Maytag MGDC400BW, MGDC300BW, MEDC400BW, MEDC300BW Owner's Manual
SÉCHEUSE
ELECTRIC OR GAS DRYER
USE AND CARE GUIDE
ÉLECTRIQUE OU À GAZ GUIDE
D’UTILISATION
ET D’ENTRETIEN
Para una versión de estas instrucciones en español, visite www.maytag.com
Table of Contents Table des matières
DRYER SAFETY ............................................................2
CHECK YOUR VENT SYSTEM
FOR GOOD AIR FLOW .................................................4
USE SENSOR DRY/AUTOMATIC DRY CYCLES FOR
BETTER FABRIC CARE AND ENERGY SAVINGS ......4
CONTROL PANEL & FEATURES .................................. 5
CYCLE GUIDE ............................................................... 6
USING YOUR DRYER ...................................................7
DRYER CARE ................................................................9
TROUBLESHOOTING ................................................. 11
WARRANTY .................................................................13
ASSISTANCE OR SERVICE .................... BACK COVER
SÉCURITÉ DE LA SÉCHEUSE ...................................14
VÉRIFICATION D’UNE CIRCULATION D’AIR
ADÉQUATE POUR LE SYSTÈME D’ÉVACUATION .. 16
UTILISATION DES PROGRAMMES DE SÉCHAGE
PAR DÉTECTION/PROGRAMMES AUTOMATIQUES
POUR UN MEILLEUR SOIN DU TISSU ET DAVANTAGE
D’ÉCONOMIES D’ÉNERGIE ....................................... 16
TABLEAU DE COMMANDE
ET CARACTÉRISTIQUES ...........................................17
GUIDE DE PROGRAMMES ........................................18
UTILISATION DE LA SÉCHEUSE ............................... 19
ENTRETIEN DE LA SÉCHEUSE ................................. 21
DÉPANNAGE. ..............................................................24
GARANTIE. .................................................................. 27
ASSISTANCE OU SERVICE. . COUVERTURE ARRIÈRE
W10562354B
W10562355B - SP
DRYER SAFETY
2
3
CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW
Maintain good air ow by:
■ Cleaning your lint screen before each load.
■ Replace plastic or foil vent material with 4" (102 mm)
diameter heavy, rigid vent material.
■ Use the shortest length of vent possible.
■ Use no more than four 90° elbows in a vent system;
each bend and curve reduces air ow.
Good Better
Good air ow
Along with heat, dryers require good air ow to efciently
dry laundry. Proper venting will reduce your drying times
and improve your energy savings. See “Installation
Instructions.”
The venting system attached to the dryer plays a big role in
good air ow.
Service calls caused by improper venting are not covered
by the warranty and will be paid by the customer, regardless
of who installed the dryer.
■ Remove lint and debris from the exhaust hood.
■ Remove lint from the entire length of the vent system at
least every 2 years. When cleaning is complete, be sure
to follow the “Installation Instructions” supplied with your
dryer for nal product check.
■ Clear away items from the front of the dryer.
USE SENSOR DRY/AUTOMATIC DRY CYCLES FOR BETTER FABRIC CARE
AND ENERGY SAVINGS
Use the Sensor Dry/Automatic Dry cycles to provide the most energy savings and enhanced fabric care from the dryer. During
Sensor Dry/Automatic Dry cycles, drying air temperature or moisture level is sensed in the load. This sensing occurs throughout
the drying cycle and the dryer shuts off when the load reaches the selected dryness. The Energy Preferred cycle will provide
optimal energy savings.
With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to over-drying.
Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.
4
CONTROL PANEL & FEATURES
42 31
Not all features and options are available on all models.
1
TEMPERATURE/FABRIC
Select a drying temperature based on the fabrics in your
load. If you are unsure of the temperature to select for a
load, select the lower setting rather than the higher setting.
2
CYCLE KNOB
Use Cycle Knob to select available cycles on your dryer.
Turn the knob to select a cycle for your laundry load. See
“Cycle Guide” for detailed descriptions of cycles.
TIMED DRY
Will run the dryer for the specied time on the control.
On models with a selectable temperature knob, you
may choose a setting based on the fabrics in your load.
On some models, temperature is included in the cycle
selections. Drying time and temperature will depend on
your dryer model.
SENSOR DRY/AUTOMATIC DRY
Senses moisture in the load or air temperature and shuts
off when the load reaches the selected dryness level.
Gives the best drying in the shortest time. Drying time
will vary based on fabric type, load size, and temperature
setting.
2
Appearance may vary.
WRINKLE CONTROL option (on some models)
3
When you are unable to remove a load of clothes from the
dryer as soon as it stops, wrinkles can form. The WRINKLE
CONTROL option periodically tumbles, rearranges, and
uffs the load to help keep wrinkles from forming.
■ Get up to 90 minutes of heat-free, periodic tumbling at
4
PUSH TO START/END OF CYCLE SIGNAL
The End of Cycle Signal produces an audible sound when
the drying cycle is nished. Promptly removing clothes at
the end of the cycle reduces wrinkling.
Turn the END OF CYCLE SIGNAL knob to select the desired
setting (On or Off). Press the PUSH TO START knob to start
the dryer.
1
4
WRINKLE CONTROL Feature (on some models)
The WRINKLE CONTROL feature will run after your
drying cycle is complete. It periodically starts and stops
the dryer, tumbling the load without heat to help avoid
wrinkling.
On some models, WRINKLE CONTROL automatically
starts at the end of the cycle. Opening the door will stop
this feature.
NOTE: A signal will sound periodically when the
WRINKLE CONTROL setting is selected, but only if the
End of Cycle signal is also selected.
the end of a cycle. Turn the WRINKLE CONTROL knob
to select OFF or 90 min. at any time before the cycle has
ended.
5
CYCLE GUIDE — SENSOR DRY/AUTOMATIC DRY CYCLES
SENSOR DRY/AUTOMATIC DRY - Senses moisture in the load or air temperature and shuts off when the load reaches the selected
dryness level. Choose ENERGY PREFERRED cycle for optimal energy savings.
Not all cycles and settings are available on all models. Settings and options shown in bold are default settings for that cycle.
Items to dry:
Dryness Level:
Temperature
Available Options:
Cycle Details:
Fabric:
Jeans, heavy work
clothes, towels
Work clothes, medium
weight fabrics, sheets
Casual, shirts, pants,
lightweight items,
synthetics, delicates,
athletic wear
NOTE: If loads do not seem as dry as you would like, select More Dry next time you dry a similar load. If loads seem drier than you
like, select Less Dry next time you dry a similar load.
More Dry
Energy Preferred
Less Dry
More Dry
Energy Preferred
Less Dry
More Dry
Energy Preferred
Less Dry
High
Medium or
Low
Low
End of Cycle Signal
Wrinkle Control
End of Cycle Signal
Wrinkle Control
End of Cycle Signal
Wrinkle Control
Automatic cycles give the best drying
in the shortest time. Drying time varies
based on fabric type, load size, and
dryness setting.
Select a drying temperature based on
the fabrics in your load. If you are unsure
of the temperature to select for a load,
select the lower setting rather than the
higher setting.
CYCLE GUIDE — TIMED DRY CYCLES
TIMED DRY - Will run the dryer for the specied time on the control.
Not all cycles and settings are available on all models.
Items to dry: Temperature:Cycle:
Available
Cycle Details:
Options:
Heavy or bulky
items
Any load Freshen Up Any End of Cycle Signal Use low to medium temperature to
Any load Damp Dry
Rubber, plastic, heat
sensitive fabrics
Heavy Dry Any End of Cycle Signal Completes drying if items are still damp.
smooth out wrinkles, such as those
found in clothes packed in a suitcase or
in items wrinkled from being left in the
dryer too long.
End of Cycle Signal
End of Cycle Signal
Dries items to a damp level or for items
that do not require an entire drying
cycle.
No heat drying.
Air Fluff
Any
Air Fluff
Setting the Drying Temperature
If your dryer has multiple heat settings:
A High temperature setting may be used for drying
heavyweight items such as towels and work clothes.
A Low to Medium temperature setting may be used for drying
medium-weight items such as sheets, blouses, dresses,
underwear, permanent press fabrics, and some knits.
Use the Air Fluff (no heat) setting for foam, rubber, plastic, or
heat-sensitive fabrics.
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions.
6
USING YOUR DRYER
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this dryer.
Before using your dryer, wipe the dryer drum with a damp cloth
to remove dust from storing and shipping.
1. Clean the lint screen
Clean the lint screen before each load. Pull the lint screen out
of its holder. Roll lint off the screen with your ngers. Do not
rinse or wash screen to remove lint. Push the lint screen rmly
back into place.
For additional cleaning information, see “Dryer Care”.
2. Load the dryer
Place laundry in the dryer. Close the door.
Do not tightly pack the dryer; clothes should be able to tumble
freely.
NOTE: Your model may have a different door than the one
shown. Some models have drop down doors.
7
3. Select the desired cycle
Select the desired cycle for your load. See the Cycle Guide
for more information about each cycle.
SENSOR DRY/AUTOMATIC DRY Cycles
You can select a different dryness level, depending on your
load, by turning the knob to dryness level.
Selecting More Dry, Energy Preferred, or Less Dry automatically
adjusts the dryness level of the fabrics at which the dryer will
shut off.
Sensor Dry/Automatic Dry cycles give the best drying in the
shortest time. Drying time varies based on fabric type, load
size, and dryness setting. Choose Energy Preferred for optimal
energy savings. Less Dry removes less moisture and is used for
loads you may want to put on a hanger to complete drying.
More Dry removes more load moisture. Energy Preferred is
used for a starting point for Sensor Dry/Automatic Dry cycles.
4. Set temperature (on some models)
5. Set Wrinkle Control (on some models)
Select Wrinkle Control by turning the knob to the desired
position.
Get up to 90 minutes of heat-free, periodic tumbling at the
end of a cycle. Turn the WRINKLE CONTROL knob to OFF
or 90 min. at any time before the cycle has ended.
NOTE: Not all options and settings are available with all
cycles.
6. Select End of Cycle Signal (if desired)
Turn the END OF CYCLE SIGNAL knob to select the desired
setting (On or Off). The End of Cycle Signal produces an
audible sound when the drying cycle is nished. Promptly
removing clothes at the end of the cycle reduces wrinkling.
Select temperature by turning the knob to the desired position
or select the Automatic Dry Cycle that has the temperature
included in the cycle selections. See “Setting the Drying
Temperature”.
NOTE: Not all options and settings are available with all cycles.
7. Press PUSH TO START to begin cycle
Push and hold the PUSH TO START knob to begin the cycle.
DRYING RACK ACCESSORY
To purchase a drying rack for your dryer, please refer to
“Assistance or Service” on the back cover of the manual or
contact the dealer from whom you purchased your dryer.
Part Number Accessory
3406839 Drying rack - ts 29" Super Capacity Plus
8
DRYER CARE
Cleaning the dryer location
Keep dryer area clear and free from items that would
block the air ow for proper dryer operation. This includes
clearing piles of laundry in front of the dryer.
Cleaning the dryer interior
To clean dryer drum
1. Apply a liquid, nonammable household cleaner to the
stained area of the drum and rub with a soft cloth until
stain is removed.
2. Wipe drum thoroughly with a damp cloth.
3. Tumble a load of clean cloths or towels to dry the drum.
NOTE: Garments that contain loose dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and
will not stain future loads of clothes. Dry these items inside
out to avoid drum staining.
Removing accumulated lint
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often,
depending on dryer usage. Cleaning should be done by
a qualied servicer.
From the Exhaust Vent
Lint should be removed every 2 years, or more often,
depending on dryer usage.
Cleaning the lint screen
Every load cleaning
The lint screen is located in the dryer. A screen blocked by
lint can increase drying time.
To clean:
1. Pull the lint screen out of its holder. Roll lint off the
screen with your ngers. Do not rinse or wash screen to
remove lint. Wet lint is hard to remove.
2. Push the lint screen rmly back into place.
IMPORTANT:
■
Do not run the dryer with the lint screen loose,
damaged, blocked, or missing. Doing so can cause
overheating and damage to both the dryer and fabrics.
■
If lint falls off the screen into the dryer during removal,
check the exhaust hood and remove the lint. See
“Venting Requirements.”
As needed cleaning
Laundry detergent and fabric softener residue can build
up on the lint screen. This buildup can cause longer drying
times for your clothes, or cause the dryer to stop before
your load is completely dry. The screen is probably clogged
if lint falls off while the screen is in the dryer.
Clean the lint screen with a nylon brush every 6 months,
or more frequently, if it becomes clogged due to a residue
buildup.
To wash:
1. Roll lint off the screen with your ngers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent.
Scrub lint screen with the brush to remove residue
buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel. Reinstall
screen in dryer.
9
Loading...