Masterflex 77122-04, 77122-14, 77122-16, 77122-26, 77122-06 Instruction Manual
...
®
OPERATING MANUAL:
PUMP SYSTEM
The MASTERFLEX C/L Pump Systems are small peristaltic
pumps with integral drive motors and are intended for use with
a series of tubing sizes that provide flow rates in the range of
2.0 µL/min to 50 mL/min.
77122-04
77122-14
77122-24
77122-06
77122-16
77122-26
Model No.
A-1299-1073B
Edition 03
(US & Canada only) Toll Free 1-800-MASTERFLEX • 1-800-637-3739
(Outside US & Canada) 1-847-549-7600 • 1-847-381-7050
www.masterflex.com • techinfo@masterflex.com
®
SAFETY PRECAUTIONS
DANGER: Remove power from the Pump System before any cleaning operation is started.
WARNING: Tubing breakage may result in fluid being sprayed from pump. Use appropriate measures
to protect operator and equipment.
Before installing tubing into the Pump Head remove power or shut off the drive. Fingers or loose
clothing could be caught in the rollers.
CAUTIONS:Tubing for use with the MASTERFLEX C/L Pump Systems is Microbore Autoanalysis Tubing. See
Appendix A for specifics. Use of tubing other than that specified will result in poor pumping
performance and/or pump system damage and voiding of applicable warranty.
Do Not pull the tubing too tight. Do not pinch the tubing to cause it to be closed off.
WARNING: PRODUCT USE LIMITATION
These products are not designed for, nor intended for use in patient connected applications; including,
but not limited to, medical and dental use, and accordingly have not been submitted for FDA approval.
TABLE OF CONTENTS
Title Page
SAFETY PRECAUTIONS .......................................................2
INTRODUCTION.....................................................................3
GENERAL DESCRIPTION .....................................................4
SETUP ....................................................................................5
Selecting Tubing Size.......................................................5
Installing Tubing in Pump Head .......................................5
Installing Panel Mount Mounting Brackets .......................6
Installing Rubber Feet ......................................................6
Connecting Primary Power ..............................................6
Backup Battery Connection..............................................6
Remote Start/Stop Connection ........................................6
OPERATION ...........................................................................7
Turning Pump System On and Selecting Direction of
Operation .........................................................................7
Setting Pump Speed ........................................................7
Priming Pump System......................................................7
MAINTENANCE......................................................................7
Cleaning ...........................................................................7
Replacement Parts and Accessories ...............................7
SPECIFICATIONS...................................................................8
WARRANTY............................................................................9
PRODUCT RETURN...............................................................9
TECHNICAL ASSISTANCE....................................................9
APPENDIX A
Available Microbore Autoanalysis Tubing ......................10
Tubing Flow Rates..........................................................11
2
®
NORYL — Reg TM General Electric Company
C-FLEX, PHARMED, TYGON — Reg TM Saint-Gobain Performance Plastics Corp.
VITON — Reg TM E.I. duPont DeNemours & Co.
These products are covered by one or more of the following U.S. and
corresponding foreign patents: D605,286S.
Trademarks bearing the ® symbol in this publication are registered in the U.S.
and in other countries.
PUMP FOR LIQUIDS
ORIGINAL INSTRUCTIONS
3
®
INTRODUCTION
The MASTERFLEX C/L Pump System is designed to pump
fluid through Microbore tubing by means of peristaltic action
at very low flow rates. It is ideal for sanitizers, reagent
dispensing, analyzers, printing systems, controlled feeding
and non-human infusion procedures.
4
®
The MASTERFLEX C/L Pump System,
Figure 1, is enclosed in a plastic 1/4 DIN
Case.
Rubber Feet, supplied with the unit, can be
attached to the bottom of the Case for
operating on a bench or other flat surface
and for stability when stacking multiple units.
The enclosure allows panel mounting using
optional Mounting Brackets (see Accessory
Section for Part No. and page 6 for mounting
instructions).
The Pump System accommodates one tube
at controlled speeds as low as 1.7 rpm.
Tubing is held in place by spring-loaded
Tubing Retainers. For a list of tubing sizes
for use with the Pump System, refer to
Appendix A.
The self-closing Occlusion Bed allows quick
loading or changing of tubing. The Pump
Head Rotor contains four rollers for
minimum pulsation. All units operate from
an External DC Power Supply. The AC
models are supplied with a Universal
Power Supply, which provides a DC
output for connection to the Pump Drive.
The single-turn, adjustable Speed
Control, Figure 2, provides variable flow -
operation. The green PWR On indicator
lights whenever the pump is operating. The
Power On/Direction Switch turns power on
when either clockwise or counterclockwise
pump rotor direction is selected. The MAX
Button is used for priming and purging and
operates the pump at maximum speed while
depressed.
Figure 2. Pump — Front Panel
GENERAL DESCRIPTION
Figure 1. MASTERFLEX C/L Pump System
Pump
Assembly
PWR On
Indicator
MAX: Press and hold to
prime or purge pump
Speed Control: Provides
variable flow adjustment
Power On/Direction
Switch
Bezel
1/4 DIN Case
Mounting
Bracket
(not Supplied)
Universal
Power Supply
Loading...