Marvel MP24WSG5RS User Manual

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien
ES Instrucciones de instalación, operación y mantenimiento

Wine Cellars
Celliers

Bodegas para vinos

Note: Wine Cellars are designed exclusively for the
storage of wine. Wine Cellars cannot attain storage
temperatures suitable for fresh food storage.

Remarque : Les celliers sont conçues exclusivement
pour y garder des vins. Elles ne peuvent pas atteindre des
températures de conservation convenant à l’entreposage
d’aliments frais.

Nota: Estas bodegas están diseñadas exclusivamente

para el almacenamiento de vino. Las bodegas para vinos
no pueden alcanzar las temperaturas adecuadas para el
almacenamiento de alimentos frescos.

MP24WSG0

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti tip device ................................................6

Product dimensions ............................................................8

Using your Electronic control ............................................10

Starting your appliance ..................................................10

Sleep mode ...................................................................10

Turning your appliance "ON" or "OFF" ..........................10

Adjusting the temperature .............................................10

Interior display lighting ...................................................11

Temperature mode ........................................................11

Control lock ....................................................................11

Alarms ...........................................................................11

Power failure .............................................................11

Door ajar ..................................................................12

Temperature alarm ....................................................12

Temperature sensor error codes ...................................12

Vacation mode ..............................................................13

Shelving congurations ....................................................14

Care and cleaning .............................................................15

Energy saving tips ............................................................16

Obtaining service .............................................................17

Troubleshooting ................................................................18

Warranty ...........................................................................19

Important Safety Instructions

Warnings and safety instructions appearing in this guide
are not meant to cover all possible conditions and situa­tions that may occur. Common sense, caution, and care
must be exercised when installing, maintaining, or operat­ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

!

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

!

CAUTION

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known
to the State of California to cause cancer.

NOTE-Important information to help assure a problem

free installation and operation.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known
to the State of California to cause birth defects or
other reproductive harm..

is committed to building a quality product
in an environmentally friendly manner. Our processes are
tightly controlled and closely monitored. We have achieved

certications in ISO 9001 for quality assurance, ISO 14001

for environmental management, and OHSAS 18001 for oc­cupational health and safety from Lloyd’s Register Quality
Assurance.

2

UNPACKING YOUR APPLIANCE

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts
that could be damaged by movement securely fastened.
Remove internal packing materials and any tape holding in­ternal components in place. The owners manual is shipped
inside the product in a plastic bag along with the warranty
registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has
been thoroughly inspected and found to be in good condi­tion. If there is damage, the packaging will be needed as
proof of damage in transit. Afterwards please dispose of all
items responsibly.

Warranty Registration

It is important you send in your warranty registration card
immediately after taking delivery of your appliance or you
can register online at www.agamarvel.com.

The following information will
be required when registering
your appliance.
Service Number
Serial Number
Date of Purchase
Dealer’s name and address

The service number and serial number can be found on the
serial plate which is located inside the cabinet on the left
side near the top. (See Figure 1).

Online registration

available at

www.agamarvel.com

!

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

Note to Customer

This merchandise was carefully packed and thoroughly
inspected before leaving our plant. Responsibility for its
safe delivery was assumed by the retailer upon acceptance
of the shipment. Claims for loss or damage sustained in
transit must be made to the retailer.

NOTE

DO NOT RETURN DAMAGED MERCHANDISE TO THE
MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

!

CAUTION

XXXXXXXXXXXX

XXXXXXXXXXXX

Figure 1

!

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of
the past. Junked or abandoned refrigerators are still
dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please
follow the instructions below to help prevent acci­dents.

If the appliance was shipped, handled, or stored in other
than an upright position for any period of time, allow the ap­pliance to sit upright for a period of at least 24 hours before
plugging in. This will assure oil returns to the compressor.
Plugging the appliance in immediately may cause damage
to internal parts.

Before you throw away your old refrigerator or
freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not
easily climb inside.

3

INSTALLING YOUR APPLIANCE

Select Location

The proper location will ensure peak performance of your
appliance. We recommend a location where the unit will
be out of direct sunlight and away from heat sources. To
ensure your product performs to specications, the recom­mended installation location temperature range is from 55
to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli­ance. Keep this area open and clear of any obstructions.
Adjacent cabinets and counter top can be installed around
the appliance as long as the front grille remains unobstruct­ed.

!

WARNING

An optional stacking kit, shown in is required to stack
products. Failure to use a stacking kit could result in
personal injury. Contact your dealer or Aga Marvel cus­tomer service at 800-223-3900 to order.

Front Grille,
keep this area
open.

Front Leveling
Legs

Figure 2

Rear

Leveling

Legs

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the
oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher
(by turning the leveling leg out, CCW) and lower (by turning
the leveling leg in, CW) dimensions as shown in Table "A".

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid
scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.
Raise or lower the legs to the required dimension by turning
the legs. Repeat this process for the rear by tilting the appli­ance forward using caution. On a level surface check the
appliance for levelness and adjust accordingly.

!

CAUTION

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex­changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason
it is important this area not be obstructed and the grille
openings kept clean. AGA MARVEL does not recommend
the use of a custom made grille as air ow may be restrict­ed. (See Figure 2).

The front grille screws may be loosened and the grille ad­justed to the desired height. When adjustment is complete
tighten the two front grille screws. (See Figure 5).

4

Figure 3

INSTALLING YOUR APPLIANCE

Do not remove
ground prong

!

WARNING

Electrical Shock Hazard

• Do not use an extension cord with this appliance.
They can be hazardous and can degrade product
performance.

• This appliance should not, under any circumstanc­es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power
cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the
appliance. Doing so may cause an electrical shock,
which may result in severe injury or death.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

Figure 4

This product is factory equipped with a power supply
cord that has a three-pronged, grounded plug. It must be
plugged into a mating grounding type receptacle in accor­dance with the National Electrical Code and applicable lo­cal codes and ordinances (see Figure 6). If the circuit does
not have a grounding type receptacle, it is the responsibility
and obligation of the customer to provide the proper power
supply. The third ground prong should not, under any cir­cumstances, be cut or removed.

Figure 6

Figure 5

Front grille

Front grille screw

NOTE

Ground Fault Circuit Interrupters (GFCI) are prone to nui­sance tripping which will cause the appliance to shut down.
GFCI’s are generally not used on circuits with power equip­ment that must run unattended for long periods of time, un­less required to meet local building codes and ordinances.

5

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

!

WARNING

• ALL APPLIANCES CAN TIP
RESULTING IN INJURY.

Anti-Tip
Bracket

Leveling Leg

• INSTALL THE ANTI-TIP
BRACKET PACKED WITH
THE APPLIANCE.

• FOLLOW THE INSTRUC­TIONS BELOW

Anti-Tip Device

!

WARNING

If your wine cellar is not located under a counter
top (free standing), you must use an anti-tip device
installed as per these instructions. If the wine cellar is
removed from its location for any reason, make sure
that the device is properly engaged with the anti-tip
bracket when you push the wine cellar back into the
original location. If the device is not properly engaged,
there is a risk of the wine cellar tipping over, with the
potential for property damage or personal injury.

211⁄2"

(54.6 cm)

Bottom View of

Wine Cellar

Front of cabinet

Figure 7

Step by step instructions for locating the po­sition of the bracket:

1) Decide where you want to place the wine cellar. Slide it

into place, being careful not to damage the oor, leaving 1"

(2.5 cm) of clearance from the rear wall to allow room for
the anti-tip bracket.

2) Raise the rear leveling legs approximately 1⁄4" (6 mm) to
allow engagement with the anti-tip bracket. Level the unit
by adjusting all the leveling legs as required. Turning the
leveling leg counterclockwise will raise the unit and clock­wise will lower the unit.

NOTE

If installing on a concrete oor, concrete fasteners are

required, (not included with the anti-tip kit).

!

CAUTION

Any nished ooring should be protected with appropriate

material to avoid damage when moving the unit.

Floor Mount Installation

The anti-tip bracket is to be located on the oor in the left or

right rear corner of the wine cellar as shown in Figure 7.

3) Make sure the wine cellar is in the desired location, then

mark on the oor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation
does not allow marking the rear corner of the cabinet, then

make temporary lines on the oor marking the front corner

of the cabinet, excluding the door. Slide the wine cellar out
of the way. From the temporary line extend the sidewall
line back 211⁄2" (54.6 cm) as shown in Figure 8.

4) Align the anti-tip bracket to the marks on the oor so

the side of the bracket lines up with the side of the cabinet
mark, and the "V" notches on the anti-tip bracket line up
with the end of the 211⁄2" (54.6 cm) line (Rear of cabinet
line).

5) Fasten the anti-tip bracket to the oor using the supplied

screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the
rear cabinet leveling leg slides under the anti-tip bracket
engaging the slot.

6

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

NOTE

When the oor mounted anti-tip bracket is used the mini­mum adjusted height of the cabinet is increased by

3

⁄8" (9 mm).

Front of cabinet line

Side of cabinet line

211⁄2"

(54.6 cm)

Figure 8

Rear Leveling leg

Rear of cabinet line

Screw

"V" notches
in bracket

Figure 8a

"V" notches
in bracket

7

PRODUCT DIMENSIONS

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

MP24WSG0

24"

(61 cm)

DOOR STYLE

(G) Glass Frame Door

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

237⁄8"

(60.7 cm)

333⁄4" to 343⁄4"

(85.7 to 88.3 cm)

2323⁄32"

(60.2 cm)

267⁄32"

(66.6 cm)

4613⁄32"

(117.9 cm)

(67.2 cm)

267⁄16"

Figure 10

Figure 9a

"B"

"A"

Figure 9
(G) Glass door

"C"

"E"

shown

"D"

If necessary to gain clearance inside the rough-in
opening a hole can be cut through the adjacent cabi­net and the power cord routed through this hole to a
power outlet. Another way to increase the available
opening depth is to recess the power outlet into the
rear wall to gain the thickness of the power cord plug.
Not all recessed outlet boxes will work for this applica­tion as they are too narrow, but a recessed outlet box
equivalent to Arlington #DVFR1W is recommended for
this application, (see Figure 10).

8

PRODUCT DATA

MODEL

MP24WSG0 115V/60Hz/15A

ELECTRICAL

REQUIREMENTS #

PRODUCT DIMENSIONS

PRODUCT

WEIGHT

140 lbs

(63.6 kg)

"J"

"H"

"D"

"E"

Figure 11

"G"

1"
(2.5 cm)

211⁄2"

(54.6 cm)

"F"

** Minimum rough-in opening required is to be larger than
the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow
all local building codes when installing electrical and appli­ance.

!

WARNING

Floor mount Anti-tip Bracket must be installed for freestand­ing applications. Not required for built in applications.

9

USING YOUR ELECTRONIC CONTROL

Temp

Minus

keypad

On/Off

keypad

Temp

Plus

keypad

Upper/Lower

zones

(Dual Zone

models only)

Display Area

Figure 12
Electronic control

Power Failure

ALARM RESET

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.
Your appliance is shipped from the factory in the "On" posi­tion and will begin start-up of cooling as soon as power is

supplied. If the appliance does not start, conrm that the

wall outlet has power, and that the control is in the "On"
position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic lm. This
lm may be removed by carefully lifting the lm at a corner.

Lights keypad

(glass door

only)

Lock

keypad

System Status

indicators

The sleep mode can be disabled if you prefer to have the
display on continuously. Press and hold the "Lock" key­pad until the display goes past "Loc" and reads "nSL". To
enable the sleep mode, repeat the instruction, again going
past "Loc" until the display reads "SLP".

On initial power up, the control display will indicate a
"Power Failure" alarm. This is a normal condition as the ap­pliance was powered-up at the factory for quality inspection
and then removed from power. A momentary press of the
"On/Off" keypad will reset this alarm condition. (See Alarms
section on page 11).

Sleep mode:

If no keypads are pressed for 60 seconds, the display will
enter sleep mode to conserve power. The control panel will
go dark with the exception of the system status "OK" indi­cator which will remain enabled. Alarm conditions will wake
the display, (see alarms on page 11).

To make the following changes to the control settings
(turning the appliance ON/OFF, adjusting the tempera­ture, changing the interior lights, and activating vaca­tion mode), the control must be awake.

To wake the display press any keypad. A conrm tone will

sound, and the current storage compartment temperature
will be displayed.

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the tem­perature will be shown in the display area of the control.
To turn the appliance "Off", press and hold the "On/Off"
keypad for 4-seconds. "OFF" will now be displayed on the
control.

To turn the appliance "On", press and hold the "On/Off"
keypad for 4-seconds.

Adjusting the temperature:

NOTE

When initially loading your product with warm contents, it
may take up to 48-hours for the storage compartment tem­perature to stabilize.

When making temperature set-point changes, it may take
up to 24-hours for the stored contents to stabilize at your
new set-point temperature.

10

USING YOUR ELECTRONIC CONTROL

Factors that affect the storage compartment stabilized
temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer
set-point temperature.

- Warm content load will delay the change to a colder
set-point temperature.

• Usage, (number and duration of the door openings).

• Use of the storage compartment display lighting, (glass
door product only).

• Installation of the appliance in direct sunlight or next to
a heat source.

To set or check the set-point temperature (with the control
out of sleep mode), press the "-" or "+" keypads. "SET" will
be indicated on the user interface panel and the current

set-point temperature will display and ash. Subsequent

presses of the "-" or "+" keypads will adjust the temperature
colder or warmer respectively. When you have reached
your desired set-point temperature, press the "On/Off" key­pad to accept, or do nothing and the "Set" mode will time­out in 10-seconds accepting the displayed temperature as
the new set-point.

The available set-point temperature range for your appli­ance is 40°F (4.5°C) to 65°F (18.4°C). If you attempt to
adjust the temperature outside of this range you will receive

an audible notication.

Temperature mode:

The temperature mode is preset from the factory in Fahren­heit (°F) but you have the option to change it to Centigrade
(°C). To change the mode, press and hold the "-" keypad,
while pressing the "+" keypad, then release the "-" keypad.
The temperature will now be displayed in Centigrade (°C).
Repeat the procedure to change the temperature mode
back to Fahrenheit (°F).

Control lock:

The control panel can be locked to avoid unintentional
changes. To lock the control, press and hold the "Lock" key­pad until the display reads "Loc" then immediately release

your nger from the keypad. The lock icon will ash 3-times

and then continuously illuminate. When the control panel is
locked, only the Lock keypad, System Status OK indicator
, and the Alarm indicator are active. To un-lock the control
panel, repeat this instruction until the display reads "nLc"

then immediately release your nger from the keypad.

NOTE

If the control lock is active (illuminated lock icon) the control
will have to be unlocked before using the keypad to reset
an alarm condition. See page 11 (Control Lock) for instruc­tions for unlocking the control.

Interior display lighting: (Glass door models only)

Your appliance is equipped with a dual light level display
lighting feature. With the control out of sleep mode press
the "Light" keypad once to activate the interior lighting

display feature at full illumination. A conrmation tone will

sound, and the light bulb "Icon" will illuminate. Pressing
the "Light" keypad a 2nd time will dim the lighting to 50%.
A 3rd press will deactivate the display lighting feature. The
display lighting will automatically deactivate after 4-hours.

Alarms:

The control will alert you to conditions that could adversely
affect the performance of the appliance.

Power Failure

ALARM RESET

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ash. Additionally, an

"ALARM RESET" indicator will be displayed below the
"On/Off" keypad. No audible tone will sound. This alarm
condition can be reset by momentarily pressing the
"On/Off" keypad. If this alarm occurs, it is recommend­ed that you check the condition of any perishables,
even if the appliance is operating normally and the tem­perature has recovered, as prolonged power outages
could result in excessive temperature excursions which
may spoil perishables.

11

USING YOUR ELECTRONIC CONTROL

Door Ajar

ALARM RESET

• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK

indicator will turn-off, the "Door Ajar" indicator will ash,

and a tone will sound every 60 seconds. Additionally,
an "ALARM RESET" indicator will be displayed below
the "On/Off" keypad.

NOTE

The audible alarm can be muted, for each occurrence,
by pressing the lock keypad.

This alarm condition can be reset by closing the door
or momentarily pressing the "On/Off" keypad, (i.e.-if
you are cleaning the storage compartment, etc.). The
alarm will recur in 5-minutes if the alarm condition
persists.

Temp

• Temperature alarm - If the storage compart-

ment temperature deviates excessively from your
set-point temperature for an extended period of time,

the "TEMP" indicator will ash, and an audible tone

will sound every 60 seconds. Additionally, an "ALARM
RESET" indicator will be displayed below the "ON/
OFF" keypad.

ALARM RESET

NOTE

After a high temperature alarm condition, check all perish­ables to ensure they are safe for consumption.

NOTE

The temperature alarm may occur as a result of high usage
or introduction of warm contents to the storage compart­ment. If the temperature alarm continues to occur, your unit
may require service.

NOTE

The audible alarm can be muted, for each occurrence, by
pressing the lock keypad.

This alarm condition can be reset by momentarily pressing
the "On/Off" keypad. If this alarm occurs it is recommended
that you check the condition of your stored contents, even
though the appliance is operating normally and the temper­ature has recovered, as prolonged temperature excursions
could spoil perishables.

Door Ajar

NOTE

Multiple alarms are possible, i.e.- "Door Ajar" for a pro­longed period may trigger a "Temp" alarm, in which case
both "Door Ajar" and "Temp" indicators will activate.

Temp

Temperature Sensor Error Codes

The temperature sensors are monitored continuously. Any
OPEN or SHORTED circuit condition will initiate an
ERROR CODE as listed below:

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Single Zone

Temperature Sensor

Defrost Sensor

Failed temperature sensor in the single

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-

Call service to have the tem-

perature sensor replaced.

Unplug the power cord imme-

diately and call service to have

the defrost sensor replaced.

rounding oor.

12

USING YOUR ELECTRONIC CONTROL

Vacation mode:

This operating mode can be used to save energy during
high cost energy periods, or when you won't be using your
appliance for an extended period of time by disabling the
lights, alarm tones, and keypad entry tones. Vacation mode
also serves as a Sabbath mode, disabling functions and
its controls in accordance with the weekly Sabbath and
religious holidays observed within the Orthodox Jewish
community. When used as Sabbath mode, you may open
or close the door at any time to access contents without
concern of directly turning on or off any lights, digital read­outs, solenoids, fans, valves, compressor, icons, tones, or
alarms.

When activated, the display, alarm indicators and tones,
keypad touch tones, interior lights, and all options are dis­abled. All keypad functions are disabled, with the exception
of the "On/Off" keypad which is required to exit Vacation­mode. Storage compartment temperatures are monitored
and controlled at the settings prior to entering Vacation
mode.

To enter Vacation Mode (with the control out of sleep
mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ash

"VAC" 3-times to acknowledge your request, then will
display "VAC" continuously until Vacation mode is exited.
A power outage will not exit Vacation mode, exiting can
only be accomplished manually. To exit Vacation mode and
return to normal operation, press and hold the "On/Off"
keypad until the control displays the temperature.

13

SHELVING CONFIGURATIONS

SHELF REMOVAL AND INSTALLATION

Shelving Congurations

Your Marvel Professional Series appliance is equipped with
full extension ball bearing shelf glides to provide maximum
access and visibility for the product stored on the shelving
arrangements listed below.

Figure 13

Single Zone Wine Cellar:
24" (61 cm) Wide models:

(5) 8 bottle wire racks
(2) 4 bottle half-depth wire racks

To remove a shelf:

Extend the shelf out of the cabinet until it stops.

Unload the shelf (see Figure 14).

Depress the locking tabs on both sides of the shelf and pull
the shelf straight out (see Figure 14a). When the shelf is
removed, push the extended cabinet mounted shelf exten­sions back into the cabinet.

To re-install a shelf:

Pull out the cabinet mounted shelf extensions to assist the
engagement with the wire rack shelf.

Insert the wire rack side track into the cabinet mounted
shelf extensions on both sides.

Push the wire rack completely into the cabinet to engage
the locking tabs.

Pull the shelf out, (unloaded), to verify the wire rack is
locked into the side rails. If the wire rack falls out, the lock­ing tabs are not engaged; repeat the installation.

Load the shelf as required.

Remove the wine from
the shelf to be removed

Locking tab

14

Figure 14

Figure 14a

CARE AND CLEANING

Front Grille

Be sure that nothing obstructs the required air ow open­ings in front of the cabinet. At least once or twice a year,
brush or vacuum lint and dirt from the front grille area (see
page 4).

!

SHOCK HAZARD: Disconnect electrical power from the
appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap
and water and thoroughly rinsed with clear water. NEVER
use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do
NOT use an abrasive cleaner, solvent, polish cleaner or
undiluted detergent.

CAUTION

Care of Appliance

1. Avoid leaning on the door, you may bend the door
hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop­ping near the front of the appliance. Damage to the
grille can occur.

3. Periodically clean the interior of the appliance as
needed.

4. Periodically check and/or clean the front grille as
needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos­sible. Minimize the number of door openings while the
power is off so as not to adversely affect the appliance's
temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the
appliance. This component is very reliable, but should one

fail, contact a qualied service technician for replacement

of the LED.

!

CAUTION

Never try to remove a loaded shelf, remove everything from
the shelf before removing. Use both hands when removing
the shelf.

15

ENERGY SAVING TIPS

The following suggestions will minimize the
cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance
(cooker, dishwasher, etc.), heating air duct, or other
heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be­neath door are not obstructed and kept clean to allow
ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not
shared with other appliances).

5. When initially loading your new product, or whenever
large quantities of warm contents are placed within
refrigerated storage compartment, minimize door
openings for the next 12 hours to allow contents to pull
down to compartment set temperature.

6. Maintaining a relatively full storage compartment will
require less appliance run time than an empty compart­ment.

7. Ensure door closing is not obstructed by contents
stored in your appliance.

8. Allow hot items to reach room temperature before plac­ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature
that meets your personal preference and provides the
proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem­ perature for the stored contents.

12. Set the control to the “off” position if cleaning the

appliance requires the door to be open for an extended
period of time.

13. For wine storage products:

When serving temperatures are not required,
return the compartment(s) set temperature to the
ideal red and white wine long term storage tem­ perature of 13°C / 55°F.

16

OBTAINING SERVICE

If Service is Required:

• If the product is within the rst year warranty period
please contact your dealer or call AGA MARVEL Cus­tomer Service at 800.223.3900 for directions on how to
obtain warranty coverage in your area.

• If the product is outside the rst year warranty period,
AGA MARVEL Customer Service can provide recom­mendations of service centers in your area. A listing
of authorized service centers is also available at www.
agamarvel.com under the service and support section.

• In all correspondence regarding service, be sure to
give the service number, serial number, and proof of
purchase.

• Try to have information or description of nature of the
problem, how long the appliance has been running, the
room temperature, and any additional information that
may be helpful in quickly solving the problem.

• Table "A" is provided for recording pertinent information
regarding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name
Dealer’s Address
Dealer’s City
Dealer’s State
Dealer’s Zip Code
Appliance Serial Number
Appliance Service Number
Date Warranty Card Sent (Must

be within 10 days of purchase).

Table A

17