How it Works
Marmitek
Loading...
Gigavideo 40
Owner's Manual
16 pgs298.14 Kb0

Marmitek Gigavideo 40 Owner's Manual

120402IR • GIGAVIDEO 40
GIGAVIDEO 40
OWNER’S MANUAL 3
BETRIEBSANLEITUNG 6
MODE D’EMPLOI 9
GEBRUIKSAANWIJZING 12
GIGAVIDEO 40
J
2 MARMITEK
J
HI IE FCDDE
B
B
MARMITEK GIGAVIDEO 40 OWNER’S MANUAL
READ THIS FIRST!
Caution: to reduce risk of electric shock, do not disassemble any part of the videosender system.
No user-serviceable parts are inside. If you spill liquid on it, disconnect the unit from the AC outlet to prevent possible fire or shock hazard and consult authorized service personnel. Use only the supplied powersupplies. Defective parts must be replaced by original spareparts only.
Powerline operated equipment or accessories connected to the unit should bear the CE certification mark and should not be modified in any way that might defeat the safety features.
Warning: to prevent electric shock hazard, do not expose any part of the video Sender to rain or moisture. Do not use near a bath tub, swimmingpool, etc. Disconnect the unit during thunderstorms from mains and other connected equipment to avoid damage.
No guarantee or liability will be accepted for any damage caused due to incorrect use of the equipment supplied, other than indicated in this owner’s manual.
APPLICATIONS:
The Marmitek GIGAVIDEO 40 is designed to transmit audio and video signals, without running wires There is a second radio transmission system providing a infra-red return path enabling you to control your VCR or Satellite Receiver from a remote location.
• Watch a movie on any TV in Your home without moving your VCR or running cables
• Watch satellite programs on any TV anywhere in your house
• Watch DVD movies from your PC on your TV in a remote location
• Listen to MP3 audio from your PC on your Hifi system in the livingroom
• Monitor your sleeping baby, eldery or disabled on your TV by using your videocamera or CCD camera
• Make perfect demonstrations without wiring TV’s during trade-shows, seminars, etc.
1. SETTING UP THE MARMITEK
GIGAVIDEO TRANSMITTER:
1. Connect one set of Audio/Video cables to the VIDEO [C] and AUDIO [D] jacks of your Marmitek GigaVideo Transmitter. Take care to match the colors of the plugs on the cable with the jacks on the GigaVideo Transmitter.
2. Connect the other end of the cable to the Audio/Video OUT jacks of the video source you want to transmit the signal from (e.g. your VCR, DVD, Satellite or TV). If your video source is equipped with a SCART connector use the SCART Adapter labelled TRANSMITTER.
3GIGAVIDEO 40
Connecting the transmitter to your VCR or Satellite receiver, allows you to choose channels independent from your main TV. If the jacks are colored differently, connect the yellow plug on the jack VIDEO, the red plug on the jack AUDIO RIGHT and the white plug to the jack AUDIO LEFT.
3. Switch the Power slide switch on the side into the "OFF" position
4. Plug the supplied mains adaptor, labelled Sender/Transmitter 200mA, into a 230Volt -50Hz wall outlet and connect the jack to the 12V jack at the rear side of the transmitter. Only use the supplied mains adaptor!
5. Switch the Power switch to the ON position.
6. Set the Channel-switch [A] on A.
7. Position the transmitter in a convenient location and orient the antenna [K]
If you have several A/V components:
If you have two or more A/V components (e.g. VCR, Cable box, Laserdisc or satellite receiver) that you want to watch in another room, they will probably already been hooked up to the local TV in series. To connect the GigaVideo Transmitter you just need to indentify the last component in the chain and connect the Line OUT or scart to the GigaVideo Transmitter IN jacks.
2. SETTING UP THE MARMITEK GIGAVIDEO RECEIVER:
1. Connect a set of Audio/Video cables to the LINE OUT jacks [H+I] of your GigaVideo Receiver. Connect the other end to your TV. If your TV has a Scart connector, you may use the Scart adaptor provided; labelled: "Receiver".
2. Switch the Power slide switch on the side into the "OFF" position
3.
Plug the supplied mains adaptor, labelled Receiver 500mA, into a 230Volt -50Hz wall outlet and connect
4 MARMITEK
GIGAVIDEO TRANSMITTER
SCART ADAPTER
“TRANSMITTER”
the jack [E] to the 12V jack at the backside of the receiver. Only use the supplied mains adaptor!
4. Switch the Power switch [B] to the ON position.
5. Set the Channel-switch [A] on A.
6. Put the side antenna [J] of the remote control extender in an upright position.
3. FINE TUNING YOUR MARMITEK GIGAVIDEO SET:
Make sure your A/V equipment is switched on. Switch the receiving TV on and select the A/V channel (normally found on the "0" or "AV" button). The picture should now automatically be there, no tuning is required. The wireless GigaVideo usually works best with the indented faces of the antennas [K] on the Transmitter and Receiver unit look at one another. Sometimes however distance, reflections and other effects in the home may affect the signal so that some adjustment of either Transmitter or Receiver antenna may be necessary to get the best signal. If still experiencing difficulty, try changing the "ABCD" channel selector and change channels. Remember though both the receiver and transmitter must be on the same channel.
If you are not getting any signal at all:
Check that the units are connected to mains and that the Power-switch is in the ON position. Check that the Channel slide switch (labelled A-D) on both GigaVideo units is set at the same number. Check if the receiving TV is on the correct A/V channel. Raise the small black side antenna [J] to an upright position.
4. THE REMOTE EXTENDER FEATURE:
Your Marmitek VideoSender has the ability to transmit infrared signals from your own remote control from your receiving TV back to the equipment connected to videosender. For example, you can change channels on your satellite receiver while viewing in another room. Simply point your original remote control to the IR window on the front of your GigaVideo Receiver. The IR signal is now transmitted by radio to the GigaVideo transmitter.
Set up is simple, ideally with 2 people. Locate the mini IR emitter (the only item left now) and connect the small jack plug on the back of the Receiver (IR) You have to place the IR transmitter LED in front of the IR sensor of the equipment you want to control. For the best result you can experiment which position of the IR transmitter LED works best. If you have problems with the range, try to move the receiver and/or transmitter away from your connected equipment. This can greatly increase performance of the radio transmission.
Copyright © Marmitek X-10. The right is reserved to make technical modifications
5GIGAVIDEO 40
Loading...
+ 11 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use