M-Audio 121002, 1010LT User Manual

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

What’s in the Box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

About the Delta 1010LT Digital PCI Audio Card . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Product Features & Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Breakout Cable 1: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Setting the Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Windows XP,2000, and ME Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Windows 98 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Windows 95 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Windows NT Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Verifying Windows Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Verifying Delta Control Panel Software Installation in Windows . . . . . . . . . . . . . .12

Delta Driver Software Installation on the Mac . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Delta Control Panel Installation on the Mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Delta System Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Delta’s Analog Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

The Digital Monitor Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

The Patchbay / Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Using the Delta 1010LT with your Music Software Application . . . . . . . . . . . . . . .16

Delta 1010LT Control Panel Software - PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Monitor Mixer Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Patchbay/Router Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Hardware Settings Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

S/PDIF Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

About Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Save, Delete, Load Buttons; H/W Installed . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Delta 1010LT Control Panel Software - Mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Patchbay/Router Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Hardware Settings Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

S/PDIF Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Delta 1010LT Recording Tutorials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Typical Setup #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Typical Setup #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Transferring from DAT to Delta 1010LT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Transferring from 1010LT to DAT, monitoring with DAT . . . . . . . . . . . . . . . .47

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Troubleshooting Tips for Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . .52

Before You Call Midiman/M-Audio Technical Support . . . . . . . . . . . . . . . . . . . . . .53

Appendix A- Technical Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Appendix B-If You Use An External Mixer... . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Delta 1010LT - Users Manual

Version:D1010LT-121002

Introduction

Congratulations on your purchase of the Delta 1010L TPCI Audio Card designed and built by M-Audio. The Delta 1010LT is an excellent choice for audio and MIDI production utilizing your PC or Macintosh computer, and will interface easily with professional and “prosumer” recording gear as well as consumer playback devices.

Even if you are experienced in digital recording, please take the time to read this manual. It will give you valuable information on installing your new card and the supporting software, plus help you to fully understand the function and usability of the Delta 1010L T. Once you’re up and running, you will quickly discover the power and brilliance, both in sound and design, of your Delta 1010LT PCI Audio Card.

What’s in the Box?

Your Delta 1010LT box contains:

• This instruction manual.

• Two (2) Delta 1010LT breakout cables.

• The Delta 1010LT PCI host adapter card.

• CD containing drivers & Delta Control Panel software for Windows XP,

2000/ME/98/95/NT and for Macintosh OS 8.5.1 or higher.

• M-Audio Warranty Registration card.

About the Delta 1010LT Digital PCI Audio Card

The Delta 1010LT functions as a 10-input, 10-output digital recording/playback interface with 1x1 MIDI operation. Eight analog inputs and eight analog outputs plus coaxial S/PDIF I/O give you the highest quality analog and digital I/O available -- all with up to 24-bit data width and at any sampling rate from 8kHz to 96kHz. All connections are located on two rugged breakout cables, which also include word clock I/O connectors for superior synchronization between the Delta 1010LT and other word clock capable audio gear.

You can connect your microphone, instrument, mixer, or pre-amp to the Delta 1010LT’s female XLR jacks or the RCA input jacks to monitor and record incoming audio. You can also transfer a digital audio to and from your DAT, MiniDisc, CD, or external A/D converter via the Delta 1010LT’s S/PDIF input and output. The 1010LT also includes the comprehensive Delta Control Panel software, giving you ultimate control over routing plus many other Delta settings including master clock selection and S/PDIF copy protection.

The 1010LT’s XLR jacks will accept balanced mic or line level audio signals, while the RCA inputs are better suited to unbalanced operation. The XLR inputs can be configured to accept either microphone level signals or balanced line level signals, accomplished by setting the jumpers located on the 1010LT PCI card. There are some options to consider, and since this is a decision you may want to make before installing the PCI card, please read the section “Setting the Jumpers” that precedes the “Hardware Installation” section. Finally, line level settings for all inputs and outputs can be controlled via the included Delta Control Panel software.

Within the Delta 1010LT’s PCI chip is a hardware digital mixer. Controlled by the Delta Control Panel software, it may handle all of your mixdown needs, give you extra control of all left, right and stereo levels plus pans, solos, and mutes, or simply give you an alternate or headphone mix.

Quick Start Guide

There may not be any instant tips or tricks for understanding and using an audio interface that is as versatile as the Delta 1010LT. However, we may be able to include some “straight talk” to help light the way.

On the PC: Following the installation procedures for both the Delta hardware and software will enable the 1010L Tfor use in Windows. The Delta 1010LT will become your Windows sound card simply by going to My Computer | Control Panel | Multimedia, and changing Audio settings to one of the Delta stereo pairs. In this way, the Delta card will be the default audio device for your Windows and other media players.

On the Mac: Following the installation procedures for both the Delta hardware and software will enable the 1010LT to be configured for use in a music program that utilizes the ASIO drivers supplied with the Delta. Additionally, the Delta 1010LT can be used in the Apple Sound Manager for your system sounds or in a music/recording program that directs itself to the Sound Manager. The Delta 1010LT will become your Macintosh’s audio device simply by going to the Apple menu | Control Panel | Sound, and changing audio settings from “built-in” to the Delta. In this way, the Delta card will be the default audio device for your Apple applets and a variety of media players. If you wish only to use the Delta with an ASIO compliant music program, leave this setting on “built-in.”

You will, however, need a music/recording software application to take full advantage of the Delta 1010LT as a production tool, and most likely that software will need to analyze and configure the Delta 1010LT--this usually occurs when first launching the program after the Delta 1010LT has been installed. On the PC, the 1010LT is also capable of playing an encoded surround sound signal from the S/PDIF output using some of the DVD player applications that exist on the market. This usually takes some audio output configuration within the player.

The Delta Control Panel controls many of the card’s settings, and includes controls for the digital mixer that is contained on the Delta card. While all of those settings may seem daunting at first, it may help to know that by using only the default settings, the card is ready to playback audio files from your computer (the control panel is set to play audio outputs from software). This can be done from a media player or from your music application, provided the outputs are set to a Delta output port and the software and card are properly configured.

You will be able to hear the Delta inputs under certain conditions. Using a recording program that utilizes the ASIO or EASI drivers with the Delta 1010LT, or (in Windows) using the Windows WDM drivers with programs that take full advantage of them, will allow you to monitor the Delta inputs through the program, and thereby continue to use the default settings in the Delta Control Panel (as mentioned, these are audio outputs from software). When using the Delta card and monitoring in this fashion, there is always some degree of latency, or delay between the the actual input signal and the monitoring of that input signal.

Another way to approach this is by directly monitoring those inputs. This can be done in the Delta Control Panel’s “Patchbay/Router” page by selecting the Delta input and connecting it directly to the Delta output. You can also use the Delta panel’s Monitor Mixer to send the signal at the inputs to the Delta outputs, as well as mix those signals with the software outputs, i.e., your music software sending audio to the Delta outputs. This, and other recording/monitoring scenarios are covered in the Tutorials section toward the end of the manual.

Product Features & Specifications

• 10x10 24-bit/96khz full-duplex recording interface.

• PCI host card with two external, color-coded breakout cables.

• 8x8 analog I/O, balanced on female XLR and unbalanced on gold-plated RCA

connectors, with output line level adjustments selectable within the Delta Control Panel.

• The two balanced analog inputs can be set via hardware jumpers to accept

microphone level signals or line level signals.

• S/PDIF digital I/O supports a variety of settings, including AC3 or DTS surround

(PC only) and copy protection schemes, which can be set via the Delta Control Panel.

• External synchronization up to 100kHz via word clock I/O on BNC connectors.

• 1x1 MIDI I/O on standard DIN jacks.

• High dynamic range (A-weighted measured): D/A 101.5 dB, A/D 99.6 dB.

• Low distortion (measured THD @ 0dBFS): A/D and D/A less than 0.002%.

•Frequency Response: 22-22kHz, -0.2,-0.4dB @48kHz; 22-40kHz,-0.2,-0.7dB @96kHz

• All data paths support up to 24bit/96kHz performance, no upgrades necessary.

• Comprehensive digital mixing, routing, and monitoring capabilities with

included Delta Control Panel software.

• Hardware sample-accurate sync will allow linking of multiple Delta units via S/PDIF.

• Windows XP, 2000/ME and 95/98 multi-card, multi-client drivers with ASIO1

and ASIO2 multi-card, GSIF and EASI drivers included; Windows NT multi-card drivers also included.

• Macintosh control panel and drivers with ASIO1, ASIO2, and legacy ASIO

support for OS 8.5.1 or higher.

Minimum System Requirements

Windows

• Windows 95, 98, NT, ME, 2000 or XP

• Pentium III 500Mhz - (96kHz operation)

• Pentium II 400 - (48kHz operation)

• 128 MB of RAM - (96kHz operation)

64 MB of SDRAM - (48kHz operation)

• UDMA EIDE

Macintosh

• 128 MB of RAM for 96kHz operation.

64MB SDRAM for 48kHz or less.

• Mac G3 with 128 MB of RAM recommended. Some faster Power PCs will

perform adequately.

• Mac OS 8.5.1 or higher.

• UDMA EIDE or fast SCSI HDD recommended.

Breakout Cable 1:

1. Word Clock Input: This female BNC connector is used to input word clock

signals from external sources. The Delta 1010 is capable of synchronizing its sample rate with that of the incoming word clock signal. The input provides built-in 75-ohm termination. The use of 75-ohm coaxial cables (with male BNC connectors) is highly recommended. The connector cover is tan in color.

2. Wo rd Clock Output: This female BNC connector outputs a word clock signal that

is in-sync with the present sample rate clock of the Delta 1010. The output circuitry is designed to drive a word clock signal across 75-ohm coaxial cables and into a device with 75-ohm termination. This connector cover is black in color.

3. Coaxial S/PDIF Input: This RCA connector receives a S/PDIF stereo signal

from your coaxial S/PDIF digital source such as a DAT, MiniDisc player or external A/D converter. This cable is tan in color to denote input, with the connector cover colored red to designate it as a digital input.

4. Coaxial S/PDIF Output: This RCA connector sends a S/PDIF stereo signal to

your coaxial S/PDIF digital target device such as a DAT, MiniDisc player or external D/A converter. This cable is black in color, denoting output.

5. MIDI Input jack: This standard MIDI connector accepts a standard MIDI cable.

Typically a MIDI controller or MTC source would be connected to the Delta 1010LT’s MIDI input jack. The cable is tan in color.

6. MIDI Output jack: This standard MIDI connector accepts a standard MIDI

cable. Typically a MIDI keyboard or sound module would be connected to the MIDI output jack. The cable is black in color.

Breakout Cable 2:

7. Host Cable connector: This 44-pin female D-sub connector is used to attach

the breakout cable to the PCI host card’s male D-sub connector.

8. Analog Inputs 3-8: These jacks input analog audio from a variety of external

sources. Each jack is RCA coaxial and is compatible with RCA coaxial (unbalanced) connections. These cables are tan in color, with the jacks colored white for left and red for right for each stereo pair.

9. Analog Outputs 1-8: These jacks output analog audio to a variety of external

targets. Each jack is RCA coaxial and is compatible with RCA coaxial (unbalanced) connections. These cables are black in color, with the jacks colored white for left and red for right for each stereo pair.

10. Analog Inputs 1-2: These jacks input analog audio from a variety of external

sources. Each jack is female XLR and is compatible with two-conductor (typically XLR or TRS) balanced connections. Inputs 1&2 can be set via jumpers on the PCI card to accept either line level or mic level signals. These cables are tan in color, with the jacks colored white for left and red for right.

PCI Host Adapter Card:

11. Host Cable connector 1: This 15-pin D-sub connector attaches to the supplied

breakout cable #1 to allow communication between the PCI host card and external digital devices.

12. Host Cable connector 2: This 44-pin D-sub connector attaches to the supplied

breakout cable #2 to allow communication between the PCI host card and external analog devices.

13. Line Level Jumper #1: This jumper set allows you to switch the XLR analog

input #1 level setting from balanced microphone level to a +4dBu line level setting. The default setting shown is the microphone level setting.

14. Line Level Jumper #2: This jumper set allows you to switch the XLR analog

input #2 level setting from balanced microphone level to a +4dBu line level setting. The default setting shown is the microphone level setting.

Setting the Jumpers

The Delta 1010LT’s PCI card has two sets of jumpers that can be used to control the operating line level for the 1010LT’s analog inputs 1&2 on XLR jacks. The location of these jumpers is illustrated in the previous section under “PCI Host Adapter Card.”

Two basic settings are possible, one for a microphone line level compatible with low impedance dynamic microphones (those that do not require phantom power, such as condenser mics), and the other is an operating line level of +4dBu (typical for balanced line levels). Two variations are possible for each of these line level settings. This is shown in the illustrations below.

The default setting when you receive your 1010LT is with the jumpers set to the microphone line level setting. If you wish to use either or both inputs 1&2 as a +4dBu line level input, then you will need to change the jumper setting on the 1010L TPCI card.

Changing the jumper setting is easy to do when the 1010LT PCI card is not installed in the computer. Since it is usually impossible to change the jumpers while the card is in the computer, it’s a good idea to make a decision now. If you wish to connect a dynamic or ribbon microphone directly to the Delta 1010LT’s XLR analog inputs 1&2, then leave the jumpers set to their default setting, +4dBu. If you wish to connect the XLR analog inputs 1&2 to the output of a balanced +4dBu device such as a pre amp or dynamics processor, you will need to change the jumper setting.

Remember that you can change one set of jumpers and not the other, if that suits your needs. To change the jumper:

1. Before removing the Delta 1010LT PCI host card from its protective anti-static bag,

touch the metal power supply case of the computer in order to dissipate any static electricity your body may have accumulated. You might want to pick up a grounding wrist strap (available from electronics stores like Radio Shack) if you want to be doubly sure you aren't carrying a static charge that could damage the card.

2. Either hold the PCI card in your hand, or place it on an anti-static surface

(such as its protective bag). Using your fingertips or a tweezer, remove the plastic jumper that is covering the top-most and middle metal pins. See Illustrations 1 and 1a, below.

3. Place the jumper over the middle and bottom-most metal pins. See

Illustrations 2 and 2a, below.

NOTE: Illustrations 1a and 2a show a variation on the mic level

setting and the line level setting, respectively. If you find that your

signal is too hot using the +4dBu selection in the Delta Control

Panel’s “Variable Signal Level” section of the Hardware Settings

page, then try these alternate settings.

Hardware Installation

To mechanically install the Delta 1010LT, do the following:

1. Turn off your computer and unplug the AC cord.

2. Remove the computer’s cover and position the computer so that you may

easily access its PCI slots.

11A 22A

Mic Level

+30dB gain

Mic Level

Attenuates +30dB by 11dB (i.e., +19dB gain)

Line Level

+14dBu peak (+4 mode)

Line Level

Changes Line Level to +3dBu peak (+4 mode)

3. Select the PCI slot where you will install your Delta 1010LT PCI host card.

Make sure the slot is a PCI slot. If you don't know what "PCI slot" means, check the owner’s manual for your computer. PCI slots are distinguishable from ISA slots by being shorter and set back farther from the outside of the computer, however some newer computers have only PCI slots.

4. Before removing the Delta 1010LT PCI host card from its protective anti-static bag,

5. Remove the metal bracket that covers the access hole on the back of the

computer. This bracket is usually fastened to the computer with a single screw.

6. Position the Delta 1010LT PCI host card over the target PCI slot and fit the card

loosely over it with the card in the upright position. Press the card gently but firmly downward into the slot until the card is completely and squarely seated in the slot. If the card seems difficult to seat, a slight rocking motion may help.

7. Screw the Delta 1010LT PCI host card’s metal bracket down into the screw hole

on the back of your computer using the screw you removed in step 5 above.

8. Place the cover back on your computer.

IMPORTANT: Complete the attachment of your Delta 1010LT

breakout cables to the PCI card before powering up your computer.

Never attach a breakout cable to the PCI card while the computer

is on. Doing so could damage the PCI card and void the warranty.

With your computer turned off, it is now time to connect the Delta 1010LT breakout cables to the PCI host card that you have just installed. You may at this time also want to connect to audio gear that you using in conjunction with your Delta 1010LT.

Delta Driver Software Installation - for PC

The Delta 1010LT system includes a driver CD for Windows XP/2000/ME/98/95/NT (and Macintosh, too), containing all Windows drivers and Delta Control Panel software. To install these on your system, please follow these steps:

Windows XP,2000, and ME Installation

1. After installing the Delta 1010LT hardware, boot your system and start

Windows. During the Windows boot procedure, new hardware will be automatically detected by the Add New Hardware Wizard announcing “New Hardware Found.” Click ‘Next>’.

2. The ‘Add New Hardware Wizard’ will now ask how you want to find the

driver. "Search for the best driver for your device" is already selected. Click ‘Next>’.

3. Windows will give you a selection of locations to search. Make sure that only

“Choose a Path” is checked, or click on the check box to do so. Insert the Driver CD into your CD ROM drive. Type in the drive letter of your CD drive (we will assume here that it is D:\) and the path to the Delta drivers, which will be D:\Delta Series\Wdm. Click ‘Next>’.

4. The ‘Wizard’ reports that its Windows driver file search has found the

M-Audio Delta 1010LT. Click Next>. If announcements that “No Driver Signature” pop up, ignore them and continue with the installation procedure.

5. Windows is now ready to install the driver files from the specified location.

Click Next>. Windows will start to copy the files and show you a progress report screen.

6. The Wizard reports that Windows has finished installing the software. Click

‘Finish’. Your Delta 1010LT is ready for action.

After completion of the driver installation, Windows may require you to restart. If it does request a restart, remove the Drivers CD Disk from the CD drive and respond “Yes.” The system will restart and your Delta 1010LT is ready for play.

Windows 98 Installation

1. After installing the Delta 1010LT hardware, boot your system and start

Windows. During the Windows boot procedure, new hardware will be automatically detected by the Add New Hardware Wizard. Click ‘Next>’.

2. The ‘Add New Hardware Wizard’ will now ask how you want to find the driver.

"Search for the best driver for your device" is already selected. Click ‘Next>’.

3. Windows will give you a selection of locations to search. Make sure that only

4. The ‘Wizard’ reports that its Windows driver file search has found the

M-Audio Delta 1010LT. Click Next>.

5. Windows is now ready to install the driver files from the specified location.

Click Next>. Windows will start to copy the files and show you a progress report screen.

6. The Wizard reports that Windows has finished installing the software. Click

‘Finish’. Your Delta 1010LT is ready for action.

After completion of the driver installation, Windows may require you to restart. If it does request a restart, remove the Drivers CD Disk from the CD drive and respond “Yes”. The system will restart and your Delta 1010LT is ready for play.

Windows 95 Installation

1. After installation of the Delta 1010LT hardware, boot your system and start

Windows. During the Windows boot procedure, new hardware will be automatically detected.

2. Choose the Install of "driver from disk provided by hardware manufacturer,"

then click OK.

3. An ‘Install From Disk’ will prompt you to copy files from the

A:\ drive. Insert the Driver software CD into your CD ROM drive. Type in the drive letter of your CD drive (we will assume here that it is D:\) and the path

to the Delta drivers, which will be D:\Delta Products\Delta98 (these drivers also work in Win95). Click ‘Next>’.

4. Windows will start to copy files, with a progress indicator on the screen. Once

this process completes itself, your Delta 1010LT will be ready for action.

Windows NT Installation

1. Power up your computer after physically installing the Delta 1010LT interface

card.

2. Go to Start | Settings | Control Panel and double click on ‘Multimedia.’

3. Click the ‘Devices’ tab, then click the ‘Add’ button.

4. “Unlisted or Updated Driver" will be highlighted at the top of the list. Click

OK.

5. The ‘Install Driver’ box will prompt you to insert the driver disk, and the A:

prompt will appear as the path. Insert the Drivers CD into your CD ROM drive. Type in the drive letter of your CD drive (we will assume here that it is D:\) and the path to the Delta drivers, which will be D:\Delta Products\DeltaNT. Click OK.

6. The "M Audio Delta Interface Card" driver will appear in the Add Unlisted or

Updated Driver dialog box. Click OK.

7. Windows NT will require you to restart your computer for the changes to take

effect. Choose "Restart Now." Upon restart, your Delta 1010LT will be ready for use.

Verifying Windows Driver Installation

Windows displays the Delta 1010LT driver status in the Device Manager page of the System Properties dialog box. The Device Manager page is opened via the W indows Start button: select Start | Settings | Control Panel | System | Device Manager. With the Device Manager displayed, click on the "+" next to "Sound, video and game controllers" to open a list of devices, the Delta 1010L Tbeing a device of that nature. Below is an example view of the Device Manager.

This example shows the M-Audio Delta 1010L Tentry in the Windows Device Manager device list. The Delta 1010LT is properly installed with no conflicts. If you do not see your M-Audio Delta 1010LT in your Device Manager in this fashion, please jump ahead to the "Troubleshooting" section of this manual located on pg 56.

Verifying Delta Control Panel Software Installation in Windows

In Windows, open the Windows Control Panel (do so via Start | Settings | Control Panel). If your Delta 1010L Thardware and Delta Control Panel software are properly installed, the Windows Control Panel should display an "M Audio Delta H/W" icon. By double-clicking on that icon, you can launch the Delta Control Panel software. For convenience, you may also create a shortcut on your desktop by dragging a copy of the "M Audio Delta H/W" icon from the Control Panel to your Windows desktop using your mouse or trackball. After completing the drag operation, a dialog box will ask you if you wish to create a shortcut -click on ‘Yes.’ Once the shortcut is installed, all you have to do is double-click on the shortcut icon on your desktop to launch the Delta Control Panel software.

NOTE: When using a music software program that is ASIO capable,

launch the Delta Control Panel software from within that program.

Some of the control panel functions will be controlled from within

that program, such as master clock setting and sample rate, so it

is desirable to launch the music program first, and then the Delta

Control Panel from the the program’s “launch” or “control panel”

button. Without the music program open however, it is okay to

open the Delta panel from your desktop or other location.

Delta Driver Software Installation on the Mac

1. Open the System folder on your Macintosh hard drive. In the System folder,

locate the Extensions folder.

2. On you Drivers CD disk, open the Mac Delta Drivers folder. Place the

extension file "Delta 1010LT Driver" in your Extensions folder by clicking on it and dragging it to the Extensions folder.

3. If you are using a music program that uses ASIO drivers, it will also have an

ASIO folder within the application’s folder. In your Mac Delta Drivers folder you will find three Delta 1010LT ASIO drivers. For Cubase versions 4.x, use the "ASIO2 Delta1010LT" driver. For Metro, or earlier versions of Cubase, use the "ASIO Delta1010LTv3" driver. For any music program that is not ASIO2 capable, use the “ASIO Delta 1010LT” driver instead (check your program’s documentation). Place the file "ASIO Delta" in your program's ASIO folder by clicking on it and dragging it to the ASIO folder.

3. Drag the "DeltaPanel PPC" file onto your Macintosh hard drive. You can run the

Delta Control Panel from any place that's convenient, though music software applications that use ASIO will allow you to launch the Delta panel from within the program. If not, we suggest creating an alias to the control panel by highlighting it and pressing Command (Apple key)+M. Then, drag the alias to the desktop.

4. With the Delta 1010LT PCI card installed, restarting the computer will load the

Delta 1010LT extension. You will be able to visually see the Delta extension icon pass by as your system loads extension.

5. Go to the Apple menu |Control Panel | Sound. You should see the “built-in” sound

icon, plus the Delta icon if your Delta 1010LT is properly installed. If your music program does use ASIO, you may want to leave the Sound Manager driver set to "built-in" for both Sound In and Sound Out. If your program does not use ASIO (check your software’s documentation) and you will be using the Sound Manager to communicate with your Delta 1010LT, set Sound In and Sound Out to “Delta.” See the section “Hardware Settings Page” in the Delta 1010LT “Control Panel Software” section for information on selecting Sound Manger inputs and outputs.

Your Delta 1010LT is now ready for audio input and output. To configure the Delta for MIDI, you will need to have Opcode’s OMS (Open Music System) installed first. OMSis provided on the CD that came with the unit. Opening the OMS 2.3.7 folder and double-clicking on the “Install OMS 2.3.7” program will install OMS in your system. To install the Delta MIDI driver once OMS is properly installed:

1. Open the “Delta Products”folder on the driver CD, then the Delta 1010LT Mac

folder. Locate the “Delta OMS Driver.”

2. On your Macintosh hard drive, in your System folder, you will find an “OMS

Folder.”Drag the Delta OMS Driver into the OMS Folder.

3. Restart your computer.

To Configure your Delta 1010LT MIDI in OMS, go to the Control Panel or Chooser under the Apple Menu, and make sure AppleTalk is turned off (this is recommended, although OMS will sense that it is on and prompt you to turn it off). If you are configuring OMS for the first time, follow these instructions to configure OMS.

1. In the Opcode folder, which you will find on your hard drive, locate the OMS

Applications folder, "then OMS Setup." Double click on OMS Setup.

2. OMS will inform you that it has not yet been configured. Click OK.

3. The Create A New Studio Setup dialog box now appears. Click OK.

4. The "OMS Driver Search" box asks you to choose the port on which you've

attached the Delta MIDI (either Modem or Printer). DO NOT choose a port, just click "Search." OMS begins Searching.

5. "OMS Driver Setup" shows the "Delta" MIDI in a list when OMS successfully

finds the driver. Click OK. OMS will now define (shows "Identifying") the Delta output port. The "OMS MIDI Device Setup" dialog box will appear showing the Delta's output port with a check box to the left of the port, indicating that the port is enabled. Now click on OK.

6. Next, the "My Studio Setup" appears with a 'file save' dialog box over it. You

will now need to save your new Studio Setup before you can assign an instrument to the Delta's MIDI output and input. Assign your instrument and you are done. You may now exit OMS Setup by quitting the application.

Delta Control Panel Installation on the Mac

The Delta Control Panel may be placed anywhere on your hard drive, or any partition of your hard drive that you find convenient. Once the control panel file has been dragged from the CD onto your hard drive, you may double click it to launch the Delta Control Panel software. You may also create an alias to the control panel by highlighting it, then holding Apple key+M. This alias can then be placed on your desktop.

NOTE: When using a music software program that is ASIO capable,

launch the Delta Control Panel software from within that program.

Some of the control panel functions will be controlled from within

that program, such as master clock setting and sample rate, so it

is desirable to launch the music program first, and then the Delta

Control Panel from the the program’s “launch” or “control panel”

button. Without the music program open however, it is okay to

open the Delta panel from your desktop or other location.

Delta System Basics

Delta’s Analog Inputs/Outputs

The Delta 1010L TPCI Audio Card’ s analog inputs and outputs are compatible with a wide variety of audio products. The Delta Control Panel software allows you to configure the signal level of each analog output individually, or all analog outputs as a group. Signal level settings of +4dBu, “Consumer” (-4dBu), and “-10” are available.

+4dBu is considered a professional operating line level, and is generally associated with balanced, two-conductor cables and connectors such as the 1010LT’s analog inputs 1 & 2. The +4dBu setting will allow you to accept or output a “hotter” signal. The ‘Consumer’ setting is preferred for semi-pro audio equipment and some consumer equipment that can output accept a ‘hotter’ signal than the ‘-10’ setting. The ‘Consumer’ setting offers

approximately 6dB more headroom than does the ‘-10’ setting. Semi-pro and consumer device signal levels vary from manufacturer-to-manufacturer and even product-toproduct, so a little experimentation between Consumer and –10 settings may be required for optimal results.

NOTE: Analog inputs 3 through 8 on the Delta 1010LT do not have

microphone pre-amplifiers built into them. Therefore direct

connection to a microphone is not recommended. Instead run the

microphone signal through a microphone pre-amp (such as the

M-Audio "Audio Buddy™" or M-Audio “DMP2™”) and then connect

the pre-amp output to the input of the Delta 1010LT.

Inputs 1 & 2 are female XLR connectors, and allow connection to balanced microphone or line level audio signals. All other analog jacks on the Delta 1010LT breakout cable are of the RCA (coaxial) variety. The RCA jacks allow connection to unbalanced (typically semi-pro or consumer) connections.

The Digital Monitor Mixer

The Delta 1010LT PCI Audio Card has a hardware digital audio mixer built into its PCI controller chip. It accepts digital audio streams from all hardware inputs and all outgoing software audio devices, mixes them with 36-bit internal precision and then provides the mixed output to one or more locations. For the purpose of monitoring, the output of the mixer may be routed, via the control panel’s Patchbay/Router page, to the first set of Delta 1010LT analog outputs (OUT1/OUT2 as a stereo pair) and/or the S/PDIF digital output. At the same time, the mixer may be used for stereo mix-down, with the mixer’s output recorded into the user’s application software. The digital audio mixer is configured and controlled by the included Delta Control Panel Software.

The Patchbay / Router

In addition to the built-in monitor mixer, the Delta 1010LT PCI Audio Card includes an output patchbay/router. The patchbay/router allows each output (analog or digital) to be connected to a variety of input sources. The 1010LT’s outputs may accept audio from software sources (these output devices are visible in your audio software applications) or from hardware sources such as the analog and digital inputs or the monitor mixer. This capability makes the Delta 1010LT quite flexible for playing and monitoring any audio file format, or directly connecting inputs to outputs for system test purposes.

Synchronization

For proper operation, the entire Delta 1010LT system is always synchronized to a single master clock. The master clock is chosen via the Delta Control Panel software and this clock may be derived from the Delta 1010LT’s internal crystal oscillators, S/PDIF In, or Word Clock In. Most of the time the master clock is taken from the internal crystal oscillators. However, the S/PDIF and Word Clock options are used in situations where the Delta 1010LT must be synchronized to external digital audio or sample rates derived from an external device.

Using the initial default setting, the master clock is derived from the internal crystal oscillators. Operation in this mode is similar to that of a generic sound card – for instance, when an audio file is played through the Delta drivers, the software application playing the audio file is responsible for setting the sample rate in the sound card hardware. The Delta 1010LT supports these sample rates by using either of its internal crystal oscillators and dividing the rate of that oscillator by some value to derive the proper sample rate.

In situations where S/PDIF In is being used, the Delta 1010L Tshould usually be configured to get its master clock from the S/PDIF In data stream. The reason for this is simple – an S/PDIF data stream coming from an external source is rarely going to be in sync with the Delta 1010LT (or other digital audio devices in the system for that matter), even if the sample rates are set the same. If the master clock were set to use the internal crystal, then the incoming S/PDIF audio would have "pops," "crackles," and other undesirable audio artifacts present in it. Instead, setting the master clock to "S/PDIF In" will synchronize the Delta 1010LT to the S/PDIF input data and its digital audio will be transferred properly. There is one special case to consider, however . The external unit sending the S/PDIF digital audio to the Delta 1010L Tmay be "locked" to the word clock emitted from the Delta 1010, or both the external unit and the Delta 1010LTare locked to the same external word clock. In these cases, the Delta 1010LT and the external S/PDIF device are in-sync, and the S/PDIF data would therefore be in-sync with the Delta 1010LT system.

We’ve discussed internal crystals and S/PDIF In as master clock sources. The third option is Word Clock. Word Clock is the desirable choice when you want to synchronize the Delta 1010LT with the word clock of something else in your system. That "something else" may be a another unit that has a word clock output, or it may be a dedicated house word clock generator.

Finally, the Word Clock and S/PDIF In options may be used to operate the Delta 1010LT at non-standard sample rates. When one of these two options is selected, the Delta 1010LT’s sample rate will automatically match that of the incoming word clock or S/PDIF data stream.

NOTE: When either the S/PDIF In or Word Clock is selected

as the master clock source, the Delta 1010LT mixer’s

frequency response will be affected by whatever sample

rates you inject at the S/PDIF In or Word Clock In. This is

because (1) the digital mixer operates at the same sample

rate as the rest of the board, and (2) sample rate and

frequency response are directly correlated.

Using the Delta 1010LT with your Music Software Application

Once the Delta 1010LT’s hardware and driver software are properly installed, it is ready for use with your music application software. Some of these applications may require you to highlight or enable the Delta 1010LT drivers within the program, and others may have a utility that analyzes or profiles the audio cards in your system and enables the drivers. Your software should have an audio device driver setup page.

WINDOWS MME AUDIO INPUT DEVICES: All Delta 1010LT analog and S/PDIF inputs may be used simultaneously for a total of 10 input channels. Within your software application(s), the names of the Delta 1010LT audio input devices are:

PCM In 1/2 Delta-1010LT PCM In 3/4 Delta-1010LT PCM In 5/6 Delta-1010LT PCM In 7/8 Delta-1010LT S/PDIF In Delta-1010LT Mon. Mixer Delta-1010LT

The PCM In devices allow recording a stereo stream directly from the specified analog input pairs. The S/PDIF In device allows you to record a stereo stream directly from the S/PDIF input. The Mon. Mixer device allows stereo recording from the digital "monitor" mixer built-into the Delta 1010LT. The audio data recorded from this device is the mix of input and output streams that is set up in the Delta Control Panel software’s Monitor Mixer page (see Delta 1010LT Control Panel Software section).

Note that all of the input devices are stereo. Your application software may break these down further to "left" and "right" mono devices. Therefore you may see them as "Left PCM In 1/2 Delta-1010L T, Right PCM In 1/2 Delta-1010LT ," "Left S/PDIF In Delta-1010LT, Right S/PDIF In Delta-1010LT," or "Left Mon. Mixer Delta-1010LT, Right Mon. Mixer Delta-1010LT," etc. from within your recording software.

WINDOWS MME AUDIO OUTPUT DEVICES: All Delta 1010LT analog and S/PDIF outputs may be used simultaneously for a total of 10 output channels. Within your software application(s), the names of the Delta 1010LT audio output devices are:

WavOut 1/2 Delta-1010LT WavOut 3/4 Delta-1010LT WavOut 5/6 Delta-1010LT WavOut 7/8 Delta-1010LT WavOut S/PDIF Delta-1010LT

All WavOut devices allow playing a stereo audio stream to the analog hardware outputs (for WavOut 1/2, 3/4, 5/6, 7/8), the S/PDIF hardware output (for W avOut S/PDIF), and/or into the hardware router or mixer. Your application software may break each of these stereo devices down further to "left" and "right" mono devices. Therefore you may see them as "Left WavOut 1/2 Delta-1010LT, Right WavOut 1/2 Delta-1010LT", or "Left WavOut S/PDIF Delta-1010LT, Right WavOut S/PDIF Delta-1010LT", etc. from within your music software. Other software will handle the outputs as stereo pairs, but allow you to pan audio left or right within the pair.

Note that each device name begins with "WavOut." This is to remind you that these are software devices, and not always connected directly to output hardware. Instead they are connected to the Delta 1010LT’s internal patchbay/router and may be sent to one of many destinations. For more on the patchbay/router, see the Patchbay/Router section of the Delta Control Panel software discussion.

ASIO or EASI DRIVER INPUT DEVICES: When using the ASIO or the EASI audio drivers with music programs that support this type of audio, the input devices are displayed as mono devices. Within these software applications, the names of the Delta 1010LT audio input devices are:

Analog In1 Delta-1010LT Analog In2 Delta-1010LT Analog In3 Delta-1010LT Analog In4 Delta-1010LT Analog In5 Delta-1010LT Analog In6 Delta-1010LT Analog In7 Delta-1010LT Analog In8 Delta-1010LT S/PDIF In L Delta-1010LT S/PDIF In R Delta-1010LT Mon. Mixer L Delta-1010LT Mon. Mixer R Delta-1010LT

Notice the S/PDIF In and Monitor Mixer names include "L" and "R" characters. "L" indicates the left channel of the stereo stream, while "R" indicates right channel.

ASIO or EASI DRIVER OUTPUT DEVICES: The Delta 1010LT’s ASIO and EASI output devices appear in stereo pairs. Because each device is stereo, you may see "left" and "right" references within your software application. This allows the application to pan audio left and right under software control. To send a signal to a Delta ASIO output 1 (for example) as a mono output send, one would choose "Analog 1/2 Delta-1010LT" for that track’s output port, and then pan that output hard left. These outputs are named as follows:

Analog 1/2 Delta-1010LT Analog 3/4 Delta-1010LT Analog 5/6 Delta-1010LT Analog 7/8 Delta-1010LT S/PDIF L/R Delta-1010LT

MIDI DRIVERS: The Delta 1010LT MIDI drivers, once enabled in your software’s MIDI Setup, will appear as a MIDI source and a MIDI port within that program’s track configuration windows. The MIDI input driver is named "MIDI In Delta-1010LT," and the MIDI output driver is named "MIDI Out Delta-1010LT." Some software applications allow you to redefine/rename these devices per supplied or manually entered instrument definitions.

WINDOWS MULTIMEDIA SETTINGS: Windows may be set up to use the Delta 1010LT as its default audio device, allowing system sounds to be sent out the Delta 1010LT. This also enables you to use the Delta 1010LT with the sound applets included with Windows. To set this up, go to Control Panel | Multimedia. In the Audio Properties page, set the Playback and Recording devices to the Delta 1010LT input and output devices of your choice.

+ 41 hidden pages