How it Works
Maytag
Loading...
MEW5524AS0
Installation Guide
16 pgs1.37 Mb0

Maytag MEW5524AS00, WOS52EM4AS00, MEW5524AS0 Installation Guide

INSTALLATIONINSTRUCTIONS
24" (60 CM) ELECTRICBUILT-INOVEN
INSTRUCTIONSD'INSTALLATION
FOURELECTRIQUEENCASTREDE24"(60 CM)
Table of Contents/Table des mati_res
BUILT-IN OVEN SAFETY ............................................................... 2
INSTALLATION REQUIREMENTS ................................................ 3
Tools and Parts ............................................................................ 3
Location Requirements ................................................................ 3
Electrical Requirements ............................................................... 4
INSTALLATION INSTRUCTIONS .................................................. 5
Prepare Built-In Oven ................................................................... 5
Remove Oven Door ...................................................................... 5
Make Electrical Connection ......................................................... 5
Install Oven ................................................................................... 7
Complete Installation ................................................................... 8
SI_CURITI_ DU FOUR ENCASTRI_ ................................................ 9
EXIGENCES D'INSTALLATION ................................................... 10
INSTRUCTIONS D'INSTALLATION ............................................. 13
Depose de la porte du four ........................................................ 13
Raccordement electrique ........................................................... 13
iMPORTANT:
Save for local electrical inspector's use.
iMPORTANT:
,&,conserver pour consultation par I'inspecteur local des installations 61ectriques.
501931002022
BUILT-INOVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
2
INSTALLATIONREQUIREMENTS
Gather the required tools and parts beforestarting installation. Read and follow the instructions provided with any tools listed
here.
Undercounter Installation (with cooktop installed above):
Ovens approved for this type of installation have an approval label located on the top of the oven. Refer to undercounter installation instructions for cutout dimensions and approved oven cooktop combinations (a separate sheet).
Tools needed
• Phillips screwdriver
• Flat-blade screwdriver
• Measuring tape
• Drill (for wall cabinet installations)
• 1" (2.5 cm) drill bit (for wall cabinet installations)
• Level
Parts needed
• CSA approved wire connectors
Parts supplied
• Two 4 x 25 mm self-tapping screws
• CSA approved conduit connector Check local codes. Check existing electrical supply. See
"Electrical Requirements." It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
_}CQ© :
IMPORTANT: Observe allgoverning codes and ordinances.
• Cabinet opening dimensions that are shown must beused. Given dimensions provide minimum clearance with oven.
• Recessed installation area must provide complete enclosure around the recessed portion of the oven.
• Grounded electrical supply isrequired. See "Electrical Requirements" section.
• Electrical supply junction box should be located 3" (7.6cm) maximum below the support surface when the oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should have beendrilled inthe right rear or left rear corner of the support surface to pass the appliance cable through to the junction box.
NOTE: For undercounter installation, it is recommended that the junction box be located in the adjacent right or left
cabinet. If you are installing the junction box on rear wall behind oven, the junction box must be recessed and located
in the upper or lower right or left corner ofthe cabinet to allow the oven to fit into the cabinet opening.
• Oven support surface must be solid, leveland flush with bottom of cabinet cutout. Floor must be able to support an oven weight of 140Ibs (63.5 kg).
IMPORTANT:Toavoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the
materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with
the requirements of OSAInternational and complies with the maximum allowable wood cabinet temperatures of 194°F
(90°0).
Product Dimensions
B
G
F
A. 21Y2" (54.5 cm) B. 3/4"(20 mm) C. 23Y2" (59.5 cm) D. 23Y2" (59.5 cm)
Cabinet Dimensions
IMPORTANT: The cabinet should be configured with openings as
shown in the following illustrations to allow the cooling system to work properly. Suggested dimenions of the openings are shown.
Arrows show the air circulation needed for proper cooling of the oven during operation.
Undercounter
A
A. 1_" (3.0 cm) maximum
B. 19_" (50.0 cm) minimum
C. 21 _" (55.0 cm) minimum
E. 22Y2" (57.2 cm)
F. 21 _" (53.8 cm)
G. 21 _" (53.7 cm)
E
D. 22" (56.0 cm) minimum
E. 235_ '' (60.0 cm) minimum
A. _/' (5mm)
Installed in Built-In Cabinet
Ifcodes permitand a separateground wireisused,itis
recommended that a qualified electrical installer determine that the ground path and the wire gauge are in accordance with local
codes. Check with a qualified electrical installer if you are not sure the
oven is properly grounded. This oven must be connected to a grounded metal, permanent
wiring system. Be sure that the electrical connection and wire size are adequate
and in conformance with the CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-1atest edition, and all local codes and ordinances.
C
A copy of the above code standards can be obtained from:
Canadian Standards Association
178 Rexdale Blvd.
Toronto, ON M9W 1R3 CANADA
Electrical Connection
To properly install your oven, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.
• Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located on the right vertical part of the oven frame. See the following
illustration.
B
A. 1_" (3.0 cm) maximum B. 19_" (50.0 cm) minimum C. 21 _" (55.0 cm) minimum
D. 22" (56.0 cm) minimum
E.23+ _" (58.3+0.2 mm)
A. Model/serial number plate
Models rated 3.6 kW and below at 120/240 volts require a separate 15-amp circuit. Models rated 3.6 to 4.8 kW at 120/240 volts require a separate 20-amp circuit.
A circuit breaker is recommended. Connect directly to the circuit breaker box (or fused
disconnect) through flexible, armored or nonmetallic sheathed, copper cable (with grounding wire). See "Make
Electrical Connection" section. CSA approved flexible conduit from the oven should be
connected directly to the junction box. Fuse both sides of the line.
Do not cut the conduit. The length of conduit provided is for serviceability of the oven.
A CSA approved conduit connector must be provided. If the house has aluminum wiring, follow the procedure
below:
1. Connect a section of solid copper wire to the ends of the
CSA approved flexible conduit leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed for joining copper to aluminum. Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
INSTALLATIONINSTRUCTIONS
1. Decide on the final location for the oven. Avoid drilling or cutting into house wiring during installation.
Excessive Weight Hazard
Use two or more people to move and install oven. Failure to do so can result in back or other injury.
2. To avoid floor damage, set the oven onto cardboard prior to installation. Do not use handle or any portion of the front frame for lifting.
3. Remove the shipping materials and tape from the oven.
4. Remove the hardware package from inside the bag containing literature.
5. Remove and set aside racks and other parts from inside the oven.
6. Move oven and cardboard close to the oven's final location.
n D
IMPORTANT" Use both hands to remove oven doors.
1. Open oven door all the way.
2. Flip up the hinge latch on each side.
3. Close the oven door as far as it will shut.
4. Lift the oven door while holding both sides. Continue to push the oven door closed and pull it away from
the oven door frame.
Electrical Shock Hazard
Disconnect power before servicing. Use 12 gauge solid copper wire.
Electrically ground oven. Failure to follow these instructions can result in death,
fire, or electrical shock.
This oven is manufactured with red and black power supply wires and a cabinet connected yellow/green wire twisted together. The oven is not supplied with a white neutral wire.
1. Disconnect power.
2. Remove terminal box cover screws.
_- !jA
..............................i f fij,_
IJ
A. Terminalbox cover screws B. Terminalbox cover
Loading...
+ 11 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use