Maytag MER6755ACS26, MER6755ACB24, MER6755ABW25, MER6755AAS26, MER6755AAB24 Owner’s Manual

YI AG

IVlaytag Electric Smoothtop

Double Oven Range

Precision Touch 750 Series

Warming Center

Controls Smoothtop Surface

Oven Cooking ......................... 8=17

Control Panel Baking

Cook & Hold Delay

Keep Warm

Toasting

Broiling Oven Racks

Form No. A/01/08 Part No. 8113P741-60 ¢c)2006 Maytag Appliances Sales Co. Litho U.S.A.

Maintenance ......................... 22=23

Oven Doors and Windows Oven Lights

Troubleshooting ................... 24=25

Warranty & Service .................... 27

Guide d'utilisation et

d'entretien ................................... 28

Gu[a de Uso y Cuidado ............. 56

Installer: Pleaseleave this guide with this appliance. Consumer: Pleaseread and keep this guide for future refer-

once, Keep sales receipt and/or canceled check as proof of purchase.

Model Number Serial Number

Date of Purchase If you have questions, call:

Customer Assistance 1-800-688=9900 USA

1-800-688-2002 Canada 1-800-688-2080 (U.S.TrY for hearing or speech impaired)

(Mon.-FrL 8 am-8 pm Eastern Time) Internet: http://wvvw, maytag.com

Inour continuing effort to improve the quality and performance ofour cooking products, it maybe necessaryto make changes

to the appliance without revising this guide. her service information, see page 27.

important$afe y

General Instructions

To ensure proper and safe operation: Appliance must be properly installed and grounded by a qualified techni- cian. Do not attempt to adjust, repair, service, or replace any part of your appliance unless it is specifically recom- mended in this guide. All other servicing should be referred to a qualified servicer.

Always disconnect power to appliance before servicing.

ALL RANGES CAN TiP AND

CAUSE INJURIES TO PERSONS INSTALL ANTI-TIP DEVICE

PACKED WITH RANGE FOLLOW ALL INSTALLATION

INSTRUCTIONS

WARNING: To reduce risk of tipping of the appliance from

abnormal usage or by excessive loading of the oven doors, the appliance must

be secured by a properly installed anti-tip device.

Warning and Important Safety Instructions appearing in this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution, and care must be exercised when installing, maintaining,

or operating the appliance.

Always contact your dealer, distributor, service agent, or

manufacturer about problems or conditions you do not understand.

Recognize Safety Symbols, Words, Labels

WARNING - Hazards or unsafe practices which

COULD result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which COULD result in minor personal injury.

Read and follow all instructions before using this appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a result of improper usage of the appliance. Use appliance only for its intended purpose as described in this guide.

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor when properly engaged. You should check this anytime the range has been moved.

in Case of Fire

Turn off appliance and ventilating hood to avoid spreading the flame. Extinguish flame then turn on hood to remove

smoke and odor.

• Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet. NEVER pick up or move a flaming pan.

• Ovens: Smother fire or flame by closing the oven doors.

Do not use water on grease fires. Use baking soda, a dry chemical or foam-type extinguisher to smother fire or

flame.

NEVER use an appliance as a step to reach cabinets above. Misuse of appliance doors, such as stepping, leaning or sitting on the door, may result in possible tipping of the appliance, breakage of door, and serious

injuries.

portentSefetyinstructions

If appliance is installed near a window, precautions should be taken to prevent curtains from blowing over surface ele-

ments. NEVER use appliance to warm or heat the room. Failure to

follow this instruction can lead to 3ossible burns, injury, fire, or damage to the appliance.

NEVER wear loose-fitting or hanging garments while using the appliance. Clothing could catch utensil handles or ignite and cause burns if garment comes in contact with hot heating elements.

To ensure proper operation and to avoid damage to the appliance or possible injury, do not adjust, service, repair or replace any part of the appliance unless specifically recom- mended in this guide. Refer all other servicing to a qualified

technician. NEVER store or use gasoline or other combustible or flam-

mable materials in the ovens, near surface units or in the vicinity of this appliance as fumes could create a fire hazard or an explosion.

To prevent grease fires, do not let cooking grease or other flammable materials accumulate in or near the appliance.

Use only dry potholders. Moist or damp potholders on hot surfaces may result in a steam burn. Do not let potholders touch hot heating elements. Do not use a towel or other bulky cloth which could easily touch hot heating elements and ignite.

Always turn off all controls when cooking is completed. NEVER heat unopened containers on the surface unit or in

the ovens. Pressure build-up in the container may cause container to burst resulting in burns, injury or damage to the appliance.

NEVER use aluminum foil to line drip bowls or cover oven racks or oven bottoms. This could result in risk of electric

shock, fire, or damage to the appliance. Use foil only as directed in this guide.

Aerosol-type cans are EXPLOSIVEwhen exposed to heat and may be highly flammable. Do not use or store near appliance.

Cooktop

NEVER leave surface units unattended especially when

using high heat. An unattended boilover could cause smok- ing and a greasy spillover can cause a fire.

This appliance is equipped with different size surface ele- ments. Select pans with flat bottoms large enough to cover element. Fitting pan size to element will improve cooking efficiency.

If pan is smaller than element, a portion of the element will be exposed to direct contact and could ignite clothing or potholder.

Only certain types of glass, glass-ceramic, ceramic, earthen- ware, or other glazed utensils are suitable for cooktop or oven service without breaking due to the sudden change in temperature. Follow utensil manufacturer's instructions when using glass.

This appliance has been tested for safe performance using conventional cookware. Do not use any devices or accesso- ries that are not specifically recommended in this manual.

Do not use stove top grills or add-on oven convection systems. The use of devices or accessories that are not expressly recommended in this manual can create serious safety hazards, result in performance problems, and reduce the life of the components of this appliance.

Turn pan handle toward center of cooktop, not out into the room or over another surface element. This reduces the risk

of burns, ignition of flammable materials, or spillage if pan is accidently bumped or reached by small children.

Glass=Ceramic Cooktop

NEVER cook on broken cooktop. If cooktop should break, cleaning solutions and spillovers may penetrate the broken cooktop and create a risk of electric shock. Contact a qualified technician immediately.

Clean cooktop with caution. Some cleaners can produce noxious fumes if applied to a hot surface. If a wet sponge, cloth, or paper towel is used on a hot cooking area, be

careful to avoid steam burn.

Heating Elements

NEVER touch surface or oven heating elements, areas near

elements, or interiorsurfaces of ovens.

Heating elements may be hot even though they are dark in color. Areas near surface elements and interior surfaces of

the ovens may become hot enough to cause burns. During and after use, do not touch or let clothing or other flam-

mable materials contact heating elements, areas near elements, or interior surfaces of ovens until they have had

sufficient time to cool. Other potentially hot surfaces include: Cooktop, areas facing

the cooktop, oven vent, and surfaces near the vent opening, oven doors, areas around the doors and oven windows.

ImportemSefety

Deep Fat Fryers

Use extreme caution when moving the grease pan or disposing of hot grease. Allow grease to cool before at- tempting to move pan.

Ovens

Use care when opening doors. Let hot air or steam escape before removing or replacing food.

For proper oven operation and performance, do not block or obstruct oven vent duct. When ovens are in use, the vent

and surrounding area near the vent may become hot enough to cause burns,

Always place oven racks in desired locations while ovens are cool, If rack must be moved while an oven is hot, do

not let potholder contact hot element in oven,

Self-Cleaning Ovens

Before self-cleaning the oven, remove the oven racks, broiler pan, food and any other utensils. Wipe spillovers to prevent excessive smoke and flare-ups.

Clean only parts listed in this guide. Do not clean door gasket. The gasket is essential for a good seal, Do not rub. damage. or move the gasket.

Do not use oven cleaners, No commercial oven cleaner or oven liner protective coating of any kind should be used in or

around any part of the ovens, Wipe up excessive spillovers, especially greasy spills, before

the clean cycle to prevent smoking, flare-ups or flaming. It is normal for the cooktop to become hot during a clean

cycle, Therefore. avoid touching the cooktop, door. window or oven vent during a clean cycle,

Child Safety

NEVER store itemsof interestto children in cabinets above an appliance. Children climbing on the appliance or on the

appliance doors to reach itemscould be seriously injured.

NEVER leave children alone or unsupervised in area where appliance is in use or isstill hot.

NEVER allow children to sit or stand on any part of the appliance as they could be injured or burned.

Children must be taught that the appliance and utensils in or on it can be hot. Let hot utensils cool in a safe place, out of reach of small children, Children should be taught that an appliance is not a toy. Children should not be allowed to play with controls or other parts of the unit.

Ventilating Hoods

Clean range hood and filters frequently to prevent grease or other flammable materials from accumulating on hood or filter and to avoid grease fires,

Turn the fan on when flamb6ing foods (such as Cherries Jubilee) under the hood.

important Safety Notice and

Warning

The California Safe Drinking Water and Toxic Enforce- ment Act of 1986 (Proposition 65:)requires the Governor of California to publish a list of substances known to the State of California to cause cancer or reproductive harm. and requires businesses to warn customers of potential exposures to such substances.

Users of this appliance are hereby warned that when the oven is engaged in the self-clean cycle, there may be some low-level exposure to some of the listed sub- stances, including carbon monoxide, Exposure to these substances can be minimized by properly venting the oven to the outdoors by opening the windows and/or door in the room where the appliance is located during the self-clean cycle,

IMPORTANT NOTICE REGARDING PET BIRDS: Never keep pet birds in the kitchen or in rooms where the

fumes from the kitchen could reach. Birds have a very sensitive respiratory system. Fumes released during an oven self-cleaning cycle may be harmful or fatal to birds,

Fumes released due to overheated cooking oil, fat, margarine and overheated non-stick cookware may be equally harmful,

Save These Instructions for

Future Reference

$urfece 9

Surface Controls

Use to turn on the surface elements. An infinite choice of heat settings _savadable from Low to High, The knobs can

be set on or between any of the settnlgs.

Setting the Controls

1. Place pan on surface element.

2. Push =r]and turn the knob =r_e_therd=rect=onto the desired heat settn_g.

- The control panel is marked to ident_fywhlch O O

element the knob controls. For example, the oO_-_,_, graph=cat nght nld=catesleft front element.

3. There _san element "ON" indicator light on the control panel. When any surface control knob =sturned on, the

hght wdl turn on. The hght will turn off when all the surface elements are turned off.

4, After cooknlg, turn knob to OFF, Remove pan,

Dual Elements (select models:)

The cooking surface has two dual elements located m the nght front and left front of the smoothtop. Th_sallows

you to change the s_zeof these elements. Turn control knob to OFF

before switching element s_ze. Press the sw_tch to the left to use the

large element or to the nght to use the small element.

OFF

Medium

Suggested Heat Settings

The s_ze,type of cookware and cooking operation wdl affect the heat setting. For ndormat_onon cookware and other

factors affectnlg heat settings, refer to Cookware

Recommendations on page 7.

Low (2): Use to keep foods 1

warn] and melt chocolate I and butter.

Use tocontinue cookingcovered

foodsorsteam

Med. Low (3=4): i

foods.

Medium (5=7): Use to manltam slow bod for

large amounts of hqLndS and for most frying

operations.

High (10): Use to bnng hquld to a bod. Always

reduce setting to a lower heat when hqLHdsbegnl to

bod or foods begnl to cook.

OFF [

Medium

Med. High (8-9): Use

to brown meat, heat od for deep fat frying or

sauteing. Maintain fast bod for large amounts

of hqLnds.

BEFORE COOKING

• Always place a pan on the surface unit before you turn it on.To prevent damage to range, never operate surface

unit without a pan in place.

, NEVER use the cooktop as a storage area for food or

cookware.

DURING COOKING

* Be sure you know which knob controls which surface

unit. Make sure you turned on the correct surface unit.

- Begin cooking on a higher heat setting then reduce to a lower setting to complete the operation. Never use a

high heat setting for extended cooking.

* NEVER allow a pan to boil dry. This could damage the

pan and the appliance.

° NEVERtouch cooktop until it has cooled. Expect some

parts of the cooktop, especially around the surface units,

to become warm or hot dunng cooking. Use potholders to protect hands.

AFTER COOKING

• Make sure surface unit is turned off.

• Clean up messyspills as soon as possible. OTHER TIPS

• If cabinet storage is provided directly above cooking surface, limit it to items that are infrequently used and can be safely stored in an area subjected to heat. Tempera-

tures may be unsafe for items such as volatile liquids, cleaners or aerosol sprays.

• NEVER leave any items, especially plastic items,on the cooktop. The hot air from the vent may ignite flammable

items, melt or soften plastics, or increase pressure in closed containers causing them to burst.

• NEVER allow aluminum foil, meat probes or any other metal object, other than a pan on a surface element, to

contact heating elements.

• NEVER store heavy items above the cooktop that could fall and damage it.

Surfece¢ookin:

Smoothtop Surface

Smoothtop Surface Notes:

* For Canadian models, the smoothtop does NOT operate

during a clean cycle.

* Cooktop may emit light smoke and odor the first few

times the cooktop is used. This isnormal.

* Smoothtop cooktops retain heat for a period of time

after the element is turned off. Turn the elements off

a few minutes before food is completely cooked and use

the retained heat to complete cooking. When the Hot Surface indicator light turns off, the cooking area will be

cool enough to touch. Because of the way they retain heat, the smoothtop elements will not respond to

changes in settings as quickly as coil elements.

* In the event of a potential boilover, remove the pan from

the cooking surface.

* Never attempt to lift the cooktop. * The smoothtop surface may appear discolored when it is

hot. This isnormal and will disappear when the surface cools.

Hot Surface Light

The Hot Surface indicator light is located on the control panel. The light will be illuminated

when any cooking area is hot. It will remain on, even after the control isturned off, until the area has cooled.

Warming Center ([selectmodels)

Use the Warming Center to keep hot cooked foods

warm, such as vegetables, gravies and oven-safe

dinner plates.

Setting the Control:

Press switch up to turn off or down to activate.

Notes:

* Never warm food for longer than one hour (eggs for 30

minutes), as food quality may deteriorate.

* Do not heat cold food on the Warming Center. * Warming temperatures of the food will vary depending

on type and amount of food. Always hold food at proper

food temperatures. USDA recommends food tempera- tures between 140°-170° F.

Hot Surface

OFF

Cooking Areas

The cooking areas on your range are identified by permanent circles on the smoothtop surface. For most efficient cooking,

fit the pan size to the element size.

Pans should not extend mere than 1/2to 1=inch beyond the cooking area.

When a control is turned on, a glow can be seen through the smoothtop surface. The element will cycle on and off to maintain the preset heat setting, even on High.

For more information on cookware, refer to Cookware Recommendations on page 7.

SINGLE _ _ WARMING CENTER

_,___________________ _=,_ _ ) -- " f- _ SINGLE

(style varies by model)

Warming Center Notes:

* Use only cookware and dishes recommended as safe for

oven and cooktop use.

* Always use oven mitts when removing food from the

Warming Center as cookware and plates will be hot.

* All foods should be covered with a lid or aluminum foil to

maintain food quality.

* When warming pastries and breads the cover should have

an opening to allow moisture to escape.

* Do not use plastic wrap to cover foods. Plastic may melt

on to the surface and be very difficult to clean.

SurfeceCooking

Tips to Protect the Smoothtop Surface

Cleaning (see page 20 for more information) * Before first use, clean the cooktop.

Clean your cooktop daily or after each use.This will keep your cooktop looking good and can prevent damage.

If a spillover occurs while cooking, immediatelyclean the spill from the cooking area while it is hot to prevent a tough

cleaning chore later. Using extreme care, wipe spill with a clean dry towel.

Do not allow spills to remain on the cooking area or the cooktop trim for a long period of time.

Never use abrasive cleansing powders or scouring pads which will scratch the cooktop.

Never use chlorine bleach, ammonia or other cleansers not specifically recommended for use on glass-ceramic.

To Prevent Marks & Scratches

', Do not use glass pans. They may scratch the surface.

Never place a trivet or wok ring between the surface and pan. These items can mark or etch the top.

Do not slide aluminum pans across a hot surface. The pans may leave marks which need to be removed promptly. (See

Cleaning, page 20.) Make sure the surface and the pan bottom are clean before

turning on to prevent scratches.

To prevent scratching or damage to the glass-ceramic top,

do not leave sugar, salt or fats on the cooking area. Wipe the cooktop surface with a clean cloth or paper towel

before using. Never slide heavy metal pans across the surface since

these may scratch.

To Prevent Stains

,, Never use a soiled dish cloth or sponge to clean the

cooktop surface. A film will remain which may cause stains on the cooking surface after the area is heated.

Continuously cooking on a soiled surface may/will result in a permanent stain.

To Prevent Other Damage

,, Do not allow plastic, sugar or foods with high sugar content

to melt onto the hot cooktop. Should this happen, clean immediately. (See Cleaning, page 20.)

Never let a pan boil dry as this will damage the surface and pan.

Never use cooktop as a work surface or cutting board. Never cook food directly on the surface.

Do not use a small pan on a large element. Not only does this waste energy, but it can also result in spillovers burning

onto the cooking area which requires extra cleaning. Do not use non-flat specialty items that are oversized or

uneven such as round bottom woks, rippled bottom and/or oversized canners and griddles.

Do not use foil or foil-type containers. Foil may melt onto the glass. If metal melts on the cooktop, do not use. Call an

authorized Maytag Servicer.

Surfece¢ookin:

Cookware Recommendations

Using the right cookware can prevent many problems, such

as food taking longer to cook or achieving inconsistent

results. Proper pans will reduce cooking times, use less

energy, and cook food more evenly.

Fiat Pan Tests

See if your pans are flat.

The Ruler Test:

1. Place a ruler across the bottom of the pan.

2. Hold it up to the light.

3. Little or no light should be visible under the ruler.

The Bubble Test:

1. Put 1 inch of water in the pan. Place on cooktop and turn control to High.

2. Watch the formation of the bubbles as the water heats. Uniform bubbles mean good performance, and uneven

bubbles indicate hot spots and uneven cooking.

Canning and Oversize

Cookware

All canners and large pots must have flat bottoms and must be made from heavy=gauge materials. This is critical

on smoothtop surfaces. The base must not be more than

1 inch larger than the element.

When canners and pots do not meet these standards, cooking times may be longer, and cooktops may be damaged.

Some canners are designed with smaller bases for use on smoothtop surfaces.

When canning, use the High heat setting only until the water comes to a boil or pressure is reached in the canner.

Reduce to the lowest heat setting that maintains the boil or pressure. If the heat is not turned down, the cooktop may be

damaged.

Flat,smooth-bottom Panswith grooved or warped bottoms. pans. Panswith uneven bottoms do not cook

efficiently and sometimes may not boil liquid.

Heavy-gauge pans. Pansthat are the

same size as the

element.

Secure handles. Cookware with loose or broken handles.

Tight-fitting lids. Loose-fitting lids.

Flat bottom woks. Woks with a ring-stand bottom.

Very thin-gauge metal or glass pans.

Panssmaller or larger than the

element by 1 inch.

Heavyhandles that tilt the pan.

Control Panel

A B C D E

Clean

Bake Toast

Keep ............

Warm ........Upper Oven

\\ C_NCE_ ......

Clean ............ _

....... Broil ....

Bake

Keep

Lower Oven Warm

...................@N

F G

Thecontrol panel is designed for easein programming. Thedisplaywindow onthecontrol shows time ofday,timer and ovenfunctions. Control panel shown includes model specific features. (Styling may vary depending on model.)

iii!Aiiiil

Bake

ii!B!iiiiii

Keep Warm

iiiiCiiiii

BmiI

iiiiBiiiiii

Toast

iiiiiiiiiiiiiiiiiii_i

Clean Delay

Cook & Hold

Timer

iiii|iiiiiiiiii!!;

Clock

ii:iJiiiiiiii!:

Oven Light Less-/More+

i;i;i;i!Liiiiiiii:iliiiii

CANCEL

Usefor baking and roasting. Use to keep cooked food warm in oven. Usefor broiling and top browning.

Usefor toasting bread and products

toasted in toaster or toaster oven.

Use to set self-clean cycle. Programsthe oven to start baking or

cleaning at a later time.

Bakes for a preset time, then keeps food

warm for 1 hour. Sets timer.

Use to set time-of-day clock. Useto turn the oven lights on or off. Enters or changes time, oven

temperature. Sets HI or LO broil. Cancels all operations except timer

and clock.

Using the Touchpads

* Pressthe desired pad.

Press More+ or Less- pad to enter time or temperature.

A beep will sound when any pad is touched. A double beep will sound if a programming error occurs.

Note: Four seconds after pressing the More+ or Less- pad, the time or temperature will automatically be entered.

If more than 30 seconds elapse between touching a function pad and the More+ or Less- pad, the function will

be canceled and the display will return to the previous display.

H | J K L

Clock

The clock can be set to display time in a 12-hour or 24-hour format. The clock isset at the factory for the 12-hour format.

To change the clock to 24=hour format:

1. Press and hold the Upper Oven CANCEL and Delay pads for several seconds.

Press the More+ or Less - pad to select 12 or 24 hour.

Set the time of day following the

directions below.

To set the Clock:

1. Pressthe Clock pad.

The colon (:) flashes in the display.

Press More+ or Less- pad to setthe time of day.

, CoIon continuesflashing.

When electrical power is supplied or after a power

interruption,the last clock time before power was interruptedwill flash.

To recall the time of day when another time function is showing, press the Clock pad.

Clock time cannot be changed when the oven has been programmed for Bake, Clean, Delay or Cook & Hold.

thoO,oc wa,t s conOs.

, The colon stops flashing.

cont.

To cancel the Clock display:

If you do not want the time of day to display: Press and hold the Upper Oven CANCEL

and Clock pads for several seconds. The time of day will disappear from the display.

When the clock display is canceled, press the Clock pad to briefly display the time of day.

To restore the Clock display:

Press and hold the Upper Oven CANCEL and Clock pads for several seconds. The time of day will reappear in the display.

Timer

The timer can be set from one minute (1:00:}up to 11 hours and 59 minutes (11:59:}.

The timer can be used independently of any other oven activity. It can also be set while another oven function is

operating. The timer does not control the oven.

To set the Timer:

Pressthe Timer pad.

"0:00" lights in the display. "Timer" will flash.

2. Pressthe More+ or Less- pad until the correct time appears in the display.

, "Timer" will continue to flash.

3. PressTimer pad again or wait four seconds. , The time begins counting down.

, The last minute of the timer countdown will be displayed

as seconds.

4. At the end of the set time, three long beeps will sound.

To cancel the Timer:

1. Press and hold the Timer pad for three seconds. OR

2. Pressthe Timer pad and set the time to 0:00.

Locking the Control

and Oven Doors

The touchpads and oven doors can be lockedfor safety, cleaning, or to prevent unwanted use. They will not function

when locked. If the oven is currently in use, the touchpads and doors

cannot be locked. The current time of day will remain in the display when the

controls are locked.

To lock both doors:

Press and hold the Upper Oven CANCEL and Cook & Hold pads for three seconds.

"Lock" flashes in the display while both oven doors lock. Once complete, "Lock"

stops flashing. "OFF"is displayed for 10 seconds whenever a pad is touched.

To unlock both doors:

Press and hold the Upper Oven CANCEL and Cook & Hold pads for three seconds.

"Lock" flashes and then disappears from the display. "OFF"appears in the display for several seconds while

doors are unlocking.

Note: The touchpads and oven doors cannot be locked if

the oven temperature is 400° F or above.

Fault Codes

"Bake" or "Lock" may flash rapidly in the display to alert you if there is an error or a problem. If "Bake" or "Lock" flash in the

display, press CANCEL pad. If "Bake" or "Lock" continue to flash, disconnect power to the appliance. Wait a few minutes,

and then reconnect power. If the flashing still continues, disconnect power to the appliance and call an authorized

servicer.

Adjusting the Sound Level

The factory default setting for sound is medium (IVIEd:},but it

can be changed to low (Lo:}or high (HI:}. To change the setting:

1. Press and hold More+ and upper oven CANCEL pads for three seconds. A beep will sound and the current sound

level ("Lo", "MEd" or "HI":}will appear in the display.

Press More+ pad to increase sound level or the Less- pad

to decrease sound level.

3. Wait four seconds and the new setting will be accepted.

4. If the More+ or Less- pad is not pressed within 30 sec- onds, the control will return to the existing settings.

Changing Temp °F/°C

The factory default setting for temperature is Fahrenheit. To change the setting:

1. Press and hold the upper oven Bake and CANCEL pads for three seconds. A beep will sound and the current setting

(°For °C:} will appear in the display.

Pressthe More+ or Less- pad to change the setting between °Fand °C.

Wait four seconds and the new setting will be accepted.

4. IftheMore+orLess-padisnotpressedwithin30sec- onds,thecontrolwillreturntotheexistingsettings.

Return To Factory Default

Settings

The control can be reset to the factory default settings. To return to the default settings:

1. Press and hold upper oven Keep Warm and CANCEL pads

for three seconds. A single beep will sound and "dEF"

(defaul0 will appear in the display.

2. Pressthe More+ pad to choose the factory settings. "cLr" (clea0 will appear in the display.

3. Wait four seconds and the factory settings will be accepted.

4. If the More+ or Less- pad is not pressed within 30 seconds,

the control will return to the existing settings.

To change the oven temperature during preheat, press

Bake once and reset temperature. Placefood in the oven.5.

6. Check cooking progress at minumum cooking time. Cook longer if needed.

7. When cooking isfinished, press (_AIXI('FI_ CANCEL pad.

8. Remove food from the oven.

Baking Differences Between Your Old

and New Oven

It isnormal to notice some baking time differences between a new oven and an old one. See"Adjusting the OvenTemperature"

on page 15.

Baking Notes:

Setting Upper and Lower Oven Functions

Baking

To set bake:

1. Pressthe Bake pad for desired oven.

. "Bake" will flash. . "000°'' will flash in the display.

2. Select the oven temperature. The oven tempera- ture can be set from 170° to 550°. Pressor press

and hold the More+ or Less- pad.

. "350°" will light when either pad is first pressed. . Press the More+ pad to increase the temperature. . Press the Less- pad to decrease the temperature.

3. Press Bake pad again or wait four seconds.

. "Bake" will stop flashing and light in the display. . "Preheat" will light in the display. . 100° or the actual oven temperature will display. The

temperature will rise in 5° increments until the preset temperature is reached.

.... ....

. Ifthe lower oven is NOTin use,the upper oven will

preheat more quickly.

. Allow at least 1/2=inch between the baking pan or

casserole and the top element in the upper oven.

Loaf, angel food or bundt pans are not recommended in

the upper oven.

• Do not use temperatures below 140° Fto keep food warm or below 200° Ffor cooking. Forfood safety reasons, lower

temperatures are not recommended.

. The back part of the lower oven bake element will NOT

glow red during baking. This is normal.

. When baking frozen, self-rise pizzas in the upper oven,

place the pizza on a cookie sheet to avoid overbrowning.

. When preheating with a baking/pizza stone inside

the upper oven, do not set oven above 400 ° F. To use

baking/pizza stones at temperatures above 400 ° in

the upper oven, put stone in after the preheat beep.

. To change the oven temperature during cooking, press the

Bake pad and then the More+ or Less- pad until you reach the desired temperature.

. Ifyou forget to turn off the oven, it will automatically turn

off at the end of 12 hours. Ifyou wish to deactivate the

Automatic Shut-Off/Sabbath Mode feature, see page 14.

4. Allow 4-10 minutes for upper oven to preheat and 7-12 minutes for lower oven to preheat.

. When the set oven temperature is reached, one long

beep will sound.

. To recall the set temperature during preheat, press the

Bake pad.

Cook & Hold

Cook & Hold allows you to bake for a preset amount of time, followed by a one-hour Keep Warm cycle.

To set Cook & Hold:

1. Press the Cook & Hold pad once for upper oven or twice for lower oven.

. "Bake" and "Hold" flash. . "000°'' will flash in the display.

cont.

Cookin

2. Selecttheoventemperature.The oven

temperature can be setfrom170 ° to 550°. pad:

Press or press and hold the More+ or Less- , Press the More+ pad to increase the

temperature.

, Press the Less- pad to decrease the temperature.

3. Press Cook & Hold pad again ORwait four seconds to set cook time.

, "Time" flashes. , "9:99" flashes in the display

4. Enter the amount of time you want to cook by pressing the More+ or Less- pad. Time can be set from 19 minutes

(19:99} to 11 hours, 59 minutes (11:59}. , "Bake", "Preheat" and "Hold" light in the display.

, The cooking time will start counting down. , "199°" or actual oven temperature will light in the

display.

To set a Delayed Baking cycle:

1. Pressthe Delay pad once for upper oven or twice for lower oven.

"dLY" and "9:99" flash inthe display.

2. Pressthe More+ or Less- pad to set the amount of time you want to delay the

Cook & Hold cycle.

While "dLY" is still flashing:

3. Pressthe Cook & Hold pad.

, "999°'' flashes inthe display. , "Bake" and "Hold" flash.

4. Press More+ or Less- pad to enter the oven temperature.

, "Bake" flashes. , After several seconds, "9:99" and "Time" flash.

, "Bake" and "Hold" remain steady.

5. Press More+ or Less- pad to set the baking time.

, "Time" flashes. , After several seconds, the delay time will count down. , "dLY", "Bake" and "Hold" light in the display.

When the cooking time has elapsed:

, Three beeps will sound. , "Bake" will turn off.

, "Hold" will light.

After one hour in HOLD WARM:

, The oven will turn off. Three beeps will sound.

To cancel Cook & Hold at any time: ¢(_ANffFI_

Pressthe CANCEL pad. Remove food from oven.

Delay Cook & Hold

When using Delay, the oven begins to cook later in the day. Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time, then keeps food warm for one hour.

Delay time can be set from 10 minutes (19:99} to 11 hours, 59 minutes (11:59}.

When the Delay time has expired:

, "dLY" will turn off. , Baking time and temperature are displayed.

, "Bake" and "Hold" are displayed.

When the oven starts:

, The baking time will count down. , "dLY" will turn off.

, "Bake" and "Hold" will remain lit.

To cancel:

Press the CANCEL pad.

All timed and untimed cooking functions will be canceled.

The time of day will reappear in the display.

Notes:

Do not use delayed baking for items that require a preheated oven, such as cakes, cookies, and breads.

Do not use delayed baking if oven is already hot.

Cookin_ g

Keep Warm

For safely keeping foods warm or for warming breads and plates.

To set Keep Warm:

1. Pressthe Keep Warm pad for the appropriate oven.

. "Warm" flashes. . "000°'' flashes in the display.

2. Select the Keep Warm temperature. The Keep

Warm temperature can be set from 145° to

190°.Pressor press and hold the More+ or Less- pad.

.170 ° will light when either pad is first pressed. . Press the More+ pad to increase the temperature.

. Press the Less- pad to decrease the temperature.

"Warm" and the temperature will be displayed while Keep

Warm is active.

Keep

Toasting (upper oven only:)

Fortoasting bread and products that are toasted in a toaster or

toaster oven. Toast time can be set from 10 seconds up to six

minutes.

1. Press the Toast pad. ., /,___:_ _..;..._,,.i..

2. Select the toasting time. Press .._;I.i!_ ::f-! ! il ....

the More+ pad to increase ..',_._,_-_,'..fj._, _,t_>'_-_'_-'_-_',._'..'.

• i,,,i" ', _7_ _1_._ _, '.'.

the time or press the Less- KJ_'[ __ ........:t _ : '_t_

pad to decrease the time. . "Toast" and the toasting

time will be displayed. The toasting time will begin to count down.

Browning time may vary, watch toasting carefully to avoid over-browning. Close oven door during toasting.

3. At the end of the set toasting time, the oven will beep.

• , , , ,,,, , ,J , , ,, ,,, ,,, ,....

Toasting Notes:

. Lower oven may not be operated while upper oven

is toasting. If the lower oven is operating when the Toast pad is pressed, a beep will sound.

. Toasting is based on time not temperature. . For more even browning results, preheat the oven 3-4

minutes.

/_,' ,;',_ I_ ,,,,,',,",>

'/4 ,_ 7/ i'_> _ 'II',

To cancel Keep Warm:

1. Press the CANCEL pad.

2. Remove food from the oven.

Keep Warm Notes:

. For optimal food quality, ovencooked foods should be kept

warm for no longer than 1 to 2 hours.

. To keep foods from drying, cover loosely with foil or a lid. . To warm dinner rolls:

cover rolls loosely with foil and place in oven. press Keep Warm and More+ pads to set 170°F.

- warm for 12-15 minutes.

. To warm plates:

place 2 stacks of up to four plates each in the oven. press Keep Warm and More+ pads to set 170°F.

- warm for five minutes, turn offthe oven and leave plates in the oven for 15 minutes more.

use only oven-safe plates, check with the manufacturer. do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing or breakage.

Toasting times will be shorter when the oven is hot or when repeated toasting functions are done.

For optimal results when toasting/4-5 pieces of bread or other similar items, follow illustration above.

Toasting Chart

Sliced White Bread Waffles (frozen) Toaster Pastry (unfrozen) Toaster Pastry (frozen)

Tortillas(flour) ToasterBreaks** or

Hot Pockets** Bagels

English Muffins Cheese Sandwich

* Toasting times are approximate and should be used as a

guide only.

** Brand names are registered trademarks of the respective

manufacturers.

21/2 - 3 min.

4 -5 min.

41/2 - 5 min. 31/2 - 4 min.

31/2 - 41/2 min

Broiling

To set Broil:

1. Press the Broil pad for desired oven. "Broil" and "SEt" flash in the display.

Press the More+ or Less- pad once to set HI broil. Press the More+ or Less- pad twice to set LO broil.

HI or LO will be displayed. Select HI broil (550° F) for normal broiling. Select

LO broil (450° F)for low-temperature broiling of longer cooking foods such as poultry.

3. After four seconds, the oven will start.

, "Broil" and HI or LO will remain lit.

For optimum browning, preheat broil element for 3-4 minutes before adding food.

Placefood in the oven. Leave oven door open about four inches (the first stop).

Most meat should be turned once about halfway through cooking.

7. When food is cooked, press the CANCEL pad. /f--_ Remove food and broiler pan from the oven.

The time of day will reappear in the display.

Broil

Broil Notes:

, For best results when broiling, use a two-piece broiler

pan.

, HI broil is used for most broiling. Use LO broil when

broiling longer cooking foods to allow them to cook to well done stage without excessive browning.

, Broil times may be longer when the LO broil temperature

is selected. Never cover broiler pan insertwith aluminum foil. This

prevents fat from draining to the pan below. Expect broil times to increase and browning to be slightly

lighter if appliance is installedon a 208-volt circuit. If more than 30 seconds elapse between pressing the

Broil pad and the More+ or Less- pad, the oven will not be set and the display will return to the previous display.

Most foods should be turned halfway through broiling time.

Broiling Chart = Broil times are based on a 4 minute preheat.

Beef Steak, 1" thick,

4 oz. Hamburgers, 3/4" thick (up to 12) 4 oz. Hamburgers, 3/4" thick (up to 6)

Chicken

Bone-in, skin-on breast Pieces

Fish

Filets Steaks, 1" thick

Pork

Chops, 1" thick on rack 4 HI 18- 24 (well) 22 - 27 (well)

When broiling fish, spray broil pan insert with cooking oil. Do not turn fish filets.

** Broiling times are approximate and may vary depending on the thickness of the food. Turn meat halfway through cooking times.

on rack on rack on rack

on rack

on rack on rack

3or4

4 4

HI HI HI

LO LO

8- 11 (medium)

15 - 20 (well) 12 - 16 (well)

25 - 36 (well)

8- 12 (flaky)

lo - 14(flaky)

15 - 19 (medium)

15- 19 (well) 15- 19 (well)

28 - 39 (well)

8- 13 (flaky)

10 - 16 (flaky)

Automatic Shut-Off/Sabbath

Mode

The ovens will automatically turn off after 12 hours if you accidentally leavethem on. The oven MUST be set for a

bake operation before setting the Automatic Shut=off/ Sabbath Mode.

To cancel the 12=hour shut=off and run the ovens continuously for 72 hours:

1. Set the oven to bake (see page 10).

2. Press and hold the Clock pad for five seconds. , "SAbbAth"* will be displayed and flash for five seconds.

, "SAbbAth" will then bedisplayed continuously until

turned off or until the 72-hour time limit is reached.

, "Bake" and the oven temperature will also be displayed

if a bake setting is in use while the oven is in Sabbath Mode.

All other functions EXCEPTBAKE (Timer, Keep Warm,

Clean, etc.) are locked out during the Sabbath Mode.

To cancel Bake when in Sabbath Mode:

Press the CANCEL pad.

, "Bake" and the oven temperature will turn

off in the display. "SabbAth" appears in the display.

"Time" no longer appears in the display.

To cancel the Sabbath Mode:

Sabbath Mode Notes:

, Sabbath Mode can be turned on only when the ovens

are on. Sabbath Mode cannot be turned on if the touchpads are

locked out or when the doors are locked. If the oven light is desired while in Sabbath Mode, it

must be turned on before the Sabbath Mode is started.

When the Sabbath Mode is started, no preheat beep will

sound.

All prompts, messages and beeps are deactivated when

Sabbath Mode is active.

The automatic door lock does not operate during the

Sabbath Mode.

, Pressing CANCEL pad will cancel a bake cycle, however

the control will stay in the Sabbath Mode. If power fails, the ovens will power up in Sabbath Mode

with 72 hours remaining and no cycle active.

1. Pressthe Clock pad for five seconds. , "SAbbAth" will flash for 5 seconds.

, The time of day will return to the display. OR

2. After 72 hours, the Sabbath Mode will end. , "SAbbAth" will flash for 5 seconds.

, The time of day will return to the display.

* Note: "SAbbAth" appears in the display on two lines: SAb.

bAth

Adjusting the Oven Temperature

Oven temperatures are carefully tested for accuracy at the factory. It is normal to notice some baking or browning

differences between a new oven and an old one. As ranges get older, the oven temperature can shift.

You may adjust the oven temperature if you think the oven is not baking or browning correctly. To decide how much to

change the temperature, set the temperature 25° higher or lower than your recipe recommends, then bake. The results of the "test" should give you an idea of how much to adjust

the temperature.

To adjust the oven temperature:

1. Pressthe appropriate Bake pad.

2. Enter 550° by pressing the More+ pad.

3. Press and hold the Bake pad for several seconds or until "0°'' and "AdJ" (which

signifies 'adjust':} appear in the display. If the oven temperature was previously adjusted, the

change will be displayed. For example, if the oven tem- perature was reduced by 15°the display will show "-15°".

4. Pressthe More+ or Less- pad to adjust the temperature. Eachtime a pad is pressed, the temperature changes by

5°. The oven temperature can be increased or decreased by 5° to 35°.

5. The time of day will automatically reappear in the display

You do not need to readjust the oven temperature if there

is a power failure or interruption. Broiling and cleaning

temperatures cannot be adjusted.

Bake

Oven Vent

When the oven is in use the area near the vent may become

hot enough to cause burns. Never block the vent opening.

The oven vent is located below the backguard vent

shield on your range.

When high moisture foods are cooked in the upper oven,

steam may be visible coming from the oven vent. This is normal.

Do not place plastics near the

vent opening as

heat from the vent

could distort or

TION

melt the plastic.

Oven Racks

All racks are designed with a lock-stop edge.

Upper oven

, Is equipped with one rack and rack

position.

, When pulling the upper oven rack out to

remove or check food, grasp the top edge of the rack.

Lower oven

Oven Lights

The oven lights automatically come on when an

oven door is opened. When the doors are closed, press the appropriate Oven Light pad to turn the

oven lights on and off. A beep will sound every time

the Oven Light pad is pressed.

Oven Bottom

Protect oven bottom against spillovers, especially acidic or sugary spills, as they may discolor the porcelain enamel. Use

the correct pan size to avoid spillovers and boilovers. Do not

place utensils or aluminum foil directly on the oven bottom.

Is equipped with one RollerGlideTM rack and one flat rack

(select models) or two flat racks.

To remove oven racks:

Pull rack straight out until it stops at the lock-stop position; lift up on the front of the rack and pull out.

For RollerGlideTM rack, pull both the rack glide and rack base out together.

To replace oven racks:

Place rack on the rack support in the oven; tilt the front end up

slightly; slide rack back until it clears the lock-stop position; lower front and slide back into the oven.

Baking and Roasting with the RollerGuide TM Rack (selectmodels)

Baking

, When baking on two racks, use the RollerGlide TM rack in

the lower rack position, and the flat rack in the upper rack position.

Roasting

, When roasting large cuts of meat and poultry, use the

RollerGlideTM rack for ease of movement.

cont.

Rack Positions (lower oven]

--5

--4

--3

--2

--1

RACK 5: Use for toasting bread or broiling very thin foods and two-rack baking.

RACK 4: Use for two-rack baking and for broiling. RACK 3: Use for most baked goods on a cookie sheet or jelly

roll pan, layer cakes, fruit pies, or frozen convenience foods and for broiling.

RACK 2: Use for roasting small cuts of meat, casseroles, baking loaves of bread, bundt cakes or custard pies and two-

rack baking. RACK 1: Use for roasting large cuts of meat and poultry,

frozen pies, dessert souffles or angel food cake and two-rack baking.

MULTIPLE RACK COOKING: Two rack: Use rack positions 2 and 4, 1 and 4, or 2 and 5.

Baking Layer Cakes on Two Racks

For best results when baking cakes and cookies on two racks, use racks 2 and 4.

Place the cakes on the rack as shown.

Half Rack Accessory

([Loweroven only_)

A half rack, to increaseoven capacity, is available as an acces-

sory. It fits in the left, upper portion of the lower oven and provides

space for a vegetable dish when a large roaster ison the lower rack.

Contact your Maytag dealer for the "HALFRACK" Accessory Kit or call

1-877-232-6771 USA or 1-800-688-8408 Canada to order.

Self-Clean Oven

The self-clean cycle uses above-normal cooking temperatures to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers to prevent excessive smoke and flare-ups. Do not allow a

heavy build-up of soil to accumulate in the oven. During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self=Cleaning

1. Turn off the oven light before cleaning. The light may burn out during the clean cycle.

Remove broiler pan, all pans, and oven racks from the oven. The oven racks will discolor and may not slide easily

after a self-clean cycle if they are not removed.

Clean oven frame, door frame, area

outside of gasket, and around the opening in the door gasket with a

nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not clean these areas. They should be

cleaned to prevent soil from baking on during the clean cycle. (The gasket isthe seal around the oven door and

window.)

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket is designed to seal in heat

during the clean cycle.

5. Wipe up excess grease or spillovers from the oven bottom.

This prevents excessive smoking, flare-ups or flaming

during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet potatoes, tomato, or milk-based sauces. Porcelain enamel

isacid-resistant, not acid-proof. The porcelain finish may discolor ifacidic spills are not wiped up before a self-

clean cycle.

Notes:

* Oven temperature must be below 400° F to program a

clean cycle. * Only one oven can be cleaned at a time. * Both oven doors lock when either oven is being

cleaned.

set Self=Clean:

Close the oven door.

Press the Clean pad. * "Clean" and "SEt" flash inthe display.

If the door is not closed within 25 seconds, the self- cleaning operation will be canceled and the display will return to the time of day.

Press the More+ or Less- pad.

"MEd" for medium amount of soil (3 hours) appears in the display.

If the door is not closed, "door" will appear in the display. After 45 seconds, three beeps will

sound, the self-cleaning operation will be canceled and the display will return to the time of day.

Press the More+ pad twice for heavy soil (4 hours).

"HVy" will be displayed. Press Less- pad twice for light soil (2 hours). * "LITE" will be displayed.

Choosing the soil level of the oven automatically programs the self-cleaning time. "Lock" flashes in the display.

After four seconds, the oven will start cleaning.

* The cleaning time will start counting down in the display. * "Lock" will appear in the display and will flash until the

doors are locked. "Lock" will then remain lit. * "Clean" will remain lit in the display.

To Delay a Self=Clean Cycle:

1. Press the Delay pad once for upper oven and twice for lower oven.

*"dLY" flashes. * "0:00" flashes in the display.

Press the More+ or Less- pad to set the amount of time you want to delay the cycle.

Delay time can be set from ten minutes (10:00) to 11 hours, 59 minutes (11:59).

cont.

*Brand names for cleaning products are registered trademarks ofthe respective manufacturers.

Cleanln

Pressthe apropriate Clean pad while "dLY" is flashing.

, "Clean" and "Set" will flash. If the door is not closed within 25 seconds, the self-

cleaning operation will be canceled and the display will return to the time of day.

4. Pressthe More+ or Less- pad. , "MEd" for medium amount of soil (3 hours)

is displayed.

If the door is not closed, "door" will appear in

the display. After 45 seconds, three beeps will sound, the

self-cleaning operation will be canceled and the display

will return to the time of day.

5. Pressthe More+ pad twice for heavy soil (4 hours). , "HVy" will be displayed.

Pressthe Less- pad twice for light soil (2 hours). , "LITE" will be displayed. Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, "Clean", "dLY" and "Lock" will appear in the display to show that the oven is set for a delayed clean operation. The delay time is displayed and will begin

to count down.

( Clean

During the Self=Clean Cycle

When "Lock" shows in the display, both oven doors are locked. To prevent damage to the doors, do not force the

doors open when "Lock" is displayed.

Smoke and Smells

You may see some smoke and smell an odor the first few times the oven is cleaned. This is normal and will lessen in

time. Smoke may also occur if the oven is heavily soiled or if a

broiler pan was left in the oven.

Sounds

As the oven heats, you may hear sounds of metal parts expanding and contracting. This is normal and will not

damage the oven.

After Self=Cleaning

About one hour after the end of the self-clean cycle, "Lock" will turn off. The doors can then be opened.

Some soil may leave a light gray, powdery ash. Remove it with a damp cloth. If soil remains after wiping, that means

the clean cycle was not long enough. The soil will be re- moved during the next clean cycle.

If oven racks were left in the oven and do not slide smoothly after a clean cycle, wipe racks and rack supports

with a small amount of vegetable oil to make them easier to move.

When the Self=Clean cycle starts:

"dLY" will turn off. "Clean", "Hours", "Lock" and the clean time will appear

in the display.

To cancel the Self=Clean cycle:

Press the CANCEL pad. (CANCEL)

, All words disappear from the display. , All functions are canceled.

The time of day appears in the display.

Fine lines may appear in the porcelain because it went through heating and cooling. This is normal and will not

affect performance.

A white discoloration may appear after cleaning if acidic or sugary foods were not wiped up before the self=clean

cycle. This discoloration is normal and will not affect perfor-

mance.

Self=Clean Notes:

, if the oven door is left open, "door" will appear in the

display until the door is closed.

, If more than five seconds elapse between pressing the

Clean pad and the More+ or Less- pad, the program will automatically return to the previous display.

The oven door will be damaged if the oven door is forced to open when "Lock" is still displayed.

Cleaning Procedures

* Brand names are registered trademarks of the

respective manufacturers.

** To order call 1-877-232-6771 USAand

1-800-688-8408 Canada.

Backguard and

Cooktop -

Porcelain Enamel

Broiler Pan and Insert

Clock and Control Pad

Area

Control Knobs

Cooktop - Glass=Ceramic

Porcelain enamel is glass fused on metal and may crack or chip with misuse. It is acid resistant, not acid proof. All spillovers, especially acidic or sugary spillovers, should bewiped up immediatelywith a dry cloth.

* When cool, wash with soapy water, rinse and dry. * Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.

* Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.

Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.

* Place soapy cloth over insert and pan; let soak to loosen soil. * Wash in warm soapy water. Use scouring pad to remove stubborn soil.

* Broiler pan and insert can be cleaned in dishwasher. * To activate "Control Lock" for cleaning, see page 9.

* Wipe with a damp cloth and dry. Do not use abrasive cleaning agents as they may scratch the surface. * Glass cleaners may be used if sprayed on a cloth first. DO NOTspray directly on centre/pad and

display area.

* Remove knobs in the OFF position by pulling forward. * Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish. * Turn on each element to be sure the knobs have been correctly replaced.

Never use oven cleaners, chlorine bleach, ammonia or glass cleaners with ammonia. NOTE: Call an authorized servicer if the glass=ceramic top should crack, break or if metal or aluminum foil

should melt on the cooktop. * Allow the cooktop to cool before cleaning.

* General - Cleancooktop after each use, orwhen needed, with a damp paper towel and Cooktop Cleaning

Creme* (Part No. 20000001)**. Then, buff with a clean dry cloth.

NOTE: Permanent stainswill developff soil b allowed to cook on byrepeatedly using the cooktop whensoiled.

* Heavy Soils or Metal Marks - Dampen a "scratchless" or "never scratch" scrubber sponge. Apply

Cooktop Cleaning Creme* (Part No. 20000001)** and scrub to remove as much soil as possible. Apply a

thin layer of the creme over the soil, cover with a damp paper towel and let stand 30 to 45 minutes (2-3

hours for very heavy soil). Keep moist by covering the paper towel with plastic wrap. Scrub again, then buff with a clean dry cloth.

NOTE: Onlyuse a CLEAN,DAMP "scratchless"pad that is safefor non-stick cookware. Thepattern andglass

will be damaged ff the pad b not damp, ff the pad b soiled, or ff another type of pad b used.

* Burned=on or Crusty Soils - Scrub with a "scratchless" or "never scratch" scouring pad and Cooktop

Cleaning Creme*.

NOTE: Hold a razor blade scraper at 30°angle and scrape any remaining soil Then,clean as de- _ scribed above. Donot usethe razorblade for dailycleaning asit may wearthe pattern on theglass. __/ "

Melted Sugar or Plastic - Immed=atelyturn element to LOW and scrape sugar or ,,_ ,J ':",,," plastic from hot surface to a cool area. Then turn element OFFand allow to cool. Clean , i:,,

• • • , F,_ '}i

residue with razor blade scraper and Cooktop Cleamng Creme. _ i [Ji

! _l ,,,,i i iii,i

", }}i !

Oven Windows and Doors =

Glass

* Avoid using excessive amounts of water which may seep under or behind glass causing staining. * Wash with soap and water. Rinsewith clearwater and dry. Glasscleaner can be used if sprayed on a cloth

first.

* Do not useabrasive materials such as scouring pads, steelwool or powdered cleaners astheywill scratch

glass.

Oven Interior . Follow instructionson pages 18-19 to set a self-clean cycle.

Oven Racks

StainJess Steel

(select models:)

Door Handles,

Side Panels -

Painted Enamel

Clean with soapy water.

Remove stubborn soil with cleansing powder or soap-filled scouring pad. Rinse and dry.

Rackswill permanently discolorandmay not slide smoothly if left inthe oven during aself-clean operation. If this occurs, wipe the rack edge and rack support with a small amount of vegetable oil to restore ease

of movement, then wipe off excess oil.

* DO NOT USEANY CLEANING PRODUCT CONTAINING CHLORINE BLEACH. * DO NOT USEABRASIVE OR ORANGE CLEANERS. * ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.

* Daily Cleaning/Light Soil --Wipe with one ofthe following - soapywater, white vinegar/water solution,

Formula 409 Glass and Surface Cleaner* or a similar glass cleaner - using a sponge or soft cloth. Rinse and dry. To polish and help prevent fingerprints, follow with Stainless Steel Magic Spray (Part No.

20000008:)**.

* Moderate/Heavy Soil == Wipe with one of the following -Bon Ami, Smart Cleanser, or Soft Scrub* -

using a damp sponge or soft cloth. Rinse and dry. Stubborn soils may be removed with a damp multi- purpose Scotch-Brite* pad; rub evenlywith the grain. Rinseand dry.To restore luster and remove streaks,

follow with Stainless Steel Magic Spray*.

* Discoloration == Using a damp sponge or soft cloth, wipe with Cameo Stainless Steel Cleaner*. Rinse

immediatelyand dry. To remove streaks and restore luster, follow with Stainless Steel Magic Spray*.

When cool, wash with warm soapy water, rinse and dry. Never wipe a warm or hot surface with a damp

cloth as this may damage the surface and may cause a steam burn. Forstubborn soil, use mildly abrasive cleaning agents such as baking soda paste or BonAmi.* Do not use abrasive,caustic or harsh cleaning agents such as steel wool pads or oven cleaners. These products will scratch or permanently damage the surface.

NOTE: Use a dry towel or cloth to wipe up spills, especially acidic or sugary spills. Surface may discolor or dull ifsoil isnot immediately removed. Thisisespecially important for white surfaces.

* Brand names for cleaning products are registered trademarks of the respective manufacturers. ** To order direct, call 1-877-232-6771 USA and 1-800-688-8408 Canada.

Maintenance

Oven Doors

• Do not place excessive weight on or stand on open oven

doors. This could cause the range to tip over, break the door, or injure the user.

Do not attempt to open or close doors or operate oven until doors are properly replaced.

, Never place fingers between hinge and front oven frame.

Hinge arms are spring mounted. If accidentally hit, the hinge will slam shut against oven frame and could injure

your fingers.

Both the upper and lower oven doors are removable.

To remove:

1. When cool, open the oven door to the bronl stop posnt_on (opened about four Hlches].

2. Grasp door at each snde. Do not use the door handle to Inft door.

3. Lift Lipevenly until door clears hinge arms.

Oven Windows

To protect the oven door window:

1. Do not use abraswe cleaning agents such as steel wool scounng pads or powdered cleansers as they may scratch

the glass.

2. Do not hutthe glass w_th pots, pans, furnnture, toys, or other objects.

3. Do not close the oven door until the oven racks are _rl

place.

Scratching, hutting,jarnng or stressHlg the glass may weaken

_tsstructure causnngan H_creasednsk of breakage at a later

date.

Upper and Lower Oven Lights

. Disconnect power to oven before replacing light bulb.

• Allow oven to cool before replacing light bulb.

• Make sure bulb cover and bulb are cool before touching.

To replace:

1. Grasp door at each snde.

2. Alngn slots _nthe door w_th the hnngearms on the range.

3. Slndethe door down onto the h_ngearms untd the door _s completely seated on the hnnges.Push down on the top

corners of the door to completely seat door on hinges. Door should not appear crooked.

when _t_sclosed. This _snormal and w_lldecrease w_th use.

Note: The oven door on a new range may feel "spongy"

Oven Bottom

Protect oven bottom against spdlovers, especially acidic or sugary sp_lls,as they may d_scolorthe porcelain enamel. Use

the correct pan snzeto avondspnlloversand bo=lovers.Do not place aluminum foil directly on the oven bottom.

Toassure the proper replacement bulb _sused, order bulb from Maytag. Call 1-877-232-6771 USA and 1-800-688-8408 Canada,

ask for part number 74009925 - halogen bulb.

To replace upper oven light bulbs:

Disconnect power to the range.

When oven iscool, use fingertips to grasp edge of bulb cover.

Pull out and remove.

Carefully remove old bulb by pullnngstraight out of ceramic

base.

To avoid damaging or decreasHlg the hfe of the new bulb, do

not touch the bulb w_th bare hands or fingers. Hold with a

cloth or paper towel. Push new bulb prongs straight into small holes of ceramic base.

5. Replace bulb cover by snappnng_nto place.

6. Reconnect power to range. Reset clock.

Maintenance

Leveling Legs

Be sure the anti=tip bracket secures one of the rear leveling legs to the floor. This bracket prevents the range

from accidentally tipping.

Be sure the range should be leveled when installed. Ifthe range _snot level, turn the

levehng legs, located at each corner of the range, until range _slevel. /_,,

-, j

'-i _-£

, : 'r, _ ANTI-TIPBRACKET

LEVELING LEG

Convenience

Outlet

(Canadian models only:)

The convenience outlet is located on the lower left side of the

backguard, Be sure applnance cords do not rest on or near the

surface element, If the surface element _sturned on, the cord and

outlet w_llbe damaged,

The convenience outlet c_rcunt breaker may trip _fthe small

apphance plugged into ,t exceeds

10 amps, To reset the cHcunt

breaker, press the sw_tch located on the lower edge of the backguard,

.... ,,,,,

' I'1 , I,

° =

.d.....

CIRCUIT BREAKER

Troublesbootin9

For most concerns, try these first.

Part or all of appliance does not work.

Check

if oven controls have been properly set.

Check

to be sure plug is securely inserted into receptacle.

Check

or re-set circuit breaker. Check or replace fuse.

Check

power supply.

Check

if surface and/or oven controls have been properly set. See pages 4 & 10.

Check

if oven door is unlocked after self-clean cycle. See page 19.

Check

if oven is set for a delayed cook or clean program. See pages 11 & 18.

Check

if Control Lock is activated. See page 9.

Check

if control is in Sabbath Mode. See page 14.

Oven light and/or clock

does not function.

Clock, indicator words, and/or lights operate but oven does

not heat.

Baking results are not as expected or differ from

previous oven.

Food is not broiling properly or

smokes excessively.

* The light bulb is loose or defective. * The oven light does not work during self-cleaning process.

* Oven may be in Sabbath Mode. See page 14.

* Oven may be set for aCook & Hold or Delay function. * The Control Lock may have been set.See page 9.

Make sure the oven vent has not been blocked. See page 16 for location.

Check to make sure range is level.

Temperatures often vary between a new oven and an old one.As ovens age,the oven temperature often "drifts" and may become hotter or cooler. See page 15 for

instructions on adjusting the oven temperature. NOTE: It is not recommended to adjust the temperature if only one or two recipes are in question.

* Check oven rack positions. Food may be too close to element. * Broil element was not preheated.

* Aluminum foil was incorrectly used. Never line the broiler insertwith foil. * Oven doorwas closed during broiling. Leavethe door open to the first stop position

(about 4 inches_). * Trim excess fat from meat before broiling. * A soiled broiler pan was used.

* Voltage in house may be low.

Oven wiil not self=clean.

Oven did not clean properly.

* Check to make sure the cycle is not set for a delayed start. See page 18. * Check if door isclosed.

* Check if control is inSabbath Mode. See page 14. * Oven may be over 400° F. Oven temperature must be below 400° Fto program a

clean cycle.

* Longer cleaning time may be needed. * Excessive spillovers, especially sugary and/or acidic foods, were not removed prior

to the self-clean cycle.

cont.

Troublesbootln9

Oven door will not unlock after self=clean cycle.

Smoothtop surface shows

wear.

Moisture collects on oven window or steam comes from

oveu veut.

Oven interior is still hot. Allow about one hour for the oven to cool after the completion of a self-clean cycle. The door can be opened when "Lock" is not

displayed. The control and door may be locked. See page 9.

1. Tiny scratches or abrasions.

, Make sure cooktop and pan bottom are clean. Do not slide glass or metal pans

across top. Make sure pan bottom is not rough. Use the recommended cleaning agents. See page 20.

2. Metal marks. , Do not slide metal pans across top. When cool, clean with Cooktop

Cleaning Creme. See page 20.

3. Brown streaks and specks. , Remove spills promptly. Never wipe with a soiled cloth or sponge. Make sure

cooktop and pan bottom are clean.

4. Areas with a metallic sheen. , Mineral deposits from water and food. Use recommended cleaning agents.

See page 20.

5. Pitting or flaking. , Remove sugary boilovers promptly. See page 20.

This is normal when cooking foods high in moisture.

, Excessive moisture was used when cleaning the window.

There is a strong odor or light smoke when oven is turned on.

Fault Codes

Noises may be heard.

There are no beeps and

no display.

• This is normal for a new range and will disappear after a few uses. Initiating a clean cycle will "burn off" the odors more quickly.

Turning on a ventilation fan will help remove the smoke and/or odor. Excessivefood soils on the oven bottom. Use a self-clean cycle.

"Bake" or "Lock" may flash rapidly in the display to alert you if there is an error or a problem. If "Bake" or "Lock" appear in the display, press CANCEL pad.

If "Bake" or "Lock" continue to flash, disconnect power to the appliance. Wait a few minutes, and then reconnect power. If the flashing still continues,

disconnect power to the appliance and call an authorized servicer. If the oven is heavily soiled, excessive flareups may result in a fault code during

cleaning. Pressthe CANCEL pad and allow the oven to cool completely, wipe out excess soil, then reset the clean cycle. If the fault code reappears, contact an

authorized servicer.

The oven makes several low levelnoises. You may hear the oven relays asthey go on and off. This is normal.

As the oven heats and cools, you may hear sounds of metal parts expanding and contracting. This is normal and will not damage your appliance.

Oven may be in Sabbath Mode. See page 14.

+ 58 hidden pages

Maytag MER6755ACS26, MER6755ACB24, MER6755ABW25, MER6755AAS26, MER6755AAB24 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual