDING iNSTRUCTIONS
[] For a grounded, cord-connected washer/dryer:
This washer/dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This washer/dryer is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with
all local codes and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the washer/dryer is properly grounded. Do not modify the plug provided with
the washer/dryer: if itwill not fit the outlet, have a proper
outlet installed by a qualified electrician.
SAVE THESE INSTRUCTIONS
Electrical Shock Hazard
Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.
Do not use an extension cord. Failure to follow these instructions can result in death,
fire, or electrical shock.
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is also recommended that a separate circuit
serving only this appliance be provided. To minimize possible shock hazard, the cord must be plugged
into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded
outlet installed by a qualified electrician. IMPORTANT: The washer/dryer must be electrically grounded
in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or with the Canadian Electrical Code, CSA C22.1.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the washer/dryer is properly grounded.
Explosion Hazard
Use a new CSA international approved gas supply line.
install a shut-off valve. Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (33 cm) water column.
Examples of a qualified person include: licensed heating personnel,
authorized gas company personnel, and authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Gas type
Natural Gas:
This washer/dryer is equipped for use with Natural gas. It is design-certified by CSA International for LP (propane or butane) gases with appropriate conversion.
Your washer/dryer must have the correct burner for the type of gas in your home. Burner information is located on the rating
plate in the door well of your dryer. Ifthis information does not agree with the type of gas available, contact your dealer or call
the phone numbers referenced on the front page of the Washer/Dryer User Instructions.
LP gas conversion: Conversion must be made by a qualified technician.
No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting your gas company.
Gas supply line
_sssssss/_
Gas supply pressure testing
Must include r/8"NPT minimum plugged tapping accessible for test gauge connection, immediately upstream of the gas
connection to the washer/dryer (see illustration).
r/2" IPS pipe is recommended.
3/8"approved aluminum or copper tubing is acceptable for lengths under 20 ft (6.1 m) if local codes and gas supplier
permit.
If you are using Natural gas, do not use copper tubing.
Lengths over 20 ft (6.1 m) should use larger tubing and a different size adapter fitting.
Gas supply line coupling must be 34" (86.4 cm) to 37" (94 cm) from the floor.
If your washer/dryer has been converted to use LP gas, %" LP compatible copper tubing can be used. If the total length of
the supply line is more than 20 ft (6.1 m), use larger pipe. NOTE: Pipe-joint compounds that resist the action of LP gas
must be used. Do not use TEFLON _ttape.
Must include a shutoff valve:
In the U.S.A.:
An individual manual shutoff valve must be installed within six (6) feet (1.8 m)of the dryer in accordance with the National
Fuel Gas Code, ANSI Z223.1. In Canada:
An individual manual shutoff valve must be installed in accordance with the B149.1, Natural Gas and Propane
Installation Code. It is recommended that an individual manual shutoff valve be installed within six (6) feet (1.8 m)
of the dryer. The location should be easy to reach for opening and closing.
.....................A
........... B
............ C
The washer/dryer must be disconnected from the gas supply piping system during pressure testing at pressures greater
than 1/2psi.
Dryer gas connection
This washer/dryer is equipped with its own permanent, flexible gas connector design-certified by CSA International,
for connecting the washer/dryer to the gas supply line.
--i
Flexible gas connector
Fire Hazard
Use a heavy metal vent. Do not use a plastic vent.
Do not use a metal foil vent. Failure to follow these instructions can result in death
or fire.
A. Gas shutoff valve B. Vs"NPT plugged tapping
C. Y2"NPT gas supply line D. Gas supply line coupling 34" (86.4 cm) min.
to 87" (94 cm) max. from floor
Burner input requirements
Elevations up to 10,000 ft (3,048 meters):
The design of this washer/dryer is certified by CSA International for use at altitudes up to 10,000 ft (3,048 m) above sea level at the Btu rating indicated on the model/serial number plate. Burner input adjustments are not required when the dryer is operated up to this elevation.
Elevations above 10,000 ft (3,048 meters):
When installed above 10,000 ft (3,048 m) a 4% reduction of the burner Btu rating shown on the model/serial number plate
is required for each 1,000 ft (305 m) increase in elevation.
1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
WARNING: To reduce the risk of fire, this washer/dryer
MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling or a concealed space of a building.
If using an existing vent system
Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.
Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.
Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance.
If this is a new vent system
Vent material
Use a heavy metal vent. Do not use plastic or metal foil vent.
4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFF Mventing products are recommended.
4" (!0.2 cm) heavymetal exhaust vent
DURASAFF Mvent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the "Assistance or Service" section of the Washer/Dryer User Instructions.
Rigid metal vent
For best drying performance, rigid metal vents are recommended.
Rigid metal vent is recommended to avoid crushing and kinking.
Flexible metal vent
Flexible metal vents are acceptable only if accessible for cleaning.
Flexible metal vent must be fully extended and supported when the dryer is in its final location.
Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor
performance.
Do not install flexible metal vent in enclosed walls, ceilings or floors.
Elbows
45° elbows provide better airflow than 90° elbows.
The angled hood style (shown here) is acceptable.
4-"
(10.2 c m)_._
_"_4,\ 2'/2"
(6.4 cm)
An exhaust hood should cap the vent to keep rodents and insects from entering the home.
Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).
Do not use an exhaust hood with a magnetic latch.
improper venting can cause moisture and lint to collect indoors, which may result in:
[] Moisture damage to woodwork, furniture, paint, wallpaper,
carpets, etc.
[] Housecleaning problems and health problems.
Excessive Weight Hazard
Use two or more people to move and install washer/dryer.
Failure to do so can result in back or other injury.
Good Better
Clamps
Use clamps to seal all joints.
Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct. Do not use duct tape.
Clamp
Exhaust
Recommended hood styles are shown here.
B
(10.2 cm)
A.Louvered hood style B.Box hood style
To avoid floor damage, set washer/dryer onto cardboard before moving across floor. Move washer/dryer close to its final location.
1. Do not cut yellow strap. Pull yellow strap firmly, until completely removed from washer/dryer. There should be
2 cotter pins on the end of the shipping strap. Remove the hang tag and pin from the vent pipe.
2. Tilt the washer/dryer forward. Move each of the 2 rear legs in an up-down motion to check the self-adjusting leveling legs
for free movement. This is required for proper leveling. Gently lower the washer/dryer to the floor.
3. Cut the shipping strap about 16" (40,6 cm) from the plug end. Look for the words "CUT HERE." Discard end with cotter pins.
You will use the remaining piece of shipping strap to secure the drain hose.
Install the front leveling feet
1. Prop up the front of the washer/dryer about 4" (10,2 cm) with
a wood block or similar object. The block needs to support the weight of the washer/dryer.
2. Screw the Iocknut onto each foot to within 1" (2.5 cm) of the base.
1 "
(2.5 cm)
4=
Open clamp, Twist hose back and forth while pushing onto drain connector on the side of the washer/dryer. Continue until
hose contacts the ribbed stops on the cabinet.
t
...... J
3. Screw the feet into the correct holes at the front corner of the washer/dryer until the nuts touch the washer.
NOTE: Do not tighten the nuts until the washer/dryer is level.
4. Tilt the washer/dryer back and remove the wood block, Gently lower the washer/dryer to the floor.
For mobile home use
Washer/dryers with gas dryers must be securely fastened to the floor.
Mobile home installations require a Mobile Home Installation Kit. See "Tools and Parts" section for information on ordering.
Proper connection of the drain hose protects your floors from damage due to water leakage. To keep the drain hose from
coming off or leaking, it must be installed according to the following instructions:
IMPORTANT: To ensure proper installation, this procedure must be followed exactly.
1. Check the drain hose to see whether it is the proper length.
2. Wet the inside of the straight end of the drain hose with tap water.
IMPORTANT: Do not use any lubricant other than wate£
3. Squeeze ears of the silver, double-wire clamp with pliers to open. Place clamp over the straight end of the drain hose 1A"(6.4 mm) from the end,
5. Place clamp over the area marked "CLAMR" Release clamp.
For laundry tub or standpipe drain systems
1. Make sure drain hose form is in correct position.
A. Drain hose form
2. Put hooked end of drain hose into laundry tub or standpipe. Rotate hook to eliminate kinks.
To keep drain water from going back into the washer:
Do not force excess drain hose into standpipe. Hose should be secure but loose enough to provide a gap for air.
Do not lay excess hose on the bottom of the laundry tub.
For use with floor drain
Do not install the drain hose form onto the corrugated drain hose, You may need additional parts. See Floor drain under "Tools and
Parts."
Insert a new flat washer into each end of the inlet hoses. Firmly seat the washers in the couplings.
(6.4 rnm)
A B
A. Coupling
B. Washer
Connect the inlet hoses to the water faucets Make sure the washer basket is empty.
1. Attach hose to the hot water faucet. Screw on coupling by hand until it is seated on the washer.
2. Attach hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer.
3. Usingpliers,tightenthecouplingswithanadditionaltwo- thirdsturn.
NOTE:Donotovertightenorusetapeorsealantsonthevalve. Damagetothevalvescanresult.
Clearthe water lines
Run water through both faucets and inlet hoses, into a bucket or laundry tub, drainpipe or bucket to get rid of particles in the water lines that might clog the inlet valve screens.
Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet.
Connect the inlet hoses to the washer
1. Attach the hot water hose to the bottom inlet valve. Attaching the hot water hose first makes it easier to tighten connection with pliers.
2. Screw on coupling by hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional two- thirds turn.
NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.
In the U.S.A.
If you are working in a closet or recessed area Move the washer/dryer into its final location and remove
cardboard from under washer/dryer. Remove the access panel by removing 3 Phillips-head screws and one bumper, located at the top of the access panel. Set panel, screw, and bumper aside. Complete hookup of water hoses. Replace access panel upon completion of washer/dryer installation.
J
Check for leaks
Turn on the water faucets and check for leaks. A small amount of water might enter the washer. You will drain this water later.
NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for
future reference.
If you connect only one water hose, you must cap off the remaining water inlet port.
Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.
The apparatus must be connected to the water faucets using the new hoses. Do not use old hoses.
1. Move the washer/dryer to its final location and remove any cardboard used to move the washer/dryer.
2. Locate the remaining piece of shipping strap. See "Remove Shipping Strap."
A. Cold water inlet valve (top) B. Hot water inlet valve (bottom)
In Canada
A. Cold water inlet valve (top) B. Hot water inlet valve (bottom)
4. Attach the cold water hose to the top inlet valve.
5. Screw on coupling by hand until it is seated on the washer.
6. Using pliers, tighten the couplings with an additional two- thirds turn.
NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.
Shipping strap
3=
Wrap the drain hose to the laundry tub leg or standpipe with the shipping strap (A or B below). Push fastener into the
nearest hole in the shipping strap (see illustration above).
B
If the water faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe. Tightly wrap the shipping strap around the water inlet hoses and the
drain hose (C above). Push fastener into the nearest hole in the shipping strap (see illustration above).
Choose your exhaust installation type
Recommended exhaust installations
Typical installations vent the dryer from the rear of the washer/ dryer. Other installations are possible.
A. Dryer E,Elbow B. Rigid metal or flexible metal vent E Clamps C. Clamps G. Elbow
D. Wall H. Exhaust hood
Optional exhaust installations
This washer/dryer can be converted to exhaust out the right or left side. To convert the washer/dryer, use Side Exhaust Kit
Part Number 279823. If your washer/dryer was previously exhausted from the right or left side, it can be converted to rear exhaust by using standard offset connections. Tocover the hole in
the side, one of the following plugs can be added: 692790 (white) 3977784 (biscuit)
Follow the instructions in the kit to install. Kits are available from the dealer from whom you purchased your washer/dryer.
/
"', ,j .................
A
A. Loop system with standard elbows B. Loop system with one offset and one standard elbow C. Vent system with one periscope (2" [5 cm] clearance)
NOTE: The following kits for close clearance alternate installations are available for purchase. Please reference the "Assistance or Service" section of the Washer/Dryer User Instructions.
Over-the-Top Installation: Part Number 4396028
Periscope Installation (For use with dryer vent to wall vent mismatch):
Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)
mismatch Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)
mismatch
Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.
C
A. Standard rear offset exhaust installation
B. Rear exhaust for offset close clearance connection C. Left or right side exhaust installation
Alternate installations for close clearances
Venting systems come in many varieties. Select the type best for your installation, Three close-clearance installations are shown. Refer to the manufacturer's instructions provided with the vent
system
10
Determine vent path
Select the route that will provide the straightest and most direct path outdoors.
Plan the installation to use the fewest number of elbows and turns,
When using elbows or making turns, allow as much room as possible.
Bend vent gradually to avoid kinking.
Use the fewest 90 ° turns possible.
Determine vent length and elbows needed for best drying performance
Use the Vent system chart below to determine type of vent
material and hood combinations acceptable to use. NOTE: Do not use vent runs longer than those specified in the
Vent system chart. Exhaust systems longer than those specified will:
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and increased energy usage.
The Vent system chart provides venting requirements that will help to achieve the best drying performance.
Vent system chart NOTE: Side exhaust installations add a 90° turn inside the dryer.
To determine maximum exhaust length, add one 90° turn to the chart.
Number of Type of Vent Box or Angled g0° turns Louvered hoods
or elbows hoods
0 Rigid metal 37 ft (11.3 m) 35 ft (10.7 m)
Flexible metal 25 ft (7.6 m) 20 ft (6.1 m)
1 Rigid metal 32 ft (9.7 m) 27 ft (8.2 m)
Flexible metal 21 ft (6.4 m) 16 ft (4.9 m)
2,
If the washer/dryer is not level, prop up the front with the wood block and adjust the feet up or down as necessary. Remove wood block.
3,
Tilt the washer/dryer forward until the rear of the washer/dryer is at least 4" (10.2 cm) off the floor. You may hear the self-
adjusting rear feet click into place. Lower the washer/dryer to the floor. Check the levelness of the washer/dryer with a level
as shown above. If washer/dryer will not level, recheck rear leveling legs for free
movement as described in the "Install Leveling Legs" section. Repeat until the washer/dryer is level.
NOTE: It may be necessary to level the washer/dryer again after it is moved into its final location.
4.
After the washer/dryer is in its final location and is level, use an adjustable or open-end wrench to turn the nuts on the front feet tightly against the washer cabinet.
If the nuts are not tight against the washer cabinet, the washer/dryer may vibrate.
2 Rigid metal 24 ft (7.3 m) 19 ft (5.8 m)
Flexible metal 15 ft (4.6 m) 10 ft (3.0 m)
1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.
2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.
3. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape,
screws or other fastening devices that extend into the interior of the vent to secure vent.
Properly leveling your washer/dryer avoids excessive noise and vibration.
1. Check the levelness of the washer/dryer by placing a level on the top edge of the washer, first side to side, then front to
back.
1,
Remove the red cap from the flexible gas connector.
2.
Remove the r/2" NPT adapter from the flexible gas connector. (it will be necessary to use two adjustable wrenches).
3,
Install the adapter on the 1/2"rigid gas supply pipe using pipe- joint compound.
A B _
E .................._
A. F2" rigid gas supply pipe B. Use pipe-joint compound. C. F2" NPT adapter D. Do not use pipe-joint compound. E. Flexible gas connector
NOTE: For LP gas connections, you must use pipe-joint compound resistant to the action of LP gas. De net use
TEFLON _>ttape.
1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
11
Loading...
+ 25 hidden pages