Maytag MDGT336AWW, MDGT236AWW, MDG5806AWW, MDG5806AWK, MDG508DAWW Owner’s Manual

...

M_ AG

MD-1

Important Safety

Instructions ................ 1-2

Using the Controls

Auto Dry Models .............. 3-4

Sensor Models ................ 5-6

Electronic Controls ............ 7-9

Operating Tips .............. 10

Accessories ................ 10

Care & Cleaning ............ 1 1

Form No. Y81904 A Part No. 2206672 www.maytag.com Litho U.S.A. _2006 Maytag Appliances Sales Co.

Troubleshooting ............. 14

Service & Warranty .......... 15

Guide d'utilisation

et d'entretien ............... 16

Guia de uso y cuidado ....... 32

ImportnntSnfet¥Instructions

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in this guide are not meant to cover all possible

conditions and situations that may occur. Common sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

ImportnntSnfet¥Instructions

1. Read all instructions before using the appliance.

2. To avoid the possibility of fire or explosion: a. Do not dry items that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode. Any

material on which you have used a cleaning solvent, or which is saturated with flammable

liquids or solids, should not be placed in the dryer, until all traces of these flammable liquids

or solids and their fumes have been removed. There are many highly flammable items used in

homes, such as: acetone, denatured alcohol, gasoline, kerosene, some liquid household

cleaners, some spot removers, turpentine, waxes and wax removers.

b. Items containing foam rubber (may be labeled

latex foam) or similarly textured rubber-like materials must not be dried on a heat setting.

Foam rubber materials when heated, can under certain circumstances produce fire by

spontaneous combustion.

3. Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is

necessary when the appliance is used near children and pets.

/4. Before the appliance is removed from service or

discarded, remove the door to the drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to the weather.

7. Do not tamper with controls.

8. Do not repair or replace any part of the appliance or attempt any servicing unless specifically

recommended in published user-repair instructions that you understand and have the skills to carry out.

9. Do not use fabric softeners or products to eliminate static unless recommended for dryer use

by the manufacturer of the fabric softener or product.

10.

Clean the lint screen before or after each load.

11.

Keep the area around the exhaust opening and surrounding areas free from lint accumulation, dust

and dirt.

12.

The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel.

13.

This appliance must be properly grounded. Never plug the appliance cord into a receptacle which is not grounded adequately and in accordance with

local and national codes. See installation instructions for grounding this appliance.

1/4. Do not sit on top of the clothes dryer.

Important Safety

Notice & Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65) requires the Governor of California to publish a list of substances

known to the State of California to cause cancer or reproductive harm, and requires businesses to warn

customers of potential exposures to such substances. Users of this appliance are hereby warned that the

burning of gas can result in low-level exposure to some of the listed substances, including benzene, formaldehyde, and soot, due primarily to the incomplete combustion of natural gas or liquid

petroleum (LP) fuels. Exhaust ducts should be kept free of obstructions and properly exhausted dryers will minimize exposure.

Note: Because of continuing product

improvements, Maytag reserves the right to change specifications without notice. For complete details, see the Installation Instructions packed with your product before selecting cabinetry, making cutouts or beginning installation.

SAVE THESE INSTRUCTIONS

UsingtheControls-AutoDryModels

Select Temperature

In order to select the correct temperature, turn the

Temperature control to one of four choices; Regular,

Medium (select models], Delicate or Air Fluff.

Regular Sturdy cottons or labels marked

Tumble Dry.

Medium For wrinkle-free/permanent press

(select models] synthetics, lightweight cottons

labeled Tumble Dry Medium.

Delicate For heat sensitive items labeled

Tumble Dry Low or Tumble Dry Medium.

Air Fluff Items which need freshening.

Load tumbles with room temperature air. Use the Time

Dry/Air Fluff cycle.

Select Options

Extended Tumble Cselect models)

Extended Tumble is provided to minimize wrinkles in

the Auto Dry Wrinkle Control cycle. This feature

provides an extra 60 minutes of unheated tumble action at the end of the cycle. Clothes can be removed

any time during this portion of the cycle.

The additional 60 minutes of unheated tumbling can

be canceled by turning the switch to Off.

End of Cycle Signal

When the cycle is complete, a signal will sound. On

select models, the End of Cycle Signal can be turned down or Off.

Remove load immediately to reduce wrinkling.

Temperature

Delicate

Air Fluff

r_eavy Duty / SuperSIze Capac [y / Quiet Sedes 10

Select Cycle

To select a cycle, rotate the control dial to the desired

setting. When using an Auto Dry cycle, the control dial should point between More Dry and Less Dry for most

loads. Loads of larger or bulkier size may require the More

Dry setting to completely dry the load. The Less Dry setting is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle.

Auto Dry Regular

The Auto Dry Regular cycle is designed to dry most

cottons and linens. At the end of the cycle, the clothes are cooled for approximately 10 minutes to reduce

wrinkling.

Auto Dry Wrinkle Control

The Auto Dry Wrinkle Control cycle is designed to dry wrinkle-free cottons, synthetic fabrics, double knits and

permanent press fabrics automatically. At the end of

the cycle, the clothes are cooled for approximately 25

minutes to reduce wrinkling. If the load is not removed from the dryer and Extended Tumble (select models]

has been selected, the cycle will advance to Extended

Tumble which provides additional unheated tumbling time. (See Step 2].

Signd

Auto Dry Normal Dry Off SC

Regular 4o

Time Dry

/ tocy4_ Air Fluff

.... /

Time Dry/Air Fluff

Less Dry Auto Dry

Mo_eD_ Wrinkle Co ntrol

off

40 70

50 6(

Push to Start

30 Extended Tumble

_'_off

lOG

80 Tumble

Cycles and options may vary by modeL

Extended

This cycle can be used to regulate the drying time. Use with Air Fluff, Delicate, Medium (select models) or

Regular temperature settings. For timed drying, turn the control dial until the pointer points to the proper time setting in the Time Dry/Air Fluff cycle.

require a longer drying time.

I Note: Using the Air Fluff temperature setting will

Damp Dry (select models)

Damp Dry is located on the Time Dry/Air Fluff section

of the dial. It is designed to partially dry items and can

be used with any temperature selection. Damp Dry will

provide 20 minutes of tumbling time, followed by

10 minutes of cool-down tumbling.

Push the Control Dial in

to Start

Push the control dial in to start the dryer. The dryer door must be closed for the dryer to start.

Note: The dial can be turned in either direction to

select a cycle. Once started, the dial will not advance at a specific rate during the Auto Dry

cycles. At first the dial may not advance at all. Toward the end of the cycle (when the load begins to dry), the dial will advance at a more regular rate

and much more quickly. This is normal operation.

UsingtheControls-SensorModels

Select Temperature

In order to select the correct temperature, turn the

Temperature control to one of four choices; Regular,

Medium, Low or Air Fluff.

Regular Sturdy cottons or labels marked

Tumble Dry.

Medium For wrinkle-free/permanent press

synthetics, lightweight cottons or items labeled Tumble Dry Medium.

Low For heat sensitive items labeled

Tumble Dry Low or Tumble Dry Medium.

Air Fluff Items which need freshening.

Load tumbles with room temperature air. Use the Time

Dry/Air Fluff cycle.

Select Options

Extended Tumble

Extended Tumble is provided to minimize wrinkles in

the Sensor Wrinkle Control cycle. This feature provides

an extra 60 minutes of unheated tumble action at the end of the cycle. Clothes can be removed any time

during this portion of the cycle.

The additional 60 minutes of unheated tumbling can

be canceled by turning the knob to Off or opening the door.

End of Cycle Chime

When the cycle is complete, a chime will sound. The

End of Cycle Chime can be turned off by turning the selector knob to Off.

Remove load immediately to reduce wrinkling.

Temperature

lOW M_dJU[/1

A[_"Fluff

Commercial Ouality Stainless Steel Tumbler t Sup

Chime

Select Cycle

To select a cycle, rotate the control dial to the desired

setting. When using a Sensor Wrinkle Control cycle, the control dial should point between More Dry and Less Dry for most loads.

Loads of larger or bulkier size may require the More Dry setting to completely dry the load. The Less Dry

setting is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle.

Sensor Regular

The Sensor Regular cycle is designed to dry most

cottons and linens. At the end of the cycle, the clothes are cooled to reduce wrinkling.

Sensor Wrinkle Control

The Sensor Wrinkle Control cycle is designed to dry wrinkle-free cottons, synthetic fabrics, double knits and

permanent press fabrics automatically. At the end of

the cycle, the clothes are cooled. If the load is not

removed from the dryer and Extended Tumble has

been selected, the cycle will advance to Extended Tumble which provides additional unheated tumbling time. (See Step 2).

Extended Tumble

rSize Capacity / Quiet SerBes100 / 12 Cvdes

........ /

Time Dry/Air Fluff

_essDr_ Sensor

Sensor Wrinkle Control

Re_.ular _

Off 3o Extended Tumble

Cool Down

Time Dry _° _'°

Air Fluff Pushtos_

Cycles and options may vary by model

This cycle can be used to regulate the drying time. Use with Air Fluff, Low, Medium or Regular temperature

settings. For timed drying, turn the control dial until the pointer points to the proper time setting in the Time

Dry/Air Fluff cycle.

require a longer drying time.

Note: Using the Air Fluff temperature setting will

Damp Dry (select models)

Damp Dry is located on the Time Dry/Air Fluff section of the dial. It is designed to partially dry items and can

be used with any temperature selection. Damp Dry will provide 20 minutes of tumbling time, followed by

10 minutes of cool-down tumbling.

Push the Control Dial in

to Start

Push the control dial in to start the dryer. The dryer door must be closed for the dryer to start.

Note: The dial can be turned in either direction to

select a cycle. Once started, the dial will not advance at a specific rate during the Sensor cycles.

At first the dial may not advance at all. Toward the

end of the cycle (when the load begins to dry), the dial will advance at a more regular rate and much more quickly. This is normal operation.

UsingtheControls-|lectronicControls

Select Temperature

Auto Temp [preferred setting) When Auto Temp is selected, the dryer will

automatically select the most appropriate drying

temperature based on the cycle and dryness settings

selected. If you prefer not to use Auto Temp. turn the

temperature selector knob to the desired setting.

Regular Sturdy cottons or labels marked

Tumble Dry.

Medium For wrinkle-free/permanent press

synthetics, lightweight cottons or items labeled Tumble Dry Medium.

Low For heat sensitive items labeled

Tumble Dry Low or Tumble Dry

Medium.

Air Fluff Items which need freshening.

Load tumbles with room

temperature air. Use the Time

Dry/Air Fluff cycle.

Temperature

Medium

Requ_ar

Auto TemD

Commercial Ouall_y Stainless Steel Tumbler ] SuoerS

Chime

Off On

Select Dryness Setting

To select the dryness level, turn the Dryness Settings

knob to the desired setting.

Most loads will use the Normal dry setting. Loads of

larger or bulkier size may require the More dry setting to completely dry the load.

Select Options [if desired)

End of Cycle Chime

When the cycle is complete, an audible chime will

sound. The chime will sound intermittently during

Wrinkle Prevent. On select models, the volume of the

chime can be adjusted. To turn the Chime off, turn the Chime selector knob to Off.

Wrinkle Prevent

Wrinkle Prevent provides approximately 95 minutes of

intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling. Set the Wrinkle Prevent switch On to activate this feature (select models). Some models automatically provide 30 minutes of

Wrinkle Prevent at the end of the Wrinkle Control cycle

only.

The Less dry setting is best suited for lightweight

fabrics or for leaving some moisture in the load at the

end of the cycle. Damp dry is designed to partially dry

items. Use for items that lay flat or hang to dry.

Select Cycle

To select a cycle, rotate the cycle selector dial to the

desired cycle. The indicator light by the cycle name will

illuminate. The dryer cycles are Sensor Dry cycles. Sensor Dry

automatically senses the moisture in the load and

shuts the dryer off when the selected dryness level

(Damp dry to More dry) is reached.

DrynessSettings sensorDry

Less Normal

_ Wdnk[e Control

_More

_eCapadty Ouiet Sedes 200 / 12 Cvdes

FabricSelection

Jeans

Regular

De[icates c

Dryinq Pause

"__LyQe Status Push to Stale - Push to Stoo

.... /

Refresh

6o Time Dry

50 Air Fluff

ii 20

Power

Off

Cycles and options may vary by model.

Wrinkle Prevent

Off

Refresh (select models)

The Refresh cycle is designed to release wrinkles from

items that are clean and dry but only slightly wrinkled, such as from a crowded closet or suitcase or from

sitting in the dryer too long after the cycle has ended. Refresh can be used with any temperature selection.

Note: If the dryer detects moisture in the load when Refresh is selected, the dryer will automatically switch

to the Wrinkle Control cycle which may extend the cyc e time.

Regular

The Regular cycle is designed to dry loads such as towels and underwear.

Jeans (select models) The Jeans cycle is designed to reduce wrinkling and

tangling in loads of jeans.

Wrinkle Control

The Wrinkle Control cycle is designed to dry wrinkle-

free cottons, synthetic fabrics, knits and permanent press fabrics automatically.

Select models will automatically advance into Wrinkle Prevent which provides an extra 30 minutes of

unheated tumble action at the end of the cycle.

Delicates

The Delicates cycle is designed to dry heat-sensitive

items at the low drying temperature.

Time Dry/Air Fluff

The Time Dry cycle can be used to regulate the drying time. Use with any temperature setting. For timed

drying, turn the cycle selector dial to the number of minutes desired. An indicator light will illuminate by

the setting.

Note: Using the Air Fluff temperature setting will I require a longer drying time.

Start the Dryer

After setting the cycle and desired options, press the

cycle selector dial to start the dryer. To pause the cycle, press cycle selector dial again or by opening

the door. To restart the cycle, press cycle selector dial

and cycle will resume from the point of interruption.

Power Off

Turn the cycle selector dial to Power Off to cancel the cycle and stop the dryer.

On dryer models with optional Wrinkle Prevent, the additional 95 minutes of unheated tumbling can be canceled by turning the switch to Off or by opening

the door.

UsingtheControls-ElectronicControls

Features

Cycle Status Lights

The Drying light will illuminate and remain lit until the

dryer enters the cool down portion of the cycle. When

the dryer is in the cool down portion of the cycle, the

Cool Down light will illuminate.

The Wrinkle Prevent and Complete light will illuminate when the dryer has moved into the Wrinkle Prevent

portion of the cycle. On some models, Wrinkle Prevent

will automatically follow the Wrinkle Control cycle. The Complete light will illuminate when the cycle is

complete. The light will remain illuminated until the dryer door is opened or selector dial is moved.

If the dryer is paused during a cycle, the Pause light

will illuminate until the cycle is resumed or the dryer is turned off.

OperutingTips

Clean the Lint Filter

• After each load.

• To shorten drying time.

• To operate more energy efficiently.

filter in place.

i Note: Do not operate the dryer without the lint

Load the Dryer Properly

• Place only one washload in the dryer at a time.

• Mixed loads of heavy and lightweight clothes will dry differently. Lightweight clothes will dry, while heavy clothes may be damp.

• Add one or more similar items to the dryer when only one or two articles need drying. This improves the

tumbling action and drying efficiency.

• Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some

fabrics.

• When drying large, bulky items such as a blanket or comforter, it may be necessary to reposition the load during the cycle to ensure even drying.

[]

Accessories

Optional Drying Rack

Select dryer models are equipped with a drying rack.

The drying rack is useful for drying items that require

no tumble drying, such as tennis shoes, sweaters, stuffed toys or other delicate items.

Note: The Drying Rack, part no. 504105, is

available when not included with your dryer. See your dealer or call 1-877-232-6771 to order.

Care& Cleaning

Control Panel

Clean with a soft, damp cloth. Do not use abrasive substances.

Tumbler

Remove any stains such as crayon, ink pen or fabric dye from new items (such as towels or jeans) with an all-purpose cleaner. Then tumble old towels or rags to

remove any excess stain or cleaning substance. Once

these steps are done, stains may still be visible, but

should not transfer to subsequent loads.

Cabinet

Wipe off any marks with soap and water. Use an appliance wax once a year if desired.

Dryer Exhaust System

Inspect and clean once a year to maintain optimum performance. The outside exhaust hood should be cleaned more frequently to ensure proper operation.

(Refer to the Installation Instructions for more

information.)

Special Laundry Tips

Please follow the care label or manufacturer's instructions for drying special items. If care label instructions are not available, use the following information as a guide.

Bedspreads and • Follow the care label instructions or dry on the Regular cycle. Comforters • Be sure the item is thoroughly dry before using or storing.

• May require repositioning to ensure even drying.

Blankets • Dry only one blanket at a time for best tumbling action.

• Be sure the item is thoroughly dry before using or storing.

Curtains and Draperies

Cloth Diapers Down-Filled

Items Oackets,

sleeping bags, comforters, etc._)

Foam Rubber

(rug hacks,

stuffed toys, certain shoulder

pads, etc.)

Pillows

Plastics

(shower curtains,

outdoor furniture covers, etc.)

• Select the Wrinkle Control cycle to help minimize wrinkling.

• Dry in small loads for best results and remove as soon as possible.

• Select the Regular cycle for soft, fluffy diapers.

• Select the Regular cycle and a Delicate temperature setting.

• Place a clean pair of sneakers in the dryer with the item to fluff the down comforters, etc. Adding a couple of dry towels shortens dry time and absorbs moisture.

• Do not dry on a heat setting. Select the Time Dry/Air Fluff (no-heat) cycle.

• ,_ WARNING - Drying a rubber item with heat may damage it or be a fire hazard.

• Do not dryer-dry kapok or foam pillows.

• Select the Regular cycle.

• Add a couple of dry towels and a pair of clean sneakers to help the tumbling action and to fluff the item.

• Select the Time Dry/Air Fluff cycle on a Delicate or Air Fluff temperature depending on the care label instructions.

ReversingtheDoor

Reversing the Door

Follow these steps to reverse the door:

1. Remove four hinge-attaching screws.

2. Remove all nine screws from door and hinges.

3. Pull bottom of door liner out (A), then pull down (B), removing door liner from door panel.

4. Rotate door panel 180° as shown.

5. Remove door strike from door liner and reinstall on opposite side.

6. Insert liner under flange on bottom of door (A),

then push top of door liner into place (B).

7. Reinstall nine screws removed in Step 2.

8. Using screwdriver, remove two door plugs and reinstall on opposite side of door opening.

9. Reinstall four hinge attaching screws removed in

Step 1.

DryerExhnustTips

Do DON'T

DON'T

Restrict your dryer with a

Let your dryer exhaust

the air easily.

poor exhaust system.

Let a poor exhaust system

cause slow drying.

Use 4 inch

diameter rigid

metal duct. Tape all

joints, including at the dryen

Never use lint-trappingscrews.

El I i

Keep duct runs as straight

as possible.

DON'T

Use plastic, thin foil, or non-metal flexible duct.

DON'T ( I I I

Use longer than necessary

duct runs with many elbows.

Do [

Clean all old ducts before installing your new dryer. Be sure vent flap opens and closes freely. Inspect and clean the exhaust system annually.

DON'T

Allow crushed or clogged ducts and vent.

Troubleshooting

Doesn't Run

Doesn't Heat

Doesn't Dry Properly

Is Noisy

• Be sure the door is shut.

• Check to make sure the electrical cord is plugged in.

• Check fuse or reset circuit breaker.

• Push the control dial in again if the door was opened during the cycle.

• Check fuse or reset circuit breaker.

• Select a heat setting, not air fluff.

• Check that the gas supply is on for gas dryers.

• Clean the lint filter and exhaust duct.

• Dryer timer may have moved into the cool-down portion of the cycle.

Check all of the above, plus...

• Check the exhaust hood outside the house, make sure it opens and closes freely.

• Check exhaust system for lint buildup. Ducting should be inspected and cleaned annually.

• Use rigid 4" metal exhaust duct.

• Do not overload. 1 wash load = 1 dryer load.

• Sort heavy items from lightweight items.

• Large, bulky items like blankets or comforters may require repositioning to ensure even drying.

• Check the washer to be sure it is draining properly to extract water from the load.

• Clothes load is too small to tumble properly. Add a few towels.

• Check the load for objects such as coins, nails, etc. Remove promptly from dryer.

• It is normal to hear the dryer gas valve or heating element cycle on and off during the drying cycle.

• The dryer should be level and installed on a solid floor.

• A clicking noise may be the timer advancing.

• It is normal for the dryer to hum due to the high velocity of air moving through the dryer drum and exhaust system.

Control Knob Advances

Slowly [select models)

Dries Unevenly

Has an Odor • Household odors such as from painting, varnishing, strong cleaners, etc. may enter the

This is normal operation for an Auto Dry or Sensor cycle, especially at the beginning of cycle. Once the load begins to dry, the control knob will start to advance. The rate of advancement will be slow at the beginning of the cycle because there is more moisture in the load. As the load becomes more dry, the control knob will advance more quickly.

Seams, pockets and other similar heavy areas may not be completely dry when the rest of the load has reached the selected dryness level. This is normal. Select the More Dry

setting if desired. If one heavy item is dried with a lightweight load, such as one towel with sheets, it is possible that the heavy item will not be completely dry when the rest of the load has reached the selected dryness level. Sort heavy items from lightweight items for best drying

results.

dryer with the surrounding room air. This is normal as the dryer draws the air from the room, heats it, pulls it through the tumbler and exhausts it to the outside. When these odors are present in the air, ventilate the room completely before using the dryer.

+ 33 hidden pages