Maxitrol 101310 User Manual

Replaced MP2037
Accessories for Gas Pressure Regulators
All Maxitrol accessories have been designed for universal acceptance among utilities. These accessories can be ordered installed in the regulator, or by bulk quantity. When ordering, indicate part number, name, and size (if any). Include quantity of units desired.
Vent Tube Connector
Threaded sleeve: Two piece assembly where the nut is tightened inside male connector.
No. 11A03 - connects 1/8” female pipe thread to 1/8” O.D.tubing. No. 11A04 - connects 1/8” female pipe thread to 1/4” O.D. tubing.
Nut
Male Connector
Vent Limiting Means
12A04/ 12A09
12A34/ 12A39
Threaded sleeve nut: For RV20V No. 11A08 - 5/16-24 threaded sleeve nut for 1/8” O.D. tube.
Compression tting: Where nut and sleeve are slipped over tubing and tightened into tting body.
No. 11A05-42 - connects 1/4” female pipe thread to 1/4” O.D. tubing. No. 11A05-61 - connects 1/8” female pipe thread to 3/8” O.D. tubing. No. 11A05-63 - connects 3/8” female pipe thread to 3/8” O.D. tubing. No. 11A05-64 - connects 1/2” female pipe thread to 3/8” O.D. tubing.
Optional automatic vent limiting device - ball check permits unobstructed inhalation for fast regulator - diaphragm response on opening cycle, but limits gas escapement to with­in ANSI standards should a diaphragm rupture. When using the vent limiting device, regulator must be mounted in a horizontal upright position for best performance.
No. 12A04 - CSA and CE certied for 14” w.c.
Color - brass. 1/8” NPT. Use on RV48, RV52, RV53, RV61, R400(S). R500(S), R600(S) regulators.
No. 12A09 - CSA and CE certied for 2 psi (LP) and 5 psi (natural) with 325-3, 325-3L.
Color - green. 1/8” NPT.
No. 12A34 - CSA certied with RV81. Color - brass. 3/8” NPT.
Consult with Maxitrol regarding vent limiter use.
No. 12A39 - CSA and CE certied for 2 psi (LP) and 5 psi (natural) with 325-5A, 325-5AL. Color - brass. 3/8” NPT.
Satises ANSI Standards for both natural and LP gas.
Vent Limiting Orice
No. 12A06 - Color - brown. Orice hole is on side of body, under head. Fixed orice
equally limits inhalation and escapement. Use on RV48, RV52, RV53, RV61, R400(S),
12A06
R500(S), R600(S) regulators.
Satises ANSI Standards for both natural and LP gas.
Pressure Tap Connector
No. PF10 - Pressure tap connector installed as part of the control. It is a hose tting
incorporating a captured sealing means for testing inlet and outlet pressures. This
eliminates the need for a special barb tting.
Caution: Vent limiters are not recommended for use in models RV91, RV111, RV131, and 210 Series. Consult Maxitrol regarding vent limiter use in model RV81.
Vent Dampener
No. KVOP-4 - Used on 325-7.
No. KVOP-3 - Used on 325-5.
© 2009 Maxitrol Company, All Rights Reserved
1
Dust Cap
Vent Protectors
Vent Screen
Tamper-Proof Seals
Tamper-proof Seal
Use in vent opening to prevent blockage of breather hole from dust or other foreign particles.
No. 13A09 - for 1/8” NPT vent. Press in plastic cap.
Designed for outdoor applications. Use in vent opening to protect breather hole from rain, snow, dust or insects. Note: Vent protector MUST be mounted in an
upright position.
No. 13A15, 13A15-5 - for 1/8” NPT vent. For outdoor use in 325-3, 325-3L, RV48,
RV52, RV53, RV61, RV81, R500S and R600S. Not a vent limiting device.
Consult Maxitrol regarding other congurations.
Brass, 40 mesh screen ame arrestor for insertion in vent outlet. Prevents ignition
of gas-air mixture which might be present in upper diaphragm chamber.
No. 13A03-1 - for 1/8” NPT vent No. 13A03-2 - for 1/4” NPT vent No. 13A03-3 - for 3/8” NPT vent No. 13A03-4 - for 1/2” NPT vent No. 13A03-6 - for 3/4” NPT vent
Permanent pressure sensitive backed paper. Attempted removal of these seals will destroy the face stock and leave adhesive residue on surface beneath, therefore tampering can be easily detected. Available for all threaded models. Outlet pressure printed on seal.
No. 101310 - for RV12, RV20L, RV47, RV48, R400, RV52, RV53, RV61, RV500,
RV600, 325-3, 325-5A No. 101311 - for RV81, RV91, RV111, 210D, 210E, 210G, 325-7
CHOOSING A VENT ACCESSORY
Note: If leak limiting device is not used, regulator must be vent piped in accordance with government and local codes and regulations.
RV12L - Built-in vent limiting orice with dust cap standard.
RV20L - Built-in vent limiting orice with dust cap standard.
RV20VL - Built-in vent limiting orice with dust cap standard or use
11A08 threaded sleeve nut and run vent line as per code.
RV47 - Must Order: “L” - Integral vent limiting orice, includes dust cap;
or “D” - Integral ball-check limiting device, includes dust cap.
RV48 - 1/8” NPT vent tap. Optional 12A04 or 12A06 vent limiter. Optional 13A09 dust cap. Optional 10A16-2 or 10A16-3 plastic thread protector.
RV48L - integral vent limiting orice.
RV52, RV53, RV61 - 1/8” NPT vent tap. Optional 12A04 or 12A06 vent limiter.
RV81 - 3/8” NPT vent tap. Optional 12A34 vent limiter.
Consult Maxitrol regarding vent limiter use.
RV91 - 1/4” NPT vent tap. 2-½” pipe size.*
RV91 - 1/2” NPT vent tap. 2” pipe size.”
*Caution: Vent limiters are not recommended for use in RV91 models.
Caution: Vent limiters are not recommended for use in RV111 and RV131
models.
210 Series - 3/8” NPT vent tap on 210D.*
210 Series - 1/2” NPT vent tap on 210E.*
210 Series - 3/4” NPT vent tap on 210G & 210J.*
*Caution: Vent limiters are not recommended for use in 210 Series models.
220 Series - Pilot regulator is equipped with 12A06 vent limiting orice,
separate vent line is not required.
325-3, 325-3L - 1/8” NPT vent tap. Optional 12A09 vent limiting device. For outdoor use: optional 13A15 vent protector.
325-5A, 325-5AL - 3/8” NPT vent tap. Optional 12A39 vent limiting device.
325-7, 325-7L - 1/2” NPT vent tap.
R400(S), R500(S), R600(S) - 1/8” NPT vent tap.
Optional 12A09 vent limiting device.
OPD47 - Integral vent limiting orice, includes dust cap.
OPD48, OPD600 - 1/8” NPT vent tap. Optional 12A09 vent limiting device. 12A04 to R400(S), R500(S), R600(S)
RV111, RV131 - 3/4” NPT vent tap.
Maxitrol Company 23555 Telegraph Rd., PO Box 2230
Southeld, MI 48037-2230
GPRAC_MP_EN_05.2009
2
www.maxitrol.com
©2009 Maxitrol Company
All Rights Reserved
Loading...