Maxim MAX1617MEE Datasheet

________________General Description

The MAX1617 (patents pending) is a precise digital
thermometer that reports the temperature of both a
remote sensor and its own package. The remote sensor
is a diode-connected transistor—typically a low-cost,
easily mounted 2N3904 NPN type—that replaces con­ventional thermistors or thermocouples. Remote accu­racy is ±3°C for multiple transistor manufacturers, with
no calibration needed. The remote channel can also
measure the die temperature of other ICs, such as
microprocessors, that contain an on-chip, diode-con­nected transistor.

The 2-wire serial interface accepts standard System
Management Bus (SMBus™) Write Byte, Read Byte,
Send Byte, and Receive Byte commands to program the
alarm thresholds and to read temperature data. The data
format is 7 bits plus sign, with each bit corresponding to
1°C, in twos-complement format. Measurements can be
done automatically and autonomously, with the conver­sion rate programmed by the user or programmed to
operate in a single-shot mode. The adjustable rate allows
the user to control the supply-current drain.

The MAX1617 is available in a small, 16-pin QSOP sur­face-mount package.

________________________Applications

Desktop and Notebook Central Office
Computers Telecom Equipment

Smart Battery Packs Test and Measurement
LAN Servers Multi-Chip Modules
Industrial Controls

____________________________Features

♦ Two Channels: Measures Both Remote and Local

Temperatures

♦ No Calibration Required
♦ SMBus 2-Wire Serial Interface
♦ Programmable Under/Overtemperature Alarms
♦ Supports SMBus Alert Response
♦ Accuracy:

±2°C (+60°C to +100°C, local)
±3°C (-40°C to +125°C, local)
±3°C (+60°C to +100°C, remote)

♦ 3µA (typ) Standby Supply Current
♦ 70µA (max) Supply Current in Auto-Convert Mode
♦ +3V to +5.5V Supply Range
♦ Small, 16-Pin QSOP Package

MAX1617

†

Remote/Local Temperature Sensor

with SMBus Serial Interface

________________________________________________________________

Maxim Integrated Products

1

MAX1617

SMBCLK

ADD0 ADD1

V

CC

STBY

GND

ALERT

SMBDATA

DXP

DXN

INTERRUPT
TO µC

3V TO 5.5V

200Ω

0.1µF

CLOCK

10k EACH

DATA

2N3904

2200pF

___________________Pin Configuration

16
15
14
13
12
11
10

9

1
2
3
4
5
6
7
8

N.C. N.C.

STBY
SMBCLK
N.C.
SMBDATA
ALERT
ADD0
N.C.

TOP VIEW

MAX1617

QSOP

V

CC

DXP

ADD1

DXN
N.C.

GND
GND

__________Typical Operating Circuit

19-1265; Rev 1; 3/98

PART*

MAX1617MEE -55°C to +125°C

TEMP. RANGE PIN-PACKAGE

16 QSOP

EVALUATION KIT

AVAILABLE

_______________Ordering Information

SMBus is a trademark of Intel Corp.

For free samples & the latest literature: http://www.maxim-ic.com, or phone [phone].
For small orders, phone [phone] ext. 3468.

*

U.S. and foreign patents pending.

†

Patents Pending

MAX1617

Remote/Local Temperature Sensor
with SMBus Serial Interface

2 _______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

(VCC= +3.3V, TA= 0°C to +85°C, unless otherwise noted.)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.

VCCto GND..............................................................-0.3V to +6V

DXP, ADD_ to GND....................................-0.3V to (V

CC

+ 0.3V)

DXN to GND..........................................................-0.3V to +0.8V

SMBCLK, SMBDATA,

ALERT, STBY to GND...........-0.3V to +6V

SMBDATA, ALERT Current.................................-1mA to +50mA

DXN Current .......................................................................±1mA

ESD Protection (SMBCLK, SMBDATA,

ALERT, human body model).......................................... 4000V

ESD Protection (other pins, human body model)...............2000V

Continuous Power Dissipation (T

A

= +70°C)

QSOP (derate 8.30mW/°C above +70°C).....................667mW

Operating Temperature Range .........................-55°C to +125°C

Junction Temperature......................................................+150°C

Storage Temperature Range.............................-65°C to +165°C

Lead Temperature (soldering, 10sec).............................+300°C

T

A

= +60°C to +100°C

Monotonicity guaranteed

ADD0, ADD1; momentary upon power-on reset

DXP forced to 1.5V

Logic inputs
forced to V

CC

or GND

Auto-convert mode

From stop bit to conversion complete (both channels)

VCC, falling edge

TA = 0°C to +85°C

VCCinput, disables A/D conversion, rising edge

Auto-convert mode, average
measured over 4sec. Logic
inputs forced to V

CC

or GND.

CONDITIONS

µA160Address Pin Bias Current

V0.7DXN Source Voltage

µA

8 10 12

80 100 120

Remote-Diode Source Current

%-25 25Conversion Rate Timing Error

ms94 125 156Conversion Time

µA

120 180

35 70

Average Operating Supply Current

-2 2

Bits8Temperature Resolution (Note 1)

µA

4

Standby Supply Current

3 10

mV50POR Threshold Hysteresis

V1.0 1.7 2.5Power-On Reset Threshold

°C

-3 3

Initial Temperature Error,
Local Diode (Note 2)

V3.0 5.5Supply-Voltage Range
V2.60 2.80 2.95Undervoltage Lockout Threshold

mV50Undervoltage Lockout Hysteresis

UNITSMIN TYP MAXPARAMETER

TR = +60°C to +100°C
TR = -55°C to +125°C

-3 3
°C

-5 5

Temperature Error, Remote Diode
(Notes 2 and 3)

Including long-term drift

-2.5 2.5
°C

-3.5 3.5

Temperature Error, Local Diode
(Notes 1 and 2)

0.25 conv/sec

2.0 conv/sec

TA = +60°C to +100°C
TA = 0°C to +85°C

High level
Low level

ADC AND POWER SUPPLY

SMBus static
Hardware or software standby, SMB-

CLK at 10kHz

MAX1617

Remote/Local Temperature Sensor

with SMBus Serial Interface

_______________________________________________________________________________________ 3

ELECTRICAL CHARACTERISTICS (continued)

(VCC= +3.3V, TA= 0°C to +85°C, unless otherwise noted.)

STBY, SMBCLK, SMBDATA; V

CC

= 3V to 5.5V

t

HIGH

, 90% to 90% points

t

LOW

, 10% to 10% points

(Note 4)

SMBCLK, SMBDATA

Logic inputs forced to VCCor GND

ALERT forced to 5.5V

STBY, SMBCLK, SMBDATA; VCC= 3V to 5.5V
ALERT, SMBDATA forced to 0.4V

CONDITIONS

µs4SMBCLK Clock High Time

µs4.7SMBCLK Clock Low Time

kHzDC 100SMBus Clock Frequency

pF5SMBus Input Capacitance

µA-1 1Logic Input Current

µA1

ALERT Output High Leakage
Current

V2.2Logic Input High Voltage
V0.8Logic Input Low Voltage

mA6Logic Output Low Sink Current

UNITSMIN TYP MAXPARAMETER

t

SU:DAT

, 10% or 90% of SMBDATA to 10% of SMBCLK

t

SU:STO

, 90% of SMBCLK to 10% of SMBDATA

t

HD:STA

, 10% of SMBDATA to 90% of SMBCLK

t

SU:STA

, 90% to 90% points

ns800

SMBus Data Valid to SMBCLK
Rising-Edge Time

µs4SMBus Stop-Condition Setup Time

µs4SMBus Start-Condition Hold Time

ns500

SMBus Repeated Start-Condition
Setup Time

µs4.7SMBus Start-Condition Setup Time

t

HD:DAT

(Note 5) µs0SMBus Data-Hold Time

Master clocking in data µs1

SMBCLK Falling Edge to SMBus
Data-Valid Time

SMBus INTERFACE

ELECTRICAL CHARACTERISTICS

(VCC= +3.3V, TA= -55°C to +125°C, unless otherwise noted.) (Note 6)

CONDITIONS

Monotonicity guaranteed
TA= +60°C to +100°C

Bits8Temperature Resolution (Note 1)

-2 2

TR= +60°C to +100°C

TA= -55°C to +125°C

°C

-3 3

Initial Temperature Error,
Local Diode (Note 2)

V3.0 5.5Supply-Voltage Range
From stop bit to conversion complete (both channels)
Auto-convert mode

ms94 125 156Conversion Time

%-25 25Conversion Rate Timing Error

-3 3

TR= -55°C to +125°C

°C

UNITSMIN TYP MAX

-5 5

PARAMETER

Temperature Error, Remote Diode
(Notes 2 and 3)

ADC AND POWER SUPPLY

0

6

3

9

12

50 5k 500k50k 5M500 50M

TEMPERATURE ERROR vs.

POWER-SUPPLY NOISE FREQUENCY

MAX1617TOC04

FREQUENCY (Hz)

TEMPERATURE ERROR (°C)

VIN = SQUARE WAVE APPLIED TO
V

CC

WITH NO 0.1µF VCC CAPACITOR

VIN = 250mVp-p
REMOTE DIODE

VIN = 250mVp-p
LOCAL DIODE

VIN = 100mVp-p
REMOTE DIODE

-20

-10

0

10

20

1 10 303 100

TEMPERATURE ERROR

vs. PC BOARD RESISTANCE

MAX1617TOC01

LEAKAGE RESISTANCE (MΩ)

TEMPERATURE ERROR (°C)

PATH = DXP TO VCC (5V)

PATH = DXP TO GND

-2

-1

0

1

2

-50 50 1000 150

TEMPERATURE ERROR

vs. REMOTE-DIODE TEMPERATURE

MAX1617TOC02

TEMPERATURE (°C)

TEMPERATURE ERROR (°C)

SAMSUNG KST3904

MOTOROLA MMBT3904

ZETEX FMMT3904

RANDOM
SAMPLES

__________________________________________Typical Operating Characteristics

(TA = +25°C, unless otherwise noted.)

MAX1617

Remote/Local Temperature Sensor
with SMBus Serial Interface

4 _______________________________________________________________________________________

ELECTRICAL CHARACTERISTICS (continued)

(VCC= +3.3V, TA= -55°C to +125°C, unless otherwise noted.) (Note 6)

Note 1: Guaranteed but not 100% tested.
Note 2: Quantization error is not included in specifications for temperature accuracy. For example, if the MAX1617 device tempera-

ture is exactly +66.7°C, the ADC may report +66°C, +67°C, or +68°C (due to the quantization error plus the +1/2°C offset
used for rounding up) and still be within the guaranteed ±1°C error limits for the +60°C to +100°C temperature range. See
Table 2.

Note 3: A remote diode is any diode-connected transistor from Table 1. T

R

is the junction temperature of the remote diode. See

Remote Diode Selection

for remote diode forward voltage requirements.

Note 4: The SMBus logic block is a static design that works with clock frequencies down to DC. While slow operation is possible, it

violates the 10kHz minimum clock frequency and SMBus specifications, and may monopolize the bus.

Note 5: Note that a transition must internally provide at least a hold time in order to bridge the undefined region (300ns max) of

SMBCLK’s falling edge.

Note 6: Specifications from -55°C to +125°C are guaranteed by design, not production tested.

CONDITIONS UNITSMIN TYP MAXPARAMETER

STBY, SMBCLK, SMBDATA

2.2

Logic Input High Voltage V

2.4

STBY, SMBCLK, SMBDATA; VCC= 3V to 5.5V

V0.8Logic Input Low Voltage

ALERT forced to 5.5V

µA1

ALERT Output High Leakage
Current

Logic inputs forced to VCCor GND µA-2 2Logic Input Current

VCC= 3V
VCC= 5.5V

ALERT, SMBDATA forced to 0.4V

mA6Logic Output Low Sink Current

SMBus INTERFACE

MAX1617

Remote/Local Temperature Sensor

with SMBus Serial Interface

_______________________________________________________________________________________

5

0

10

20

30

50 5k 500k50k 5M500 50M

TEMPERATURE ERROR vs.

COMMON-MODE NOISE FREQUENCY

MAX1617TOC05

FREQUENCY (Hz)

TEMPERATURE ERROR (°C)

VIN = SQUARE WAVE
AC COUPLED TO DXN

VIN = 100mVp-p

VIN = 50mVp-p

VIN = 25mVp-p

-5

5

0

10

50 5k 500k50k 5M500 50M

TEMPERATURE ERROR vs.

DIFFERENTIAL-MODE NOISE FREQUENCY

MAX1617TOC06

FREQUENCY (Hz)

TEMPERATURE ERROR (°C)

VIN = 10mVp-p SQUARE WAVE
APPLIED TO DXP-DXN

0

10

20

0 40 60

80

20 100

TEMPERATURE ERROR vs.

DXP–DXN CAPACITANCE

MAX1617TOC07

DXP-DXN CAPACITANCE (nF)

TEMPERATURE ERROR (°C)

VCC = 5V

0

100

400

200

300

500

0 10.0625 40.25 20.125 0.5 8

OPERATING SUPPLY CURRENT

vs. CONVERSION RATE

MAX1617TOC10

CONVERSION RATE (Hz)

SUPPLY CURRENT (µA)

VCC = 5V
AVERAGED MEASUREMENTS

0

5

15

25

10

20

30

35

1k 100k10k 1000k

STANDBY SUPPLY CURRENT

vs. CLOCK FREQUENCY

MAX1617TOC08

SMBCLK FREQUENCY (Hz)

SUPPLY CURRENT (µA)

VCC = 5V

VCC = 3.3V

SMBCLK IS
DRIVEN RAIL-TO-RAIL

0

3

60

6

20

100

0 31 42 5

STANDBY SUPPLY CURRENT

vs. SUPPLY VOLTAGE

MAX1617TOC09

SUPPLY VOLTAGE (V)

SUPPLY CURRENT (µA)

ADD0,
ADD1

= GND

ADD0,
ADD1
= HIGH-Z

0

25

100

50

75

125

T = -2 T = 8T = 0 T = 4T = 2 T = 6 T = 10

RESPONSE TO THERMAL SHOCK

MAX1617TOC11

TIME (sec)

TEMPERATURE (°C)

16-QSOP IMMERSED
IN +115°C FLUORINERT BATH

____________________________Typical Operating Characteristics (continued)

(TA = +25°C, unless otherwise noted.)

-5

0

5

50 5k 500k50k 5M500 50M

TEMPERATURE ERROR vs.

DIFFERENTIAL-MODE NOISE FREQUENCY

MAX1617TOC03

FREQUENCY (Hz)

TEMPERATURE ERROR (°C)

VIN = 3mVp-p SQUARE WAVE
APPLIED TO DXP-DXN

MAX1617

Remote/Local Temperature Sensor
with SMBus Serial Interface

6 _______________________________________________________________________________________

______________________________________________________________Pin Description

_______________Detailed Description

The MAX1617 (patents pending) is a temperature sen­sor designed to work in conjunction with an external
microcontroller (µC) or other intelligence in thermostat­ic, process-control, or monitoring applications. The µC
is typically a power-management or keyboard con­troller, generating SMBus serial commands by “bit­banging” general-purpose input-output (GPIO) pins or
via a dedicated SMBus interface block.

Essentially an 8-bit serial analog-to-digital converter
(ADC) with a sophisticated front end, the MAX1617
contains a switched current source, a multiplexer, an
ADC, an SMBus interface, and associated control logic
(Figure 1). Temperature data from the ADC is loaded
into two data registers, where it is automatically com­pared with data previously stored in four over/under­temperature alarm registers.

ADC and Multiplexer

The ADC is an averaging type that integrates over a
60ms period (each channel, typical), with excellent
noise rejection.

The multiplexer automatically steers bias currents
through the remote and local diodes, measures their
forward voltages, and computes their temperatures.
Both channels are automatically converted once the
conversion process has started, either in free-running
or single-shot mode. If one of the two channels is not
used, the device still performs both measurements, and
the user can simply ignore the results of the unused
channel. If the remote diode channel is unused, tie DXP
to DXN rather than leaving the pins open.

The DXN input is biased at 0.65V above ground by an
internal diode to set up the analog-to-digital (A/D)
inputs for a differential measurement. The worst-case
DXP–DXN differential input voltage range is 0.25V to

0.95V.
Excess resistance in series with the remote diode caus-

es about +1/2°C error per ohm. Likewise, 200µV of off­set voltage forced on DXP–DXN causes about 1°C error.

SMBus Serial-Data Input/Output, open drainSMBDATA12
SMBus Serial-Clock InputSMBCLK14
Hardware Standby Input. Temperature and comparison threshold data are retained in standby mode.

Low = standby mode, high = operate mode.

STBY

15

SMBus Address Select pin (Table 8). ADD0 and ADD1 are sampled upon power-up. Excess capacitance
(>50pF) at the address pins when floating may cause address-recognition problems.

ADD16

GroundGND7, 8
SMBus Slave Address Select pinADD010
SMBus Alert (interrupt) Output, open drain

ALERT

11

Combined Current Sink and A/D Negative Input. DXN is normally biased to a diode voltage above
ground.

DXN4

Combined Current Source and A/D Positive Input for remote-diode channel. Do not leave DXP floating; tie
DXP to DXN if no remote diode is used. Place a 2200pF capacitor between DXP and DXN for noise filter­ing.

DXP3

PIN

Supply Voltage Input, 3V to 5.5V. Bypass to GND with a 0.1µF capacitor. A 200Ω series resistor is recom­mended but not required for additional noise filtering.

V

CC

2

No Connection. Not internally connected. May be used for PC board trace routing.N.C.

1, 5, 9,

13, 16

FUNCTIONNAME