Martin Pro RUSH MH 6 Wash CT Specifications



G A L L E R Y

RUSH MH 6 Wash CT

The RUSH MH 6 Wash CT is designed for key lighting applications
within the House of Worship, Performing Arts and Live Stage
environments where color temperature control of white light is critical
but also a compact and light weight design is desired for smaller
applications

The RUSH MH 6 WASH CT is a bright single-lens LED moving head
with fully premixed white color temperatures. With twelve 10W
WW/CW (warm white and cold white) LEDs and a 10° to 60°
motorized zoom, it offers full electronic dimming and variable strobe
effects controlled via DMX.

Pre mixed white light ranging from 2,700K to 7,800K

10

-60 Degree Zoom System

Compact and Lightweight Design

F E A T U R E S

T E CHNI CA L S P E CI F I CA T I O NS

Physical

Dynamic Effects

Control and Programming

Optics

•

2,700K to 7,800K Color Temp Range

•

Allows key lighting to be matched for multiple sources from Tungsten to
Metal Halide

•10-60 Degree Zoom System

•

Compact and lightweight design

•

Can be used as a Mid effect with a tight beam look to washing a
stage for key lighting applications

•

Ideal for applications that have limited ceiling height or weight
restrictions.

Length: 290 mm (11.4 in.)
Width: 189 mm (7.4 in.)
Height: 360 mm (14.2 in.)
Weight: 7.1 kg (15.7 lbs.)

Color temperature: 2700 K - 7800 K
Color temperature presets: 2700 K to 7800 K in ~100 K steps
Electronic dimming: 16-bit, 0 - 100%, four dimming curve options
Strobe and pulse effects: Variable speed and action, random strobe
Electronic 'shutter' effect: Instant open and blackout
Zoom: Motorized, 10 - 60°
Pan: 540°, 16-bit control
Tilt:

220°, 16-bit control

Control options:

DMX
DMX channels: 12
16-bit fine control: Dimming, pan and tilt
DMX address setting: Control panel with LCD display
DMX compliance: USITT DMX512/1990

Light source: 12 x 10 W CWUW LEDs
Minimum LED lifetime: 50 000 hours (to >70% luminous output)*
Zoom range: 10° - 60°

*Figure obtained under manufacturer's test conditions:



©

2015 Martin Professional

Olof Palmes Allé 18 • 8200 Aarhus N • Denmark • Phone: [phone] • Fax: [phone] • www.martin.com

Images contained in this brochure have been converted to CMYK and

are not necessarily representative of actual colors. Specifications are subject to change without notice

Construction

Installation

Connections

Electrical

Typical Power and Current

Thermal

Approvals

Included Items

Accessories

Related Items

Ordering Information

Housing: High-impact flame-retardant thermoplastic

Color: Black

Ingress protection rating: IP20

Mounting points: One quarter‐turn bracket for rigging clamp

Location: Indoor use only, must be fastened to surface or structure

Orientation: Any

Minimum distance to illuminated surfaces: 200 mm (8 in.)
Minimum distance to combustible materials: 100 mm (4 in.)
Minimum clearance around fans and vents: 100 mm (4 in.)

AC power input: Neutrik PowerCon
AC power throughput: Neutrik PowerCon
DMX data in/out: 3-pin and 5-pin locking XLR

AC power: 100-240 V nominal, 50/60 Hz
Power supply unit: Auto-ranging electronic switch mode
Fuse: T 3.15 A
Recommended Miniature Circuit Breaker*: Type D

* Per IEC 60898/UL489/CSA C22.2 No. 5:
Power consumption figures are typical, not maximum. Allow for +/-10% variation.:

120 V, 60 Hz: 1.3 A, 150 W, PF 0.99
230 V, 50 Hz: 0.7 A, 150 W, PF 0.94
Typical half-cycle RMS inrush current at 240 VAC: 11.3 A

Measurements made at nominal voltage with all LEDs at full intensity. Allow for a
deviation of +/- 10%.:

Cooling: Forced air (temperature-regulated, low noise)
Maximum ambient temperature (Ta max.): 40° C (104° F)
Minimum ambient temperature (Ta min.): 0° C (32° F)

EU safety: EN 60598-2-17 (EN605989-1), EN 62471, EN 62493
EU EMC: EN 55015, EN 55032, EN 55103-2, EN 61000-3-2, EN 61000-3-3, EN 61547
US safety: UL 1573, UL 8750
US EMC: CFR Title 47 Part 15
Canadian safety: CSA C22.2 No. 166
Australia/NZ: C-TICK N4241 / RCM

Power input cable, 6 A, 18 AWG, UL, 0.75 mm2, H05VV-F, 1.5 m (4.9 ft.), without mains
plug
Omega bracket for rigging clamp attachment

Cables:

Power input cable, 14 AWG, UL, SJT, 1.5 mm2, H05VV-F, with PowerCon input
connector, 3 m (9.8 ft.): P/N 11541508
Power relay cable, 14 AWG, UL, SJT, 1.5 mm2, H05VV-F, with PowerCon connectors,

1.4 m (4.6 ft.): P/N 11541509
Power relay cable, 14 AWG, UL, SJT, 1.5 mm2, H05VV-F, with PowerCon connectors,

2.25 m (7.4 ft.): P/N 11541510
Power relay cable, 14 AWG, UL, SJT, 1.5 mm2, H05VV-F, with PowerCon connectors,

3.25 m (10.7 ft.): P/N 11541511

Power connectors:

Neutrik PowerCon NAC3FCA power input connector, cable mount, blue: P/N 05342804
Neutrik PowerCon NAC3FCA power output connector, cable mount, light grey: P/N
05342805

DMX link

DMX termination plug, 3-pin male XLR: P/N 91613017

Installation hardware:

Half-coupler clamp: P/N 91602005
G-clamp: P/N 91602003
Quick-trigger clamp: P/N 91602007
Safety cable, safe working load 50 kg: P/N 91604003

RUSH™ Software Uploader 1: P/N 91611399

RUSH™ MH 6 Wash CT in cardboard box: P/N 90280090



©

2015 Martin Professional

Olof Palmes Allé 18 • 8200 Aarhus N • Denmark • Phone: [phone] • Fax: [phone] • www.martin.com

Images contained in this brochure have been converted to CMYK and

are not necessarily representative of actual colors. Specifications are subject to change without notice