All Rights Reserved. This document may not be copied.
Page 2
We appreciate your video encoder purchase.
Before installing the product, please read the following with care.
Trademarks
Other trademarks used in this document are registered trademarks or manufacturer or vendor
trademarks associated with the products.
Disclaimer
Product options and specifications can be changed without notice. The information in this manual is
furnished for informational use only and should not be construed as a commitment by Marshall
Electronics, Inc. Marshall Electronics, Inc. assumes no responsibility or liability for any errors or
inaccuracies that may appear in this publication.
Safety Precaution
Make sure to turn off the power before installing video encoder.
Do not install under direct sunlight or in dusty areas.
Make sure to use the product within the temperature and humidity specified.
Do not operate the product in presence of vibrations or strong magnetic fields.
Do not put electrically conducting materials in the ventilation hole.
Do not open the top cover of the products. It may cause a failure or electric shock on the
components.
Make sure to leave a space of at least 10 cm from the ventilation hole in order to prevent
overheating.
Check voltage and current requirements before connecting a power supply.
This User Manual provides information on installation setup, operation of the video
encoder, as well as troubleshooting tips.
1.2 Features
Video Encoder is a video and audio transmission system that provides broadcast
quality audio and video, based on IP network through LAN, ADSL/VDSL, and wireless
LAN. An Encoder System compresses and transmits media data, while a Decoder
System receives and decompresses media data.
Video
Highly Efficient Compression Algorithm; H.264 & MJPEG support
Wide range of Transmission Rates: 32kbps ~ 16mbps
Various Transmission Modes: CBR or VBR
Motion Detection
Audio
Multi-Transmission Mode: Uni-Directional Mode (IP Encoder to Client PC or
Decoder/ Client PC or Decoder to IP Encoder), Bi-Directional Mode
Network
Fixed IP & Dynamic IP (DHCP) support
1:1, 1:N support
Multicasting
Automatic Transmit Rate Control according to network conditions
OnVIF, PSIA compliant
Serial Data
RS-485 support
Data Pass-Through Mode: Serial Data Communication between IP Encoder and
Decoder
Data Pass-Through Mode: Serial Data Communication between Encoder-Decoder
Sensor and Alarm
Supports direct connections of External Sensor and Alarm Devices
Event Alarm
User Manual VS-103E-3GSDI – V1.0Page 4 of 63 2/2016
Page 5
1.Introduction
USB
Connection to internal or external USB storage for remote access, recording and
playback
User Interface
Diagnose and upgrade through dedicated program called VS Manager
System Configuration using Internet Explorer
High Reliability
Reliable Embedded System
System Recovery by Dual Watch-Dog Functions
1.3 Products and Accessories
User Manual VS-103E-3GSDI – V1.0Page 5 of 63 2/2016
Page 6
1.Introduction
No.
Parts
Function
1
LED
Display System Status
2
Audio Input
Audio Input
3
Audio Output
Audio Output
4
HDMI Input
HDMI Video & Audio Input
5
HDMI Output
HDMI Video & Audio Output
6
USB Port
USB 2.0
7
LAN
1000/100/10MB Base-T Ethernet
8
Reset Button
Initialization of Network Setting
9
Sensor
Sensor Input
10
Alarm
Alarm or Relay Output
Part Names and Functions
Front View
User Manual VS-103E-3GSDI – V1.0Page 6 of 63 2/2016
Page 7
1.Introduction
No.
Parts
Function
1
Power
DC +12V Power Input
2
RS-422/485
Serial Port for PTZ Control
3
RS-232
Serial Port for PTZ Control
4
Composite In/ Output
Composite Video Input / Output
5
3G/HD/SD-SDI
In/Output
3G/HD/SD-SDI Video & Audio
Input / Output
System Mode
Video
Audio
Serial Data
Encoder
Transmit
Transmit/Receive
Transmit/Receive
Decoder
Receive
Transmit/Receive
Transmit/Receive
Rear View
1.4 System Connections
Video Encoder operates as one mode; Encoder. Video Encoder Systems can be
connected in either 1-to-1 where one encoder is connected to one decoder or 1-to-multiple where one encoder connected to many decoders.
The following chart shows status of video, audio and serial data on each mode:
The system mode is defined by the video communication and this system mode is
capable of single directional transmission of audio and/or bi-directional serial data.
User Manual VS-103E-3GSDI – V1.0Page 7 of 63 2/2016
Page 8
1. Introduction
Encoder
Decoder
Site
Remote Center
Encoder
Decoder
Decoder
Decoder
Remote Center
Site
Topology
Generally, the Encoder and Decoder are connected in 1-to-1 mode. To support this
specific situation, 1-to-multiple connection is also supported.
1:1 Connection (Unidirectional Transmission)
The most commonly used configuration is 1-to-1 connection. An Encoder is installed
at a site where video images can be transmitted and a Decoder is installed at a center
location to receive and view the video images on monitors. Audio and Serial data are
transferred in either direction. An Encoder and Decoder can be connected by setting
the Encoder’s Address for the Decoder’s Remote IP.
1:N Connection (Uni-Directional Transmission)
In this configuration, a site can be monitored from many remote center locations.
Maximum connections would be limited by the network bandwidth.
Functionally, the VMS (Video Management System) software can replace the
decoder.
User Manual VS-103E-3GSDI – V1.0Page 8 of 63 2/2016
Page 9
1. Introduction
Encoder
Decoder
Decoder
Site
Remote Center #1
Remote Center #2
Multicast Mode
In the Network Supporting Multicast Mode, if Multicast is setup as a system protocol,
you can use bandwidth efficiently regardless of the number of decoders. In the 1:N
connection, a large number of decoders can receive audio and video data from an
encoder by using a single streaming transmission.
Relaying
In this arrangement, video and audio can be re-transmitted from one center to another
center. The arrangement is useful when the network bandwidth at the site is limited
while there is more than one center wanting to monitor the site.
User Manual VS-103E-3GSDI – V1.0Page 9 of 63 2/2016
Page 10
1. Introduction
VMS (Video Management System)
VMS (Video Management System) is a Windows based remote monitoring program to
access multiple encoders for real-time monitoring or control of the encoders and
connected cameras. Please refer to the VMS User Manual for more information on
VMS.
User Manual VS-103E-3GSDI – V1.0Page 10 of 63 2/2016
Page 11
2.Installation
2.1 Connecting Video
Encoder System
Connect a video encoder video output line to the encoder video input port.
Connecting with Megapixel Encoder
Connect a video encoder which supports HDMI or HD-SDI output to the HDMI or
HD-SDI Input port of video encoder accordingly.
Connecting with D1 Resolution Encoder
Connect a video encoder to the video input port of video encoder accordingly.
Decoder System
Connect a monitor to either the HDMI or COMPOSITE (HD-SDI) Output port of
video encoder accordingly.
2.2 Connecting Audio
Audio is Full-Duplex. It is possible to set the mode as Tx-only, Rx-only, or Tx-Rx.
Connect audio input and output ports to audio devices accordingly.
The Audio signal required is line level, so audio equipment with an amp, mixer or
other amplifier should be used.
2.3 Connecting Serial Ports
For encoder control, the PTZ Controller (keyboard) and Receiver can be connected to
Serial Ports. Two corresponding Serial Ports in the Encoder and Decoder which are
connected 1-to-1, works in Pass-Through Mode. This means that commands at a local
system’s COM1 Port will be transparently passed to the remote system’s COM1 Port.
Commands at a local system COM2 Port will pass to the remote system’s COM2 Port.
2.4 Connecting Sensor and Alarm
Connect Sensor and Alarm Devices to corresponding terminals accordingly.
2.5 Connecting Power
After confirming the Power Source, connect Power Adaptor and connect the 12VDC
Connector to the System.
User Manual VS-103E-3GSDI – V1.0Page 11 of 63 2/2016
Page 12
2.Installation
2.6 Check If It Works
Once the power is supplied to the encoder, it will start booting. The system will boot up
to operation mode after approximately 40-60 seconds. The green LED on the Ethernet
Port will flash indicating the system is ready.
Software provided on the disc called VS Manager allows you to check the IP address
and other network details of the video encoder. Please refer to the VS Manager
manual for instructions on how to find the IP address of the video encoder and to make
necessary changes.
Encoder LED Display
The LED’s above show that the Encoder is connected but a Decoder is not. Once
an Encoder is connected to a Decoder, the color of the “LINK” LED Display will turn
green and the “DATA” LED will blink as video or audio transmissions occur.
Decoder LED Display
These LED’s above show that the Decoder has started without connecting to an
Encoder. Once an Encoder is connected, the color of “LINK” LED Display will turn
green and the “DATA” LED will blink as video or audio data transmissions occur.
User Manual VS-103E-3GSDI – V1.0Page 12 of 63 2/2016
Page 13
2.Installation
LED
State
Description
PWR
OFF
Power OFF
Red
Power ON
STATUS
Green Blinking
Normal Operation
Red
System Failure: Needs Diagnostics
Constant Change
between Red and
Green
NTSC/PAL setting does not match with
Input Video Signal
Red Blinking
Failed to obtain IP Address in DHCP Mode
Constant Change
between Green
Blinking 2 Times and
Red Blinking Once
Failed to Register on DDNS Encoder
Green Blinking, Red
Blinks Once every 5
Seconds
Video Loss in Encoder System
Constant Change
between Green,
Orange, and Red
Formatting USB Storage Device
LINK
OFF
No Connection to Remote System
Green
Connected to a Remote System
Red Blinking
Decoder Only: trying to connect to an
Encoder
Orange
Illegal Connection (unsupported
combination of system modes)
DATA
Green
Data Transmission in Progress
Red
Data Loss
OFF
No Data Transmission
Description of LED
System Status can be monitored with the LED Display:
User Manual VS-103E-3GSDI – V1.0Page 13 of 63 2/2016
Page 14
3.System Operation
Default ID: admin
Default Password: 1234
Default IP Address : http://192.168.10.100
3.1 Remote Video Monitoring
There are two ways to monitor video when the VMS (Video Management System) and
Video Encoder are connected. In order for a proper operation, an IP Address must be
set accordingly. Please refer to the VS Manager Manual enclosed with product for
further details.
Video Monitoring using Internet Explorer
Open Internet Explorer and enter the Video Encoder’s IP Address. The system will ask
for confirmation to install Active-X Control. Once authorized, Internet Explorer will begin
to display video images from the Encoder as shown below:
User Manual VS-103E-3GSDI – V1.0Page 14 of 63 2/2016
Page 15
3. System Operation
Video Select
Select the Video Stream to be viewed: Primary, Secondary, Tertiary or Quartic Streaming
This video encoder is capable of Dual Streaming; Primary Streaming and Secondary
View Size
Adjust the Screen Size. Screen size is initially adjusted according to the Compression Resolution. If you click 50% icon, the whole screen size will be reduced to half size.
Digital Zoom
Control the Digital Zoom on the screen. The more the encoder zooms
in, the smaller the square of control panel is. Position of the image can
be changed by moving position of the square. If you press “1x”, the
screen will return to the normal size.
PTZ Control (Optical Zoom & Digital Zoom Built-In Encoder)
PTZ Control Panel is used for controlling External PTZ devices
when the External PTZ devices are connected through a special
Serial Port. It is possible to control zooming by using the Zoom In/Out buttons of PTZ Control Panel. In order to use Digital Zoom,
select Digital Zoom “ON” in the EncoderTab)
- “Stop”
Stop on-going PTZ action.
- “Focus Near”, “Focus Far”, “Auto Focus”
Adjust the focus of the lens.
Select Preset
Set preset position and move to the specific preset position.
- GoTo: After set up, move to the selected preset entry.
- Set: Set the current position to the selected preset entry.
- Clear: Delete the selected preset entry.
Sensor Input and Alarm Input
Displays the status of the sensor in real time. This video encoder supports
One Sensor Input. When the sensor of the encoder is working, the
sensor light turns red. Operate the Alarm Device by pressing the number
icon. This encoder supports One Alarm Output. A number icon indicates the status of
the alarm device.
Streaming. Video will be displayed according to the resolution
set on video configuration. If Dual Streaming (“Use Dual Encode” Menu in Video page) is not activated, Secondary
Videos are not available.
User Manual VS-103E-3GSDI – V1.0Page 15 of 63 2/2016
Page 16
3.System Operation
IP Mode
Fixed IP
IP Address
192.168.10.100
Subnet Mask
255.255.255.0
Gateway
192.168.10.1
Base Port
2222
HTTP Port
80
Snapshot
Capture video images and save them as BMP or JPEG files.
Talk
Transfer audio from the PC microphone to the encoder.
File Record
Recording to an AVI file on Live View page is available. AVI files are generated in the
specified folder or in specified file name on the PC where the web browser is running.
1. Press “Set” button to select folder or create a new folder.
Enter the file name on Filename field.
2. Press “Start” button to start recording.
3. Press “Stop” button to end recording.
4. AVI file named “IP address_hh_mm_ss” or
“File name_IP address_hh_mm_ss” will be generated in the
specified folder depending on whether the path specified a folder or a prefix of the file
name.
Display Buffer
smoother video by sacrificing the latency. A setting of 10 ~ 15 frames can be generally
used for most situations.
Video Monitoring with Decoder System
When the Video Encoder’s IP Address is set in the Remote IP Address section of the
Decoder, the Decoder System will connect to the Encoder and start receiving the video
images. Normally, a monitor connected to the decoder will display video images.
Set the number of video frames to be buffered before being
displayed on web browser. Larger values result in
3.2 Initialization of IP address
User Manual VS-103E-3GSDI – V1.0Page 16 of 63 2/2016
If a System IP Address is lost, the system can be reset to the System Default IP
Address using the Reset Button to the left of the LED lights.
1. While system is in operation, press the reset button for more than 5 seconds.
2. The system will reboot automatically.
3. Once the system reboots, IP Address will be set to the System Default as below:
Page 17
4.Remote Configuration
4.1 System Configuration
Remote Setting is available by using web browser. Enter IP Address of the Video
Encoder and a Live View screen appears (see below). Press the Setup button located
in the upper right area of the monitoring screen for Encoder Setup. For Remote Setting,
the user should have manager-level authority or higher.
The configurations are grouped into 9 categories: Video & Audio, Image, Network, Event, Record, Device, PTZ, System, and User. To save configuration changes,
click “Apply”. Leaving the page without clicking “Apply” will discard any new
changes.
User Manual VS-103E-3GSDI – V1.0Page 17 of 63 2/2016
Page 18
4.Remote Configuration
4.2 Video & Audio Configuration
Information
The information provides current information for Video and Audio Settings.
Encode
- Performance Calculation
Shows the performance usage rate according to the value set at Encode mode.
- Input Format
Choose the appropriate Input Format from the list provided.
User Manual VS-103E-3GSDI – V1.0Page 18 of 63 2/2016
Page 19
4. Remote Configuration
- Resolution
Select the appropriate Video Encoding Resolution. The Scaling option is used
when the Encoding Resolution is different from Input Resolution. Without Scaling,
the input video will be cut according to the encoding resolution. If Scaling is
selected, the input video will be adjusted according to encoding resolution.
- Framerate
Determine the maximum number of frames per second for the video stream.
1,2,3,4,5,6,8,10,15,20,25,30 and 60 frame rate can be selected. The actual frame
rate of the video can be less than the maximum frame rate set due to the network
bandwidth limitation.
- Preference
Select Encoding Mode to control the video quality or bitrate: Quality (VBR) or Bit Rate (CBR). If Bitrate is selected, the video encoding will be prompted by the Bitrate
value entered. Therefore, the Bitrate mode corresponds to CBR (Constant Bit Rate)
encoding. If Quality is selected, the video encoding will be prompted by the quality of
image selected. Therefore, Quality mode corresponds to VBR (Variable Bit Rate)
encoding.
- Quality
Select Quality Level: 7 Levels of Quality are available. Quality Mode (VBR Encoding) encodes every frame in a constant quality. Therefore, resulting bitrate
may vary a lot depending on the complexity or activity changes in the input video.
Quality Mode is preferred when constant video quality is required and the network
bandwidth is enough for delivering the stream of highly varying bitrate.
- Bitrate
Bitrate value ranges between 32 and 16Mbps. Bitrate Mode (CBR Encoding)
allows you to set a fixed target bitrate that consumes a predictable amount of
bandwidth. In order to stay within the bitrate limit, video quality is controlled
dynamically according to the complexity or activity changes in the input video.
- I-Frame Interval
I-Frame Interval ranges between 1 and 255.
- H.264 Profile
Select the H.264 Profile : High Profile or Baseline Profile
1. High Profile
High Profile is the primary profile for broadcast and disc storage applications;
particularly for high-definition television application.
2. Baseline Profile
Baseline Profile is for low-cost applications that require additional data loss
robustness used in some videoconferencing and mobile application. This profile
includes all the features that are supported in the constrained baseline profile, plus
three additional features that can be used for loss robustness.
User Manual VS-103E-3GSDI – V1.0Page 19 of 63 2/2016
Page 20
4. Remote Configuration
- Secondary 1, Secondary 2, Secondary 3
- Use Dual Encode
Select ON to Enable and use Secondary 1-3.
The Secondary 1-3 video can be viewed on Live View window by selecting Stream Number on the Video Selection
- Algorithm
Select H.264 or MJPEG for the Secondary, Tertiary or Quartic Streaming.
When H.264 is chosen, Wither Bitrate Mode or Quality Mode can be selected for
Preference Mode IN. MJPEG supports Quality Mode only.
Audio
- Audio Source
Select the Audio Source: Embedded or Analog Stereo.
User Manual VS-103E-3GSDI – V1.0Page 20 of 63 2/2016
Page 21
4.Remote Configuration
Mode
Action
Off
No Operation
Tx-Only
Transmit Only
Rx-Only
Receive Only
Tx & Rx
Transmit and Receive
- Algorithm
Select the Audio Algorithm: G.711 or AAC. G.711 and AAC from client to encoder
direction are supported. Thus, bi-directional audio communication is supported.
- Sample Rate
The Sample Rate defines the number of samples per unit of time taken from a
continuous signal to make a discrete signal.
- Bitrate
Bitrate ranges from 64Kbps and 128kbps when AAC is selected. The sample rate is
fixed to 8KHz and 32KHz for G.711 and AAC respectively. Note: when the video
encoder is connected to a decoder, the decoder’s audio algorithm should be set
identically to transmit the audio properly.
- Mode
Select the Audio Operation Mode:
- Input Gain
Audio Input Gain ranges from 0 to 31.
Output
-Output FormatSelect theformat of output when Enable Preview is selected.
User Manual VS-103E-3GSDI – V1.0Page 21 of 63 2/2016
Page 22
4.Remote Configuration
4.3 Image Configuration
Codec
Brightness: Controls input video brightness by selecting values between 0 and 255.
Contrast: Controls input video contrast by selecting values between 0 and 255.
Hue: Controls input video hue by selecting values between 0 and 255.
Saturation: Controls input video saturation by selecting values between 0 and 255.
4.4 Network IP & Port Configuration
User Manual VS-103E-3GSDI – V1.0Page 22 of 63 2/2016
Page 23
4.Remote Configuration
Domain Name System (DNS) is a database system that translates a computer's fully qualified
domain name into an IP address. Networked computers use IP addresses to locate and connect to
each other, but IP addresses can be difficult for people to remember. For example, on the web, it's
much easier to remember the domain name www.amazon.com than it is to remember its
corresponding IP address (207.171.166.48). Each organization that maintains a computer network
will have at least one server handling DNS queries. That server, called a name server, will hold a
list of all the IP addresses within its network, plus a cache of IP addresses for recently accessed
computers outside the network.
IP Mode
Selection
Description
Fixed IP
Local IP
Fixed IP Address
Local Gateway
Gateway IP Address
Local Subnet
Subnet Mask
DHCP
N/A
- Local
Select the IP Mode: Fixed IP or DHCP
Depending on the selected mode, the following configuration applies:
Contact your ISP provider or network manager for IP address information.
- DNS
Obtain DNS Encoder Address automatically
Find DNS Encoder Address automatically when IP Mode is set to DHCP.
Use the following DNS Encoder Address
Enter the DNS Encoder IP Address: Primary or Secondary DNS Encoder
- IPv6
IPv6 Address: Enter the designated Ipv6 address.
IPv6 Subnet Prefix Length: Enter the bit number for the Ipv6 subnet.
IPv6 Default Gateway: Enter the designated Ipv6 gateway.
IPv6 Link Local: Display the Ipv6 link local.
- Port
Base Port (1025 - 65535)
Enter the Base Port Number: Network Base Port is used for communication with
remote clients. In order for the video encoder and remote systems to be connected,
the port number must be identically configured for the video encoder side and client
side.
HTTP Port (80, 1025 - 65535)
Enter HTTP port used for a web-based connection.
HTTPS Port (443, 1025 - 65535)
Enter HTTPS port used for a secured HTTP connection.
RTSP Port (554, 1025 - 65535)
Enter RTSP port used for RTSP-based connection. The default TRSP port is 554.
RTSP (Real Time Streaming Protocol) is a standard for media streaming
User Manual VS-103E-3GSDI – V1.0Page 23 of 63 2/2016
between encoder and client.
Page 24
4. Remote Configuration
- Multicast
The Multicast menu is used for configuring the Multicast IP Address where the
media stream is delivered when a Decoder, VMS or NVR software is connected in
the Multicast Mode. The Multicast IP Address selection range is between 224.0.0.0
and 239.255.255.255. The selection can be used only when the media protocol is
set to Multicast.
Discovery
- UPNP
When UPNP is ON, it allows the discovery of the client according to UPNP
(Universal Plug and Play) Protocol.
- Zeroconf
When Zeroconf is ON, it allows the discovery of the client according to Zeroconf
Protocol.
- WS Discovery
Discovery function based on web service is enabled. It allows the discovery by the
client SW which is supporting Onvif.
User Manual VS-103E-3GSDI – V1.0Page 24 of 63 2/2016
Page 25
4.Remote Configuration
One Way
- This IP Video Encoder provides two kinds of one-way (unidirectional) streaming
based on UTP to clients: RTSP and MPEG-TS. Both are types of broadcasting
where traffic from clients to an encoder is not generated at all.
- RTP (Real-Time Transport Protocol) is an Internet Protocol used for transmitting
single real-time multimedia data such as audio and video to a select group of
connected clients. Normally RTSP uses RTP to format packets of multimedia
content. The RTP menu is used when the RTP only is streaming without an RTSP
connection. RTP stream will be transmitted to the destination set. The SDP
(Session Description Protocol) file can be found in the encoder and a client can
retrieve it using the http connection.
Destination IP: Set the IP Address of the destination system receiving the RTP
Stream. If the system is a decoder, RTSP authentication information can be found in
the middle of the RTSP URL: rtsp://admin:1234@192.168.10.100:554/video1
Destination Port: Set the port of the destination system receiving the TRP stream.
User Name: Enter the user name that will be used as a session name in the SDP file.
File Name: Enter the file name that will be used as the name of the SDP file. When this
is entered, it can be accessed through http://ServerAddress/filename
- MPEG-TS is the standard format for the transmission and storage of audio, video,
and data, and is used in broadcast systems such as DVB and ATSC. Transport Stream is specified in MPEG-2 Part 1 Systems (formally known as ISO/IEC
standard 13818-1 or ITU-T Rec. H.222.0). Transport Stream specifies a container
format encapsulating packetized elementary streams with error correction and
stream synchronization features for maintaining transmission integrity when the
signal is degraded. Although MPEG-TS supports AAC as the audio algorithm, only
video is streamed when audio algorithm is set to G.711.
Destination IP: Set the IP Address of the Destination System which will receive MPEG-
TS stream.
Destination Port: Set the Port of the Destination System which will receive MPEG-TS
stream.
User Manual VS-103E-3GSDI – V1.0Page 25 of 63 2/2016
Page 26
4.Remote Configuration
Simple Network Management Protocol (SNMP) is used by Network Management
Systems to communicate with network elements. SNMP lets TCP/IP-Based Network
Management clients use a TCP/IP-Based internetwork to exchange information about the
configuration and status of nodes. SNMP can also generate trap messages used to report
significant TCP/IP events asynchronously to interested clients. For Example: a router
could send a message if one of its redundant power supplies fails or a printer could send
an SNMP trap when it is out of paper
SNMP
SNMP (Simple Network Management Protocol) is compatible with both SNMPv1 and
SNMPvec. Settings for using SNMP are as follows:
- SNMP Listen Port (0, 161, 1025 - 65535)
This port is for connecting an external device as an SNMP client. SNMP is not
used when the value is 0.
- SNMP Trap Destination IP
Set the SNMP Trap Destination IP.
- SNMP Trap Destination Port (0, 162, 1025 - 65535)
Set the SNMP Trap Destination Port. SNMP is not used when the value is 0.
User Manual VS-103E-3GSDI – V1.0Page 26 of 63 2/2016
Page 27
4.Remote Configuration
Dynamic DNS is a method, protocol, or network service that provides the capability for a networked
device, such as a router or computer system using the Internet Protocol Suite, to notify a domain
name server to change, in real time (ad-hoc) the active DNS configuration of its configured
hostnames, addresses or other information stored in DNS.
DDNS
Select DDNS (Dynamic DNS) Encoder to use. One of the two can be selected.
- DynDNS
DynDNS service is used in this mode. Refer to www.dyndns.org for details.
ID, Password and Domain name are needed when DynDNS is set.
- Vdyn
Vdyn is a DDNS service provided by Visionica (http://visionica.com). No further
configuration is required for using this service. It internally uses the MAC address for
the registration. When it succeeds, the domain name of the form
001C63A607EC.visionica.info is displayed on Current Domain entry of the Network
page. Email setting is not mandatory.
- Check IP Disable
If “Check IP Disable” is selected, it will skip to check it’s own IP. In Fixed IP Mode,
the set IP will be registered on the DDNS Encoder. In DHCP Mode, a dynamically
assigned IP will be registered on the DDNS Encoder. Normally Check IP Disable
should be unchecked in order to obtain the public IP in the network.
User Manual VS-103E-3GSDI – V1.0Page 27 of 63 2/2016
Page 28
4.Remote Configuration
IP Filtering
IP filtering is simply a mechanism that decides which types of IP datagrams will be
processed normally and which will be discarded.
Email
User Manual VS-103E-3GSDI – V1.0Page 28 of 63 2/2016
Page 29
4. Remote Configuration
Select the following when Email is selected as an Event Action:
Encoder Address
Enter an address of mail (SMTP) Encoder
Port
Specify a port for SMTP operation (Port 25 is the default port in SMTP operation).
If a port other that the default is configured in the SMTP Encoder, this port needs to
be changed accordingly.
Sender Address
Enter an account registered the in SMTP Encoder.
Authentication on SMTP Encoder
This function is applicable when the Email Encoder requires authentication for
sending Email.
ID & Password
When the Encoder requires authentication, ID and Password of an email account
need to be entered.
Destination Address
Enter Destination address. More than one address can be entered by delimiting
comma (,) or semi-colon (;). Destination addresses can take up to 63 characters.
Email Test
Email sending can be tested with this button. Please note that configured settings
should be saved first by pressing the Apply button before using the Email Test
Function. One of the following messages will appear as a result of the test:
- Email Notification
Video Clip Attaching
Video clips can be saved and attached as an AVI or JPEG file. When dual encoding
is enabled, Primary Video, Secondary Video (H.264 only) or JPEG Capture can
be selected. The number of JPEG frames is configured appropriately. This setting is
applicable only when JPEG Capture is selected.
Capture Interval
Select the interval of the captured frame.
User Manual VS-103E-3GSDI – V1.0Page 29 of 63 2/2016
Page 30
4. Remote Configuration
- FTP
When FTP is selected, specify the following:
Encoder Address
Enter an RTP Encoder Address to receive video files.
Port
Specify a Port for the FTP operation (Port 21 is the default port in the FTP
operation). If a port other than the default is configured in the FTP Encoder, this port
needs to be changed accordingly.
ID & Password
Enter ID and Password to access the FTP Encoder.
FTP File Name
The File Names uploaded by FTP can be specified by the user. If a fixed name is
specified, the file is overwritten repeatedly. Max length of a file name is 60
characters. If the name is left blank, file name is determined according to the
internal rule implemented in the firmware. The following macros are supported to
form variable parts of file names. These strings are case-sensitive.
%YYYY: year
%MM: month
%DD: day
%hh: hour
%mm: minute
%ss: second
%EVENT: event type (Sensor1, Motion, ...)
%ADDR: address of the encoder (Domain name when DDNS is used; otherwise IP address)
“.avi” or “.jpg” will be added automatically to the filename depending on the video file type
FTP Base Directory
User Manual VS-103E-3GSDI – V1.0Page 30 of 63 2/2016
Page 31
4. Remote Configuration
Specify the name of the directory to be created in the FTP Encoder. It is valid only
when Record is set to Use on the Record Session.
FTP Test
The FTP upload function can be tested with this button. Please note that the
configuration settings should be saved first by pressing the Apply button before
using the FTP Test Function. One of the following messages will appear after
testing:
- FTP Upload
Upload Video
When using Primary, Secondary, Tertiary or Quartic Video (H.264 only), JPEG
capture can be selected for uploading.
Number of Frame
Enter the frame number of the JPEG capture. (1 - 10)
Capture Interval
Select the interval of captured frame.
Continuous Upload
Continuous Upload ON allows video clips to be transmitted regularly regardless of
the event occurrence. When this mode is activated, the FTP upload by event is
suppressed.
Upload Duration
Specify the recording duration of the video clip to be transmitted (max 300 sec).
Upload Interval
Specify the transmission interval (max 3600 sec). Upload duration is not included in
the upload interval. For Example: if the upload interval is 60 sec and the upload
duration is 20 sec, a video clip for 20 sec is transmitted every 80 sec.
User Manual VS-103E-3GSDI – V1.0Page 31 of 63 2/2016
Page 32
4. Remote Configuration
This function is applicable when the E-mail Encoder requires encryption for sending
emails.
4.5 Event Configuration
User Manual VS-103E-3GSDI – V1.0Page 32 of 63 2/2016
Page 33
4.Remote Configuration
Action
Description
Beep
Triggers Beep Port
Alarm out
Triggers Alarm (Relay) Port
Email
Sends Email to the specified Email Address;
AVI File can be attached
FTP
Upload AVI File to a specified FTP Encoder
Preset
Move to the Preset Position
- Local
When a Decoder is connected to a Video Encoder, one system becomes a Local
System and the other a Remote System (generally a system which is being used by the
user is called as Local System). Event Actions can be configured from the Remote
System as well as the Local System. For Example: it is possible to turn on an alarm
device in the Local (center) Decoder System when a sensor device in Remote (site)
Video Encoder is triggered. The Local section configures the actions for the events from
the Local (self) System and the configuration activates the local devices and the
Remote sections configure the actions for events from Remote (peer) System.
The following table lists the possible actions for the events:
- Sensor1 / Sensor2
Configure the actions when the sensor is activated. Multiple actions can be set for a
single event.
- On Video Loss
Configure the actions when video input signal is lost. Multiple actions can be set for a
single event.
- On Motion
Configure the actions when motion is detected. Multiple actions can be set for a single
event.
- On Disconnect
Configure the actions when the link (connection) with peer system is disconnected.
Multiple actions can be set for a single event. This event happens when the last client
which has been receiving video from the video encoder loses the connection.
User Manual VS-103E-3GSDI – V1.0Page 33 of 63 2/2016
Page 34
4.Remote Configuration
Motion Detection
- Select the Use Motion Detection function
- Motion Detection Area Editing
Configure the region for Motion Detection. Regions of arbitrary shapes can be
configured by the following steps:
1. Select Enable on Edit Tab.
2. When selecting Editing Mode, Set includes the motion detection region cell and Erase
is for excluding cells.
3. Select cells by right clicking. Multiple cells can be selected by selecting and dragging.
4. Press Apply Edit Area to save the selection.
User Manual VS-103E-3GSDI – V1.0Page 34 of 63 2/2016
Page 35
4. Remote Configuration
When the Encoder can detect Audio Silence, the audio silence state is delivered to
the VMS as Audio Loss.
User Manual VS-103E-3GSDI – V1.0Page 35 of 63 2/2016
Page 36
4.Remote Configuration
Function
Operation
OFF
Not used
NO (Normally Open)
The port is normally open and activated when closed
NC (Normally Closed)
The port is normally closed and activated when opened
- Sensor Type
There are two Sensor Input Ports on the Video Encoder. Each Sensor Port can be
configured as follows:
The function of the sensor port is set based on the type of the sensor connected.
- Sensor Schedule
Choose Sensor OFF or Sensor ON and make a selection on the Sensor Schedule
Table to schedule according to day and time.
Alarm
Set the duration of the Alarm or Beep Activation in case of an event. If Continuous is
selected, the alarm will be in an active state until the operator resets it manually.
User Manual VS-103E-3GSDI – V1.0Page 36 of 63 2/2016
Page 37
4.Remote Configuration
4.6 Record Configuration
General
- Use Record
Off: Recording function will not be used when OFF is selected.
Use Disk: When the Use Disk function is on, the default setting for the Schedule
Table is Record Off.
Use FTP: Recording will be enabled and data will be uploaded to an FTP
Encoder. In this mode, the FTP Upload by Event is automatically disabled.
- Select Video
Select the Video Stream to record.
- Manual Record
When ON is selected, record is initiated regardless of Schedule.
- Overwrite
When the disk becomes full, the oldest data files are deleted automatically. This is
valid only when Use Record is set to Use Disk.
- Max File Size / Max File Length
Max File Size option is for limiting the size of the AVI file. If Small File Size is
selected, the file is generated but the number of small files will be increased. When
limiting the time length of the AVI file, the Max File Length option is used. If the file
size becomes the Max File Size or the duration of the recording reaches Max File
Length, a new file is created.
- Automatically Backup to FTP
Data recorded in the disk can be uploaded to an FTP Encoder automatically for
backup. FTP Encoder is configured on the Event page. This is valid only when Use Record is set to Use Disk.
- Erase After Backup
Data is deleted automatically after being uploaded to the FTP Encoder. This is valid
only when Automatically Backup to FTP is selected.
User Manual VS-103E-3GSDI – V1.0Page 37 of 63 2/2016
Page 38
4. Remote Configuration
- Start Time of Backup Data
Specify the time when the data backup occurs. Select Backup to FTP Disk. This
time is changed automatically with the Backup to FTP Encoder. Check current
backup status on a regular basis. This is valid only when Automatically Backup to FTP is selected.
- FTP Base Directory
Specify the name of the directory to be created in the FTP Encoder. This is valid
only when Use Record is set to Use FTP.
Checking Status of Recording
Recording Status can be checked on the main view page.
User Manual VS-103E-3GSDI – V1.0Page 38 of 63 2/2016
Page 39
4. Remote Configuration
- Event Type
Three recording modes are supported: Continuous, Event, and Disconnect.
When using Event Recording, Event Types can be selected among several Events.
Selected Event Type is used for configuring the Schedule Table. Up to 4 Event
Types can be configured and each Event Type can be a combination of Sensor,Video Loss and Motion Event.
Pre-Event Time
Specify the duration of recording before an Event happens.
Post-Event Time
Specify the duration after the Event is cleared.
- Schedule Table
Actual Recording Mode is determined by Schedule Table, where the Recording
Mode is configured by Day and Hour. Recording Modes are configured as follows:
Record Off
No Recording.
Continuous
Records continuously.
Disconnect
Recording is started when the system loses connection to the last client (Decoder,
VMS/NVR) etc. When there are multiple clients and only one is disconnected, the
recording is not started.
Event Type
A recording is started when an Event is configured in the Event Type.
User Manual VS-103E-3GSDI – V1.0Page 39 of 63 2/2016
Page 40
4. Remote Configuration
When SD Memory is used, at least 1GB is recommended. An EXT3 or FAT32 File
System can be used. EXT3 or FAT32 can be read in Linux PC. However, only disks
with FAT32 file system can be read in Windows PC. Less than 4Mbps of video bit rate
is recommended when you record and monitor video simultaneously since frame
dropping may occur due to performance limitation.
Restart the system after connecting an SD card. The system reads the disk status and
initializes during reboot. Once the disk initialization is finished, the disk status is shown
on the Record page of the web-based setup.
Refer to this chart for checking the disk status:
User Manual VS-103E-3GSDI – V1.0Page 40 of 63 2/2016
Page 41
4.Remote Configuration
Search Page
Recorded Video and Audio Data can be saved in AVI Format. In general, one AVI file
is created for an Event-Based Recording. However, it is possible that a Series of
Events can be recorded continuously and merged into a single AVI file depending on
Pre/Post Event Time Setting. The size of file is limited to 10-2GB. With Continuous
Recording, AVI files are created in a series and each size is limited to 10-2GB.
- Playback
1. When selecting an AVI file, a window will appear for opening or saving the file.
2. The Save button will store the file in the PC. The AVI file can be played with
Windows Media Player.
User Manual VS-103E-3GSDI – V1.0Page 41 of 63 2/2016
Page 42
4. Remote Configuration
3. The Open button will download and automatically play with Windows Media Player.
4. The internet connection is disabled during downloading. Two AVI files cannot
be download at the same time.
4.7 Serial Device Configuration
Information
This information provides current serial communication status.
User Manual VS-103E-3GSDI – V1.0Page 42 of 63 2/2016
Page 43
4.Remote Configuration
Serial Setup
- Serial Protocol:
Choose Video Encoder Serial Port: RS-232 or RS-422/485; Select RS-422 or RS-485
for the RS-422/485 port.
- Serial Port Configuration:
The Serial Port configuration is as follows (must be same as the connecting device):
User Manual VS-103E-3GSDI – V1.0Page 43 of 63 2/2016
Page 44
4.Remote Configuration
4.8 PTZ Configuration
General
PTZ Type
Select the type of PTZ Encoder or Receiver.
PTZ ID
Since it is possible to control multiple PTZ Encoders or Receivers with a single control
line, each Encoder or Receiver will be assigned with a unique ID. Enter the PTZ ID for
control. The ID value range can be between 0 and 255.
PTZ Port
Select the Serial Port for PTZ Encoder control.
Preset
User Manual VS-103E-3GSDI – V1.0Page 44 of 63 2/2016
Page 45
4.Remote Configuration
128 Preset Positions max can be defined.
- Select Preset Number: Select entry to be assigned to the current encoder position.
- Focus Mode: Select the Focus Mode after Preset Go To is selected.
Do Not Change: The current Focus Mode is not changed.
Focus Auto: Auto-focusing is selected after the Preset is moved.
Focus Manual: The current Focus Position is saved when Preset is set.
- Event Holding Time: Set the time to stay at the Preset Position when the Preset is
moved by the Event. If it is set to 0, the Encoder doesn’t return to the original position after moving to the Preset Position by Event.
- Edit Label: Assign a Label to the Preset Position. Only the first 15 Preset Entries
can have Assigned Labels (Preset-1 - Preset-15).
User Manual VS-103E-3GSDI – V1.0Page 45 of 63 2/2016
Page 46
4. Remote Configuration
The Video Encoder memorizes the combination of Presets, Pattern and/or Swings
sequentially and runs Presets, Pattern and/or Swings repetitively on activation. A max
of 8 Groups are programmable. Each Group can have a max of 20 actions which are
the combinations of Preset, Pattern and Swing. The Option field is different for Preset
and Pattern/Swing. For Preset, it configures the Preset Speed. For Pattern/Swing, it
configures the number of repetitions. Dwell time between actions can be set up as well.
1. Select one Entry within Group.
2. Select the Modify Group button. The following window will appear.
3. Set Action, Dwell Time and Option and click Enable.
4. Press Apply button and the Group can be used on the Live View Page.
User Manual VS-103E-3GSDI – V1.0Page 46 of 63 2/2016
Page 47
4.Remote Configuration
Advanced
- Advanced PTZ
Specify if the Video Encoder will continue the Previous Action such as Pattern, Swing
or Group after reboot.
ON: If Pattern, Swing or Group was running before rebooting, the Action is
resumed. If it was in the stopped state, it moves to the last position.
OFF: Moves to the initial position after rebooting.
- Auto Parking
Auto Parking returns to the previous Preset Position or resumes the operation such
as Pattern, Swing or Group when a specified time expires after the PTZ control is
stopped. Parking Time can be set from 0 to 3600 seconds and “0” means that the
Auto Parking function is turned Off.
User Manual VS-103E-3GSDI – V1.0Page 47 of 63 2/2016
Page 48
4.Remote Configuration
Privilege
Allowed Operations
Remarks
Admin
All Operations
User ID = admin
Manager
All Operations except for User
Configuration
User
Live Viewing and PTZ Control
Guest
Live Viewing Only
4.9 User Configuration
User List
User can be registered and privilege level of a user can be specified. User configuration
is allowed only to admin user. Max 16 users can be registered and each user can have
one of four privileges.
- Add User
Press Add button. The following window will appear.
Enter User ID and password (Up to 15 characters) and select Privilege Level.
User Manual VS-103E-3GSDI – V1.0Page 48 of 63 2/2016
Page 49
4. Remote Configuration
- Delete User
Select the User to be deleted and press Delete button.
- Change Password
Press Modify Password button. The following window will appear.
Enter the current password and then set a new password.
- Modify Privilege Level
Press Modify Privilege button to change User level. It is not allowed to change the
privilege level of admin user.
User Manual VS-103E-3GSDI – V1.0Page 49 of 63 2/2016
Page 50
4. Remote Configuration
- Login Policy
Skip Login provides for convenient access to the encoder when authentication is
not required. When Skip Login is set to Enable, login step is skipped. The privilege
level after login in this way is determined by the setting of Privilege Level After Login Skipped.
- Authentication
HTTP authentication based on RFC 2617(HTTP Authentication: Basic and Digest
Access Authentication) is supported.
4.10 System Configuration
- System information
This following Network Information is displayed (Read Only):
Model
Display the model name.
Version
Display the current firmware version.
Mac Address
Display the MAC address of the encoder. In case the video encoder is registered at
DDNS Encoder, the MAC address is used in DDNS registration.
Set Current Time
Display Current Date and Time
Current Domain
In case the encoder is registered at DDNS Encoder, the registered domain name is
displayed.
User Manual VS-103E-3GSDI – V1.0Page 50 of 63 2/2016
Page 51
4.Remote Configuration
Maintenance
- Firmware
Version: Displays the current firmware version.
Upgrade: Complete the following to upgrade the firmware:
1. Press Browse button to select a firmware file from PC.
2. Press Firmware Upgrade button to start upgrading.
3. A message for showing status (downloading / upgrading) will be displayed.
4. The video encoder will reboot automatically after completing upgrade.
Do not turn off the encoder during upgrading.
- Config Backup & Restore
Backup: All the setting of configuration can be stored.
Restore: Stored configuration can be browsed and restored. The encoder is
rebooted once the Config Restore button is selected.
User Manual VS-103E-3GSDI – V1.0Page 51 of 63 2/2016
Page 52
4. Remote Configuration
- Reboot Reboot the Encoder: Do not press the Reboot button unless the encoder needs
a reboot.
- Factory Reset
All settings including user accounts and logs are cleared.
- Factory Reset Except Network Settings
All settings except for current network settings are changed to the default values.
Time
Start Time
The latest encoder’s booting date and time.
Current Time
Current date and time.
Enter a new date and time then press Set Current Time button to update date &
time.
Time Format
Change the time format. The selectable time formats are as below;
1. YYYY/MM/DD hh:mm:ss (Eg. 2012/10.30 12:30:45)
2. DD/MM/YYYY hh:mm:ss (Eg. 10/30/2012 12:30:45)
3. MM/DD/YYYY hh:mm:ss (Eg. 30/10/2012 12:30:45)
User Manual VS-103E-3GSDI – V1.0Page 52 of 63 2/2016
Page 53
4. Remote Configuration
A Time Zone is a region of the earth that has uniform standard time, usually referred to as
the Local Time. By convention, time zones compute their local time as an offset from UTC
(Coordinated Universal Time). In casual use, GMT (Greenwich Mean Time) can be
considered equivalent to UTC. Local time is UTC plus the current time zone offset for the
considered location
The Network Time Protocol (NTP) is a protocol for synchronizing the clocks of computer
systems over packet-switched, variable-latency data networks. It is designed particularly to
resist the effects of variable latency by using a jitter buffer.
Time Zone
Select time zone of where the encoder is installed.
Depending on the time zone, Daylight Saving Time will work automatically
Automatic Synchronize with NTP Encoder
Synchronize the encoder time with an NTP Encoder using NTP (Network Time
Protocol). Name of the NTP Encoder should be registered on NTP Encoder Name.
System ID
User Manual VS-103E-3GSDI – V1.0Page 53 of 63 2/2016
Page 54
4. Remote Configuration
- System ID
Enter System ID that is used as a video encoder title.
The set System ID is displayed with video image on a Web Browser. The System ID
is also transferred to remote software, such as VMS, and displayed on it.
- Information Display
System ID and/or Video Encoder time can be display over the video window in
Internet Explorer. Each item can be turn on or off separately, and position also can
be configured. This information is displayed after the video is decompressed.
- Burn In OSD
Insert system ID and date/time in the compressed video. System ID and time
respectively can be turned on or off in the video. Position and Font size can be
configured also. System ID for BurnIn OSD exists independently from normal
System ID.
Note that size of Burnin OSD display varies according to the encoding resolution
setting. This is inevitable because Burnin OSD is inserted to the frames before
encoding is performed. The following table describes the rule for BurnIn OSD
display.
2: Both System ID and Time are displayed.
1: Either System ID or Time can be displayed. When both are enabled,
System ID is displayed.
0: No items are displayed. This is because video area is too small to display
OSD text in large text.
- User Defined OSD
You can enter any text you like independent.
X-Coordinate or Y-Coordinate
For example, if you enter 500, 500 values, OSD is placed in center of images.
User Manual VS-103E-3GSDI – V1.0Page 54 of 63 2/2016
Page 55
4.Remote Configuration
Language
- Language
Select the Language to be used for Web-Based Configuration.
User Manual VS-103E-3GSDI – V1.0Page 55 of 63 2/2016
Page 56
5. Using a VS-102 as a Decoder with VS-103
You can use the VS-102 as a Decoder but the Decoder will need to have
V1.305R01-T660_MEI.tus firmware installed at no charge for audio on the Decoder
to perform properly.
User Manual VS-103E-3GSDI – V1.0Page 56 of 63 2/2016
Page 57
6. VS Manager
VS Manager is a program used for basic configuration, diagnostics and firmware
upgrade of video encoders or IP Encoders. VS Manager provides the following
features:
Finding Encoders on the LAN and assigning IP Addresses.
Monitoring Server Status: Encoding/Decoding, Serial, Sensor, etc.
Diagnostic Function: PING, Network Bandwidth Measurement, Video/Audio Output,
For Windows 7, 64 bitONLY:
Once VS Manager installed, select IP Discovery, create servers.
On main page go to Tools, Options and change to this path below.
In the address window, after the word "Files" type a space then (x86).
User Manual VS-103E-3GSDI – V1.0Page 57 of 63 2/2016
Page 58
7. Data Sheet
VS-103E-HDSDI
1080p60 Full HD Video Encoder
User Manual VS-103E-3GSDI – V1.0Page 58 of 63 2/2016
Page 59
7. Data Sheet
User Manual VS-103E-3GSDI – V1.0Page 59 of 63 2/2016
Page 60
7. Data Sheet
VS-TRM-200 Rack mount holder for 16 pcs of VS-11
VS-TRM-202 Rack mount holder for 16 pcs of VS-102
VS-TRM-204 Rack mount holder for 16 pcs of VS-14
ACCESSORIES:
VS-TRM-200 / VS-TRM-202 / VS-TRM-204
Rack mount holder for mounting up to 16 VS Encoder / Decoders in a 5 RU space
Operating Conditions
Temp: 41-122° F / 5-50° C
Connections
Power: 100-240 VAC, 50/60 Hz, 1.6 A
Dimensions and Weight
Height: 8.3 in / 210 mm (5 RU)
Width: 19 in / 482.8 mm
Depth: 5.7 in / 145 mm
Weight: 14.8 lbs
*Shown with optional modules installed.
User Manual VS-103E-3GSDI – V1.0Page 60 of 63 2/2016
Page 61
8. Appendix
Appendix A: Sensor and Alarm Port
Sensor Port
Terminal Type
- Voltage Rating: 150VAC
- Current Rating : 2A
- Color : Red
Sensor Signal Input Type
- NO Contact Signals
Connection to External Device
Alarm Port
Terminal Type
- Voltage Rating: 150VAC
- Current Rating : 2A
Relay Type
- Contact Rating : 1A 30VDC
- Switching Power : Max 30W 62.5VA
- Switching Voltage : Max 60VDC
Alarm Signal Output Type
- NO/NC Contact Signals
Connection to External Device
User Manual VS-103E-3GSDI – V1.0Page 61 of 63 2/2016
Page 62
8. Appendix
Pin NO
Pin Name
Description
1
TX
RS232 TX(Transmit)
2
RX
RS232 RX(Receive)
3
GND
Ground
Pin No.
Pin Name
Description
1
RX-
RS422 RX-
2
RX+
RS422 RX+
3
TX-
RS422 TX- or RS485 TRX-
It is selectable by S/W Setup
4
TX+
RS422 TX+ or RS485 TRX+
It is selectable by S/W Setup
Appendix B: Serial Port
RS-232 Port
Terminal Type
- 3 PIN
- Pin Arrangement
Pin Description:
RS-422/485 Port
Port Type
- 4 PIN
- Pin Diagram
Pin Description:
User Manual VS-103E-3GSDI – V1.0Page 62 of 63 2/2016
Page 63
For Warranty information please refer to Marshall website page: