Master-Bilt CL-156 Installation Manual

Installation & Operations Manual

Master-Bilt Products

908 Highway 15 North

New Albany, MS 38652

Phone: (800) 684-8988

PN 090-90000

Rev 05/20/03 LocN.

TABLE OF CONTENTS

Page Numbers INTRODUCTION………………………………….……………………………………………………………4 STORE CONDITIONS..……………….………...……...……………………………….………………….…4 WARNING LABELS AND SAFETY INSTRUCTIONS…………………………………………………….5 PRE-INSTALLATION INSTRUCTIONS……… ……… … ……..…. ………………………………………..6 Inspection for Shipping Damage…………………………………………………………….………6 INSTALLATION INSTRUCTIONS……………………………………………………………………………6 General Instructions………………………………………………………………………………….6 Notice to store owners/ managers………………… …… ………… ……………………………….6

Electrical...………………………………………………………………………………………….… 7 Panel Storage……………………………… ……… …… ………… ……… ……… …………………7 Cam Fasteners………………………..…..………………………………………………………….8 Level Floor…………………………………………………………………………………………….9 Caulking……………………………………………………………………………………………….9 Floor Assembly……………………………………………………………………………………...10 Celing and Wall Penal Assembly……………………… ………… ……… ……… …… ………….10 Door and Frame installation……………………………………………………………………….10 Refrigeration…………………………………………………………………………………………11 Adjusting Door and Replacing Hinges……………………………………………………………11 Door Frame Heater Replacement…………………………………………………………………12 Temperature Controls………………………………………………………………………………12

FINAL CHECK LIST……………………………………… ………… ……… ……… …… ………… ….… …13 SERVICE INSTRUCTIONS…………………………………………………………………………….……13 MASTER-BILT PART NUMBERS………………………………………………………………………….14 SALE AND DISPOSAL………………………………………………..………… ……………… ……… ….14

WIRING DIAGRAMS………………………………… ………………………………………………....15-20

INTRODUCTION

Thank you for purchasing a Master-Bilt cabinet. This manual contains important instructions for installing, using and servicing a Master-Bilt CM/CL-156 case. A parts list is included in with this m anual. Read all these documents carefully before installing or servicing your equipment.

STORE CONDITIONS

The Master-Bilt CM/CL-156 cases are designed to operate in the controlled environment of an air-conditioned store. The store temperature should be at or below 75°F and a relative humidity of 55% or less. At higher temperature or humidity conditions, the performance of these cases may be affected and the capacity diminished. It is not uncommon in a newly constructed store for the temperature and humidity to be above design conditions. These excessive conditions may produce sweating in the case until the store is operational and the ambient environment is more desirable.

The Master-Bilt CM/CL-156 should not be positioned where it is directly exposed to rays of sun or near a direct source of radiant heat or airflow. This will adversely affect the case and will result in poor performance.

NOTICE

Read this manual before installing your cabinet. Keep the manual and refer to it before doing any service on the equipment. Failure to do so could result in personal injury or damage to the cabinet.

DANGER

Improper or faulty hook-up of electrical components of the refrigeration units can result in severe injury or death.

All electrical wiring hook-ups must be done in accordance with all applicable local, regional or national standards.

NOTICE

A refrigeration mechanic and/or a licensed electrician must perform installation and service of the refrigeration and electrical components of the cabinet.

The portions of this manual covering refrigeration and electrical components contain technical instructions intended only for persons qualified to perform refrigeration and electrical work. This manual cannot cover every installation, use or service situation. If you need additional information, call or write us:

Customer Service Depart ment Master-Bilt Products Highway 15 North New Albany, MS 38652 Phone (800) 684-8988 Fax (800) 684-8988

WARNING LABELS AND SAFETY INSTRUCTIONS

This symbol is the safety-alert symbol. When you see this symbol on your cabinet or in this manual be alert to the potential for personal injury or damage to your equipment.

Be sure you understand all safety messages and always follow recommended precautions and safe operating practices.

NOTICE TO EMPLOYERS

You must make sure that everyone, who installs, uses or services your cabinet is thoroughly familiar with all safety information and procedures.

Important safety information is presented in this section and throughout this section and throughout the manual. The following signal words are used in the warnings and safety messages:

DANGER: Severe injury or death will WARNING: Severe injury or death can CAUTION: Minor injury or damage to your cabinet can occur if you ignore the message. NOTICE: This is important installation, operation or service information. If you ignore the

message, you may damage your cabinet.

The warning and safety labels shown throughout this manual are placed on your Master-Bilt Products cabinet at the factory. Follow all warning label instructions. If any warning or safety labels become lost or damaged, call your customer service department at (800) 684-8988 for replacements.

occur if you ignore the message.

CAUTION!

GROUND REQUIRED

FOR SAFE OPERATION

This label is located on top of the electrical control This label is attached to the cabinet power cord on models with a power cord label and on the wiring channel. .

PRE-INSTALLATION INSTRUCTIONS

INSPECTION FOR SHIPPING DAMAGE

You are responsible for filing all freight claims with the delivering truck line. Inspect all cartons and crates for damage as soon as they arrive. If damage is noted to shipping crates or cartons or if a shortage is found, note this on the bill of lading (all copies) prior to signing.

If damage is discovered when the cabinet is uncrated, immediately call the delivering truck line and follow up the call with a written report indicating concealed damage to your shipment. Ask for an immediate inspection of your concealed damage item. Crating material must

be retained to show the inspector from the truck line.

INSTALLATION INSTRUCTIONS

It is the responsibility of the erector to install this walk-in using safe construction practice. The manufacturer is not responsible for the performance of this walk-in if it is not installed in accordance with the instructions detailed in this manual.

GENERAL INSTRUCTIONS

1. Be sure competent service people properly install the equipment.

2. Keep the equipment clean and sanitary so it will meet your local sanitation codes.

3. Rotate your stock so that older stock does not accumulate. A "First-In, First-Out" rotation practice will keep the products in good salable condition.

4. Do not place product in the case when it is soft or partially thawed. Also, product should not be put in the case for at least 6 hours after it is started.

5. Stock cases as quickly as possible, exposing only small quantities to store temperatures for short periods of time.

6. When replacing burned out fluorescent tubes, be sure that the electrical power to the lighting circuit is turned off.

NOTICE TO STORE OWNERS / MANAGERS Moisture or liquid around, under, or inside the cabinet is a potential slip/fall hazard for persons

walking by or working in the general area of the cabinet. Any cabinet malfunction or housekeeping problem that creates a slip/fall hazard around or under the cabinet should be corrected immediately

If moisture or liquid is observed around, under, or inside a Master-Bilt cabinet, an immediate investigation should be made by qualified personnel to determine the source of the moisture or liquid. The investigation should determine if the cabinet is malfunctioning or if there is a drainpipe leaking.

+ 14 hidden pages