Maytag LAT9356AAE, LAT9356AAM, LAT9356AAQ Installation Instructions
Read this before you start…
TOOLS needed for installation:
• Cutting knife
• Channel lock
• Nut driver
• Level
• Crescent wrench
• Screwdriver-flatblade
Proper installation is the responsibility of the purchaser.
SERVICE CALLS PERFORMED AS A RESULT OF POOR INSTALLATION ARE THE
RESPONSIBILITY OF THE INSTALLER.
Make sure you have everything necessary for proper installation.
GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.
STANDPIPE DRAIN SYSTEM must be able to accept 1 1/2” O.D. drain hose. Standpipe
height of 36” is recommended.
NOTE: Unit is designed to pump efficiently to a height of 8 feet at normal spin speeds.
HOT AND COLD WATER FAUCETS must be within 4 feet of the back of the washer.
LAUNDRY TUB DRAIN SYSTEMS (for use with Water-Saver Models only). Tub capacity
to hold a minimum of 21 gallons.
WATER HEATER set to deliver 140°F (60°C) hot water to the washer.
PROTECTION FROM WEATHER: Do not store or operate washer below 60°F (15°C).
2
3
4
5
1
2
3
4
5
6
PARTS supplied for installation:
• 2 inlet hoses
• 4 hose washers
• 2 hose screens
• 1 cable tie
• Literature package
INSTALLATION ACCESSORY KITS
Part No. Description Application
12001875 Grounding Kit Additional grounding if required by local codes.
12001585 Drain Hose Extension Extends drain hose for drain facilities higher than 4 ft.
12001586 Anti-Siphon Used when an air-tight connection exists between
drain hose and drain facility. Floor drain facilities.
12001599 Small Diameter Standpipe Used when standpipe diameter is too small to
Drain Hose receive end of drain hose.
211692 Non-Slip Disc For painted /sloped basement floors.
204986 Carpet Installation Disc For carpeted floors.
1
AUTOMATIC WASHER
INSTALLATION INSTRUCTIONS
LEAVE INSTALLATION INSTRUCTIONS AND
USER’S GUIDE WITH THE OWNER
Printed in U.S.A. 6 2305670
ELECTRICAL
120 Volt 60 Hz 15 AMP Fuse
Individual branch circuit serving only the
washer is recommended.
The washer is equipped with a power cord.
NEVER USE AN EXTENSION CORD.
REQUIREMENTS
EXPORT MODELS – 50 HZ AND 60 HZ
A washer must be used on the voltage and frequency it was designed for. It should be operated on an individual branch circuit and fused
by no less than a 15 amp fuse or circuit breaker for 120 volt units or 10 amp fuse or circuit
breaker on 220–240 volt units. Export models
may require the addition of a plug on the
power cord. It is the responsibility of the
installer to assure that this has been done
properly. Check the data plate to be sure of
voltage and line frequency requirements.
GROUNDING
ELECTRICAL GROUND IS REQUIRED ON
THIS APPLIANCE.
Appliance is equipped with a power cord
having a 3-prong grounding plug for use in a
properly installed and grounded outlet.
Additional Ground Procedure (where local
codes permit):
It is recommended an additional ground be
installed. A proper external ground MUST
be determined prior to wire hookup.
Consult local building officials and qualified
electrician if in doubt.
For additional grounding a grounding kit
(Part No. 12001875) containing accessory
ground wire, clamp, ground screw and
washer can be purchased. Contact your
authorized Maytag dealer for further
assistance. Follow ALL grounding requirements and codes.
EXPORT–specific grounding instructions must
be determined due to variation of electrical
services.
WATER
Water pressure of 20 to 120 p.s.i. is required
to correctly fill the washer to the proper levels.
Pressures of less than 20 p.s.i. may cause a
failure to the water valve. The valve might not
shut off completely.
TO AVOID THE POSSIBILITY OF WATER
DAMAGE, SHOULD A HOSE LEAK,
ALWAYS HAVE FAUCETS ACCESSIBLE
AND TURN OFF FAUCETS WHEN WASHER
IS NOT IN USE.
Loading...