Master-Bilt E1LZ0040B User Manual
ITEM NO. ______________________________________________________
PROJECT ______________________________________________________
LOCATION _____________________________________________________
DATE _________________________ QTY. ___________________________
Quick Ship
Walk-In Coolers & Freezers
With Matching Refrigeration
Systems
FREE FREIGHT to domestic U.S. locations and select locations
in Canada (consult your Master-Bilt
®
sales representative)
FEATURESFEATURES
CONSTRUCTION
• Models ship within five working
days after order is received
• 4" thick panels
• Coolers, freezers and combo
units available
• Indoor and outdoor models
available
• Single compartment walk-ins
range in size from 5'10" x 5'10"
up to 9'8" x 32'8" and in heights
of 7'2", 7'6", 8'2" and 8'6". They
are available with or without a
floor.
• Combo units range in size from
5'10" x 11'7" to 9'8" x 19'3" and
in heights of 7'6 and 8'6"
• Combo units available in
with-floor freezer/less-floor
cooler and with-floor freezer/
with-floor cooler
• 36" x 78" V-series door
• Interior and exterior wall and
roof finish is 26 gauge acrylic
coated stucco galvanized steel
•.080 textured aluminum interior
floor finish, where required
REFRIGERATION
• Refrigeration is available in either
pre-assembled remote
M-Series systems or PRS-2 packaged systems with standard-duty
and heavy-duty options
• Outdoor models include a
weather hood, membrane
covering for the walk-in roof and
rain canopy for the entry door
• Most indoor models with PRS-2
systems come with a power cord
so the unit can be plugged in and
no piping or components to field
install
WARRANTY
• One-year limited parts and labor,
four-year extended compressor,
15 year panel
OPTIONS
❑ Door & frame kickplates
(shipped loose)
❑ 4 foot fluorescent light
fixtures – shipped loose
(less fluorescent bulbs)
❑ 4 foot LED light fixtures
(shipped loose)
❑ Vinyl strip curtains for entry
doors (shipped loose)
❑ Exterior door ramps
908 Highway 15 North • New Albany, MS 38652
PHONE: 800-647-1284 or 662-534-9061 • FAX: 800-232-3966 or 662-534-6049 • www.master-bilt.com
QUICK SHIP
WALK-IN COOLERS & FREEZERS WITH MATCHING REFRIGERATION SYSTEMS
SPECIFICATIONS
1. Quick Ship Walk-in Coolers or Freezers
A. General
Walk-ins under this program will be constructed of prefab,
precision formed, modular panels designed for accurate,
rapid field assembly and in compliance with the general
construction as described in the Master-Bilt® Architectural
Specifications and General Design Information binder.
Walk-ins and refrigeration systems under this program
will be available for shipment within five (5) working days
of received order.
B. Insulation
Insulation will be 4" thick rigid urethane, pour-type,
foamed-in-place.
C. Heights
Walk-in coolers, freezers or combinations will be available
in 7'6" and 8'6" heights for with-floor applications as well as
with-floor/less-floor combinations. Less-floor applications
will be available in 7'2" and 8'2" heights. Freezers are available in with-floor models only.
D. Metal Finishes
Interior and exterior wall and roof finish of walk-in coolers
and freezers under this program is 26 gauge acrylic coated
stucco galvanized steel. Floor interior finish will be .080
textured aluminum. Floor panels will be designed to support an evenly distributed load of 700 lbs. per square foot
loading (stationary load).
E. Ratings and Listings
Walk-ins under this program have been independently
tested:
• Structural Strength
• A.S.T.M. E-84-94, D-1929-91a, D-482-91, D1622-93
• U.L. and C-U.L. listed doors
• N.S.F. Listed
• N.Y.C. Approval #59-85
• City of Los Angeles RR 25169
• State of Oregon (consult factory)
• City of Houston Approval
• State of Wisconsin Approval
• State of California Bureau of Home Furnishings and
Thermal Insulation Manufacturer Approval
• Type I Fabricator’s License Approval
• State of Florida Approval
• Toxicity Evaluated
• Fully compliant with all Federal EISA requirements
effective January 1, 2009
Reports available from factory on request.
Master-Bilt®’s unique fully
adjustable hinge backing plate
ensures a proper fit of the door
during installation and also allows
for any necessary future
adjustments without removal of
the door or frame.
F. Entrance Door
Stock walk-ins will be complete with one (1) each infitting
(flush-mount) self-closing entrance door. Door dimensions
will be 36" x 78".
Entrance door to include:
• Two (2) spring loaded cam-lift hinges
• Hydraulic door closure
• Deadbolt-locking handle
• Pre-wired compact fluorescent vapor-proof light fixture
• Inside safety release
• Mounted dial thermometer
• Magnetic gaskets along the top and both sides
• An adjustable double vinyl wiper gasket along bottom
• Drip guard over door in outdoor models
In addition, the door will contain adjustable hinge backing
plates for each hinge. These plates will provide for in-field
adjustment of door hinges without removal of the hinges or
door from its frame.
On all walk-in freezers, the infitting door jamb will be
provided with a thermostatically-controlled warmer cable
around the entire perimeter of the opening.
The door will be available either left hinged or right
hinged (specify when ordering).
These doors will be mounted in a 46" wide door frame
and will be interchangeable with any 46" wide wall panel,
thereby allowing placement to fit almost any job-site requirement.
NOTE: Freezer door frame must include one (1) each
heated pressure relief port, factory mounted.
2
Master-Bilt®’s standard
floor finish is an NSF
listed .080 inch aluminum which is textured
for added safety. Floors
are also coved to meet
sanitation guidelines.
All units will contain R-404A refrigerant and will be
designed to operate in ambient temperatures up to 100°F.
Systems for outdoor walk-ins will also contain a crankcase
heater, drainline heater, head master and a weather hood.
Standard warranty includes 18 months limited parts and
labor and extended four year compressor warranty.
A complete list of agency listings and approvals is available from our factory.
4. Warranty
Parts and labor on the walk-ins are covered for one year
with an extended four year coverage on refrigeration system compressor. Panels are covered for 15 years.
2. Remote Refrigeration Systems
A. General
Remote refrigeration systems available for this program are
limited to the Master-Bilt® M-Series condensing units and
evaporator coils on pp. 4-5 only. Condensing units are factory pre-wired and pre-assembled.
All units are provided with matching evaporator coils.
Remote 2 H.P. through 6 H.P. units are available with either
one (1) or two (2) matching evaporator coils.
B. Voltage
Remote
cycle, one phase only. Units ranging from 1 to 4 H.P. are
available in 230 volt, 60 cycle, one phase or 208/220 volt,
60 cycle, three phase. Five and six H.P. units are available in
208/220 volt, 60 cycle, three phase only.
C. Weather Package Kits
Remote condensing units under this program will be provided with weather kits containing a weather hood with
unit base and a low ambient kit.
1
/2 and 3/4 H.P. units are available in 230 volt, 60
3. Packaged Refrigeration Systems
PRS-2 series refrigeration systems consist of a condensing
unit and evaporator coil fully assembled inside a mill finish
aluminum housing. Each system will be provided wired,
piped, evacuated, optimally charged and run tested. All models will be ready to mount on top of a Master-Bilt® walk-in
cooler or freezer. PRS-2 systems may be specified for compartments 13'6" long and under.
Some indoor models will be provided with power cord
for direct plug in to receptacle. Indoor models will also be
supplied with a condensate evaporator pan. Additionally,
systems will contain a factory mounted diffuser with trim
pieces provided loose for finishing box opening on inside.
The evaporator grille is designed to mount flush or recessed
within a 4" thick ceiling panel.
Systems for medium temperature applications are air defrost. Low temperature models will feature electric defrost.
5. Exclusion
Any deviation from these specifications and listed walk-in
sizes does not qualify for this program, and is subject to
Master-Bilt® standard lead time.
Please consult factory for lead times on other walk-in
sizes or specifications.
Master-Bilt reserves the right to discontinue this program
without notice. All specifications are subject to change
without notice.
The standard V-Series entry door is 36"W x 78"H.
3
Loading...